Interior works

Amount

Designing, providing, and fixing 4mm thick approved make and shade Aluminium Composite Panel (Durabuild/Eurobond or approved make) cladding, and canopy at different locations and full height of the building including soffits of over-hangs and including MS brackets / Aluminium alloy brackets, sections with grids filled in with weather silicon sealant (Dowsil or approved equivalent) as per the drawings. The Panel composition shall be 0.5 mm thick PVDF coated aluminum sheet + 3mm thick low-density polyethylene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminum sheet. The rates are including labour, tools & tackles, scaffolding, etc. all complete as per approved shop drawings and specifications and as directed by the Engineer-in-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary scaffolding, filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, including scaffloding all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing the charcoal wall Panelling/cladding with following models MRL-175, MRL-191, MRL-412 or approved equivalent. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both diretions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws will be fixed over the plywood using adhesive and finishing the rate inclusive of conveyance to site and labour charges and as directed by the Engineer in charge. The design shall be got approved by the Engineer in charge concerned before use on work etc., complete. Note : The plywood and aluminium section will be paid separately through relevant items.

Providing and fixing 19mm thick BWR waterproof plywood for partitation, Wall paneling, tble and wardrope shutters door etc. with necessary edge tape screws, nails etc as per the direction of Engineer in charge.

Providing and fixing 12mm thick BWR waterproof plywood for partitation, Wall paneling, tble and wardrope shutters door etc. with necessary edge tape screws, nails etc as per the direction of Engineer in charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (a) 1.0 mm thick

Supply and fixing of Powder coated steel door frame with approved size & colour with single /double leaf shutters at all level with 2 hours fire rating with vision panel size 200X300 mm (The glass shall be Saint-Gobain brand or approved equivalent). Including all necessary approved hardware fittings like SS ball bearing hinges, ss tower bolt, SS pull handle “D” type 22X300 mm with extended spindle , 278 dead lock with 70mm EPC , TS 71door closures, Anchor fasteners, suitable gasket/ tape / sealant in gape between glass and shutters, frame and wall, etc., including labour, tools and tackles & transportation etc and all complete as per drawing and as directed by the Engineer in charge. Note : 1) Outer to outer Dimension of DOOR size will be measured for payment 2) Fire proof system certification shall be submitted.

Providing and fixing false ceiling with 12.5mm thick tapered edge gypsum moisture resistant board at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm or both sides of joint and including the cost of painting one coat primer and two coats of emulsion paint of approved colour, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and applying painting Two coats at all levels with premium Plastic emulsion paint (Asian or Equivalent approved brand, colour and manufacturer) to give an even shade including one under coat of cement primer, applying putty, preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge.

DHATHATHIRI AND CO

KANNIAPPA ELECTRICALS