SPL REPAIR/ REPLACEMENT OF OLD TERRAZZO TILES IN MD ACCN OF SECT D AND ADDN/ALTN OF BLDG NO T-30 AT DINJAN MIL STN UNDER GE DINJAN

Amount

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Materials and Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

M&L for broken stone bolder as hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as as specified and as directed.

M&L for Cement concrete 1:4:8 Type D 2 (using 40 mm graded aggregate ,in foundations, filling and mass concrete complete all as as specified and as directed.

M&L for PCC 1:2:4 Type B0 (using 12.5mm graded agg. ) as in hold fast and filling of steel chowkhat etc, complete all as specified and directed.

M&l for Reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (using 20 mm graded stone aggregates) as in Slabs supported on walls, beams and columns, in floors, roofs, landing balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforcement cement concrete (Nominal Mix) 1:2:4 type B1 (using 20mm graded stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&l for reinforced cement concrete (Nominal Mix) 1:2:4 type B1 (using 20 mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Demolition of brickwork built in cement mortar including taking out roots vegetation if any at any position and removal from site, complete all as directed.

M&L for brick work with sub class -B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for brick work with sub class -B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and as directed.

M&L for 40mm thick Damp proof course cement concretre 1:2:4 type B0 (using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork and mixed with WPC as per Manufacturers instruction complete all as specified and as directed. (Note: WPC shall be measured and paid separately as supply only)

Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste Formwork Flat to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mmthick (Horizontal or sloping) in flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste Formwork to sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. in flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste Formwork to sides of square ,rectangular or polygonal pillars, posts, struts, piers, columns and stanchions in rough finished surfaces of concrete complete all as specified and directed.

Taking down Shutter of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening with Miscellaneous repairs complete all as directed.

M&L for 35mm thick 2nd class Hardwood, plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part I), kiln seasoned and chemically pressure treated complete all as specifed and directed.

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm long alluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 125mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 300mm long Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F 100 mm long butt hinges,medium weight, cold rolled mild steel fixed to chowkats complete all as specified and directed.

S&F in repairs 100 mm long Butt hinges, medium weight, cold rolled mild steel fixed to Chowkats complete all as specified and directed.

S&F alluminium handle 100mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F for tabular towel rail 20mm dia D type,60cm long brass chromium plated between flanges complete as specified and directed

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railing framework of water tanks and similar work conforming to fe 290 Gde-E-165 complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 6 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F Joist channel, angle,or tee sections of Fe 290 (Gde E-165) fixed independently, without connecting plates etc,(cut to ordinary lengths i.e within 20mm of the length indicated) complete all as specified and directed.

S&F rolled sections of Fe-290 Gde-E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F rolled mild steel work in roof trusses (framed ), trussed, purlins crane gantries , rafts and fastening and heavy brackets framming (beams tee,angle channel and or flat sections) including distance pieces, cleat nut bolts etc quality confirming to Fe-290 Gde-E-165) complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, devetailed or welded complete as specified and as directed.

S&F steel ventilator with top hung shutter including hinges,steel peg stay complete all as specified and as directed.

S&F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed.

S&F anodised aluminium ventilator shutters, side hung type without sash, aluminium sectiion weighihg 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber e packing, anodised snap beading screws door, anodised aluminium fitting such as peg stays 150mm long(1No.) hinges type B-21 100mm long (2 No) complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding/ridges etc , fixed with self tapping screws complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8, type D-2 (ussing 40mm graded stone aggregate ) as in sub base of flooring etc complete all as specified and directed.

M&L for 75mm thick, plain cement concrete 1:3:6, type C-2 (ussing 40mm graded stone aggregate) as in plinth protection, finishing cemengt concrete suerface even and smooth without using extra cement complete all as specified as direected.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregates) as in floor complete all as specified and directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregates) as in floors etc. finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as directed.

M&L for Coloured Glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over and including 10 mm thick rendering as backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering as back coat in cement motar 1:4 complete all as specified and directed.

M&L for light shade vitrified Ceramic tiles 10 mm thick (Square/rectangular) polished, area of each tiles exc 0.36 sqm but n exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick sscreed bed or bedding layer in cement mortar 1:6 for laying floor tiles complete all as specified and directed.

M&L for light shade vitrified Ceramic tiles 10 mm thick (Square.rectangular) polished, area of each tiles exc 0.36 sqm but n exc 0.42 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering as backing coat in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as directed.

M&L for 10mm thick rendering on other than fair face of brick works or concrete surfaces of walls with CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 20mm thick in two layers of 10 mm thick each in cement morter (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only Integral liquid water proofing compound conforming to IS-2645-2003 complete all as specified.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant cement primer complete all as specified and directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of distempering interior walls with distemper oil emulsion white or tinted over a coat of chalk whiting primer over 3mm thick wall care putty complete all as specified and directed.

S&F for 3mm thick sheet glass ordinary quality and glazed with oil putty or fixed with beads in square n exc 0.5 sq.m. each pane complete all as specified and directed. .

M&L for painting steel iron surfaces of any description over 10cm in width or grith not otherwise described and applying two coats of synthetic enamel paint over coat of red oxide primer including preparation of new surface complete all as specified and directd.

S&F and laying of 16mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete as specified and directed.

S&F and laying of 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete as specified and directed.

S&F 16mm dia CPVC Brass thread elbow complete as specified and directed.

S&F 20mm dia CPVC Brass thread elbow complete as specified and directed.

S&F 16mm dia CPVC Brass thread Tee complete as specified and directed.

S&F 20mm dia CPVC Brass thread Tee complete as specified and directed.

S&F 16mm dia CPVC Brass thread union complete as specified and directed.

S&F 20mm dia CPVC Brass thread union complete as specified and directed.

S&F 15mm bore bib taps fancy type CP with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferule and fixed complete all as specified and directed.

S&F 15mm bore pillar taps chromium plated fancy type cast copper alloy, with capstan heads screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F 15mm bore stop valves(concealed type) cast copper alloy fancy type chromium plated long sunk and cup screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 32mm waste coupling of PTMT (half or full threaded) minimun weight 32mm 45gms/40mm-60gms complete all as specified and directed

S&F for PVC connections 15mm size with PTMT nuts length 600mm complete all as specified and directed

S&F 110mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches complete as specified and directed.

S&F 75mm PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls complete as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius complete as specified and directed.

S&F 75mm bore PVC (SWR) bends of any radius complete as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single (single T) equal or unequal complete as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white with "P" or "S" Trap front or back inlet fixing bolts, PVC seat cover complete and making all necessary connection complete all as specified and directed.

S&F PVC low level flushing cistern 10 litre capacity,valveless symphonic action type with inlet ball valve float and handle incl bracket, PVC connection pipe and flush pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and directed.

M&L for PVC (SWR) Floor trap 75mm dia plain with grating including jointing with solvent cement including disconnection of old existing trap, and connected with existing water pipe complete as specified and directed.

M&L for PVC( SWR) gully trap 125/110mm setting and jointing with solvent cement complete as specified and directed

S&F Sinks made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowL size 410mm x 330mm x 160mm complete all as specified and directed.

S&F High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm complete all as specified and directed.

S&F Vitreous China wash hand basin, white, flat back, size 550x400mm with coupling , waste, chain and plug and porcelain stopper, brackets, with and incl 32mm dia 90cm long PVC waste down pipe, but excluding taps complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

M&L for Forming construction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLHS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point terminated in and including 1.6mm thick mild steel sunken terminal box of suitable size with 3mm thick hylam sheet top cover fixed with suitable size of brass screws suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per item No. 95 above but one 5 pin switch socket combination, 5 Amps on Independent board.

All as per item No. 95 above but one 5 Amps, 3 pin socket outlet on the same board with other switches.

All as per item No. 95 above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 amp multi socket out let on independent board complete all as specified and directed by Engineer-in charge.

S&F for switch piano, 5 Amp single pole, flush type one way 230 volts complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 3 pin, 5 Amps, flush type, 240 volts complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5/16 Amps, 240 volts, flush type complete all as specified and as directed.

S&F for socket outlet, 5 in 1, 5 Amps, 240 volts, flush type complete all as specified and as directed.

S&F for ceiling rose, 3 Terminal/PVC/Polycarbonate, isolated body including suitable PVC block/box complete all as specified and as directed.

S&F for stepped type electronic fan regulator (5 step) flush type complete all as specified and as directed.

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with 9W bulb complete all as specified and as directed.

S&F for 20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed.

S&F factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts suitable for housing MCBs complete all as specified and as directed.

S&F MCB, 'C' Series, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed.

S&F MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed.

Supply, installing, testing and commissioning of light duty metal anti dust exhaust fan, suitable for Single Phase AC supply, earthing etc, power input 50 W, 220/240 V, 300 mm sweep size, fan speed 1350 RPM, 3 nos. blades, copper winding, Air delivery minimum 1160 CMM and including all fixing accessories complete all as specified and as directed. Make : Cropmpton/Bajaj/Khaitan/havells/Orient.

M&L for Making circular hole for fixing of exhaust fan 300 mm sweep and making good the disturbed surfaces by plastering and painting the surface matching with existing color complete all as specified and as directed.

S&F circular louvers sutiable for 300 mm sweep complete all as specified and as directed.

S&F ceiling fans complete with blades, down rods, remote and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

S&F 35 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

S&F street light bracket arm of length not less than 1.5 m made out of GI tubing, 40 mm bore, light grade fixed to pole, etc with suitable size flat iron clamp, nuts, bolts including painting with two coats of aluminium paint over a coat of red oxide, zinc chrome primer on steel surfaces complete all as specified and as directed.

Supply and laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 10 Sqmm 2 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

M&L for bricks laid in trenches for LT cable protection with length of brick perpendicular to length of cable complete all as specified and as directed.

Boring of holes horizontal for laying not less than 40mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed. Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.

S&F in repairs 25 mm bore dia, steel tubes, galvanised, light grade with all fittings and fixed complete laid in trenches /wall for protection of cable complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete all as specified and as directed.

STANDARD ELECTRIC WINDERS (BID ID -3101379)

MAZUMDAR ENTERPRISE (BID ID -3102968)

Bimal Trading Company (BID ID -3103910)

FREEZCON (BID ID -3101193)

M/s GANDHESWAR PHUKAN (BID ID -3100942)

Construction House (BID ID -3102011)

NChetia and Sons Trading (BID ID -3105597)