SPL REPAIR TO BLDG NO P-430 (MT/LRW OFFICE), P-461 (SINGLE OFFR ACCN), P-419 AND 421 (SINGLE JCO LIVING ACCN), P-463, 464 AND 465 (OFFRS MESS) AT SRI GANGANAGAR MIL STN

Dismantling of brick tiles or terracing tiles single layer on roof & disposal of retrieved material upto a distance n.exc 100m where directed, all as specified.

Demolition of mud any form of soil in roof, any depth including plastering and leaping (where full thickness removed disposal off rubbish upto a distance n.exc 100m, where directed.

Demolition of Cement concrete (unreinforced) of any description and in any position/old existing felt/plaster/tiles etc including removal of demolished matrial out of defence land complete all as specified.

M&L for levelling course for roof slab, PCC type B0,1:2:4(12.5 mm graded aggragate) using waterproofing compound (SBR) for maintaining proper roof slope and finishing sirface even and smooth without using extra cement complete all as specified .(Minimum thickness of concrete should not be less than 50mm at any point) Note :- Waterproofing compound should be measured and paid seperately.

Supply of SBR waterproofing compound @ 2% of per Kg cement used complete all as specified. Make:- Fosroc / Sika/ Choksey / Chemsol / Bostik/ STP

OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm. (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.

M& L for making benching with PCC (1:2:4) type B0 using WPC along side wall adjoining to roof in concave shape complete all as specified.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames).

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and removal complete all as specified

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge . S&F shall include the followings :- Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finished sliding door bolt 300mm -01 Nos per leaf (e)Stainless steel (304 grade ) finished floor door stopper -01 Nos per leaf Note : 1. Test certificate of manufacturer to be provided by contractor. 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/guage skeleton door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws,including s&f of stainless steel steel 304 grade (natural finish) wire cloth , all as per direction of Engineer-In-Charge including S&F following items :- Note : (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c)stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d)stainless steel (304 grade) finishedsliding door bolt 300mm -01 Nos per leaf (e)stainless steel (304 grade) finished floor door stopper -01 Nos per leaf(f) stainless steel (304 grade) wire cloth fixing as per manufacture. Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. for fixing MosquitoMesh and XTN aluminium mesh combinely panel area of door except stiles and rails to be panelled wire mesh with self tapping rpund headed screws at requrd distance, scres and edge covered with feathered pvc edge beading all around mesh and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer in- Charge. S&F shall include the followings :- (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor. 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S & F factory made uPVC sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) with or without provision of opening for cooler as directed including all fittings, steel roller system, locking arrangement etc., making arrangement for fixing of hardware, glass, wiremesh, grill etc all as per manufacture instruction and Drg No BTD-890/R . Note : The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly .Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate. and cement mortar (1:3) shall be deemed to be included. Note : Description of items amend accordingly as per manufacturer instructions, Note : 1. Test certificate of manufacturer to be provided by contractor. 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S & F factory made uPVC window or ventilator side hung/top hung casement type (openable window) (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges,handles, tower bolt, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and Drg No BTD-890/R all as specified and directed. Note : The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismentalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be include. Note : Description of items amend accordingly as per manufacturer instructions, Make ( Fenesta, Saint Gobin) Note : 1: Test certificate of manufacturer to be provided by contractor. 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

M & L toughned glasss, figured glass ordinary quality 5 mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified

M & L sheet Pin headed glass 4.0mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified.

S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 – Gde – 165 complete all as specified and directed.

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc one brick complete all as specified.

Dismentling of boarding any description fixed in any position with nails/ screws complete all as specified.

M&L for providing Cupboard with shutters in required sizes &shape at site made out of HDHMR Board,18/19mm thick, density over 850kg/cum,having a classA fire rating,grade2 quality, commercial type, fixed with srews to timber frame work as in kitechen cupboard shutter/shelves/cabinet etc consisting of both side 0.9mm laminate one side decorative& other side plain. The panels shall be fabricated using adhesive and screws where ever required all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edges bent finsh as per manufacturer instruction and complete all as specified and directed by Engr-in-charge.

S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electrogalvanised of complete all as specified

S & F hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge.

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete

S&F stainless steel handles, 150 mm long complete all as specified and directed. (back plate staple D type)

Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface ( visible from front) as per Godrej Pattern complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified.

M&L for 25 mm thick cement concrete flooring type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified and directed.

M&L for vitrified Double charged/Ultracharged ceremic tiles (square / rectangular) area of each tile (size 1200 X 600mm) exceeding 0.42sqm but not exceeding 1.0 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & faircomplete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 34 above but on vertical surfaces/skirting dados etc over 10mm rendering in CM 1:4 finished even and fair, complete all as specified and directed by Engineer - in - Charge.

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.

M&L for anti-skid ceramic joint free premium quality coloured tiles 400 X 400 mm and 6-7 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar

M&L for granite (of any type) 20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over 15 mm thick screed bed in CM 1:4 etc all as specified and directed by Engineer-in-Charge.

M&L for green marblework 14 to 16mm thick (table moulded and mirror polished, area of each slab not less than0.72 Sqm) in floors, cooking platforms, window cills, top of pillars, trads of steps including 15mm thick screed bed in cement mortar 1:6 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-In-Charge. Note : 1. Green marble for window cills, top of pillars , steps should be single piece upto 1.2m length and of required width. 2. White Marble border for green marble flooring at required size would be measured and paid as in flooring area of above item.

M&L for green marblework 14 to 16mm thick (table moulded and mirror polished) in skirting on vertical surfaces as jambs of door / windows, pillars jambs of pillar,riser of steps etc including 10mm thick backing coat in cement mortar 1:4 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-In-Charge. Note: 1. Green marble for window cills, top of pillars , steps should be single piece upto 1.2m length and of required width.

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided.

Material and labour for water proofing treatment to RCC sunken slab and adjoining vertical slab as described following any one complete as per dirns of GE. Note : Plan area only measured of toilets for payment purpose. Method (A) Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, Smart Care Damp proof 2K, having 100% elongation as per ASTMD412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5 clean all working surface and made free from dirt, grease laitance etc. After inspection for all working area ough surface, cracks and construction joints are treated by polymer modified mortar 1:4:4(1 Cement: 1Polymer: 4 Sand). Making Gola of size 75 x 75m at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 (1 cement : 1 Polymer : Sand ). The coating shall be 2 parts of powder and 1 part of liquid without any water addition in he mixing and shall have consumption of 1.5Kg/Sqm per coats, etc, complete as per manufacturers specifications. (B) Bore packing:- All the borehole gaps between concrete surface and PVC pipe of various surface of various dia upto the neck of lvel of shall be filled with non-shrink free grout. – Smart Care GP Grout having dual shrinkage compensation property. Before the bore packing, surface of the PVC pipe and concrete surface will be made rough and sand sand will be sprinkled with polymer bonding agent. (C) Apply 12-15mm plaster on slab and vertical surface admixed with Vitalia Neo @200ml per bag of cement before treatment.

Material and labour for water proofing treatment to walls surfaces of toilets/baths/WC's (1600mm in toilet and 2100mm in bathroom on vertical wall surface) with following applications complete all as specified and as directed by Engineer-in-Charge :-(a) Applying first coat of chemical pidifin 2K (Dr Fixit) or equivalent on cleaned surfaces @ 0.86 Kg/Sqm (Minimum) and drying for 24 Hours(b) Applying second coat of chemical Pidifin 2K (Dr Fixit) @ 0.86 Kg/Sqm (minimum) or equivalent over first coat complete all as specified and directed.

PCC 1:5:10, type E-2 as in filling of sunken floors etc. complete all as specified and directed.

M&L 40 mm PVC(SWR) pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as spedifed

Demolition of RCC of any description such as Kitchen chimney, chajja, shelves, OHT Tanks. etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition).

M&L for reinforced nominal mix cement concrete type B1 1:2:4 (20 mm graded stone aggregate) as in Slab supported on walls for tank staging and in shelves and etc. and setting in mortar complete with joints to match complete all as specified and directed by Engineer-in-Charge.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

Use and waste of form work torough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick all as specified as directed by Engr-in-charge.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by Engineer-in- Charge.

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete, all as specified.

M&L for rendering 15 mm thick in cement mortar 1:4 (10mm thick rendering in first layer and 5 mm thick rendering in second layer)on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. Note : Supply only water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound, ISI Marked.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete, all as specified.

M&L for prepration of New plastered Internal wall surface complete and applying the following :- (a) Applying 1.5 to 2.0 mm thick wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified. (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified. (c) Applying two coat of interior Acrylic Emulsion Roller over complete all as specified. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for prepration of New plastered External wall surface complete and applying the following :- (a) Applying 1.5 to 2.0mm thick wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified. (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified. (c) Applying two coat of Advcanced Dust Proof Emulsion using Roller over complete all as specified. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for prepration of New plastered ceiling surface complete and applying the following :- (a) M&L 1.5 mm wall care putty in two coats on ceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of interior acrylic emulsion over a coat of primer by using Airless spray / Roller over complete all as specified .

M&L for complete removal of existing treatment including filling depression of scraped surface and (a) Applying 1.5mm thick wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified. (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified. (c) Applying two coat of interior Acrylic Emulsion Roller over complete all as specified. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for complete removal of existing treatment including filling depression of scraped surface with 1.5mm thick wall care putty in one coat on old ceiling surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as specified and directed complete and applying two coat of interior acrylic emulsion of approved tint over a coat of primer on old prepared surface by using Airless spray / Roller over complete all as specified & directed.

M&L for complete removal of existing treatment including filling depression of scraped surface on Old external wall surfaces :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified. (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified. (c) Applying two coat of Advcanced Dust Proof Emulsion using Roller over complete all as specified. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.

M&L two coats of synthetic enamel exc 10 cm width /girth on OLD steel surfaces including preparation of surfaces complete all as specified and directed.

M&L two coats of synthetic enamel exc 10 cm width /girth on OLD wooden surfaces including preparation of surfaces complete all as specified and directed.

Material and labour for repair of chajja facia using cement mortar (1:3) n.exc 300 mm girth finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.

M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.

M&L for Writing letters or figures with fluorecent paint ( Block. Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.

Dismantling of brickwork built in cement mortar of any description complete all as specified and directed as per Engineer-In-Charge

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L half brick work with sub class B bricks straight or curved on plan to any radius in cm 1:4 etc.complete all as specified and directed by Engineer - in - Charge.

Dismantling and disconnecting existing CI soil waste/vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories

Dismantling and disconnecting of existing CI soil waste/vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories)

Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls / tranches with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant bend , socket , Y junction , Tee, cowl etc complete all as specified and as directed by Engineer-in- charge complete including low carbon hot roll guage corrected oil pickled and drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanized and Zn,Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed.(Note: Detail of pipe supporting system is all as per Drg NO-BTD-916). Note : UPVC PIPES AND FITTINGS AND FIXTURE -(i) The testing for leakage of pipes shall be done before connecting the pipes. (ii) All pipes shall be minimum 4'' away from wall fixed with GI bracket. (iii) The gully trap shall be minimum 90 cm away from wall. (iv) Seperates pipes for each floor should be provided. (v) Sewage and drain system shall be separate.

Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls / tranches with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant bend , socket , Y junction , Tee, cowl etc complete all as specified and as directed by Engineer-in- charge complete including low carbon hot roll guage corrected oil pickled and drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanized and Zn,Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed.(Note: Detail of pipe supporting system is all as per Drg NO-BTD-916) Note : UPVC PIPES AND FITTINGS AND FIXTURE (i) The testing for leakage of pipes shall be done before connecting the pipes. (ii) All pipes shall be minimum 4'' away from wall fixed with GI bracket. (iii) The gully trap shall be minimum 90 cm away from wall. (iv) Seperates pipes for each floor should be provided. (v) Sewage and drain system shall be separate.

Supply & fixing 110mm uPVC pipes grade 'B' bends / Elbow heavy grade of any radius/shoe with or without access door fixed to uPVC pipes as directed.

Supply & fixing 75mm uPVC pipes grade 'B' bends / Elbow heavy grade of any radius/shoe with or without access door fixed to uPVC pipes as directed.

Supply & fixing uPVC 75mm dia of floor trap with grating including jointing to waste pipes fixed in cement concrete 1:2:4 type B1 in repair complete all as specified.

Supply & fixing uPVC pipes grade 'B' branch piece, (single Y ), 75mm bore (equal or unequal), with or without access to door complete all as specified and directed by Engr-in-charge.

Supply & fixing uPVC pipes grade 'B' branch piece, (single Y ), 110mm bore (equal or unequal), with or without access to door complete all as specified and directed by Engr-in-charge.

Supply & fixing in repair uPVC pipes grade 'B' vent cowl 110mm complete all as specified and as directed by Engineer-in- charge.

Supply & fixing salt- glazed stoneware gully traps 150x150 mm , square/roung mouth, p type complete all as specified and as directed by Engineer-in- charge.

S&F vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.

S&F in repairs Vitreous china premium/1st quality wash down water closet with P trap WHITE / IVORY / Off White including connection to drain (or outgoing pipe) and to flushing pipe , anti syphonage pipe etc and including plastic soft closed seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc and including S&F of all necessary accessories set like rag bolts / gel gasket / hinges etc as recommended by manufacturer for fixing , packing and taking down of any description / size complete in all respect all as specified and as diretded by Engr-In-Charge.

S&F in repairs concealed flushing cistern of PVC 8 Litres cap with dual flushing system , valveless symphonic action type , with inlet , outlet , ball valve, float and including brackets and connection to pipes etc and including S&F of all necessary accessories / installation kit and S type drain pipe connection set for wall hung WC wtc as recommended by manufacturer for fixing , packing and including S&F of actuator knob / flush plates and taking down existing any description / size complete in all respect all as specified and as diretded by Engr-In-Charge.

S&F in repair Health faucet ABS body MS Chromium plated suitable for 15mm dia pipe with 1.25m long flexibile tube and ABS wall hook including making connections and fix in position complete in all respect as specified and directed by Engr-In-Charge

S&F vitreous china urinals, Half stall type flat back complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including waste couplings of stainless (half or full threaded) of 32 mm and also including low density polyethylene pipes (LDPE) 32 mm*800 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer in charge .

S&F Urinal spreader of PTMT any colour for fixing 15 mm dia pipe complete all as specified and directed by Engineer in charge .

Supplying and laying of 20mm (outer dia) (15mm inner dia) cpvc pipes SDR 11 & plain CPVC SDR 11 bend fittings on wall/ ceilings or laying in floors & including cpvc coated brass elbow, T, Male/ Female brass threaded adaptor etc. also including Taking up or down GI tubing 15 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. In brick walls.

Supplying and laying of 25mm (outer dia) (20mm inner dia) cpvc pipes SDR 11 & plain CPVC SDR 11 bend fittings on wall/ ceilings or laying in floors & including cpvc coated brass elbow, T, Male/ Female brass threaded adaptor etc. also including Taking up or down GI tubing 20 mm bore pipe including cleaning for re-fixing or removal to store complete all as specified and directed by Engr-in-charge.

Dismantling water tanks of any description exc 250 and n.exc 1000 ltrs capacityand removal from site all as specified and directed.

S&F 500 ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) including 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe hoisted and fixed in position all as per specified and directed.

S&F rotational moulded polyethylene water storage tank 1000 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed by Engineer - in - Charge.

S&F 25 mm bore gate valve cpvc with handle, screwed both ends for inlet & outlet pipe and fixed complete all as specified and directed.

S&F 15mm bore Long body bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F CP angle valve for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type fixed as in repair.

S& F single lever High flow divertor consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure all as specified.

S&F in repair brass chromium plated shower rose 125 mm of size with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed

S&F in repairs Brass CP Kitchen Mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S&F in repairs central hole wash basin mixer 15mm bore brass without polp up waste with 10mm dia 450mm long copper pipes.

S&F in repairs Brass CP wall Mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm of approved quality complete all as specified

S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed by Engineer in charge.

S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S & F in repair stainless steel towel ring min 30mm dia including brackets complete all as specified and directed by Engineer - in - Charge.

S & F in repairs stainless steel toiler paper holder fixed with screw/ necessary fittiings complete all as specified and directed by Engineer - in - Charge.

S&F corner glass self 300mm ( withBrass Brackets) fixed with chromium plated screws etc all as specified and as directed

S&F in repairs Stainless Steel grating 125mm dia with waste hole (Minimium weight 40 grams).

S&F in repairs Stainless Steel grating 100mm dia without hole (Minimium weight 25 grams).

S&F stainless steel peg set including making holes complete all as specified.

S&F in repair sinks bowl type, made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe including 40mm dia CP Brass waste fitting amd waste pipe overall size of SS sink 495mm x 420mm bowl size 410mm x 330mm x 160mm, etc complete all as specified and as directed.

S & F in repairs stainless steel Kitchen plate rack of overall minimum size 900mm x 750 mm x 250mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick sheet fixed with rawl plug and CP steel screws complete, all as directed.

S&F in repairs stainless steel curtain rod 25 mm dia (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed by Engr-in-charge.

Material and labour for mild steel ISMB, Joist, channel, angle or teee sections, fixed adjacent to ceiling and embedding in floor and brickwork including cutting welding, without connection plates, etc. (cut to ordinary lengths i.e. Within 20mm of the length indicated) FE 410 W(GdeE-250) quality 'A' complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

PCC (1:3:6) type C-2 (using 40mm graded agg) 75mm thick as in plinth protection .

M&L for 75 mm thick cement concrete , 1:4:8 type D2 (Using 40mm graded stone aggregate) flooring,paving etc. concrete complete all as specified and directed.

M&L for Machine pressed Precast cement concrete interlocking coloured ( glossy finished / ruberised paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with and including 25mm thick sand cushining complete all as specified and directed by Engr-in-charge.

M&L for 25 cm x 25 cm/30cmx30cmx (20 to 25) mm thick machine pressed chequered cement concrete tiles(rubber moulded) set jointed and pointed in neat cement slurry in floors with grey cement including 15mm thick screed in CM 1:6 with pigments complete all as specified and directed by Engineer-in-Charge.

Supply and laying factory made kerb stone of M-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed.

Dismantling Asbestos cement ( corrugated, semicorrugated ,etc.) sheets in roof coverings complete all aspecified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed by Engineer in charge.

M&L PCC 1:2:4 (40mm graded stone aggregate) type B2, in foundation of posts and struts complete all as specified and directed .

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 complete all as specified and directed .

M&L mild steel work as in framed work i.e. Angle iron/flat iron including caps , bases, splices, all lattice bars, cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed .

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L two coats of synthetic enamel over a coat of red oxide primer exc 10 cm width /girth on new steel surfaces including preparation of surfaces complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, screwed end to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long complete all as specified and directed by Engineer - in - Charge.

S & F for Rolled mild steel in plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk) forming holes , without any attachment conforming to Fe-290 grade E-165 complete all as specified and directed .

S & F Solid laminated both side with coloured PVC Wall paneling/Lining con-sisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed by Engr-in-charge. Note : Colour of paneling will be approved by GE

S & F for 5mm thick laminated both side with coloured PVC sheet fillet of width 35mm for wall paneling frame work inclusive of fixing on to wall to make PVC Frame as per specification and draw-ing complete all as specified and directed by Engr-in-charge. Note : Colour of panneling will be approved by GE

Dismentling wall and ceiling boards ( fibre, pulp, insulation ,etc. ) or insulation boards/slabs/blankets, any thickness, including cover fillets complete.

S&F for Hangers 3mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long as in hook and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F for Anodised aluminium snap grid frame work for false ceiling all as per specified and directed by Engr-in- charge.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsumanhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) complete all as specified and directed. Note : Design of ceiling shall be approved by GE

S&F GI wire netting 0.9mm dia and 12mm mesh lathing to wood or metal studding, joists etc in walls, ceilings stanchions, beams etc includings all laps, cutting and waste as per specified and directed by Engr-in-charge.

Dismantling structural steel work including rolling shutter /door, gates and staircase railing but excluding framed truss complete all as specified and directed by engr-in-charge.

M& L for providing and fixing stainless steel (Grade 304) railing made of Square hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) & Providing baluster and necessary fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

Carefully chipping, removing existing loose/ damaged concrete with plaster from Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items by low impact high frequency hammer/ chipper without damaging the existing sound concrete and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade, making the edges straight and even and cleaning it by wire brush and then by air blower and removal of rubbish outside MoD land complete as specified and as directed by Engr-in-charge.

Cleaning all existing reinforcement bars in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items with wire brush/rotary wire brush to make entire circumference surface of bars free from rust scales, loose material, dirt etc., complete and applying alkaline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, complete as per manufacturers instructions, all as specified and directed. (Mode of measurement: per sqm of breaking area of concrete.) Make : Sika- Rustoff 100/Fosroc- Reebaklens RR/OM AGRO- DERUSTER/ Pidilite Dr Fixit Rust Remover/Asian Paints Apcorep rust remover or Techno commercial equivalent make approved by GE in writing from E-in-Chief Br approved list.

Providing and application of Zinc rich epoxy anti-corrosive protective coating for reinforcement bars as corrosion protection system in 2 coats to the entire circumference surface of bars (consumption Qty as per manufacturers instructions but min 0.4 kg/Sqm approx) in beams complete all as specified and directed by Engr-in-charge. The product should confirm carbonation resistance of 2 mm and bond strength > 1N/sqmm according to ASTM C 882-78 (Mode of measurement: per sqm of application area of concrete.) Make : Sika- Friazinc R/ Fosroc- Nitozinc Primer/ Pidilite Dr Fixit Zinc Rich Primer/ Asian Paints Apcorep rust coat RB or Techno commercial equivalent make approved by GE in writing from E-in-Chief Br approved list.

Apply SBR based bonding agent to the entire concrete surface prior to building up of concrete with Polymer modified mortar or any other treatment , including cleaning the surface to remove dirt, dust or any other impurities on the surface, etc. complete in Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items. Make : Sika - SikaDur 32 LP/ Fosroc - Nitobond SBR (EP)/ Pidilite Dr Fixit Super Latex (EP)/ Asian Paints Repair Polymer or Techno commercial equivalent make approved by GE in writing from E-in-Chief Br approved list.

Rebuilding the section of structural damaged RCC/PCC elements of Roof, Ceiling, Chajja, Fascia, Fins, Drops repair to spalling concrete to its original size and shape , layer of 10mm average thickness 1st layer by providing and applying with pre-batched, one component fiber based repair mortar having compressive strength >= 50 N/sqmm (28 days) according to ASTM C 109; flexural strength >= 5N/ sqmm (7 days) according to ASTM C 293-79. complete all as specified and as directed by Engineer-in-charge Make: Sika - Monotop 122 F/ Fosroc - Renderoc S2/ Pidilite Dr Fixit Polymer Mortar HB or Techno commercial equivalent make approved by GE in writing from E-in-Chief Br approved list.

All as per item No 147 above but for each addl 10mm uniform thickness for subsequent layers

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Ser item No 150 above but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 150 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 150 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 150 above but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 150 above but for call bell point complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 150 above but for Industrial Socket on independent board with copper conductor 4 Sqmm complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge.

S & F Modular switch 1 way 16A, with box complete all as specified and directed by Engineer - in - Charge.

S & F modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amps single pole two ways complete all as specified and directed by Engineer – in - Charge.

S & F modular socket outlet 5 pin 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge.

Supply and fix in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S&F modular bell push 5 Amp complete all as specified and directed by Engineer – in - Charge.

S & F modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S&F Buzzer AC 230 single pole Volt ding dong type complete all as specified and directed by Engineer - in - Charge.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of existing light fitting with LED batten with aluminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

S & F in replacement LED Bed side Light (White,3000k) 3 Watt, with flexible arm suitable for reading complete all as specified and directed by Engineer - in - Charge.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engineer - in - Charge.

S & F in replacement compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

S&F in replacement sub main two single core PVC copper conductor unsheathed wire multi stranded 4 sqmm FRLSH including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc and including 4.0 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge. Note : Two lengths of 4.0 sqmm cable and one length of 4.0 sqmm earth cable along with PVC conduit will be measured as one running length

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 250A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs MCCB 4 pole 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S & F sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘C’ series type suitable for 240 volts, AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store.

M & L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan.

S&F exhaust fan made of sturdy engineering plastic of 250mm sweep ,240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

S & F Rigid non-metallic PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.

Supply and fix electric water heater, storage type Plastic/plastic+sheet steel body with glass coating SS tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Supply and fix Water heater storage type, electric,capacity 50 litres.BEE 5 star rated complete with all electrical fitting complete all as specified and as directed by Engr-in-Charge.

S&F TV socket having holes for 20mm conduit entry for tv connection all as specified and directed by Engr-in-Charge.

Please Enable Macros to View BoQ information