REPAIR TO DRAINS FOOT PATH PLINTH PROTECTION COMPOUND WALL GARRAGE SHEDS AND FENCING ETC AT MD ACCN COMPLEXES OF AGE BR II UNDER GE MIS MHOW

Amount

Demolition of cement concrete of any description not exceeding 15 cm thickness (below or above ground level)complete all as specified and directed.

Demolition of reinforcement cement concrete of any description not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of brick work built in cement mortar in any position including all quoins, arches & pillars etc.complete all as specified and directed.

M&L for Brickwork with fly ash brick by using Modular size brick , straight or curved on plan exc 6m mean radius built in CM 1:6 complete as directed and specified..

M&L for plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation and mass concrete etc., complete all as specified and directed

M&L for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate in surface channels and drains complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in roof kerbs, mud stops,steps, coping small sumps and like items slightly rounded or chamfered on the edges complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for rendering 15mm thick cement plaster in CM ( 1:4 ) on fair faces of brick or concrete surfaces and surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc.complete all as specified and directed.

M&L for add or deduct for each 25mm girth or part there of over or under 30cm inner girth drain or channel in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc.complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs landing and similar work no exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and thee like complete all as specified and directed.NOTE: Reinforcement shall be measured and paid separately under relevant item.

S&F Mild steel TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition and breaking up drain pipes (SWG, AC or RCC) of 300mm bore pipe set in cement mortar including cement mortar bedding complete all as specified and directed.

M&L for Reinforced concrete pipes 300mm dia , class NP3, laid and jointed complete with collars including PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in bed drain pipes packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in soil including spreading, levelling, watering and well ramming in layers n exc 25 cm thick. complete all as specified and directed.

Removing excavated soil to a distance exc 250m and n. exc 500 m and deposited where directed at a level not exceeding 1.5 metre from starting point complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified and as directed.

M&L for chequered cement concrete tiles with grey cement and pigment of size 25cmX25cmX25mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for chequered cement concrete tiles with grey cement and pigment of size 40cmX40cmX40mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for machine cut kota stone slab in flooring 20-25mm thick of size not less than 595x595 mm as in floor and laid over and including 15mm thick screed bed in CM 1:6 & set jointed and pointed cement mixed with pigment to match the shade of slab including necessary polishing complete all as specified and as directed.

M&L for machine pressed rubber moulded precast concrete interlocking coloured paver block (glossy finished) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over stone dust cusion and jointed with filled with sand complete all as specified and directed.Note: stone dust cushioning shall be measured and paid separately.

M&L for stone dust under floors including spreading, watering and consolidation complete all as specified and directed.

M&L for hardcore with broken stone of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spkes, framed guard bars barred iron doors ladders framed balusters walk ways railing framework of water tanks and similar work conforming to Fe 410-0 OR Fe 310-0 complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings etc complete all as specified and as directed.

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof seeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.

Dismantling of timber scantlings as in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in un-framed work complete all as specified and directed.

S&F mild steel Hollow Section work in tubular trussles, purlins, rafter, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified and as directed.

S&F mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified and as directed.

S&F Mild steel plates (Plain or chequered) as in shoe plate, base plate and gusset plates forming holes for roof frame work, trusses, rafters etc of grade Fe 410 WA. complete all as specified and as directed

M&L for preparation of newly steel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide complete complete all as specified and as directed

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concreteany section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling of GI plain/ GI barbed wire any description complete all as specified and directed

Dismantling fencing wire mesh,any type complete all as specified and directed

Excavating post holes or similar holes, each not exceeding 0.5 cum getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and directed by Engr in Charge.

M&L for PCC 1:2:4 type B2 using 40 mm graded aggregate as in foundation ,post, etc complete all as specified and directed by Engr in Charge.

S&F, Mild steel angle iron (Fe-310) as in posts, struts,flat iron( for securing wire mess etc ) in fencing including cutting top to shape required, drilling holes, notching for wire,erect & fixed in true position etc complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc., including provision of binding wire. complete all as specified and directed by Engr in Charge.

supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

M&L for repair/ maintenance of existing rolling shutter of any description and in any postion of size not exceeding 3.0 sqm by taking down the shutter, keeping aside for repairs by replacing defective parts/components such as hood covers,gudie channels, lock plate,spring wheel ,ball bearings,shafts, etc with new parts including necessary welding/ revetting /bolting, punching,sealing & greasing properly as required and refixing the rolling shutter in the same postion after repairing and make the rolling shutter functionable in all respects complete all as specified and directed.NOTE: Guide channel,mild steel shutter strip,flat spring,bearing shall be measured and paid separately as supply only.

Supply only guide channel made of 3.15mm mild steel sheeting, depth 50mm to 150mm (as required at site) and width of guide channel 25mm including providing fixing cleats or supports with spacing not exc 75m complete all as specified and directed.

Supply only fabricated 1.25mm mild steel black sheet for rolling shutter strip size 75mm to 100mm wide and shape as required at sitefor rolling shutter including cutting , punching on required shape and size each alternative lath section shall be fitted with MS clips secured with revets at either end complete all as specified and directed.

Supply only flat spring for Rolling shutter upto height 3.00m ( Spring weight not lees than 3.00 kg each )

Supply only 40mm dia (nominal bore ) medium weight mild steel pipe as in suspension shafts complete all asspecified and directed

Supply only ball bearing Make -: SKF/NBC

For 50mm size

For 100mm size

Chitragupta Construction

Goyal Construction

sunway associates

NIDHI CONSTRUCTION

APconstruction