REPAIRS/MAINTENANCE TO STEEL AND WOODEN FURNITURE AT AIRFORCE STATION KALAIKUNDA UNDER GE (AF) KALAIKUNDA

Amount

Taking down carefully existing unserviceable seat frame from chair CB steel without arm and S & F new seat frame made out of 2nd class hard wood duly caned with white plastic cane 2mm wide for seat and 3mm wide for border as per Godrej pattern Cane, Type-I (HDPE) as per IS: 5378-1994 and applying two coat of black French polish with glossy finish over wood filler on all exposed new wooden surfaces after preparation of new wooden surface complete over a coat of primer before canning complete all as shown on drawing. (FD-75M) as specified and as directed by Engineer-in-Charge

All as per item No 01.00 here- in -before but back frame of chair CB steel without arm. Complete all as directed by Engineer-in-Charge

S & F for mild steel cleats of flat iron size 25x3mm with drilling holes for fixing with MS screws to seat and back frame of each chair frame to support to seat/back wooden frame including applying two coats of synthetic enamel OG/Grey paint over a coat of red oxide primer all as directed Complete all as specified and as shown on drawing (FD-75M) and as directed by Engr-in-charge.

S & F for pair of 25mm width, 16 gauge 460mm long flat iron for support between the seat and back frame of each steel chair frame including applying two coats of synthetic enamel OG/Grey paint over a coat of red oxide primer all as directed , all as specified and as shown on drawing (FD-75M) and as directed by Engr-in-charge.

Taking down carefully existing unserviceable seat frame from chair CB steel with arm and S & F new seat frame made out of 2nd class hard wood duly caned with white plastic cane 2mm wide for seat and 3mm wide for border as per Godrej pattern Cane, Type-I (HDPE) as per IS: 5378-1994 and applying two coat of black French polish with glossy finish over wood filler on all exposed new wooden surfaces after preparation of new wooden surface complete before canning complete all as shown on drawing. (FD-75M) as specified and as directed by Engineer-in-Charge

All as per item No 05.00 here- in -before but back frame of chair CB steel with arms, complete all as directed by Engr-in-charge.

All as per item No 5.00 here- in -before but Taking out all unserviceable/damaged hand rest from its position and S & F new hand rest made out of 20 mm thick teak wood plank in one piece on hand rest with piano hings at right side and applying two coat of black French polish with glossy finish over wood filler on all exposed new wooden surfaces after preparation of new wooden surface complete over a coat of primer before canning complete all as shown on drawing. (FD-75M) as specified and as directed by Engineer-in-Charge

All as per item No 5.00 here- in -before but S & F new mild steel cleats of flat iron size 25x3mm with drilling holes for fixing with MS screws to seat and back frame of each chair frame to support to seat/back wooden frame including applying two coats of synthetic enamel OG/Grey paint over a coat of red oxide primer all as directed Complete all as specified and as shown on drawing (FD-75M) and as directed by Engr-in-charge.

All as per item No 5.00 here- in -before but S & F for pair of 25mm width 16 gauge 460mm long flat iron for support between the seat and back frame of each steel chair frame including applying two coats of synthetic enamel OG/Grey paint over a coat of red oxide primer all as directed , all as specified and as shown on drawing (FD-75M) and as directed by Engr-in-charge.

Material and Labour for repairable parts from Table office officers and Table office clerk steel and taking out of repairable table drawers and refixing on existing position.Removing the dents and bends,welding /riveting the damaged portion and rectifying the smooth movement of the drawers. incl. painting with two coat of OG or approved synthetic enamel paint over a coat of red oxide primer complete as shown in the drg (FD-1003 &1004) and as directed by Engr-in-charge.

All as per item No 10.00 here- in -before but Taking out and removing old unserviceable drawers and supply & fixing 1.00 mm thick new drawers as per existing made out of (1 mm) plain black steel sheet (PBI sheet) fixed by run welding incl. painting with two coat of OG or approved synthetic enamel paint over a coat of red oxide primer complete as shown in the drg (FD-1003 &1004) and as directed by Engr-in-charge.

All as per item No 10.00 here- in -before but Taking out and removing of old unserviceable lock from drawer from its position and S & F new 6 lever brass chromium plated lock with keys in duplicate and make it smooth functional complete all as specified and as directed.Make: Godrej/Harrison/Link

Removing the old unserviceable/broken handle of Almirah large steel with shelves/Almirah medium steel with shelves/Locker bed side steel and supply & fixing new CP brass handle best quality as approved by GE as per drg and as directed by Engr-in-charge. (FD-1031,1032 & TP)

Taking out and removing of old unserviceable lock from its position and S & F new 6 lever brass chromium plated lock with keys in duplicate and make it smooth functional as per drg (FD-351,1031,1032,1028,1029 & TP) and as directed by Engr-in-charge.Make: Godrej/Harrison/Link.

Taking out and removing of old unserviceable worn out MS clamps from shelves and supply & fixing with new MS clamps made out of 16 gauge MS sheet.Rest all as per drg and as directed by Engr-in-charge. (FD-351,1031,1032 & TP)

Taking out and removing of old unserviceable hinges from doors and supply & fixing with new MS hinges best qualityas per drg (FD-351,1031,1032 & TP) and as directed by Engr-in-charge.

Taking out and removing of old unserviceable old worn out unsv Leg from Almirah large steel and supply & fixing new leg made out of 20 gauge plain black sheet as per drg (FD-351,1031,1032 & TP) and as directed by Engr-in-charge.

Taking out and removing of old unserviceable Leg from Almirah medium steel/Locker Bed side steel and S&F new leg made out of 20 guage (1 mm) plain black steel sheet (PBI sheet) fixed by run welding incl. painting with two coat of OG synthetic enamel paint over a coat of red oxide primer complete as per drg (FD-1032,1029 & TP) and as directed by Engr-in-charge.

Taking out and removing of old unserviceable old worn out locking device from Almirah large steel and S&F new 6 lever steel lock as approved with keys in duplicate completeas per drg (FD-1031& TP) and as directed by Engr-in-charge.

Taking out and removing of old unserviceable old worn out locking device from Almirah medium steel and S&F new 6 lever steel lock as approved with keys in duplicate complete. (FD-1032 & TP)

Taking out and removing old worn out shelves from Almirah large steel and S&F as per existing shape and size made out of 20 guage plain black steel sheet (PBI sheet) including painting with two coat of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spraying complete all as specified and as directed and shown on drg(FD-1031 & TP)

Taking out and removing old worn out shelves from Almirah medium steel and S&F as per existing shape and size made out of 20 guage plain black steel sheet (PBI sheet) including painting with two coat of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spraying complete all as specified and as directed and shown on drg. (FD-1032 & TP)

Taking out & removing of old broken /damaged steel of door shutter with necessary cutting in square /rectangle in shape and S&F the same as per existing size & shape not exc. 100 sqcm each made out of 20 G (1 mm) plain black sheet (PBI sheet) fixed by run welding of required length incl. applying two coat of synthetic enamel paint over a coat of red oxide primer by spraying complete and shown on drg no(FD-1031,1032, & TP)

Repair to steel furniture any type with providing welding points to the joints and broken points welding points upto 10 mm sizes as under for steel furniture as various type of Almirah,Table,chair,Charpoys,Shoe Racks, Racks and Book shelves etc as directed by the Engr-in-charge.and shown on drg FD-75(M),67M,78M, 84M,77M,119, 1031,1032,1009,1003,1004,1008,1023, 1028,1029 & TP.

All as per item No 24.00 here- in -before but upto 25 mm FD-75(M),67M, 78M, 84M, 77M, 119, 1031, 1032, 1009, 1003, 1004, 1008, 1023, 1028, 1029 & TP.

All as per item No 24.00 here- in -before but upto 50 mm FD-75(M) ,67M, 78M, 84M, 77M, 119, 1031, 1032, 1009, 1003, 1004,1008, 1023, 1028, 1029 & TP.

All as per item No 24.00 here- in -before but upto 100 mm FD-75(M),67M, 78M, 84M, 77M, 119, 1031, 1032, 1009, 1003, 1004, 1008, 1023, 1028, 1029 & TP.

Material and Labour for taking out of repairable items from Chair revolving high back/Medium back of Trade Pattern for repairing/replacement by S & F new wheel base of trade pattern as per existing shape and size of trade pattern and refitting as per existing manner shown on TP directed by Engr-in-charge.

All as per item No 28.00 here- in -before but replacement of unserviceable hydraulic system from chair revolving/Chair computer and supply and fixing New Hydrolic System (Air Soft) premium quality all as per existing specification and Directed. (TP).

All as per item No 28.00 here- in -before taking out old unserviceable Seat of Chair Revolving Executive/Chair revolving high back/Computer chair and supply & fixing New Seat of Chair Revolving Executive/Computer chair all as per drawing & as directed. Note: Seat Shall be fixed over 12mm thick Hot Pressed plywood commercial and shall be upholstered with superior quality tapestry and moulded polyurithane foam 75mm thick of 50 density with PVC Lipping all round, cloth of approved shade, texture and premium quality) .

All as per item No 28.00 here- in -before but removed repairable Back from Chair revolving high back/Computer chair and supply & fixing New Back of Chair Revolving Executive all as per drawing & as directed. Note: Back Shall be fixed over 12mm thick Hot Pressed Plywood Commercial and shall be uplolstrered with superior quality tapestry and moulded polyurithance foam 25mm of 50 density and shall be disigned with contour lumber support for Extra comfort with PVC Lippling all round, cloth of approved shade, texture and premium quality)

All as per item No 28.00 here- in -before but removed repairable Armrest from Chair revolving high back/Computer chair and re-fixing on existing position by Supply & Fix new Armrest arrangements on existing Position as per Shape and size or directed by Engr-in-charge.TP

All as per item No 28.00 here- in -before replacement of unserviceable castor wheels from chair revolving /chair computer and supply and fixing New castor wheel premium quality all as per existing specification and Directed by Engr-in-Charge.

Taking out and removing following unserviceable items of Table officer steel without disturbing the other parts and supply and fixing with new items as specified made to shape & size all as per drawing and as directed. (a)Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over a coat of pink primer complete all as per drawing(FD-1002,1003,&TP) and as directed by GE/Engineer-in-Charge.

All as per item No 34.00 here- in -before but Table office clerk steel as per drawing FD-4,307,381,1004,& TP as directed by GE/Engineer-in-Charge

Table 900x900x760mm(FD-(88),291) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with widht equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss synthetic enamell paint over a coat of pink primer complete all as specified & as directed and as shown on drawing FD-291 & TP and as directed by GE/Engineer-in-Charge.

Table 900x600 mm with drawer(FD-223/283):- (a) Taking down carefully existing unserviceable top of table and S&F 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I, ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITA CHAMPA/ BONSUM /HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over and including a coat of pink primer complete all as specified & as directed and as shown on drawing

Material and Labour for taking out the old unserviceable plywood from charpoy GI pipe/Charpoy with hard top and S & F new ply wood 12mm thick with 7 Nos of ply wood commercial grade BWR type of required shape and size fixed with new screw to wooden rail complete all as specified and as directed and as shown on drg.. FD-220 & FD/E6/Map-II/01. )

Taking out existing unserviceable cane from Chair verandah steel and weaving the same with plastic cane 4 mm wide half round of approved quality duly applying Two coat of synthetic enamelled white paint of approved quality to the steel surfaces of chair before canning. NOTE :- (i) Canning shall be done in "GODREJ PATTERN" (ii) The cane shall be of "AJAY/MPI/SHAH GARWARE or equivalent"

Material & labour for preparing old painted steel surfaces by removing dents and bends, clipping, welding the damaged sheet and filling with putty and cleaning the surface to smooth to any description and of any girth and applying two coat of synthetic enamel paint 1st Quality OG/SMOKE GRAY OR AS APPROVED paint both inside and outside by spray painting all as specified in particular specification and as shown on drawing and as directed by Engineer-in-Charge for the following articles of Steel furniture (a) Almirah Large with Shelf (Steel) (FD-1031, FD-1033, FD/E6/MAP/18) (Note : Second coat will be done after complete dried up of 1st coat as and when ordered and approval of 1st coat from GE

All as per item No 40.00 here- in -before but (b)Almirah Med Steel (FD-1032) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Table Clerk Steel ( FD-84 (M), FD-1004) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Table Officer Office Steel (FD-84(M), FD-1003) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Chair C B Steel with Arms (FD-75(M)) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Chair C B Steel without Arms (FD-75(M)) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Locker Bed side steel (FD-1029) complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Table Steel 900x900x760mm complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Table Steel 900x600x760mm complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but book case steel complete all as specified and as directed and as shown on drg.

All as per item No 40.00 here- in -before but Shoe rack steel complete all as specified and as directed and as shown on drg.

CHAIR EASY (FD-17M & FD-229) :- Taking out old damaged/decayed front leg from its position and S&F new front leg in the same position as per existing shape & size made out of well seasoned 'Teak wood' including providing hard rubber ring fixed with screws at the bottom of the leg including and applying two coats of high gloss polyurethane enamel paint by spray painting method over and including a coat of pink primer Complete all as specified and as directed

All as per item No 51.00 here-in-before but as in Rear Legs complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Side Rail of back frame complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Front Rail of seat frame complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Rear Rail of seat frame complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Back Rest complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Arms complete all as specified and as directed by Engr -in-charge

All as per item No 51.00 here-in-before but as in Stiffners complete all as specified and as directed by Engr -in-charge

CHAIR DINING (FD-16M & FD-279,FD/map-II/04): Taking out old damaged /decayed front leg from its position and S&F new front leg as per existing shape & size in the same position made out of well seasoned 'Teak wood' incl. hard rubber ring complete including with applying two coats of high gloss polyurethane enamel paint (Nerolac:Wonder Wood Coatings 1K PU Glossy/ Asian Paints:Wood Finishes Wood Tech Melamyne Glossy/ J&N Paints:Brolac Hi Gloss Polyurethane Enamel/ Berger Paints: Wood Finishes Imperia Luxuary Polyurathene High Gloss)by spray painting method over and including a coat of pink primer and prepration of surfaces Complete and as shown on drawing. (Make : KITPLY/GREENPLY/CENTURY

All as per item No 59.00 here-in-before but as in Rear Legs complete all as specified and as directed by Engr -in-charge

All as per item No 59.00 here-in-before but as in Side Rails complete all as specified and as directed by Engr -in-charge

All as per item No 59.00 here-in-before but as in Front Rails complete all as specified and as directed by Engr -in-charge

All as per item No 59.00 here-in-before but as in Rear Rails complete all as specified and as directed by Engr -in-charge

All as per item No 59.00 here-in-before but as in Back Rest complete all as specified and as directed by Engr -in-charge

All as per item No 59.00 here-in-before but as in Stiffners complete all as specified and as directed by Engr -in-charge

Peg Table(FD-277/384/236) :- (a) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 1st class teak wood free from all defects and with exposed wood surface painted with applying two coats of high gloss polyurethane enamel paint (Nerolac:Wonder Wood Coatings 1K PU Glossy/ Asian Paints:Wood Finishes Wood Tech Melamyne Glossy/ J&N Paints:Brolac Hi Gloss Polyurethane Enamel/ Berger Paints: Wood Finishes Imperia Luxuary Polyurathene High Gloss)by spray painting method over and including a coat of pink primer and prepration of surfaces Complete and as shown on drawing. (Make : KITPLY/GREENPLY/CENTURY

All as per item No 66.00 here-in-before but as in Leg of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 66.00 here-in-before but as in Side frame short Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 66.00 here-in-before but as in Side frame long Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

Table centre(FD-274,235,375):- (a) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with widht equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over including a coat of pink primer complete all as specified & as directed and as shown on drawing. (Make : KITPLY/GREENPLY/CENTURY )

All as per item No 70.00 here-in-before but as in Leg of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 70.00 here-in-before but as in Side frame short Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 70.00 here-in-before but as in Side frame long Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

Table 900x900x760mm (FD-(88),291): Taking out old damaged/decayed table top from its position and S&F new table top in the same position as per existing and size made out of 18/19 mm thick prelaminated particle board exterior grade having one side white balancing and other side mysore teak colour and providing teak wood beading all round including applying two coat of french polish over wood filler complete.

All as per item No 74.00 here-in-before but as in Leg of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 74.00 here-in-before but as in Top rail short of 1st class teak wood complete all as specified and as directed by Engr -in-charge

Taking out old damaged/decayed table top from its position and from Table 900x600x760mm with drawer and S & F Top of 18 mm thick pre-laminated particle board made to shape and size duly finished and polished complete and providing teak wood beading all round including applying two coat of french polish over wood filler complete as shown on drgs (FD-224/223) as specified and as directed by Engr-in-charge

All as per item No 77.00 here-in-before but as in Leg of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 77.00 here-in-before but as in short Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 77.00 here-in-before but as in long Rail of 1st class teak wood complete all as specified and as directed by Engr -in-charge

Side Board (FD-241):-(a) Taking down old existing unserciable/broken top and replacing the same with new top made out of 18/19 thick Medium Density Fibre (MDF) exterior grade ISI marked with exposed face covered with 1mm thick decorative laminates Type-I(ISI marked) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from defects complete all as specified & as directed and as shown on drawing

(b) Side Board (FD-241):-Taking down existing unserviceable back of side board replacing the same with new made out of 6 mm ply wood (5 ply) commercial BWR type BB. complete all as specified & as directed and as shown on drawing

(c)Side Board (FD-241)Taking down old existing unserviceable drawer and front shutter and replacing the same with new one made out of planks for drawer frame and 6mm plywood(5 ply) BWR type BB for bottom and 18/19 mm Medium Density Fibre (MDF) exterior grade ISI marked with exposed face covered with 1mm thick decorative laminates Type-I(ISI marked) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from defects complete all as specified & as directed and as shown on drawing

All as per item No 83.00 here-in-before but leg and replacing the same with new one made out of ist class seasoned hard wood complete all as specified & as directed and as shown on drawing

All as per item No 83.00 here-in-before but S&F of new Knobs for drawers complete all as specified & as directed and as shown on drawing

Table Dresssing Gents (FD - 230/379) : M&L for removing the existing broken / unserviceable mirror including preparation and S&F new mirror of 5 mm thick and 6 mm thick plywood for back including two coats of French Polish to all parts complete and as specified.

All as per item No 86.00 but as in S& F new drawers as shown on drawing

All as per item No 86.00 but as in removing the existing unserviceable eye hook and S&F new eye hook all as specified.

Chair Dining (FD/MAP-II/05) : Removing old unserviceaable PVC seat and S&F new PVC seat of approved quality as per existing specification as shown in drg and as specifed and directed by Engr-in-charge.

Supply and fixing of new tapestry cloth cover FOR 100 mm thick cushions of size 560x530mm x40 Density for seat/back of approved quality with zip facility (tapestry cloth not less than Rs. 250/- per RM) of approved quality and shade duly stitched as specified and directed by Engineer in charge (FD - 281/373)

Taking down unserviceabe mirror and replacing the same with new one of size 1220mm x 365mm x5mm thick make -modiguard/Atul/Golder fish and fixed with frame complete all as specified & as directed and as shown on drawing

Table Dining for 6 persons(FD-239/273):- (a) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over a coat of pink primer complete all as specified & as directed and as shown on drawing.

All as per item No 92.00 here-in-before but as in Leg of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 92.00 here-in-before but as in Top rail short of 1st class teak wood complete all as specified and as directed by Engr -in-charge

All as per item No 92.00 here-in-before but as in Top rail long of 1st class teak wood complete all as specified and as directed by Engr -in-charge

Table Computer (FD/E6/MAP/03 & TP) : M& L for removing old keyboard tray and S&F new keyboard tray made out of 18mm thick prelaminated paricle board to match with the original as shown on drawing

All as per item No 96.00 here-in-before but S&F new telescopic channel for keyboard tray/Draweras per existing specification and size to match the original complete all as specified as shown in drg and as directed.

All as per item No 96.00 here-in-before but M& L for tightening of loose and shaky joints of the main frame with metal L clamps

All as per item No 96.00 here-in-before but t S&F new PVC beading as existing specification as shown in drg

Replacement of unserviceable foam cushion,32 density, size 533x560x100mm thick for seat and back of Sofa set 5 seater S & F new one duly covering with inner cover with new marking cloth superior quality and new tapestry cloth on top as outer cover chain type and cost of tapestry cloth not less that Rs 350/- Per Meter (Make Sleepwell) as approved by GE complete all as per Drg (FD-281/373) and as directed by Engr-in-charge.

Replacement of unserviceable foam cushion,40 density, of any size S & F new foam cushion of chair Dining MAP of size 450X400X75mm thick 40 density foam with and including 12mm BWR plywood at bottom of seat for seat of duly covering with new tapesty cloth on top as outer chain type and cost of tapestry cloth not less that Rs 250/- Per Meter (Make Sleepwell) as approved by GE complete all as per Drg (FD/MAP-II/04) and as directed by Engr-in-charge.

BED HARD WOODEN(FD-213/212/245/246):Removing unserviceable foot rest portion of Bed Hard and S & F new foot rest 3.5/4mm thick one side teak faced and other side commercial BWR ply wood alongwith replacement of unserviceable wooden legs with well seasoned 1st class teak wood and providing readymade 30x4mm teak wood beading complete all as per DRG (FD-246) duly finished with french polish to all wooden surface exposed to view complete all as per specified and directed by Engr-in-charge.

All as per item No 102.00 here-in-before but Head Rest of Bed Hard complete all as per specified and directed by Engr-in-charge.

All as per item No 102.00 here-in-before but replacement of unserviceable long Rail of Bed Hard and S&F new long rail made out of seasoned teak wood duly finished with two french polish to all wooden surface exposed to view complete all as per specified and directed by Engr-in-charge.

Removing of unserviceable ply wood from the Head board and foot board of Bed Hard and S&F of new plywood with one side teak faced and other side commercial BWR to shape & size including provision of teak wood beading of size 30x4mm without disturbing to the teak wood frame complete all as per Drg(FD-245/246) or specified and directed by Engr-in-charge.

Removing the unserviceable ply wood top from bed Hard S&F new plywood 12mm thick BWR plywood 7 ply ISI Marked confirming to IS-303 of size 1840x910mm complete all as per Drg (FD-245/246) or specified and directed by Engr-in-charge. (Make Ecotec Green Ply or equivalent make as approved ) ISI Marked

M&L for removing the old existing unserviceable cane plastic from all kinds of chairs i.e. Chair Easy FD, Chair Easy JCO's, Chair dining, stool dressing CB, Couch CB two easy chair, Chair office CB, Bin soiled linen and recanning with new cane plastic 2mm wide as per Drg and 4mm wide shall be used for closing of border holes, complete all as specified and as directed by Engr-in-charge. Make:- Premier/AARYAN

Teapoy(FD-34,232/278):- (a) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of 2nd class hard wood of species TITACHAMPA/BONSUM/HOLLOCK free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over and including a coat of pink primer complete all as specified & as directed and as shown on drawing. (Make : KITPLY/GREENPLY/CENTURY )

All as per item No 108.00 here-in-before but leg and replacing the same with new one made out of Ist class seasoned hard wood complete all as specified & as directed and as shown on drawing.

All as per item No 108.00 here-in-before but long rail and replacing the same with new one made out of IST class seasoned hard wood and complete all as specified & as directed and as shown on drawing.

All as per item No 108.00 here-in-before but short rail and replacing the same with new one made out of Ist class seasoned hard wood complete all as specified & as directed and as shown on drawing.

Table writing(FD-249/275) :- (a) Taking down carefully existing unserviceable top of table and replacing the same with 18/19mm thick Medium Density Fibre board (MDF) exterior grade ISI marked (IS:12406-2003) with exposed face covered with 1mm thick decorative laminates Type-I ISI marked (IS:2046-1995) of surface finish colour and pattern as approved, affixed with synthetic glue and exposed edges provided with 4mm thick edging with width equal to thickness of board of Ist class hard wood of species teak free from all defects and with exposed wood surface painted with two coats of high gloss polyurethane enamel paint over a coat of pink primer complete all as specified & as directed and as shown on drawing.

All as per item No 112.00 here-in-before but leg and replacing the same with new one made out of ist class seasoned hard wood complete all as specified & as directed and as shown on drawing

All as per item No 112.00 here-in-before but long rail and replacing the same with new one made out of ist class seasoned hard wood complete all as specified & as directed and as shown on drawing

All as per item No 112.00 here-in-before but short rail and replacing the same with new one made out of ist class seasoned hard wood all as per drawing and as directed.

Complete removal of existing painting/polish and applying two coats of high gloss polyurethane enamel paint (Nerolac:Wonder Wood Coatings 1K PU Glossy/ Asian Paints:Wood Finishes Wood Tech Melamyne Glossy/ J&N Paints:Brolac Hi Gloss Polyurethane Enamel/ Berger Paints: Wood Finishes Imperia Luxuary Polyurathene High Gloss)by spray painting method over and including a coat of pink primer and prepration of surfaces Complete all as specified and as directed all as per specified in the Drg (FD-246) bed hard and as directed by Engr -in-charge.

All as per item No 116.00 here-in-before but Table Writing , complete all as per specified in the Drg (FD-33(M) 375/249)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Chair Dining , complete all as per specified in the Drg (FD-279)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Chair Easy , complete all as per specified in the Drg (FD-229)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Chair writing , complete all as per specified in the Drg (FD-220)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Sofa set 4 and 5 seater , complete all as per specified in the Drg (FD-373/281)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Side Board , complete all as per specified in the Drg (FD-241)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Teapoy , complete all as per specified in the Drg (FD-282) and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Stool dressing , complete all as per specified in the Drg (FD-398)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Peg Table, complete all as per specified in the Drg (FD-273)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table dressing Gents, complete all as per specified in the Drg (FD-230)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table dressing ladies, complete all as per specified in the Drg (FD-230)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table Centre, complete all as per specified in the Drg (FD-274)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table dining 6 person, complete all as per specified in the Drg (FD-30M)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table 900x900x600MM without drawer, complete all as per specified in the Drg (FD-284)and as directed by Engr-in-charge.

All as per item No 116.00 here-in-before but Table 900x600 with drawer, complete all as per specified in the Drg (FD-285)and as directed by Engr-in-charge.

Removing existing Nylon Newer from CHARPOY GI PIPE and providing new stiffener of size 25X25mm Square Tube 16 Gauge 6’ long, cut into proper Sizes and Shape of Stiffeners (02 No. 850mm Long) and Welded to Long Rails, perpendicular to the long rails at equal distance, providing 06 Nos (03Nos for each short rail) 6mm thick MS Cleat of size 25x60mm welded to short rail to support ply including drilling holes (02 Nos in each Stiffener and o1 No in each cleat) supply and fixing Ply-wood of Size 1980X900X12mm thick, Commercial grade (07 ply) ISI Marked with beading all around, 10 Nos galvanised countersunk nut andt Bolt of suitable size and length, 02 Nos washer for each nut and bolts including applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer to Stiffeners and cleats, complete all as specified and as directed.(Drg No FD-220).

S&F GI Charpoy Long Rail of GI Pipe 32mm Bore (dia) Medium Grade duly threaded both ends upto the required Length and fitted to frame of Charpoy including taking out unserviceable long rail from 3-way elbow by unscrewing, complete all as specified/as shown on Drawing/as directed.(Drg No FD-220).

Making GI Charpoy Short Rail to be made out from Long Rail (Retrieved from item No 133 here-in-before), duly cut and threaded both ends upto the required length and fixing including Taking out unserviceable SHORT RAIL by unscrewing from 3 Way Elbow, complete all as specified/as shown on Drawing/as directed. (Drg No FD-220).

Making GI CHARPOY LEG to be made out from LONG RAIL & SHORT RAIL (Retrieved from item No 133 & 134 here-in-before), duly cut and threaded one End including and providing 3mm thick Mild Steel Flat iron 55mm dia Welded to bottom of the Leg and fixing including treating with two coats of black paint over a Coat of Red Oxide Zine Chrome Primer including Taking out unserviceable LEG by unscrewing from 3 way Elbow, complete all as specified/as shown on Drawing/as directed.(Drg No FD-220).

S&F GI ELBOW 3-WAY, ISI Marked suitable for GI Pipe 32mm Bore (dia) of GI CHARPOY including Taking out unserviceable GI ELBOW from the Frame, complete all as specified/as shown on Drawing/as directed.

S&F GI CHECK NUT, ISI Marked suitable for GI Pipe 32mm Bore (dia) of GI CHARPOY including Taking out unserviceable GI Elbow from the Frame, complete all as specified/as shown on Drawing/as directed.

S&F 3mm thick Mild Steel Flat iron 55mm dia Welded to bottom of the Leg and treating with two coats of black paint over a Coat of Red Oxide Zine Chrome Primer including Taking out unserviceable LEG by unscrewing from 3 way Elbow, complete all as specified/as shown on Drawing/as directed.

M/S C C CONSTRUCTION

SUMAN CONSTRUCTION