SPECIAL REPAIR TO TOILETS OF BLDG NO P-04, P-05 and P-06 AT LGJ MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engineer-in-Charge

M&Lglazed ceramic coloured tiles 450x300x7mm thick joint less as in skirting/dado etc set and joined in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L rendering 10 mm thick on brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall, finished even and fair including mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge. Note : - (WPC shall be measured and paid seperately)

M&L Rendering 5mm thick on brick work or concrete surfaces in cement mortar 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for 3 coats of white wash on newly surfaces on ceiling incl preparation etc.complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of cement base paint on new/old plastered surfaces incl preparation etc complete all as specified & directed by Engr-in-charge.

Dismantling of brick tiles in floor laid dry and pointed in cement mortar complete all as specified & directed by Engr-in-charge.

Demolition mud in roof, any thickness, including plastering and leeping complete all as specified & directed by Engr-in-charge.

Supply only integral water proofing compound complete all as specified and directed by Engineer-in-Charge. Make Dr Fixit/Fosroc/BASE/STP

M&L for Roof treatment to RCC roof as follows:- (a) Cleaning the roof surfaces thoroughly using wire brusehes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/plaster etc. (b) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Providing one coat of approved bituminous primer @100 gms per sqm, over dried plastered surface. (d) Laying 3 mm thick APP membrane,(mineral finish) reinforced with non woven polyster fabric, by torch application. The overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by E-in-Charge. Make : STP Dr Fixit/Pidilite, Texsa India Ltd/Tikitar Dansona/Bengal Bitumen Notes : (i) All joints and change in directions should be covered wih cement mortar (1:3) mixed with SBR latex @ 200 ml/bag of cement/as per site reqmt and cured well before laying membrane by torching. (ii) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. The name of firm shall be got approved from GE before carrying out the wk. (iv) The independent testing of membrane for technical parameters given in particular specifications shall be carried out from Govt approved labs having fascilities for testing of membrane. (v) The guarnatee of treatment shall be for min 10 yrs reckoned from date of completion of whole wk.

M & L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc. complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkhats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge

S&F powder coated aluminium frame/shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by Engr-in-Charge. Make of Al Section : Jindal / Hindalco / NALCO

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) in each window shutterand necessary accessary as required complete all as specified and directected by Engr-in-Charge. Note : Glass will measured and paid separately. Make of Al Section : Jindal / Hindalco / NALCO

M&L 4.8 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engineer-in-Charge.

S&F powder coated standard aluminium anodised grill size of mesh 75mmx75mm and 8mm thick section using U channel 25x12mm complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood , plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebaed and prepared to receive glass guaze, etc (without sash bars), edges of framing plain, charmfered or rounded fitted with cut and mitred beads for securing glass, etc size of me-mbers of shutters as specified in SSR PartI, section8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engineer-in-Charge

S&F 150 mm long extruded aluminium allloy handle, fabricated type anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 300mm long,aluminium alloy anodised sliding door bolts type not less than 16mm dia fixed complete all as specified & directed by Engineer-in- charge.

Supply and fixing 300mm ordinary rat tail rod pattern spring including roller and roller plate complete mild steel fixed complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S & F 150mm long floor door stopper of aluminium alloy body and tongue,anodised with hard drawn steel spring complete all as specified & directed by Enginee-in-Charge

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge

S&F drapery rods, coloured, standrad quality powder coated not less than 25mm dia with heads at both ends and middle support rings etc complete all as specified & directed by Enginee-in-Charge

S&F in repair PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engineer-in-Charge

S&F in repair bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified and as directed by Engineer-in- charge Note :- The minimum weight of tap shall be as given in SSR or in relevant IS.

S&F in repair tubular towel rail, brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in- charge.

S&F ISI marked rotational moulded polyethylene water storage tanks 500 ltrs capacity of double layer vertical with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer-in-Charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair complete all as specified and directed by Engineer-in-Charge

S&F in repair ball valves hight pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed in 20 mm dia bore pipe, (Minimum weight 20 mm-210 gms) complete all as specified and directed by Engineer-in-Charge

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified and directed by Engineer-in-Charge

,-- ditto-- all as per serial item No 39 above but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as specified and directed by Engineer-in- charge.

,-- ditto-- all as per serial item No 41 above but for fixing only complete all as specified and directed by Engineer-in-Charge

,-- ditto-- all as per serial item No 41 above but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as in roof padding and laid in slop 1:30 complete all as specified and as directed by Engineer-in-Charge.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm as on roof including cleaning of surfaces complete all as specified and directed by Engineer-in-Charge

M&L APP based membrance minimum weighing 3KG per sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torced application with APP membrane ove a coat of Aluminium paint over 10mm thick screed bed in CM 1:3 mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge

M & L PCC 1:2:4 type B-1, using (20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L PCC (1:7:12) using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified and directed by Engineer-in-Charge.

M&L for creating fillet caving 50 x 50 mm with polymer modified morter on the junction of slab and wall as per manufacture instruction, Material and labour Providing for applying two coats of two component (1 part Liquid : 2 part Powder) ready to use cementitious waterproof coating on properly prepared surface by brush having eleongation of >50% for applying water profing treatment as per following and complete all as specified and directed by Engineer-in-Charge. Applying water proofing treatment as fallowes :- (a) Applying 1st coat of two omponents modified polymer coating on horizontal and verticle surfaces. (b) Provn of glasses fiber mess of 2 x 2mm immediately on alone coating. (c) Appalying 2nd coat of two omponents modified polymer coating after 72 hrs on horizontal and verticle surfaces. Note :- Complete treatment to be carried out by authorised applicatior of waterproofing manufacture. Make : Dr Fixit/ Fosroc/ BASF/STP

M&L for brickwork with fly ash old size bricks, straigth of curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge

M&L for brickwork with fly ash old size bricks, straigth of curved on plan any radius half bricks thick walls, built in CM 1:4 complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1.00 sqm but n. exc 2.00 sqm each including removing to store complete all as specified and directed by Engineer-in-Charge

S&F in repair 4mm thick pin headed glass and glazing with via putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed by Engineer-in-Charge

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames,complete all as specified and as directed by Engineer-in- charge.

S&F framed work as in chowkhats of doors window of angle iron, gates or other section withh gusset plates, rails braces etc conforming to Gde Fe 410-0 or Fe 310-0 complete (Quality-A) complete all as specified and as directed by Engineer-in- charge.

S&F hold fast iron conforming to Fe-290 or Fe 330 including preparing the surface & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified and as directed by Engineer-in- charge.

S&F in repair stainless steel wire cloth 0.63 nominal dia of wire and average width of apertune 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge

Supply & fixing, 2nd class hard wood (Sal) or any other 2nd class hard wood articles not exceeding 200 cubic centimetre each as small fittings such as shaped door and window stops and the like, including necessary labour etc complete all as specified and as directed by Engineer-in- charge.

Taking down steel window of area n.exc 1.50 sqm and refixing in same opening after necessary repairs and provn of box type hinge in lieu of projective type hinges and MS tower bolt of 150mm incl welding, revetting etc complete all as specified and as directed by Engineer-in- charge.

M&L for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 02 Nos MS 100mm size barrel tower bolt for each leaf and Z section handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

S&F steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified and as directed by Engineer-in-Charge.

M&L 20 mm thick granite of approved colour as in shelves/partition rubbed and polished, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding the edges half round on exposed side over and including 20 mm thick screed base in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L Rendering 15mm thick on brick walls or concrete surfaces in cement mortar 1:6 and surface to be finished even smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparing newly plastered or pointed surface of wall and applying 3 coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

Material and labour of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in- charge.

Material and labour preparation of old painted steel surfaces of any description not otherwise described over 10 cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed by Engineer-in- charge.

Material and labour preparation of old painted wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed by Engineer-in- charge.

Supply & fixing, 4mm thick pin headed glass and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

Hacking out old broken glass (any thickness, size or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed by the Engineer-in-Charge.

Taking down eaves gutters and rain water pipes ( any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 110mm bore UPVC pipes single socketed in any length with rubber ring joints fixed to wall including necessary clamps complete all as specified & directed by Engineer-in- charge.

S&F 450mm long mild steel GI pipe, medium grade of size 40mm dia as in spouts pipe in sunken floor including making holes in RCC and making good with CM 1:1 or PCC (1:2:4) complete all as specified & directed by Engineer-in- charge. Make Tata/Zenith/Jindal

S&F UPVC bend 110mm bore complete all as specified & directed by Engineer-in- charge.

S&F 100mm bore cast iron hubless pipe waste and vent pipe in any length with or without ears laid in trenches/floor/wall including clamps jointing with necessary coupling complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F in repairs cast iron type hubless P trap/CPWD floor trap 100mm bore with CP grating including jointing to waste pipe fixed with necessary coupling arrangement complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F in repair 100mm bore cast iron hubless type door T equal/unequal branch piece (any radius) diminishing pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified & directed by Engineer-in- charge. Make NECO

S&F in repair 100mm bore cast iron hubless type plain bends (any radius) dimining pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified & directed by Engineer-in- charge. Make : NECO

Supply only 100mm bore sheilding (ss) coupling with EPDM rubber as per requirement complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F 75mm bore cast iron hubless pipe waste and vent pipe in any length with or without ears laid in trenches/floor/wall including clamps jointing with necessary coupling complete all as specified & directed by Engineer-in- charge.

S&F in repairs cast iron type hubless P trap/CPWD floor trap 75mm bore with CP grating including jointing to waste pipe fixed with necessary coupling arrangement complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F in repair 75mm bore cast iron hubless type door T equal/unequal branch piece (any radius) diminishing pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F in repair 75mm bore cast iron hubless type plain bends (any radius) dimining pieces or tapers (larger bore measured) door fixed with necessary coupling complete all as specified & directed by Engineer-in- charge. Make : NECO

Supply only 75mm bore sheilding (ss) coupling with epdm rubber as per requirement complete all as specified & directed by Engineer-in- charge. Make : NECO

S&F Clamp for hanging/fixed of 75mm/100mm hubless pipes complete all as specified & directed by Engineer-in- charge.

S&F as in repair 15mm dia Stop valve, cast copper alloy with crutch of butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed by Engineer-in- charge.

S&F vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rests (excl flushing cistern) but including CI 'P' trap set in and including concrete fixed complete all as specified & directed by Engineer-in- charge.

S&F in repir Vitereous china urinal flat back of size 465x355x265mm white with grating & Union for discharge pipe including spreader of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60grms) but excluding flushing cistern, flush pipe & waste pipe but fixing only automatic flushing cistern with bracket flush pipe etc complete all as specified and as directed by Engineer-in-Charge. Make : Parryware Cat No 600001 or equivalent

Supply & fixing in repair vitreous china wash hand basin, coloured,counter top (bowl type/oval shape) of size 560 x 450mm long screwed shank fly nut flange end including cutting for and pinning in in ends of brackets in 1:3CM including 32mm dia chromium plated waste coupling/trap complete all as specified and as directed by Engineer-in-Charge.

S&F grating doom CP 100mm dia of plated with waste hole complete all as specified and as directed by Engineer-in-Charge.

S&F 32mm PVC waste down pipe suitable for WHB and urinal complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed by Engineer-in-Charge. Weight not less than 450 gms

S&F PVC connections 15mm size with PTMT nuts of length 600mm long complete all as specified and directed by Engineer-in-Charge

Supply & fixing in repairs PTMT swivel shower roses 125mm with or without swivel joints, including fixing to steel pipe or union fixed complete all as specified and directed by Engineer-in-Charge.

Dismantling/demolition exc 250 but n.exc 500 litre capacity any type of water tank and remove from site complete all as specified and directed by Engineer-in-Charge.

S&F ISI marked rotational moulded polyethylene water storage tanks 1000 ltrs capacity of double layer polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 0.71 mm thik plain aluminium sheeting alloy 31000 H4 as in covering of expantion joint stappeled with self taping screws including dismantling of old any type of sheet complete all as specified & directed by Engineer-in- charge.

E/M Portion Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for concealed point wiring with single core PVC insulated, unsheathed multistranded copper conductor cable of size 1.5 Sqmm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 Sqmm (FRLS) including MS shunk sheet metal box with 3 mm thick hylam sheet top cover of required size for mounting switches, sockets etc complete for One Light point controlled by one, one way switch complete all as specified and directed by Engineer-in-Charge Note - Quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour.

,--- ditto-- all as per serial item No 103 above but for one ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engineer-in-Charge.

,--- ditto--- all as per serial item No 103 above but for one 3 pin switch socket outlet, 5 Amp on the same board with other switches complete all as specified and directed by Engineer-in-Charge.

,--- ditto--- all as per serial item No 103 above but for one 3pin 5 Amp switch socket outlet on the independent board complete all as specified and directed by Engineer-in-Charge.

,--- ditto--- all as per serial item No 103 above but wiring with 4 Sqmm multistranded cable and earth wire with copper conductor of size 4 Sqmm for 15 Amps power point complete all as specified and directed by Engineer-in-Charge.

Supply and fixing piano switch flush button single pole one way 5 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing socket 2 in 1, 2/3 pin 5Amp flush type 240 Volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fixing socket 2 in 1, 3 pin 5 Amp and 15 amp flush type 240 Volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fixing piano switch 15 Amp flush type 240 Volts AC complete all as specified and directed by Engineer-in-Charge.

S&F LED light fitting 1 X 18/20 W, 230 V integral sleek polycarbonate LED channel with white acrylic cover including making connection complete all as specified and directed by Engineer-in-charge.

S&F lamp holder insulated body with back plate for angle /batten fitting with LED of 9 watt lamp complete all as specified and directed by Engineer in charge.

S&F ceiling rose surface bakelite two or three terminals / plate 5 Amps complete all as specified and directed by Engineer in charge.

S&F sheet metal enclosure DB single pole and neutral for 240 Volt 8 way with 200 Amps rated busbar flush/surface mounting double door concealed in wall complete all as specified and directed by Engineer-in-Charge.

S&F MCB single pole 240 volt 5-32 Amp 10 KA B Curve complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SPN 240 Volt 40 Amps 10 KA B Curve complete all as specified and directed by Engineer-in-Charge.

M & L forEarthing complete with galvanised steel earth plate electrode 600mmx600mmx6 mm buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, earth plate surrounded by 15 cm thick and pack layer of charcoal dust and common salt, connected to earth lead of GI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15 mm dia and water pipe 20 mm dia GI light grade with funnel and wire mesh, PCC chamber in cement concrete in(1:2:4) type B-1 and CI cover with frame all as shown in Electrical Plate No - 3 of SSR-2009 (Part-I). Note : (i) 20 mm GI pipe for watering to be provided with a socket and plug and should be 10 cm above ground level (ii) Outer edge of earth plate will be 1 m away from the outer edge of PCC chamber (iii) GI wire upto DBs earth connections is included in this item (iv) Water pipe shall be provided in slanting position

Supply and fixing LED building security light fitting 25 Watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover and accessories complete incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer after taking down old u/s one complete all as specified and directed by Engineer-in-Charge.

S&F fresh air fan 300mm sweep 240 volt 50Hz plastic body complete with louvers complete all as specified and directed by Engineer-in-Charge.

S&F mirror light with high output, diffuser for glare free LED 7 watt light complete all as specified and directed by Engineer-in-Charge

S&F exhaust fan 450mm sweep 410 watt, 1400RPM, 6800CMH, double bearing louvers, single phase 230 volts 50Hz including grouting with fasteners, nut/bolts etc complete all as specified and directed by Engineer-in-Charge.

S&F factory made, sheet distribution board DB SPN 8 way double door with 200 amps rated bus bar complete all as specified and directed by Engineer-in-Charge

S&F MCB SPN 32 Amps B Curve in SPN DB 8 way complete all as specified and directed by Engineer-in-Charge

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps SP for geyser supply complete all as specified and directed by Engineer-in-Charge

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

PAREEK AND COMPANY