Proposed Construction of Reception Building including Civil and Electrical Works at LCA Tejas Division towards Yemaluru Gate

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

PAN No.:

Goods and Service Tax ID No.

Contact details

Please Enter Contact person Name

Pls Enter Mobile No

Registered Contractor

Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs

I.T Returns for past 03 assessment years

Annual financial turn over during the last 3 years, ending 31st March 2025

TURN OVER IN Rs.

Pls Enter Turn over in Rupees for all the 3 years

ESI & PF Nos with proof

Remarks if any

Bank(s) details: [Copy of ECS and cancelled cheque leaf to be uploaded]

Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Solvency Certificate Details

Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender [Work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Please enter Details for Work No 1

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No II

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No III

Details of person holding the power of Attorney (If different from contact person)

Related Document to be Uploaded to eProcurement Portal

Pls Enter Details for Person holding Power of Attorney

DECLARATION I

DECLARATION II

Pls Accept the Delaration II

Specification

Demolishing RCC work by mechanical means and stock piling at designated locations and disposal of dismantled materials up to a lead of 10 kilometre outside HAL, stacking serviceable and unserviceable material separately including cutting reinforcement bars, after making temporary proetction for existing service lines, etc., all complete as directed by Engineer-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas in all kinds of soft / hard soil for foundations, footings, column pedestals or members as per the drawing and site requirement, etc., (exceeding 30cm in depth, 1.50m in width as well as 10Sq m on plan) including removal of vegetation and in-equalities, shoring, strutting for protecting the sides of foundation if required, removing slips or falls in excavation, forming steps in sides of deep excavations and their removal or covering up, levelling, ramming the bottom of excavation, getting out and disposal of excavated earth lead upto 50m and in all lifts with all labour, tools & tackles, plant & machinery, hire & fuel charges, etc., all complete as directed by Engineer-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains, pipes, cables etc. in all kinds of soils (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m with all labour, tools & tackles, plant & machinery, hire & fuel charges, dewatering if any, etc., all complete as directed by Engineer-in-Charge.

Returning / filling in with useful excavated soil (excluding rock), free from salts, organic or other deleterious matter (Other than black cotton soil & rock, etc., in trenches, plinth, sides of foundations spreading in layers not exceeding 20cm thick, watering, breaking / removing clods exceeding 50mm, ramming and consolidation of each deposited layer etc., with all labour, tools & tackles, plant & machinery, etc., lead upto 50m and for all lifts, etc., all complete as directed by Engineer-in-Charge.

Removing / transporting the surplus excavated earth including debris, vegetation waste, concrete waste, etc., to a distance upto 5000m from HAL premises to contractor's own yard including loading, unloading, depositing, spreading, levelling, etc., all complete as directed by Engineer-in-Charge.

Construction of granular sub-base (GSB) With material conforming to Grade-I (size range 75mm to 0.075mm) having CBR Value-30 by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, etc., all complete as directed by Engineer-in-Charge.

Supplying chemical emulsion (Chlorpyriphos / Lindane or any other equivaent make emulsifiable concentrate of 20%) in sealed containers including delivery as specified, etc., all complete as directed by Engineer-in-Charge.

Diluting and injecting chemical emulsion with 1% concentration for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Along external wall where the apron is not provided using chemical emulsion @ 7.50Litres / Sq m of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding, etc., complete the activity, etc., all complete as directed by Engineer-in-Charge. Note: The activity to be carried out trhough specialised agency who has registred under NCPI and who has executed similar services for Industrial Building Area.

Diluting and injecting chemical emulsion with 1% concentration for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25Litres per linear metre including drilling and plugging holes, etc., complete the activity, etc., all complete as directed by Engineer-in-Charge. Note: The activity to be carried out trhough specialised agency who has registred under NCPI and who has executed similar services for Industrial Building Area.

Supplying, mixing and placing plain cement concrete (1:3:6) of required thickness using 20mm down graded hard stone / granite aggregate in accordance with IS 456 in foundations, mass concrete, sub bases and other similar works excluding formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions, etc., but excluding the cost of centering, shuttering and finishing, etc., all complete as directed by Engineer-in-Charge.

Making plinth protection minimum 50mm thick of cement concrete 1:3:6, 20mm nominal size aggregate over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, etc., all complete as directed by Engineer-in-Charge.

Supplying, mixing and placing plain cement concrete (1:2:4) of required thickness using 20mm down graded hard stone / granite aggregate in accordance with IS 456 in Floor leveling / lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor, plinth, etc., excluding formwork, mechanical mixing, transporting, vibrating, consolidation, levelling, curing, dewatering if any, all materials, labour, lead & lift, tools, plant & machinery, keeping concrete well wetted during the curing period and protecting it in extreme weather conditions, etc., but excluding the cost of centering, shuttering and finishing, etc., all complete as directed by Engineer-in-Charge.

Providing and laying in position ready mixed or site batched design mix Cement Concrete of M25 grade with minimum cement content of 330Kgs / Cu m for reinforced cement concrete work like footing, pedestal, columns, beams, lintles, chajjas / canopies, staircases, sills, fins, shelves, flooring, stage, etc., using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength including pumping of concrete to site of laying, curing, carriage for all leads, etc., all complete as directed by Engineer-in-Charge. Note 1. Form work and reinforcement steel will be paid separately.

All works upto plinth level like footing, pedetsal, piles, plinth beam, drains including necessary openings and packing if any for laying pipes, cables, etc.,

All works above plinth level like column, beams, slabs, canopy, chajja, staircase, etc., level including necessary openings and packing if any for laying pipes, cables, etc.,

Formwork for Lintel Beams, window sills, etc., by providing timber, wooden planks, runners / MS sheets with all supports, struts, braces, wedges, scaffolds, bracings, ladders, gangways, dressing with oil including MS bolts nuts and washers, temporary openings, filleting for a stop, chamfered edges, internal / external splayed, rounded angles or grooves for forming throating including making temporary openings in the forms for pouring concrete, etc., as per drawing, etc., all complete as directed by Engineer-in-Charge. Note: Formwork material is contractor's own property and shall be removed after completion of work.

Foundations, footings, bases of columns for mass concrete, etc.,

For Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Supplying, straightening, fabricating and fixing Steel reinforcement of HYSD TMT bars of not less than Fe 500 conforming to IS 1786 for all concrete reinforcment members / works including cutting to length, bending to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with mild steel wire (Annealed) not less than 0.90mm dia or securing with clips, including fixing and bracing, wastage, welding, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it, etc., complete all as per specifications, drawings and as directed by the Engineer-in-Charge. Note: 1. For measurement, the weight of steel sections, plates, reinforcement steel bars, wire fabrics, etc., shall be calculated from the tables given in relevant Indian standards or actual whichever is less. Where the weight is not given in Indian standards, it shall be calculated at 7850 kg/m³. No tolerance on account of rolling margin shall be allowed on the nominal weight of steel sections.

Providing and fixing Stainless steel (Grade 304) railing / door handles / ballasters made of Hollow tubes, square bars, channels, plates, etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement, etc., all complete as directed by Engineer-in-Charge. (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing MS grills with mesh of required pattern to steel windows / walls / in frames of windows, ventilators, etc., and approved design using MS structurals such as MS flats, angles, round / square bars, etc., including necessary cutting, welding, embedding in concrete, masonry, etc., including priming coat with approved steel primer, etc., all complete as directed by Engineer-in-Charge.

Providing and laying masonry with factory made Precast concrete solid blocks of 200mm thickness of grade M10 made of Normal / C & D waste from approved manufacturer in superstructure above plinth level up fifth floor level (As per Industrail buildng floor heights) with Cement mortar (1:6) including required stagging, each course in true level & racking out joints, curing and cleaning, etc., all complete as directed by Engineer-in-Charge.

Providing and laying half block masonry with factory made Precast concrete solid blocks of 100mm thickness of grade M10 made of Normal / C & D waste from approved manufacturer in superstructure above plinth level up to +10m height with Cement mortar (1:4) including required stagging, each course in true level & racking out joints, curing and cleaning, etc., all complete as directed by Engineer-in-Charge.

Plastering to ceiling with 12mm thick on the rough side with cement mortor (1:4) including leveling, curing and making the level smooth and at all heights and execute the work, etc., all complete as directed by Engineer-in-Charge.

Plastering to internal brick / block wall with 15mm thick on the rough side of single or half brick wall of cemnet mortor (1:6) including leveling, curing and making the level smooth and at all heights, plaster drip course / groove in plastered surface or moulding to RCC projections and execute the work, etc., all complete as directed by Engineer-in-Charge.

Providing and applying internal wall and ceiling painting with two coats of premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50grams / Litre after applying white cement based putty of average thickness 1mm over the new plastered wall / ceiling / existing surface including preparation of the surfces by scrapping existing paint / stains with a coat of low VOC primer with emery paper to bring to smooth and even including applying additional coats wherever required to achieve even shade and colour of approved brand, etc., all complete as directed by Engineer-in-Charge.

Plastering to external brick / block wall with 18mm cement plaster in two coats under layer 12mm thick cement plaster on the rough side with cement mortor 1:5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement : 6 fine sand) including leveling, curing and making the level smooth and at all heights, plaster drip course / groove in plastered surface or moulding to RCC projections and execute the work, etc., all complete as directed by Engineer-in-Charge.

Providing, applying and Finishing walls with Acrylic Smooth exterior paint of required shade with Two or more coat applied @ 1.67Ltr / 10 Sq m over and including priming coat of exterior primer applied @ 0.90Litre / 10 Sq m) over the plastered wall / existing surface including preparation of the surfces by scrapping existing paint / stains, to achieve even shade and colour of approved brand, etc., all complete as directed by Engineer-in-Charge.

Providing and applying synthetic enamel paint of approved brand and manufacture of required colour to give an even shade in One or more coats on old work by cleaning and srcapping to make the surface smooth before appling paint, etc., all complete as directed by Engineer-in-Charge.

Providing & fixing Stainless steel (grade 304) Fly proof wire gauze of 0.50mm dia wire and 1.40mm aperture on both sides to windows, clerestory windows & doors with MS Flat [15 x 3]mm and nuts & bolts, etc., all complete as directed by Engineer-in-Charge. Note: Item to be opearted for louvered ventilators to protect from birds menance.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes, etc., for fixing required door fittings, etc., all complete as directed by Engineer-in-Charge.

Filling the gap in between aluminium frame & adjacent RCC / Brick / Stone work by providing weather silicon sealant over backer rod of approved quality upto 5mm depth and 5mm width as per architectural drawings, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing chromium plated brass minimum 100mm mortice latch and lock with 6 levers or standard suitable for doors as per site condition and a pair of lever handles of approved quality with necessary screws, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for fixed and sliding type (doors, windows, ventilators) and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately)

Supplying and fixing 12mm thick toughened glass of approved colour in UPVC / Alluminum frames either for doors, windows, partitions, etc., as per the architectural drawings including gasket & necessary beedings as per IS standards, etc., all complete as directed by Engineer-in-Charge.

Supplying and fixing of SS Screws of sizes for structural glazing / ACP Cladding and Coping for anchoring the frames for rigid support as per site condition, etc., all complete as directed by Engineer-in-Charge.

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns / floors and slabs to introduce steel bars for sunshades / balconies / kerbs including fixing the steel bars in position using epoxy resin anchor grout of pproved make but excluding the cost of reinforcement, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing of aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. for Semi Unitized System with use of minimum Vertical MULLION of section [81.16 X 67 X 1.80]mm and Horizontal TRANSOM [81.16 X 67 X 2]mm with Al. Cleats fixed with anchor bolts of M 10 X 9 and 8mm SS Bolts 8mm. The al.profiles shall be supplied with protective tapes and to be removed after completion of the work. (The item includes cost of material such as cleats, sleeves, screws, etc., necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing with 6mm thick Single Reflective Heat Strengthened from approved make of Glass (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, etc., all complete as directed by Engineer-in-Charge. [Glazing Only will be paid in this section of work. However, the submission of Design and Design Basis Reports is part of the specification for Semi Unitized Glazing System Please Refer Notes Indicated below:] (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure) including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates, etc., gaskets, screws, toggles, nuts, bolts, clamps, etc., structural and weather silicone sealants, flashings, fire stop (barrier) - cum - smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Extra for openable side / top hung vision glass panels / Refelcetive Panel including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, minimum 4 - point cremone locking sets with stainless steel plates, handles, buffers, etc., including necessary stainless steel screws / fasteners, nuts, bolts, washers, etc., all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Designing, fabricating, testing, installing and fixing in position Curtain Wall system comprising of ACP of approved colour and design with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels, etc., and with structural sealant, including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.50mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods, etc., and also with 6mm thick high performance glass.

Providing and fixing Granite stone slab of with (18mm to 25mm thick), area of slab not less than 0.50Sq m, like Ruby Red / Black / Cherry with gang saw cut, mirror polished, premoulded and prepolished, machine cut for platforms, vanity counters and similar types of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 , joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish, etc., complete at all levels as per direction of Engineer-in-Charge.

Providing and laying Leatherite finish or Flame finish Granite stone flooring (Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent) in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, etc., all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing 18mm thick granite of gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, facias and similar locations of required size approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including bull nosing, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish, etc., all complete as directed by the Engineer-in-Charge.

Providing and laying Double Charged vitrified floor tiles of size of [600 X 600]mm or nearest availabe sizes, in floors over a screed of cement mortar (1:4) 20mm thick for Paper Joint (Thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 course sand), including grouting the joints with grey cement slurry @ 3.30 Kgs / Sq m including grouting the joints with white cement and matching pigments, etc., all, complete as directed by the Engineer-in-Charge.

Providing and laying Glazed Vitrified tiles in Skirting / cladding over a screed of cement mortar (1:3) - Size of Tile [600 x 600]mm or nearest size available (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.30 Kgs / Sq m including grouting the joint with white cement & matching pigments, etc., all, complete as directed by the Engineer-in-Charge. For skirting,wall cladding inside pantry / wash area / Toilets.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30Kgs per Sq m, including pointing in white cement mixed with pigment of matching shade, etc., all, complete as directed by the Engineer-in-Charge.

Providing and laying Glazed Vitrified tiles Matt / Antiskid finish of size approximate size [600 X 600]mm or site required size, finish with Paper Joint in different sizes (Thickness to be sepcified by the manufacturer) with water absorption less than 0.08% and confirming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement: 4 course sand), including grouting the joints with grey cement slurry @ 3.30 Kgs / Sq m including grouting the joints with white cement and matching pigments, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type WC pan) of approved brand with ISI marked white solid plastic seat and lid, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all connecting fittings and fixtures to make it operational completely, including cutting and making good to the walls and floors wherever required, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Wall hung half pedestal Vitreous China Wash basin size of approximate size [630 x 450]mm fixed with with CI brackets / rack bolts , single 15mm CP brass pillar taps, 32mm CP brass waste coupling of standard pattern, PVC waste pipe with waste fittings of 40mm dia and make it function of approved brand / make, including painting of fittings and brackets, cutting and making good the walls wherever required, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing 15mm nominal bore dia CP brass bib cock of approved quality conforming to IS as suiatbel to site conditions, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing PTMT shelf / Towel rails 440mm long of approved quality and colour, weighing not less than 300gms or nearest available size complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing bright finished brass hard drawn hooks (coat hooks) and eyes of 300mm size, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing toughened glass shelf of approved make with approximate size [600 x 120 x 5]mm with edges round off, supported on anodised aluminium angle frame with CP brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc., complete as per direction of Engineer-in-charge.

Providing and fixing 8mm dia CP / SS Jet (Health Fuacet) with flexible tube upto 1 metre long with SS triangular plate on walls / Eureopean type WC material of approved make and quality, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing CP brass toilet paper holder of approved brand and fixing with screws,raw plugs, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing beveled edge mirror of approximate size [600 x 450]mm of superior glass quality complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers, etc., all, complete as directed by the Engineer-in-Charge.

Constructing masonry Chamber [60 x 60 x 75]cm inside or outside (or approximate size as per site condition), in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 18.33.1 With common burnt clay FPS (non modular) bricks of class designation 7.5, etc., all, complete as directed by the Engineer-in-Charge.

Providing, fixing, testing and commissioning trap (floor trap) of approved make with 100mm inlet and 75mm outlet of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors, connection with PVC soil / waste pipe, necessary 150mm thick cement concrete (1:2:4) for embedding the trap, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Single socketed pipes of 110mm diameter unplasticised Rigid PVC water pipes conforming to IS : 13592 Type A of approved brand, on wall / floor face including bends, collars, elbows, shoe, etc., jointing with / without seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Concealed Chlorinated Polyvinyl Chloride (CPVC) pipes of approved brand, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, fixing the pipe with clamps at 1.00m spacing, necessary reducers, tank adaptors, etc., This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints and making good the walls, etc., all, complete as directed by the Engineer-in-Charge. Note: Dual plumbing line to be executed for Water closets

15mm nominal dia Pipes

20mm nominal dia Pipes

Providing and fixing Extrenal exposed Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints, etc., all, complete as directed by the Engineer-in-Charge. Note: Dual plumbing line to be executed Water closets.

25mm nominal dia Pipes

32mm nominal dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Single socketed pipes of 110mm diameter SWR pipes of Type B confirming to IS 13592 of approved brand for Urinal, Basin & EWC out lets including bends, collars, elbows, shoe, etc., jointing with / without seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Single socketed pipes of 75mm diameter SWR pipes of Type B confirming to IS 13592 of approved brand, on wall / floor face including bends, collars, elbows, etc., jointing with / without seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen / pantry sink of size [510 x 1040]mm bowl depth 250mm with drain board as per IS:13983 with CI brackets and stainless steel plug 40mm, PVC waste pipe with waste fittings of 40mm dia, making it completely operational, including painting of fittings and brackets, cutting and making good the walls and wherever required, etc., all, complete as directed by the Engineer-in-Charge.

Providing and laying Non Pressure NP-2 class 300mm dia RCC pipes including collars / spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc afetr curing the joints, etc., all, complete as directed by the Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door / window / Clerestory windows & other Frames / Chowkhat of size [45 x 70]mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kgs / Cu m, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast / lugs / SS dash fasteners of required dia and length, etc., all complete as directed by Engineer-in- Charge. Note: For WPC solid door / window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter (minimum 30mm thick) of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Khs / Cu m and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing 12mm thick commercial ply conforming to IS : 1328 BWR type plain lining / with pattern / grooves with necessary screws / nuts & bolts / nails / fastners, including a coat of approved primer on one face, and fixed on wooden /steel frame, etc., all complete as directed by the Engineer-in-Charge. (If Frame work is carried out shall be paid for separately under wooden frames item). For wall Paneling, partitions, shelves, ceiling, etc.,

Providing & Fixing decorative high pressure 1.0mm thick laminated sheet of plain / wood grain in gloss / matt / suede finish to required pattern and combination as per the drawings, etc., on plywood with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality / brand, etc., all complete as directed by the Engineer-in-Charge. For wall partitions, paneling, ceiling designs, display shelves, etc.,

Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws, etc., on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS : 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer, etc., including necessary nails, screws, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine, etc., with auto closing spring loaded hinges (hydraulic type), etc., all complete as directed by the Engineer-in-Charge. (Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing stainless steel fancy handle upto 200mm long of approved make fixed with SS screws, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make / brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500mm long with screws, etc., all complete as directed by the Engineer-in-Charge.

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel, etc., all complete as directed by the Engineer-in-Charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels, etc., Payment of providing and fixing telescopic channel shall be paid separately)

Providing and laying Integral cement based water proofing treatment (With average thickness of 120mm and minimum thickness at khurra as 65mm) including preparation of surface as required for treatment of roofs, balconies, terraces, etc., consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 Kgs / Sq m of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-Charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-Charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-Charge to required slope and treating

Providing and fixing mineral fibre false ceiling tiles at all heights of size [595 X 595]mm of approved texture, design and pattern with 16mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.60. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33mm thick (galvanized @120 gsm) comprising of main T runners of [15 x 32]mm of length 3000mm, cross T of size [15 x 32]mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600mm to form grid module of size [600 x 600]mm suspended from ceiling using galvanized mild steel item (galvanised @ 80 gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6mm diameter fully threaded hanger rod up to 1000mm length and L-shape level adjuster of size [85 x 25 x 2]mm, spaced at 1200mm centre to centre along main ‘T’.

Providing and fixing FALSE CEILING with 12.50mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks of approved brand) at all height including providing and fixing of frame work made of special sections, power pressed from MS sheets and galvanized with zinc coating of 120 gms / Sq m (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.60mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.50mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of [25 x 10 x 0.50]mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate GI channels [45 x 15 x 0.90]mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.50mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.50mm, at 450mm centre to centre, shall be fixed in a direction perpendicular to GI

Supply and Fixing Acrylic 3D (Three dimension) letters "LCA TEJAS DIVISION" or " RECEPTION BLOCK" any other equivalent Letters with lights on 1-inch MS square pipe with all required accessories, etc., all complete as directed by Engineer-in-Charge.

Supply and Fixing Acrylic 3D(Three dimension) letters "HINDUSTAN AERONAUTICS LIMITED" any other equivalent Letters with lights on 1-inch MS square pipe with all required accessories, etc., all complete as directed by Engineer-in-Charge.

Providing and fixing factory made 3 track UPVC glazed / wire mesh windows comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of min 1.50mm and upto 2.10mm for Using R3 series with frame Approximate size of (98mm & above and upto 112mm) x (40mm & above & and upto 52mm) or nearest available, both glazed and fly screen sash Approximate size of (55mm & above and upto 66mm) x (30mm & above and upto 43mm) or nearest available, with zinc alloy (zamak) powder coated handle on every glazed panel along with suitable locking system (touch lock, etc.,), (Height upto 1.80m). conforming to EN: 12608 in any shape, white colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD

Manufacturing, providing and fixing factory made UPVC glazed Fixed Partition / window / Ventilator at all levels with / without mullion / transom comprising of lead free uPVC multi-chambered frame, sash and mullion / coupler (where ever required) extruded profiles having minimum wall thickness of min 1.70mm for series R1, R2 profiles and min 2.10mm for series R3, R4 profiles with frame sizes as mentioned below, glazed, conforming to EN: 12608 in any shape, Natural white colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws, etc.,

UPVC glazed fixed type Partition / Window / Ventilator of approximate size [1.50 x 1.50]m Using R3 series with frame (55 mm & above) x (45mm & above) & mullion (55mm & above) x (65mm & above). (Height upto 2.50metre) Note:- The rate is including including providing & fixing Glass.

UPVC glazed fixed type Ventilator with louvers of Approximate size [0.60 X 0.90]m using R1 series with frame Approximate size of (33mm & above) x (35mm & above) or nearest available & mullion (33 mm & above) x (50 mm & above) or nearest available, if necessary. (Height upto 0.9 metre) Note:- The rate is including providing & fixing louvers and 5mm thick glass.

Supplying and fixing of UPVC openable (single / double leaf) multichambered and stiffened /reinforced framed door with profile colour as natural white color of the following specifications: Casement door double panel / single panel with french (false) Mullion, if necessary with Zinc alloy (Zamak) 3D hinges (4nos), suitable locking system, Zinc alloy (Zamak) powder coated handles on both sides. Using R3 series with outer frame Approximate / nearest available size of (60mm & above upto 76mm) x (58mm & above upto 62mm) x (2.20mm and above) and shutters with approximate profile sections : (84mm and above upto 102mm) x (60mm and above upto 70mm ) x 2.20mm and above or nearest available size. The corners of all the profiles of frames and shutters shall be homogenously fusion heat welded without any gaps. The shutters shall have necessary handles, locking and other associated fittings to facilitate smooth operation. Both frame and shutters shall be reinforced with GI profiles of thickness 1.25mm.

Rupees Fifty Lakh Eight Thousand Three Hundred Seventy Nine and Twenty Two Paise Only

Supplying, Installation, Testing & Commissioning of 36W Panel light 2x2 ft., of Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) <19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). (As per CPWD Specification).

Supplying, installation, Testing & commissioning of following wattage LED Recessed/surface Down lighter (Round) SMD type Powder coated die cast /Extruded aluminum body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with driver efficiency >85%, Operating voltage AC 140-270volt, freq 50/60 Hz, operating temp range-15 deg to 40 deg centigrade internal surge protection of 2.5KV with Short & Open circuit protection, THD <10%, P.F≥0.95, IP20, CRI>80, UGR (Unified Glare Rating)<19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends, CCT 3000°K/ 4000°K/5700CK/ 6000°K/6500°K (As per ANSI Bin), SDCM(Standard deviation color Matching)<3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (T.C). Manufactures word mark/name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. As required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/watt output. LM79 & LM80 Test report from NABL Lab for all testing required for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-In–Charge as per requirement.(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90C). (As per CPWD Specification).

Supply, fixing directly to the ceiling/wall using suitable mounting arrangements testing & commissioning of surface mounting Decorative type 10W LED mirror light fitting, including driver, the driver shall have PF >0.9 and Colour temprature shall be ≥5700K, THD <20% operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections complete in all respect and as directed by EIC. The lighting fixture may be Havells: LUMILINENXTBS10WLED830SPCWH/ Equivalent make in other approved makes.

Supply, fixing directly to the ceiling/wall/Floor/false ceiling using suitable mounting arrangements testing & commissioning of 5mtrs length of LED strip including suitable rated driver having reliable performance with professional design for Decorative lighting applications (Cove lighting) and Colour temperature shall be 3000K/4000K(as per site requirement), operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting strip complete in all respect and as directed by EIC. The lighting strip may be model no: Havells model no: FLEXISTRIP5MIP2024V/2ALED or Equivalent make in other approved makes.

Supply, installation, testing & commissioning of Industrial type heavy duty Exhaust Fan (1 phase) of 300mm dia of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge.

Supply, installation, testing & commissioning of 200mm dia PVC type Exhaust Fan with louvers, minimum air delivery of 850CMH, connecting cord with 6A, 3 pin plug top and with all necessary accessories, complete in all respects and as directed by Engineer-in-charge. The exhaust fan may be Havells model no: Ventil air DX HS or equivalent in other HAL approved makes and as directed by Engineer-in-charge.

Distribution Boards

8way VTPN MCCB DB.

Supply, fixing, testing & commisisoning of following rating MCCB/MCB/RCBO in the existing Distribution board/powder coated enclosure as directed by Engineer-in-Charge.

63-100A 25kA FP 415V, MCCB

40-63 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity.

5A to 32A TP MCB, C Curve , 10 KA breaking capacity.

5A to 32A SP MCB, C Curve, 10 KA breaking capacity.

Supply, laying, testing & commissioning of following size Aluminium LT armoured power cables.

3.5CX 50 Sqmm Aluminium armoured conductor

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE armoured aluminium conductor cable of 1.1 KV grade as required

3.5C X 50 sq. mm Al arm cable

Wiring for light point / fan point / exhaust fan point/call bell point from nearest switch box with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, fan regulator, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (as per detailed CPWD specifications for Group C wiring)

Wiring to single light point/Fan point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects.

Wiring to two light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects.

Wiring to three light point controlled by 1 No 6A, 250V gr. flush modular type SP switch complete in all respects.

Wiring to exhaust fan point using 6A, 250V gr. flush type modular SP switch housed along with other lighting switches/separate switch box if required and 3pin 6A, 250V gr. modular type socket housed near the exhaust fan complete in all respects.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2sets of 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

25MM PVC Conduit

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

3 x 2.5 sq. mm

3 x 4 sq. mm

Supply and fixing on wall/ partition wall using necessary mounting arrangements for 105x50mm size DLP-PVC adaptable trunking system for laying power and Data/Telephone cables/wires with full top cover, necessary accessoires such as end caps, flat angle, T joints, external/internal angle, flat junction, Body joint, cover joint, required cabling accessories etc., complete in all respects as directed by Engineer-in-charge.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed by Engineer-in-Charge.

Data Items

Supplying, drawing, Installation, Testing and commissioning of 2runs of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc. complete as required

Supply & fixing in flush with wall/on Aluminium partition as per site condition, testing & Commissioning of 2nos of 1 Module RJ-45 sockets for Two numbers of Data points including supply of suitable size modular type MS concealed/open mounting box with base plates, front covers, etc., with necessary interconnections and chipping the wall, replastering to smooth finish etc., wherever required complete as directed by Engineer-in-charge.

Supply and laying of 50mm dia, PE-80, PN6 ISI marked HDPE pipe confirming to IS 4984:19955 including suitable jointing using welding as required in the excavated trench/duct/at road crossings for encasing cables complete in all respect as directed by Engineer-in-charge.

Supply & drawing of 0.5 mm dia copper conductor PVC insulated 4 pair colour coded and twisted unarmoured telecommunication cables in the existing PVC conduit as per standard practice including necessary inter connections & end terminations. As per CPWD Specification.

Supply, Fixing, in the existing GI /PVC box as per site requirement, testing & Commissioning of 1 No. Twin RJ-11 telephone socket outlets with shutter with necessary interconnections complete as directed by Engineer-in-charge.

Supplying , Installation, Testing and Commissioning of 1.5 TR with 5 Star BEE Rating Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 500C (out door ambient temperature). (As per CPWD Specification.)

Rupees Four Lakh Twenty One Thousand Thirty Seven and Sixty Paise Only

Rupees Fifty Four Lakh Twenty Nine Thousand Four Hundred Sixteen and Eighty Two Paise Only

Approximate Amount Put to Tender

Rupees Nine Lakh Seventy Seven Thousand Two Hundred Ninety Five and Two Paise Only

Rupees Sixty Four Lakh Six Thousand Seven Hundred Eleven and Eighty Five Paise Only