Construction of protection wall and raising and construction of inspection path between intermittent location from RD 0m to RD 2700m on both banks of Mungeshpur Drain

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of approprite length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used. : 450 mm dia piles

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. : Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand)

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Hiring and Running charges of JCB (3D) with fuel and operator where ever required on Direction of the Engineer-In-Charge

Providing and laying cement concrete pavement of M-10 with ready mixed concrete from batching plant of reputed cement manufacture and to the site of work in transit mixer having continucus agitated mixer, manufacture as per mixed design of M-10 grade of cement concrete work including pumping of RMC from transit mixer to site. Placing in required camber compusory with plate / screed vibrator, with wire brush etc. and curing including cost admixer in recommended proportions as per IS : 9103 to accelerate / retar setting of concrete. Improve workabitly without impairing strength and durability as per specification and direction of Engineer-In-Charge. Note:-1. Excess / less cement used than specified in this item is payble / recocerable separately. M-10 grade plain cement concrete by using 220 Kg of cement per cum of concrete.

Providing and laying (RMC) of M-30 grade by using minimum 400 kg of cement ( 43 grade O.P.C) per cum of concrete, in roads/streets using manufactured in automatic RMC using coarse sand and graded stone aggregate of 20 mm nominal size in appropriate as per approved design criteria, including transportation to site in transit mixer, including cost of so mixture in recommended proportion as per IS 9103 to accelerates / retard setting of concrete to improve workability with out impairing strength and durability as per specification including spreading and compacting mechanically using needle and surface vibrators, leveling to required slope & camber, finishing by floating & brooming with wire brushes etc and curing including making provision for contraction expansion construction of cross longitudinal joints (10mm wide x 50 mm deep) by groove cutting machine providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer in- charge ( Cost of joint filler & sealants shall be paid for separately under relevant items )./ Note cement content considered in M-30 is @ 400kg/cum. less cement used as per design mix is / Recovery separately M-30 RMC by using minimum cement @ 400 KG/Cum cement manufactured in automatic batching plant ( RMC plant ) including transportation to site in transit mixture

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor 2nd level, excluding the cost of centering,shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). (6547.70 - 482.15 =6065.55)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submitt the design of loading platform for the approval of Engineer-in-charge. Single pile upto 50 tonne Safe capacity. Routine test (Test Load 1.5 times the Safe capacity)

Please Enable Macros to View BoQ information