PROVISION OF CERTAIN MINOR AND REV WORKS AT NABHA UNDER GE (SOUTH) PATIALA

Amount

'Notes: (i) Please refer Schedule 'A' Notes of tender documents.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, getting out in any type of soil etc. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, excavated soil in trenches after pipes have been laid and tested, complete all as specified and directed.

Removing excavated surplus spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for cutting of road /PCC path upto the depth of pipe & making good the disturbed surface with PCC 1:2:4 (20 mm aggregate) 15 cm thick using extra cement including earth work complete all as specified and directed.

S&F Ductile iron water pipes 100 mm bore class K-7 conforming to IS-8329, in any length including jointing with push on rubber tyton joints, as in trenches complete all as specified and directed. Note: DI specials & Rubber tyton joints etc shall be included in the unit rate quoted.

S&F DI iron fittings of size upto 100/150 mm bore for spigot and socketed pipes e.g. Bends (any type, radius and angle). Tapers any type (Straight, end, increasing, decreasing or double socket etc). Tee pieces single branch, 'Y' junctions double branches, crosses (all sockets or socket and spigot) collars caps and plugs conforming to Is complete all as specified and directed. Note: Excavation, earth work, & joints shall be measured and paid separately)

M&L for Cutting existing cast iron pipe of 100 mm bore of any description for insertion of fittings and setting the pipe in proper alignment complete including cost of PCC work after completion of tubing work all as specified and directed. Note: Excavation earth work and fittings shall be measred and separately.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in cm 1:4 with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius complete all as Specified and directed

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate, as in foundation etc. complete all as specified and directed.

M&L for 40mm thick 1.2.4 type B-0 Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for 15mm thick cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finish complete all as specified and directed. Note : Water proofing compound shall be measured and paid saparately

Supply only integral water proofing compound ISI marked. complete all as specified and directed.

M&L Preparation of new plastered or unplastered surfaces of walls, two coats of cement base paint over a coat of cement primer complete all as specified and directed.

S&F Fe-410 (Gde E-250) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening complete all as specified and directed. Note - Removing of old gate fixing new steel gate of hold fast , finish the surface included in this item.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

M&L for Rolled sections of Fe 410-W (Gde E- 250) quality A as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates etc complete all as specified and directed

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position including closing after filling all as specified and directed

M&L for hardcore of gauge n.exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface using broken stones or boulders, complete all as specified and directed.

M&L for PCC (1:3:6), 50mm thick as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring., complete all as specified and directed.

M&L for machine pressed precast concrete inter locking paver block any shape and size made of M-35 grade concrete (with grey cement and no pigment) of 60mm thickness with 6mm top layer of anti abrasive material laid over 25mm thick (compacted) fine sieved sand complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out soft/loose soil, getting out, including removal for surplus/excavated soil to be distance not exceeding 50 mtrs,complete all as specified and directed.

S&F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws complete all as specified and directed.

M&L for rolled sections as in main and cross beams, hip and jack rafters purlins, where connected to common rafters and running rails and guides for slinding doors, fixed with angle cleats or other connecting plates to Fe-290 (Gde E-165) complete all as specified and directed.

M&L for Preparation new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide as in primer all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for ceramic tiles floor tiles of minimum size 600X600 mm 8 to 10mm thick in flooring etc set and jointed in neat cement slurry and pointed in white cement to match over and including 20mm thick screed bed in CM (1:4) laid over complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm (+2mm) thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Coloured glazed ceramic tiles (450X300 mm)X7mm thick as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed.

Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises complete all as specified and directed.

M&L Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over and including 15mm thick screeed bed or bedding layer in CM (1:4), in complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes icluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm. complete all as specified and directed.

M&L for reinforcement cement concrete (Normal mix )1:2:4 Type B1 (20mm graded aggregate) as in slab support on wall , beams and collums in floor roof landing balconies deck slab and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor and roof beams, lintels beam, cantilevers ,shelves including supports ,overhangs and similar work , for rough finished flat surfaces complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections complete all as specified and directed.

M&L for site Clearance in soft/loose soil complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed

M&L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded aggregate as in sub base, complete all as specified and directed.

M&L for surface excavation n exc 30 cm deep and avg 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed

Supply and fix electric water heater, storage type steel body anti rusted storage tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, PVC hot & cold water connection pipes, fastners etc. complete all as specified and directed.

S&F Steel water tubing, 15 mm bore, medium grade, galvanised with all fittings and fixed to walls and ceiling or laid in floors for providing water supply connection to the Geyser inlet and out let including extented connection to Kitchen complete concealed or surface run as per site requirement all as specified and directed.

S&F heavy duy PVC Tap of 15 mm dia including fittings such as socket, nipple, elbow complete all as specified and directed.

Supply & Fix LED bollard light 10 Watt, warm white, 2 feet long, single phase, 220 Volts made of ceramic body material, base plate type as per IS-10322 (part-5) mounted on PCC Square duly screwed complete all as specified and directed. Note :- Cost of PCC work 1:3:6 (20 mm) in square shape (.303x.303x.303 mtr ) for mounting of Lights included in the cost of item.

Supply and laying LT Cable & Supply, laying, Jointing connecting LT UG cable XLPE insulated,PVC bedded galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 6.0 sqmm 3.5 core laid in trenches/on poles/walls/in ducts/passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed.

All as per serial item No. 49 above but for 10 Sqmm 2 Core complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as apecified and directed.

Supply and laying well burnt sub class ‘B’ bricks. (designated 75) locally available best quality laid dry in trenches for protection of underground cable complete all as specified and directed.

Material and labour for GI tubing 25 mm dia light grade for passing through cables under the road, floor, along the wall or along the pole of the following dia complete all as specified and directed .

Supply and fix Supply and fix including commissioning of 16M high mast 360/150--3/3 shaft in two section suitable for 47 m/sec wind speed along with head frame, luminaires carriage suitable for 6-9 luminaires in symmetrical arrangement and other accessories manufactured in factory. Supply of raising lowering system comprising double drum winch, 4mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial and aviation light etc complete including all accessories complete all as specified and directed. (a) Supply and fix foundation bolts along with nuts, washers, anchor plate and common template. (b) Supply and fix LED type single dome aviation obstruction light.

Material and labour for construction of shallow foundation with concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour and including the erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour and Installation of the mast feeder pillar by grouting the stand in concrete complete all as specified and directed.

Supply and fixing LED flood light 120 watt 230 Volts, AC, outdoor type with thermal management in multiple optics and equipped with IP-66 protection, with impact and corrosion resistant complete with driver and lamp, all as specified and directed. (to be mounted on high mast pole).

Supply and fixing in repair of automatic street light control switch single phase 5-8 KW 40 Amps using infrared sensor based nature switch for automatic switching of street lights. Nature switch operation should be based on Natural light lux level. The sensor along with suitable power contactors and incoming out going MCBs should be enclosed pole/wall mounted thermo plastic polycarbonate enclosure conforming to IP 66 Protection Class 2 complete all as specified and directed.

Supply and laying LT Cable & Supply, laying, Jointing connecting LT UG cable XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16.0 sqmm 4 core laid in trenches/on poles/walls/in ducts/passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed. Note:- Earth work willbe measured and paid separately under relavant items of schedule

Supplying and laying reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x150mm x 40mm in trenches for protection of underground cable complete all as specified and directed.

Material and labour for GI tubing 40 mm dia light grade for passing through cables under the road, floor, along the wall or along the pole of the following dia complete all as specified and directed .

ANIL KUMAR AND CO (BID ID -3401962)