Signalling work for strengthening of Signalling infrastructure in LKO-SLN-ZBD section of Lucknow Division of Northern Railway in view of upcoming Inspection.

Description:- Excavating and refilling of trench to the level of ground with rammed earth asper

the station along side the track. It shall confirm to the safe distance as per signalling and cable plan in all type of soil, it also includes clearence of roots of trees and bushes.

Description:- Laying of signalling/Telecom/power cables of different sizes as per attached guidelines (Drg. No.(NR/S&T/Con/1.1/97A) or latest on signalling cable laying and as per cable route

cable before and after its laying of all type of outdoor cables. Contractor have to transport cable from any store of LKO division to site carefully. Meggering to be done for each drum separately. Meggering sheets to be supplied and filled up by contractor and submitted to Railways, as per instructions by Consignee.

(NR/S&T/Con./1.1/97A) or latest and as per instruction of the site Engineer.

LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY

lubricated pipes as per RDSO Spec no. RDSO/SPN/204/2011 Ver 1.1 or latest of 120mm nominal dia in the bore at the depth of 1.4 meter to 2.1 meter from formation level (level of earth below ballast) as per drawing and as directed by Engineer Incharge by trenchless technology for laying of signalling /telecom/power cable under track /culvert etc. cable laying covered separately. Inspection-RITES for Supply of DWC/HDPE pipe. The following required coupling arrangement should also be supplied: 1. Suitable snap fit couplers withrubber O ring, 2. Spacers, 3. Tees. 4. Bend. 5. End Cap(1 no. =6mtr ,Straigh tpipe). (A) The cost shall include horizontal boring through any intermediate obstruction, either natural or man made or any boundary etc. (B) The rate is inclusive of all the materials equipment and labour required for during trenchless horizontal boring under the railway track. Nothing extra shall be admissible on any account than the rate quoted above. (C) The Pipeis to be laid underrailway track/road /culvert. All necessary arrangement are to be provideand all precautions are to be end is not deviated from the horizontal level line by more than 250mm in horizontal and vertical direction. (D) The rate shall be inclusive of direction and protection of underground utilities encountered during boring. (E) The payment for boring shall be made only when DWC/HDPE pipe are laid in the bore.

pull out tray, drawer and top made off MDF Model C-13. Make: Godrej or better. Inspection- Consignee

instruction of Engineer incharge. Inspection- Consignee

Description:- Supply of ESM furniture of Godrej or similar reputed make as per approval of engineer consisting of the following: 1. Executive revolving bearing series low back floating chair

lockers cabinet on other side : 1No. 3. Visitor chair seat & back cushion with high density Foam with plastic PVC handle capsul type Flat pipe duly Painted black : 3Nos.4. One Steel Almirah of size 48"x30"x17" with lock and handle arrangement for record keeping at station. Inspection : Consignee

similar Iron Clad switch. Inspection- Consignee

Description:- Casting, concreting, curing of foundations of size (400mmx300mm) at surface and 1000mm deep and erection of retroreflective SLB/BSLB/SB/ calling on boards/Goods Warning

includes supply of retroreflective SLB/BSLB/SB/ calling on boards/Goods Warning Board/Passanger Warning Board. The SLB/BSLB shall be as per approved Drg. No.SA-2373 or latest. Calling on board should be as per Drg NO: NR/S&T/D&D/01/2022 or latest. Inspection by : Consignee for supply portion

Description:- Fabrication, Supply and fixing of retroreflective P/G/C/ markers with complete fittings

sheet, MS angle. Nut and bolts, paint and painting materials will be supplied by the Contractor. The P and G markers shall be as per Drg. No. S 23456 (Adv) & SA 23477 (Adv) or latest respectively. Inspection : Consignee for supply portion.

and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

/Bourn/Fuzetech/Little Fuse or similar. Inspection by-Consignee

Description:- Shifting of Apparatus case Single: It includes the Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringment as instructed by the railway repsentative at site. The

for shifting/ turning the location boxes. Necessary masonary work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site, if the existing earth connection to the location boxes are disturbed the earth wires shall be the properly reconnected. (All materials required for the work shall be supplied by the contractor).

LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY Description:- Shifting of Apparatus case half: It includes the Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning 14 the location boxes to clear of the infringment as instructed by the railway repsentative at site. The work includes ensuring the safety of the signalling system, releasing the cables coils to give access for shifting/ turning the location boxes. Necessary masonary work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site, if the existing earth connection to the location boxes are disturbed the earth wires shall be the properly reconnected. (All materials required for the work shall be supplied by the contractor)

Description:- Cleaning, scrapping, painting & lettering of all newly installed & existing gears such as signals, point equipment, track circuit equipment with TC No. on rail, app. cases, JB, TLJB, point rodding, cranks, compensators etc. including gate equipment if existing in station section as per the

Nerolac or similar make. shall be approved by Railway Engr.and painting materials to be supplied by the contractor. This includes writing, and painting requirement of all indoor and outdoor gears along with marking of all circuit Nos. near terminal and terminal boards/rack in app.cases, Jn.boxes, relay room, SMs room, writing of relay nomenclature, fuse Nos. and equipment nomenclature as per the approved plans and as per provision of IRSEM.

Description:- Cleaning, scraping, painting and lettering of all newly installed and existing gears by the contractor for existing/new Level Crossing Gates.This includes supply of all painting materials

and fuse nos, relay and equipments nomenclatures as per approved terminal chart and provisions of SEM. All paints (ISI marked) with IS specification No. IS:15489:2004 Asian /Burger/Nerolac or similar make. shall be approved by Railway Engr.and painting materials to be supplied by the contractor.

Description:- Supply of 4 conductor dis-connect terminal block for test and measurement 0.8

carreir rail DIN 35 front entry cage clamp connection Grey wago or similar as RDSO/SPN/189/2004 Rev. 3.0 or latest. Material to be supplied from RDSO approved firm. Inspection : RDSO

Wago or similar as per RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection : Consignee

RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection : Consignee

similar as per RDSO/SPN/189/2004 Rev. 3.0 or latest. Inspection : Consignee

existing trench & laying the same in new trenches. Digging, Placing of capping/Half round RCC pipe covered separately.

Description:- Strengthening of foundations of signals, Full/Half location boxes up to a height of 30

work from bottom of earth work using country stones and cement masonry to prevent the earth from slipping down the bank.

Description:- Earth work for excavation and refilling around location boxes and signals etc. where

location to the centre of filling and lift from main ground level. The earth work should be well rammed including breaking of clods, levelling and dressing etc. as per instruction of Engineer at site.

(ordinary) mixture of 1:4 ratio. All material is to be supplied by the contractor. (Inspection: Engg representative.)

Description:- Concreting unschduled items in concrete of 1:3:6 ratio in cement, coarse sand and aggregate 25mm at different places in the yard and plastering top in fine plaster of 1:4 cement sand

incharge. The volume in cubic metres shall include the volume occupied by any CI foundation, trestle, MS angle or flat or GI pipe required to be embedded in the casting. Cement coarse sand and aggregate 25mm are to be supplied by the contractor.

LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY

levelling the formation, Dismantling any infringing structures, clearing and removing debris etc., with all lead and lifts etc., complete and as per the instruction of railway representative at site.

Description:- Maintenance of Main/Tail signal cable/ signalling gears and Gates. The work organise by team is Main signal cable test in disconnection, Tail signal cable test in disconnection/

Black Smith-1 no, Fitter-1 no and helper-4 nos. It also includes any work of signalling gears. Any other work as per instruction of railway Engineer. All T&P required to execute the work will be supplied by the contractor. unit days means team per day.

(Red/Black/Green) as per IS: 694/2010 or latest, as per Specification No. IRS:S-76/89 or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO

(Red/Black/Green) as per IS:694/2010 or latest, as per Specification No. IRS:S-76/89 or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO

(Red/Black/Green) as perIS:694/2010 or latest, as per Specification No. IRS:S-76/89 or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection- RDSO

Description:- Supply of wiring materials asper IS Spec. No. 2465/1984 with latest Amend. and

ofstrand-85 & diameter of strand-0.30 mm + - 0.00, insulation thickness 0.80 mm Normal conductor Resistance 3.30Ohm/Km (RED & BLACK colour50% each) Material to be procure from RDSO approved firm. Test parameters are as per(IRS)/76/89(Amdnt.3). Inspection : Consignee

new maintenace free earth. (Cad weld or similar). Inspection- RDSO

Description:- Supply and installation of earth electrodes as per std.practice. The item includes digging of pitin earth, 3 Mtrs. deepand fixing earth electrode pipe.Casting of cement concrete enclosures as per drg. No.(NR/S&T/CON/6.4/97) or latest. The soil treatment shall be done as per std.practice. The item includes provision of mild steel flat of size35mm x 6mm (as per IRSEM) and

connected to block instrument,cable sheath of power equipment, signal base, apparatus case, CT rack / relay racks, other equipments as per the instruction of Engr. at site & IRSEM. Earth connection Signal & location boxes to be done Drg.No. 19-D6 of IRSEM App II or latest. Complete materials such as earth electrodes as per Drg. No. (NR/S&T/CON/6.3/97)or latest, cement, wiring material, nutbolt for connection & mild steel flat of size minimum 35mm x6mm or 210 sqm as per SEM etc. to be supplied by the contractor. Inspection by - Consignee for supply of earth electrode.

material conforming to RDSO/SPN/151/97 or latest) complete with 450 mmlong 25 mm dia pipe. Inspection-Consignee

Description:- Fixing of track lead junction box (TLJB) due to repositioning of old TC as per Drg. No. NR/S&T/CON/3.2/97. This also include erection of track lead junction box & terminating the cable.

mixture of 1:3:6 ratio. This includes excavating ramming , curing and plastering of foundation with mixture of 1:4 ratio. Cement , sand , aggregate Iron angle , nuts & bolts are t be supplied by the contractor.

Description:- Preparation of Panel Diagram, location diagrams, power diagrams, cable plan, bonding plan etc in Auto Cad. The drawings shall be prepared in A3/A2/U size as required by Railways. The hard copies of the documents will be supplied by Railways. The Contractor has to draw

checked and returned by Railways indicating corrections if any. The correction shave to be made and final copy submitted in A3/ A2/ U size as required by Railways along with the final soft copy in Pendrive. The hard copy given by Railways have to be returned back without any damage. The size of sheet given in the unit column is for the hard copy given by Railways. c. For preparation of soft copy from U size hard copy. (The Rate is for per Sheet)

37 LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY 37 Description:- Supply of Original Tracings of A-3 Size. NOTE:- For Drawings larger than A-3 Size, payment shall be made in multiples of A-3 Size. Inspection : Consignee

instruction of consignee. All the material to be transported carefully without damage. Contractor have to do proper stacking of material and prepare list of material.

RDSO Drawing No. SDO/RDSO/E&B/001. All the sundry materials to be supplied by the contractor.

Insulation plate- 01 No., Ferrules- 2 Nos. Washers- 4 Nos. (Material Nylon 66).as per RDSO spec IRS-

Insulation plate- 01 No. , Ferrules- 2 Nos. Washers- 4 Nos. material nylon 66 as per RDSO spec IRS-

Drg n. T-1.367, T-10368, T-10384 to IRS-23 and S-40 with latest amendment completed with nut bolts etc..The material should be procured from RDSO approved firm. Inspection by Consignee

latest . 2,T-10371/Alt.2 ,T-10368/Alt. and to IRS S-23 and S-40.Inspection by Consignee.

mm x 100 Mtr rolls conspicuity marking tape (Yellow & Red) as per instruction of consignee. Inspection : Consignee

Description:- Wiring of relays in relay room/relay huts as per approved wiring diagrams. All material required will be supplied by contractor including indoor cables and wires of 1x1, 1x0.6,

latest IRS S76/89 (Amd.3) or latest available specifications . This also includes soldering, dressing, bunching, lacing, fixing of relay bases etc. and provision of LED indication box of vital relays in relay room if required and provision of potential free contacts of all relays on tag block for data logger as per instruction of site Engineer.

Description:- Supply of complete set of point rodding (Ground connection) for 220 mm stroke point

RDSO/S 11000, RDSO / S 3454 & RDSO/S-3395 or latest as applicable. (coal Bangal for smithy work, all type of nuts & bolts and Lugs as required also to be supplied with each set). (Inspection- Consignee)

Description:- Fabrication & Supply of complete set of point rodding for point machines of IRS type

bracket required (Coal & Smithy work), all type of nuts & bolts and Lugs as reqd. also to be supplied by contractor with each set) Inspection : Consignee

base. Inspection :Consignee.

Description:- Supply of Electrically Operated Lifting Barrier complete set suitable for 110VDC/24V DC (option to be specified in tender specifically of either 110 V DC or 24V DC) supply without hand generator back up & motorized boom locking arrangements as per RDSO Spec. SPN/208/2012 with latest amendment. One set consisting 02 Nos of Barriers of length 09.76 Mtrs. along with Spares &

shall be supplied alongwith each set (02 nos.) of Electric lifting barrier as per requirement of the purchaser i) GI boom - 1 no. complete. ii) Belt - 1 no. iii) Crank handle - 1 no. iv) Motor Contactor - 1 no. v) Motor protection MCB- 1 no. vi) Push button complete- 2 nos. vii) Limit switch - 3 nos. (1 lever type and 2 top roller type) viii) Fuses used - 2 sets 10.2 Tool kit consisting of standard sizes of wrinch/ spanner and Allen keys should also be supplied with each set (02 nos.) of Electric Lifting barrier. Inspection: RDSO

50 LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY 50 Description:- Installation, testing and commissioning of electrically operated lifting barrier, complete with Casting of cement concrete foundation for pedestal and boom rest post, cabling, power supply connection & wiring with complete outdoor work as per approved drawing, wiring etc.

Description:- Fixing in position and commissioning of sliding barrier boom set (1 set will consist of two sliding barrier booms, one for either side of track) this includes carrying out civil masonry work at site like digging of pits for foundations, casting of RCC foundations, fixing of foundation bolts and

includes loading, unloading and leading of all the material to site of work from the store of SSE Signal. Sliding barrier has to be made ready in complete working order as per instructions of Site engineer. Sliding gate, E type lock, T-2 lock and wiring materials will be supplied by the railways and all other material including cement, sand, aggregate (Ratio of cement, coarse sand and aggregate should be 1:3:6), nut bolt etc will be supplied by the contractor.

Description:- Fixing and wiring complete KLCR and its box in location boxes, supply, installation, wiring of heavy duty push button, LED indicator on MS sheet as per N.R. practice for crank handle

This includes all materials such as heavy duty push button, LED indicator (10mm), MS sheet of 4.5 mm thick, nuts and bolts, fixing materials for the magneto telephone, and wiring materials to be supplied by contractor. Inspection : Site Engineer

Description:- Supply of electric fuse complete with fuse block (base) for Railway signalling non

and fuse block made of PBT/Polycarbonate as per IRS:S-75/2006 (Rev.2 & Amd.2) and drg no. 23748 (IRS), Alt-4 or latest. Fuse block shall besuitable for round head type fuses. Inspection : RDSO for both Fuse and Fuse block

RDSO Specn.No.IRS:S 78/2006 or latest and Capacity 2/4/6/10A/16A/20A Amp. (material will be supplied only from approved vendors of RDSO) Inspection- RDSO

Description:- Supply & Installation of lightening & surge arrestors Indicative type of Class B & Class C suitable for single phase power supply in TT (Earth to earth) net work as per amdt 5 of RDSO Specification RDSO/ SPN/ 165/ 2012 (Ver.3) or latest & as recommended by RDSO vide letter No. STS/E/IPS/Genl dt. 27/1/2006. (RDSO Spec no.RDSO/TC/98/2011/Rev 0.0 ). Installation & commissionig of above Class B & Class C arrestors, These din rail mountable devices along with a 63 amp HRC fuse & fuse base shall be fixed in a wall mountable cabinet of minimumsize of 250mm (w) x 450mm (h) x 150mm (d). This box shall be made using Fire retardent fibre box/MS sheet steel of

the front door to asses the fuse. provision shall also be provided to view the working condition of class "C" arrestors from the front side of the cabinet. All the internal power wiring shall be made using aminimum of 10 sq mm pvc cable & termination shall be suitable for connecting 16 sq mm copper cable. The PF contact of Class C arrestor shall also be wired using aminimum cable of 2.5 sqmm & terminated on suitable terminal block. The Earth cable shall be connected to the equipottential bus bar using an insulated Cadmium bronze cable of 3/16 inch as per RDSO specification IRS-S:103-2004 using exothermic welding .All the material used for exothermic welding will be of RDSO approved/recommended make & all the tools & Tackles required shall be arranged by contractor only. Inspection : RDSO/RITES

PVC conduit pipe 1" dia, Inspection : Consignee

indoor cable laying as per instruction by Site Engineer

RDSO Specn.No.IRS:S-78/92 or latest and Capacity - 0.63 Amp. (material will be supplied only from approved vendors of RDSO). Inspection- RDSO

existing panel and as per site engineer. Inspection by consignee

Inspection- Consignee

61 LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY 61 Description:- Supply of seal plier as per sample got approved from site engineer incharge. Inspection- Consignee

mm made of half inches MS Plywood with as per std. practise of NR.

and as per site engineer. Inspection- Consignee

Description:- Installation, erection and wiring of 2/3/4 aspect LED lit colour light signal including 1/2/3/4/5/6 way Jn. type route indicator and stencil type/theater type route indictaor which also

bracket wiring the whole unit, focussing of signal and route indicator. Supply of unit Jn./stencil/Theater and off set bracket by contractor covered else where. All other wiring and fixing materials, 'U' bolt etc. will be supplied by the contractor.

Description:- Fixing, wiring, testing & adjustment of 143mm/220mm throw point machine complete as per standard practice. It also includes:- (i) Fixing of switch extension P bracket, providing insulation for switch extension bracket, fixing ground connections, adjusting the correct opening of switches and adjusting the point machine with crank handle.(ii) Wiring inside the point machine, erection of 30/40 line junction box as per Rly. drawing, provided with terminal strips for cable termination. (iii) Supply & Fixing of GI pipes with flange for taking cable in to point machine and Jn. Box through gland/ GI pipe.(iv) Complete material for insulation viz. point insulation material, junction box, GI Pipe/gland pipe, wiring material, nut & bolts of various sizes, angle iron of size

material for the stretcher bar 90R/52kg/60kg as per RDSO Drg. no. SA-23171 ( Adv.) Alt. 1, SA-

at site for complete installation of gauge tie plate and insulation of GTP as per Drg. No. NR/S&T/CON/7.6/97 and William stretcher bar ( if required) will be done by the contractor. Machine will be overhauled by the contractor if required. (vi) This includes removal of existing gears and fixing themachine at raised level on channel as per standard practice to avoid flooding wherever required. (vii) Supply of ground connection of electric point machine, Non insulated GTP and CTP extension plate, Junction box and stretcher bar shall be made available by the railways. Work at site shall be inspected by site engineer.

Description:- Installation and commissioning of SSDAC complete as per RDSO specification No.RDSO/SPN/176/2005(ver 2)/RDSO/SPN/177/2000 (ver2) or latest. The axle counter will be

protection track circuit. Installation to be done by OEM authorised Engineer as per the installation manual of the OEM. This include supply and installation of HDPE Pipe GI pipe shelded cable/wires masonary & wood work in location box relay room ASM Room it also include of fixing of resetting box in ASM office with all wooden and masonary work."

Block panel and UFSBI for Double line Operation as per Spec No. IRS: S 105/2012, ver.0 with latest and amdt.

Description:- Supply of cable/wire indoor copper conductor single/multi core plain annealed high

of the following sizes:- (i) Wire 1*1mm/16*0.2mm (to be procured From RDSO Approved Source only) Inspection by Consignee

Description:- Fabrication, supply and fixing of scaffolding/ cable carrier of angle iron of size 35mmx 35mm x 5mm andflat of size 25mmx3mm as per instructions of Engineer at site. The space between two flats shall be 25cm or less as per site requirements . All material required for scaffolding / cable

cement & concrete etc, will be supplied by the contractor. This also includes insulating flat strips, cleaning, priming by red oxide, painting by ISI mark paint and writing of description of relays by ISI mark paints. Inspection-Consignee for supply portion LUCKNOW-NR-DIVISION-S AND T/NORTHERN RLY

Description:- Supply of Insulation sets for ground connection for made of nylon-66 for 220mm throw point machine as per Specn. No. IRSS-40/84 or latest.one set consisting as follows: 1) Insulating Washer drg. No. S-8640-12 Nos, 2) Insulating Washer drg. No. S-8640/1 -04 Nos, 3)

Insulating Bush drg. No. S-3463 -1 No, 6) Insulating Bush drg. No. S-22179-02 Nos, 7) Insulating Bush drg. No. S-8912 -02 Nos, 8) Insulating Plate drg. No. S-3404 -02 Nos, 9) Insulating Bush drg. No. S- 8813-04 Nos, 10) Insulating Plate RH Drg. No. S-3592 -01 Nos, 11) Insulating Plate LH Drg. No. S-

& painting for operating panel of reputed make compatible with existing panel and as per site engineer. Inspection Consignee

compatible with existing panel and as per site engineer. Inspection- Consignee

with existing panel and as per site engineer. Inspection- Consignee

indication wiring 1.15 mtr and fitted with 24 V DC LED Lamps of reputed make compatible with existing panel and as per site engineer. Inspection- Consignee

SSDAC as per RDSO Specification No. RDSO/SPN/177/2012 (Ver.3) or latest. Inspection- RDSO

SSDAC as per RDSO Specification No.RDSO/SPN/177/2012 (ver.3) or latest. Inspection- RDSO

existing installation of Electric lifting barrier. Inspection- Consignee

694:1990 reaffirmed 1995 or latest suitable for railway electrification area shall be of reputed make like Delton, LAPP, Finolex, or superior. Inspection: Consignee