PROVIDING NEW HT SERVICE AND LT ELECTRICAL PANEL WITH ALL CABLE WORK FOR PERIYAR SHOPPING COMPLEX AT MADURAI CITY MUNICIPAL CORPORATION

Amount

11 KV, 25 KA, 630 A, HT Outdoor Three Panel Ring Main Gear complete as per specification

Supply of 1600 KVA 11 KV/433 KV (Oil filled type) low loss type, outdoor Power Transformer, DELTA/STAR (DYn11) with all the accessories, equipment along with OLTC, RTCC panel and connected Accessories as per the detailed specification. Transformer Protection relays should be provided at each Transformer such as Transformer Buchholz relay, restricted earth fault relay, OLTC surge relay, winding temp relay, Auxiliary relays as per standards.

Supply of 1000 KVA 11 KV/433 KV (Oil filled type) low loss type, outdoor Power Transformer, DELTA/STAR (DYn11) with all the accessories, equipment along with OLTC, RTCC panel and connected Accessories as per the detailed specification. Transformer Protection relays should be provided at each Transformer such as Transformer Buchholz relay, restricted earth fault relay, OLTC surge relay, winding temp relay, Auxiliary relays as per standards.

11 KV, 2 pole structure

Supply and laying of 11KV 3 core 300 sq.mm XLPE HT UG cable in a trench to be excavated at 1.0 Mtr. and covering the cables completely with RCC. Truff and refilling the earth to make good. From 3Panel VCB to Transformer

Supply and providing cable end termination suitable for 11KV 3 core 300 sq.mm XLPE HTUG cable with necessary outdoor type heat / cold shrinkable joint kit and accessories (Make : Ray Chem. / M Seal)

Supply and erection of Indoor cable end termination suitable for 11KV 3 core 300 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shrinkable joint kit and accessories (Make : Ray Chem. / M Seal).

supply and fixing of 10 core 2.5 Sqmm copper cable on wall with MS clamps

1010 KVA DG Set Supply of 808 kW / 1010 kVA, Diesel Generating Set comprising of: “Cummins” or any other eqvalant make approved by Chief engineer of Madurai Corporation, Radiator Cooled, Diesel engine developing 1180 BHP at 1500 RPM, complete with standard accessories, coupled to “Stamford” Alternator rated at 808 kW / 1010 kVA at 415 Volts, mounted on Channel Iron Base Frame complete Iron Base Frame complete with Fuel Tank of 990 Ltrs capacity with Manual Control Panel with PS602 controller and 02 number 12 V Batteries With acoustic enclosure

Supply and fixing of 1600A 4Pole ACB with enclosure with one set of spreader terminals and Operating handle with necessary cable top up box,including 50mm x6mm copper flat interconnection between the Raising main bus-bar to 1600A 4P MCCB terminal complete earth connection etc. (Make. L&T/ Siemens or Equiv)

ERECTION AND TESTING AND COMMISSIONING Erection of 1010 KVA Generator set with suitable foundation Pedestal height 5 ft with proper alignment of Genset including crane charges.

Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulations

BUS DUCT FOR 1000 KVA DG Supply and erection of 1600A, 415volts, 50KA, TPN aluminium Bus duct, indoor / outdoor type, dust and vermin proof. The bus duct with suitable flange at ends to connect with Transformer & Main MV Panel. Including Straight Run and 90 deg bend etc. as per site condition 2Runs 50x6 mm Aluminium earth bus shall be provided at both sides of the bus duct & to be painted with green enamel paint . Bus bar Size: 2R x 75 x 6 mm Aluminium Flat / Phase 1R x 75 x 6 mm Aluminium Flat / Neutral

1600A TPN Aluminium laminated flexible Joint with necessary hardware's

BUS DUCT FOR 1600 KVA & 1000 KVA TRANSFORMER Supply and erection of 1000KVA & 1600 KVA, 415volts, 50KA, TPN aluminium Bus duct, indoor / outdoor type, dust and vermin proof. The bus duct with suitable flange at ends to connect with Transformer & Main MV Panel. Including Straight Run and 90 deg bend etc. as per site condition 2Runs 50x6 mm Aluminium earth bus shall be provided at both sides of the bus duct & to be painted with green enamel paint. Bus bar Size (1600 KVA) 2R x 100 x 12 mm Aluminium Flat / Phase 1R x 100 x12 mm Aluminium Flat / Neutral

BUS DUCT FOR 1600 KVA & 1000 KVA TRANSFORMER Supply and erection of 1000KVA & 1600 KVA, 415volts, 50KA, TPN aluminium Bus duct, indoor / outdoor type, dust and vermin proof. The bus duct with suitable flange at ends to connect with Transformer & Main MV Panel. Including Straight Run and 90 deg bend etc. as per site condition 2Runs 50x6 mm Aluminium earth bus shall be provided at both sides of the bus duct & to be painted with green enamel paint. Bus bar Size (1000 KVA) 3R x 100 x 6 mm Aluminium Flat / Phase 2R x 100 x 6 mm Aluminium Flat / Phase 2500A & 1600A TPN Aluminium laminated flexible Joint with necessary hardware's

100 x 12 mm Aluminium flexible joint

100 x 6 mm Aluminium flexible joint

MV PANEL Design, Manufacturer, supply, testing and commissioning of 2500A floor mounted MV cubical panel bus bar chamber dust and vermin proof accommodating the following switches and 1nos 2500A ACB as Incomer units with the following items of work complete to satisfy the latest IS rules and CEIG guidelines. (For detailed description for this item plz refer Page no.92 & 93 in tender document)

APFC Panel Design, manufacture, testing at works, supply and delivery at site of Auto Power factor correction Panel(APFCP) suitable for 415Volts 3Phase 4wiresystem, fabricated from 14/16SWG CRCA sheet steel, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, complete with internal wiring, ferrules, name plates, painting etc., conforming to the technical specification for panels& comprising of the following. (For detailed description for this item plz refer Page no.94 in tender document)

SUB SWITCH BOARD PANEL Supply and Erection of 800A capacity dust and vermin proof cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting fuse switch with HRC fuse arrangement in five vertical rows Two for switches with a bus bar chamber and cable chamber and cable alloy confirming to IE rules INCOMER 800A 3 Pole MCCB -1No OUTGOING 1) 250 A TP MCCB-1 Nos 2)200A TP MCCB - 8 Nos (All the MCCB's should be Siemens/L&T) The Suitable 800 A bus bar should be provided with tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel; of earth bus. The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly

Supply and Erection of 630A capacity dust and vermin proof cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting fuse switch with HRC fuse arrangement in five vertical rows Two for switches with a bus bar chamber and cable chamber and cable alloy confirming to IE rules INCOMER 630A 3 Pole MCCB -1No OUTGOING 1) 250 A TP MCCB-3 Nos 2)125A TP MCCB - 4 Nos 3)63A TP MCCB - 7 Nos (All the MCCB's should be Siemens/L&T) The Suitable 630 A bus bar should be provided with tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel; of earth bus. The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly

Supply and Erection of 250A capacity dust and vermin proof cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting fuse switch with HRC fuse arrangement in five vertical rows Two for switches with a bus bar chamber and cable chamber and cable alloy confirming to IE rules INCOMER 250A 3 Pole MCCB -1No OUTGOING : 1)63A TP MCCB - 7Nos (All the MCCB's should be Siemens/L&T) The Suitable 250 A bus bar should be provided with tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel; of earth bus. The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly

Supply and Erection of 200A capacity dust and vermin proof cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting fuse switch with HRC fuse arrangement in five vertical rows Two for switches with a bus bar chamber and cable chamber and cable alloy confirming to IE rules INCOMER 200A 3 Pole MCCB -1No OUTGOING 1) 125A TPN MCCB - 1Nos 2) 63A TP MCCB - 7Nos (All the MCCB's should be Siemens/L&T) The Suitable 200 A bus bar should be provided with tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel; of earth bus. The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly

Supply and fixing of 7 Segement three phase distribution board with 6 way triple pole MCB distribution board with Metal Door cover with IP42 Protection, with 63A 4 pole MCB as incoming and 3Nos 40A DPMCB and 18Nos 10A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Like Legrand/Hager L&T make) (MLDB)

AHU Panel - 6 WAY INCOMER 1 Nos 125A TPN MCCB OUTGOING 6 Nos 32A TP&N MCB

AHU Panel - 12 WAY INCOMER 1 Nos 32A TPN MCCB OUTGOING 12 Nos 63A TP&N MCB

Supply and Erection of 63A MCB Isolator with 4 pole MCB Enclosure

A.Supply, laying, testing & commissioning of the following sizes of 1.1KV grade Aluminium / Copper Conductor armoured power cables on trays, ceilings, walls trenches, ground etc., with necessary clamps, cable ties, fasteners, identification tags, cable marking as required. Supply and clamping of 3 ½x400 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 3 ½x300 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 3 ½x185 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 3 ½x150 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 3 ½x50 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 3 ½x25 sqmm PVC armoured LTUG cable on wall with earth connection

Supply and clamping of 4 X 16 sqmm PVC armoured LTUG cable on wall with earth connection

B.Supply & end termination of following AL/CU armoured power cables with necessary Single compression brass glands, AL/CU. terminal sockets, insulation tapes, fasteners, earthing clips & connecting the clip to main earth bus with suitable bare copper wire complete accessories as required Supply and providing cable end termination of 31/2 X 400 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 300 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 185 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 150 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 50 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 25 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 31/2 X 16 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete

C.Supply & erectionof gland of following AL/CU armoured power cables with necessary Single compression brass glands, AL/CU. terminal sockets, insulation tapes, fasteners, earthing clips & connecting the clip to main earth bus with suitable bare copper wire complete accessories as required Supply and fixing of brass cable gland for 3 1/2 x 400 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 x 300 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 x 185 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 x 150 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 x 50 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 x 25 sqmm PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 4 x 16 sqmm PVC armoured LTUG cable with earth connection

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray - 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray - 300 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray - 450 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer", "Bends", "Tee", "cross member" - 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer", "Bends", "Tee", "cross member" - 300 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer", "Bends", "Tee", "cross member" - 450 mm width X 62.5 mm depth X 2.0 mm thickness

Equipment earthing Provision of Plate Earthing on with an earth electrode of 2.1mtr class ‘B” GI pipe of dia not less than 40mm with copper earth plate of size 2ft x 2 ft 3mm thickness with necessary funnelling arrangement with necessary masonry work with 38 mm RCC cover slab for brick masonry works.

Earthing as per ISI specification with an earth electrode of 2.1mtr class ‘B” GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mmx6mm with necessary funneling arrangement with necessary masonry work with 38 mm RCC cover slab for brick masonry works.

Supply & laying of following size Copper Flats & Wires. 100 x 6 mm Copper flat for TR. Neutral Earth

50 x 6mm Copper flat for 1000 KVA DG. Neutral Earth

25 x 3mm Copper flat for TR, DG, MV Panel Body Earth -76

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/support on wall / floor/ground for earth connection

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps/support on wall / floor/ground for earth connection

Supply and run of No 8 copper in PVC pipe for earth connection

Lightning Protection Supply & installation of 5spronged lightning conductor with suitable base etc.

Supply and laying of 1 runs single core 70 sqmm copper flexible cable with 32mm dia UPVC pipe and with all accessories including with necessary clamps & screws, bend etc. (Necessary scaffolding/ladder arrangement for laying of PVC pipe arranged by you)

Safety Accessories for below all accesrioes AC Chargeable Emergency Lamp 2 x 11W PL Lamp with all connected accessories 2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS First Aid Box complete with all First Aid Medicines Shock Treatment Chart fixed in glass frame 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle Hand Gloves 11KV Grade Danger Board as required by the Electrical Authorities Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

ESCALATOR1 (From Ground floor to Basement floor) with following specification - Model -Link india of OTIS or equivalent, Floors served - Ground Floor to Basement floor, Arrangement - side by side, Environment - Indoor, Rise 5.2 mts., Inclination degree-35 deg., Speed MPS 0.5. Handling capacity-6750, step Width in mm -800, No.of flat steps-2 flat steps, Actual lingth in mm-11933, Cost provision for All Electrical Works, All steel items like Bearing plate, Escalator Outer cladding, scaffolding & Minor Building Works. Cost of Contingencies, Miscelleneous and approval expenses with 3 years free maintanence

Add GST 18%

Schnell Energy Equipments Pvt Ltd