Provn of certain Special Repair, Revenue and Minor Work under AGE B/R-II under GE Kapurthala

Amount

Surface excavation not exceeding 45cm deep and averaging 30cm deep and getting out in soft/loose soil, including removal of excavated earth upto a distance 500m from starting point complete all as specified and directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth not exc 10 sqm on plan, for foundation/foundation of poles/stays/laying of cables etc and getting out in soft / loose soil complete all as specified and as directed by Engr-in-Charge.

M&L for Hardcore of broken stone or boulders of gauge not exceeding 63mm, deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete or as in sub base of floors complete all as specified and directed by Engr-in-Charge.

M&L for cement conrete nominal mix (1:1.5:3) using 20 mm graded crushed stone aggregate as in base course of hard standing etc complete all as specified and as directed by Engr-in-Charge.

M&L for stone sett flooring with stone setts of size 200 to 250 mm long, 150 to 200 mm wide and 150 mm deep and sides dressed, bedded in cement mortar 1:2 mixed with an admixture of metalic floor hardner 5% by wt of cement and struck flush complete all as specified and as directed by Engineer-in-Charge.

M&L for edge stone to flooring with stone setts of size 250 to 300 mm long x 150 to 200 mm wide and 450 mm deep and sides dressed, bedded in cement mortar 1:2 mixed with an admixture of metalic floor hardner 5% by wt of cement and struck flush complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced concrete 450mm dia pipe class NP-3 laid & jointed with collars complete all as specified and as directed by Engineer-in-Charge.

M&L for plain cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for cement concrete (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in bed of RCC NP-2 pipe of 200mm bore including packing under and haunching against the sides of pipes after laying and testing complete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregates as in sub base of floor complete all as specified and as directed by Engineer-in-charge.

M&L for 25 mm thick cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in floors finished even & smooth without using extra cement complete all as specified and as directed by Engineer in charge.

M&L for 40 mm thick cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in DPC and Copings, finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc drilled for fixing of steel sheeting or other covering to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging including fastening and fixing complete all as specified and as directed by Engineer-in-Charge.

M&L for mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and as directed by Engineer-in-Charge.

M&L for Reinforced concrete 200 mm dia pipe class NP-2 laid & jointed complete with collars complete all as specified and as directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 450x300x7mm thick set and jointed in neat cement slurry pointed in white or colour cement to match the colour, with 10 mm thick rendering in CM (1:4) including dismantling existing tile and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L for vitrified ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tile not exc 0.36 Sqm in floor, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including 15 mm thick cement screed bed in CM (1:6) including dismantling the existing tiles and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M&L for vitrified ceramic tiles light shade tiles 10 mm thick (square/rectangular) polished, area of each tile not exc 0.36 Sqm in vertical surface such as skirting dados and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles, with 10 mm thick rendering in CM (1:4) including dismantling of existing tile and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exc 0.18 Sqm in floor set and jointed in neat cement slurry and pointed in white or colour cement to match the shadeof tiles, with 15 mm thick cement screed bed in CM (1:6) including dismantling the existing tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge

M&L for Granite of thickness 20mm (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling of existing surface of any type and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for rounding to edges of granite stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed by Engineer-in-Charge.

M&L for machine cut Kota stone of 18-20mm thick as in flooring, staircase, cooking platform etc laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing including 15mm thick bedding layer in CM 1:6 complete all as specified and as directed by Engr-in-Charge.

M&L Machine cut Kota stone slab 18-20mm thick in riser pf steps, skirting, dado over cement screed base laid and jointed with grey cement slurry mixed with puigment to match the shade of the slab including rubbing and polishing bedded on 10mm thick bedding layer in CM 1:4 as specified and directed by Eng-in-Charge

Demolition of brick / block masonry built in CM including all quoins, arches, pillars etc and clearing off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge.

M&L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges to rough finished surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending hooking etc & binding with mild steel binding steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by Engr-in-Charge.

M&L for RCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in chajjas, manhole cover, tank platform etc complete all as specified and as directed by Engineer-in-charge.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in surface channel and benching for manholes and haunching around manholes frames including necessary formwork and finishing exposed surfaces even and smooth without using extra cement complete all as specified and as direted by Engr-in-Charge.

M&L for raking out joints and pointing to brick work in wall or to brick on edge built in cement mortar (1:3) etc complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster on brick work or concrete surfaces incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm thick on brick wall or concerte surface in CM 1:4 with water proofing compound @ 3% of weight of cement or as per manufacturer instructions finished even and fair etc complete all as specified and as directed by Engr-in-Charge. Note :- WPC shall be measured and paid separately.

M&L for 10mm thick rendering in CM 1:3 on brick work or concrete surfaces finished even and smooth without using extra cement in ceiling etc complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of whitewash on ceiling over a coat of 1.00mm thick white wall care putty complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distermper over a coat of 2.00mm thick white wall care putty including appropriate primer complete all as specified and as directed by Engr-in-Charge.

M&L for Preparation of new plastered or unplastered decorated surfaces of walls or cornics by applying water and scrapping using steel scraper and thereafter applying two coats of exterior emuslion paint over and including 2mm thick wall care putty to achieve smooth finish over a coat of appropriate primer complete all as specified and directed by Engr-in-Charge. Note- Exterior emulsion paint to be done by Roller.

M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces of ceiling and applying three coats of whitewash complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces of walls and applying one coat of oil bound distermper complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of old plastered or unplastered decorated surfaces of walls or cornics by complete removeal of existing treatment by applying water and scrapping of entire thickness of exsting treatment with using steel scraper and thereafter applying two coat of exterior emuslion paint and including 2mm thick wall care putty to achieve smooth finish over a coat of appropriate primer complete all as specified and directed by Engr-in-Charge. Note- Exterior emulsion paint to be done by Roller.

M&L applying two coats of cement base paint on old plastered or unplastered wall surface including preparation of surfaces, complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6 type C2 as in plinth protection finishing the surface even and fair complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area not exc 1.50 sqm each complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats or framed with shutter (with out taking off shutters from the frame) area exc 1.50 sqm but not exceeding. 4.0 sqm each complete all as specified and as directed by Engr-in-Charge.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed by Engr-in-Charge.

S&F factory made solid Panel PVC moulded door shutter with particle board core 28 to 30mm thick (stiles) with 2, 4 or 6 raise panel design with 2mm thick moulded pvc sheet on the front face and 2mm plain colour pvc sheet on back face supplying and fixing in frame at site as per specification complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel conforming to Fe-290, Gde-E-165 framed work as in door frames, chowkhats including necessary cutting, welding, bending, drilling etc complete all as specified and as directed by Engr-in-Charge.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete, as specified, size of frame 125 x 60mm filling hollow frame all as specified and directed by Engineer-in-Charge.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete, as specified, size of frame 105 x 60mm filling hollow frame all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:3:6 type C2 as in filling of steel chowkhats of any size complete all as specified and directed by Engr-in-Charge.

S&F factory made 2nd class, hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars any numbers sizes of members of shutters complete all as specified and as directed by Engr-in-Charge.

S&F PVC cupboard of size 75mm x 40mm with wall thickness of 5mm made out of extruded 5mm thick Plain/Printed/Prelam PVC sheet reinforced with 15mm x 15mm M.S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners and jointed with 2 nos. of 150mm long brackets of 10mm x 10mm M S square tubes. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasteners complete all as specified and as directed by Engr-in-Charge.

S&F in repair 2nd class hardwood clean swan with butt joints 20mm thick board in shelves, partitions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work complete all as specified and as directed by Engineer-in-Charge.

S&F factory made solid Panel PVC moulded door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet 10mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed by Engineer-in-Charge.

S&F factory made PVC cupboard shutter flush type of 25mm thickness consisting of panel of hollow PVC profile of 12mm x12mm inserted all around the hollow profile section and insert one 10mm x 10mm MS tube in the centre of this section and lipped with 10mm thick(5mm x 2) and 12mm wide on stiles and rails using solvent cement the inner panel shall be laminated with 5 mm thick termite proof waterprrof and fire retardent printed PVC sheet using solvent cement on both sides of panel complete all as specified and as directed by Engineer-in-Charge.

S&F factory made 2nd class hard wood Plain, framed, panelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed by Engineer-in-Charge.

S&F alumunium hinges for PVC door shutter, size of hinges in 100mm complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt in 200mm complete all as specified and as directed by Engineer-in-Charge.

S&F mild steel barrel tower bolt, stove enamelled black, with bright bolt of 150mm size complete all as specified and as directed by Engineer-in-Charge.

S&F mild steel pressed handle , oval type stove enamelled black of size 125mm complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Floor door stopper of aluminium alloy body and tongue, anodised, Overall length of cover plate 140 mm , with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs of size 300mm MS ordinary rat rail rod pattern helical springs including roller and roller plate complete all as specified and as directed by Engineer-in-Charge.

S&F extruded aluminium alloys handles frabicated type anodized of size 150mm long complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 250mm complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new wooden surface exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old steel surfaces of any description over 10cm girth or width not otherwise described and applying two coats of synthetic enamel paint all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm girth or width not otherwise described and applying two coats of synthetic enamel paint over red oxide primer all as specified and directed by Engineer-in-Charge.

S&F steel window 1.25mm thick Box type (primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Handles of Z Sec 20mm x 100mm long (b) stopper – 01 No per leaf (c) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (d) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (e) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note: Glass and painting shall be measured and paid separately under appropriate item (ii) Irrespective of whatever shown on drgs, MS gills shall be of 12mm dia MS square bar and paid separately.

M&L for framed work such as grills gratings etc with ends of bars shouldered and or riveted or forged into spikes framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framed work of water tanks and similar work coforming to Fe 290 Gde E-165 complete including taking down complete all as specified and as directed by Engineer-in-Charge.

S&F steel window 1.25mm thick Box type (primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf. Note: Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and as directed by Engineer-in-Charge.

S&F steel ventilators fixed type with glazing bars etc complete all as specified and as directed by Engineer-in-Charge.

S&F 4.00mm thick sheet glass, ordinary quality in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and as directed by Engineer-in-Charge.

S&F 4.00mm thick figured glass, pinhead type in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and as directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperture 1.00mm and fixed with tinned tacks/screws with bolts incl leaping wooden complete all as specified and as directed by Engineer-in-Charge.

Dismantling of cast iron pipe any diameter jointed with cement mortar or lead incl all fittings from wall or floors complete all as specified and as directed by Engineer-in-Charge.

Taking down GI tubing & connection 15mm dia laid in floor / trenches or fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge.

Taking down GI tubing & connection 20mm dia laid in floor / trenches or fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F GI tubing 20mm dia medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge.

S&F wash hand basin mixer 15 mm Brass CP for mixing hot and cold water with all necessary fittings screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F wall mixer 15 mm Brass CP for mixing hot and cold water with all necessary fittings , screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 15 mm bore CP bib taps fancy type cast copper alloy with crutch or butter fly handle screwed down for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 15mm dia stop/angle valve, CP cast copper alloy with crutch or butterfly handle. Screwed down high pressure, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F PVC connection fibre reinforced 450 mm long, 15mm size with brass check nuts complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs vitreous china squatting pan Orissa pattern wash down water closet of size 580x440 mm, white, with integral foot rests complete fixed in repairs with P or S trap, PVC flushing cistern low level of Make 10 ltrs capacity including brackets for flush tank, PVC flush pipe and all necessary fittings etc complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern) of white colour including plastic water closet seat back closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, P or S trap, jet spray necessary inlet and outlet connections including syphonic action type low level PVC flushing cistern of 10 lit capacity make white in colour and PVC flush pipe 32mm dia complete all as specified and as directed by Engineer-in-Charge.

S&F 20mm dia aluminium chromium plated tubular towel rails,D type, 60cm long between flanges, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs PVC(SWR) floor trap with grating and diameter of outlet 75mm including jointing to waste pipe fixed with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs fancy type chromium plated stop valves with long shank and cup (concealed type) cast copper alloy screweddown high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed for bore fof size 15mm complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs for vitreous china ware wash basin white, flat back size 550 X 400mm including 15mm dia pillar tap chromium plated, CP waste coupling, waste fittings, union and waste pipe 32mm dia or required length and all necessary inlet, out let connections complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs shower rose 125mm with cp arm of chromium plated any colour or fixing with 15mm pipe (minimum weight 40gm) complete all as specified and as directed by Engineer-in-Charge.

S&F in repair kitchen sink with drain board made of stainless steel 1mm thick sheet with plugs, washers and wastes including bedding in cement mortar including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer-in-Charge.

S&F utensil rack stainless steel of size 750x600x250 mm fixed on walls with screws complete all as specified and as directed by Engineer-in-Charge.

S&F soap dish chromium plated heavy duty complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 25mm dia MS curtain rod powder coated with fixing bracket and end stops complete all as specified and as directed by Engineer-in-Charge.

Cutting chases pinning in brick/stone/blocks masonary in making good to facings where required and pointing in CM (1:3) to ends or eges of steps, cills, sun shades, shelves, lintel etc and cutting chases for concealed water tubing or etc and making good complete all as specified and as directed by Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes including all fittings complete all as specified and as directed by Engineer-in-Charge.

Dismantling of cast iron pipe any diameter jointed with cement mortar or lead incl all fittings from wall or floors complete all as specified and as directed by Engineer-in-Charge.

S&F 75 mm UPVC pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F 75 mm UPVC pipes in repair single socketed in any length laid in floor complete all as specified and as directed by Engineer-in-Charge.

S&F 75 mm UPVC bend complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm UPVC junction single, (single T) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

S&F 110 mm UPVC pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F 110 mm UPVC bend with complete all as directed by Engineer-in-Charge.

S&F 110mm UPVC junction single,(single T) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm UPVC vent cowl complete all as specified and as directed by Engineer-in-Charge.

Dismantiling water tank PVC 500 Ltrs and removing from site complete all as specified and as directed by Engineer-in-Charge.

Dismantiling water tank PVC 1000 Ltrs and removing from site complete all as specified and as directed by Engineer-in-Charge.

S&F rotational moulded polythelene water storage tanks (three layered) cylindircal water tank for hoisted and fixed in postion as specified in SSR Part-I of 1000 ltrs capcity incl fittings complete all as specified and as directed by Engineer-in-Charge.

S&F rotational moulded polythelene water storage tanks (three layered) cylindircal water tank for hoisted and fixed in postion as specified in SSR Part-I of 500 ltrs capcity incl fittings complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Ball brass valves 15 mm bore high pressure with polythene float and fly nuts complete, screwed for iron pipe complete all as specified and as directed by Engr-in-Charge.

S&F in repair gunmetal globe and gate valve with iron welded hand secrewed both and for iron pipe 20mm bore complete all as specified and as directed by Engr-in-Charge.

S& F in repairs Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 25mm-455gms complete all as specified and as directed by Engr-in-Charge.

Dismantling of brick tiles or terracing tiles laid bedded and pointed in cement mortar in single layer on roofs complete all as specified and as directed by Engr-in-Charge.

Demolition of mud in roof any thickness including plastering & leeping including removal from site complete all as specified and as directed by Engr-in-Charge.

M&L for 15mm thick screed bed or bedding layer of mortar for roof and floor finishes in Cm 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 10mm thick cement mortar 1:3 on concrete surface even and smooth with waterproofing compound complete all as specified and as directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of newly plastered surface making surface completely dry, M&L for bitumen primer @ 0.30kg/sqm, after drying of primer apply APP modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymericweighing not less than 3kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene (MHHDPE) film consisting of five layers with a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm under the APP membrane laid with torching application to the surface complete and sealing the side as well as end laps (overlaps should not be less than 10 cm) complete all as specified and as directed by Engr-in-Charge.

M&L for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under:- (a) Application of Two component acrylic modified cementitious coating. (i) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil surface treatments and old coatings. Concrete sufraces must be mechanically prepared using abrasive blast cleaning or milling to remove cement litance, existing coatings and achieve a gripping profile that is clean, dry and free from litance and any other form of surface contamination. the installation instructions in manufacturer's published literature should be strictly compiled with, including but not limited to the following:- (ii) Chipping out any visible cracks in ' V- Groove' pattern as applicable. Special attention on this part cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putyy/ Dr Fixit 302 SBR latex/ perma latex SBR / FOSROC Nitibond SBR latex/ Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush and vaccum pressure if required. (iii) Dampen all surfaces immediately ahead of application of Acrylic modified cemetitious coating of Sika Top seal - 107/brush Bond FOSROC/ Dr Fixit/ STP/ CICO. (iv) Whilst the surface is still damp from saturation (SSD), apply one coat of acrylic modified cementitious coating of Sika Top seal- 107/ Brush bond FOSROC/ Dr fixit / STP/ CICO of viscosity as per manufacturer's instructions. (v) Apply glass fabric sheet of Sika Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet. (vi) Once touch dry apply second coat of Acrylic modified cementitious coating of Sika Top Seal- 107/ Brush bond FOSROC/ Dr FiXit/ STP/ CICO of viscosity as per manufacturer's instructions on the entire area. (vii) Second coat shall be applied after 6-8 hrs of application of previous coat and in the direction right angle to the previous coat. (viii) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surface. (ix) It is essential to cure acrylic modified cementitious coating immediately after application (minimum 6-8 hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (x) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls.

Admixture: -Sika Plastocrete plus/FOSROC Dr Fixit/STP/CICO confirming to IS 2645. (xi) Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika plastocrtete over the applied water proofing coating on horizontal surfaces. Admixutre:Sika Plastocrete Plus/ FOSROC/ Dr Fixit/ STP/ CICO confirming to IS 2645. (xii) All the corners and joints should be pre-treated with elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (xiii) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (xiv) waterproofing treatment has to be carried out. (b) All the joints of pipes and traps within sunken portion shall be sealed properly by Epoxy sealant. (c) All CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) all round. (d) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified. (e) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (f) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm grade stone aggregate as in flooring for laying floor finish all as specified. Note :- Item No 125 (d), (e) & (f) shall be measured and paid separately under revelent item.

M&L for cement concrete 1:5:10 type E-2 (using 40mm stone aggregate) as in sub base/sunken flooring complete all as specified and directed

S&F drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish complete all as specified and directed

M&L for 40mm thick brick tiles laid on 15mm screed bed in cement mortar 1:3 with jointing and pointing in cement mortar (1:3) mixed with 5% crude oil by weight of cement all as directed.

All as per item no 129 above but except brick tiles complete all as specified and directed by Engineer-in-charge.

M&L for 40 mm thick Cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in PCC padding over roof slab complete all complete all as specified and as directed by the Engineer-in-Charge.

M&L for cement concrete Type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs, rounded or chamfered edges complete all as specified and as directed by Engr-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658- 2006 of 60mm thickness, M-35 grade with grey cement and pigment over sand cushioning complete all as specified and as directed by Engr-in-Charge. Note : Sand cushioning will be measured and paid seperately.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658- 2006 of 80mm thickness, M-40 grade with grey cement and pigment over sand cushioning complete all as specified and as directed by Engr-in-Charge. Note : Sand cushioning will be measured and paid seperately.

M&L for 25mm Fine sand filling under floor or in foundations in layers including watering and consolidation complete all as specified and as directed by Engr-in-Charge.

M&L for demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-Charge.

S&F Continuous (piano) hinges, mild steel, bright finish or eletro galvanised complete all as specified and as directed by Engr-in-Charge.

S&F Magnetic catcher for shutter of approved pattern fitted with suitable screw complete all as specified and as directed by Engr-in-Charge.

S&F 18mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed by Engr-in-Charge.

S&F 5mm thick 18mm wide wooden fillet for beading purpose of cupboard shutter including necessary nails screws etc complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium handles,100mm long cast type, anodised complete all as specified and as directed by Engr-in-Charge.

Demolition and breaking up 200mm bore dia drain pipe (salt glazed ware, AC or reinforced cement concrete) set in cement concerte complete all as specified and as directed by Engr-in-Charge.

M&L for Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed by Engr-in-Charge.

M&L for concrete bed to drain pipes 200mm bore in cement concrete (1:3:6) type D-2 (using 20mm graded stone aggregate) including packing under and haunching against sides of pipe after they are laid and tested complete all as specified and as directed by Engr-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by Engr-in-Charge.

Removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5m as in soil complete all as specified and as directed by Engr-in-Charge.

M&L for RCC Septic tank conventional designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls, Base Slab, Baffle walls and Roof Slab including beams etc with Vent shaft, manhole openings with cover connection etc, complete with effective depth of 1.5 meter and overall depth of 3 meter for 50 users complete all as specified and as directed by Engr-in-Charge.

M&L for Soakage well excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 3.0 m dia X 4.50 m effective depth (DRG No CEJZ/STD-242/07 sheet No 1/24 to 24/24) complete all as specified and as directed by Engr-in-Charge.

M&L for Precast cement concrete block masonary with solid block (size 30x20x10cm) as in edging, type B-1, (1:2:4) (20 mm graded aggregate) exc 10 cm in width and setting in mortar 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel expended metal cut to length, bent to shape required and tying with and including annealed mild steel wire galvanised, steel staples and fixed to wood or steel members, weight not exceeding 4 kg per sqm complete all as specified and as directed by Engr-in-Charge.

Taking down aluminium point wiring for light, fan, bell socket, power socket etc complete including fittings and fixtures removing from site and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC (FRLS) insulated cable in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.5 Sqmm insulated un-sheathed PVC insulated copper conductor common earth and connecting to earth dolly for :-

(a) One light point controlled by one, one way switch

(b) One fan point controlled by one, one way switch

(c) One socket outlet 3 Pin, 5 Amp on independent board

(d) One socket outlet 3 Pin, 5 Amp on same board.

(e) One bell point controlled by one bell push

(f) One light point controlled by two 2 -way switches

M&L for point wiring with 2.50 Sq mm single core multi-stranded copper conductor PVC (FRLS) insulated, unsheathed cable 1100 volt grade in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.50 Sq mm single core, multi-stranded copper conductor, PVC insulated, unsheathed cable for common earth and connecting for earth dolly for 5 pin, 15 Amp socket outlet on Independent board complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring with 4.00 Sq mm single core multi-stranded copper conductor PVC (FRLS) insulated, unsheathed cable 1100 volt grade in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.50 Sq mm single core, multi-stranded copper conductor, PVC insulated, unsheathed cable for common earth and connecting for earth dolly for 5 pin, 15 Amp socket outlet on Independent board.

S&F switch piano flush type single pole one way 5 Amp (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F Bell push flush type single pole one way 5 Amp (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type single pole two way 5 Amp complete all as specified and as directed by Engr-in-Charge.

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

M&L for bell multi music type, AC 230 Volts, single pole (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable flourescent tube light fitting 36/40 watt fluorescent tube light fittings direct to walls or roof as ordered and disconnecting electrically with the electrical system and all materials required for the same. The rates also include making good the same to match with the existing surface complete all as specified and as directed by Engr-in-Charge.

Supply, installation, testing and commissioning of 20 watt 4 ft long LED Batten housing made of extruded alluminium with milky white diffuser and inbuilt electronic driver system lumen output should be at least 1800 lumen with a CCT of 6000 K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 complete all as specified and as directed by Engr-in-Charge. Make : Polycab Cat part No PCGLB AX 2060 or equivalent in Philips/Bajaj/C&S electric/Surya

Taking down old unserviceable wall mounting fitting & supply & fix decorative wall mounting type made up of polycarbonate rings, and glass shade with lamp holders, connectors block, 1 x 09 watt LED Blub,glass fitted engineering plastic B22 d lamp holder with electrical copper contactcs, self screwed polycarbonate diffuser in opal finish for soothing light effect, LED 09 watt etc complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and as directed by Engr-in-Charge. Cat part No LHDL03160099 of make Havells or equivalent in bajaj & philips.

S&F LED Bldg security light fitting 35 W housing made out of die cast aluminum alloy with toughed glass, IP 65/66 protection having clamp for mounting on wall working on 240 V AC 50 Hz, 20 watts including fixed on wall with 02 Nos MS clamps and bracket made of 40 mm dia light grade GI pipe bend to shape complete all as specified and as directed by Engr-in-Charge. Make : Wipro/Havells/Bajaj.

Taking down old unserviceable lamp holder and S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED lamp 09W complete all as specified and as directed by Engr-in-Charge.

Taking down old unsv DB and supply and fixing factory made sheet metal enclosure double door distribution board class IP-43 with 200 Amp rated copper bus bar 240 volts 8 way single pole and neutral link complete all as specified and as directed by Engr-in-Charge.

Taking down unserviceable MCB’s and supply & fix following type/rating MCB’s including necessary connection as under:-

(a) MCB, 10 to 32 Amp, SP, 240 Volt. Make - Legrand/Schneider-Acti 9/Siemens-Betagard

(b) MCB, 25 to 32 to Amp, SPN, 240 Volt. Make - Legrand/Schneider-Acti 9/Siemens-Betagard

M&L for sub main wiring with two runs of single core PVC insulated, unsheathed copper condutor, multi stranded cable of size 6.00 Sqmm 1100 volts grade drawn PVC concealed conduit of size 19/20 mm (ISI marked) including PVC accessories complete incl cutting and chasing and making good etc including one run of 6.00 Sqmm single core copper conductor multi-stranded PVC insulated, unsheathed cable as earth wire continuity conductor complete all as specified and directed by Engineer-in-Charge. Note : Three run of 6.00 Sqmm cable and one run of PVC Conduit shall be measured & paid as one unit.

S&F in replacement Exhaust fans of 230 Volt 300 mm sweep ventilator DB bouble ball bearing heavy duty motor, metal blade with protection steel bird guard and roubst complete including M&L for providing/cutting the round hole of required size in wall finishing the same supply and grounting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 23/.0076 copper cable rubber insulated from ceiling rose to exhaust fan motor and writing MES No. with black synthetic enamel paint 2.0 cm high complete all as specified and as directed by Engr-in-Charge. (Make : BAJAJ, HAVELLS, USHA)

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engr-in-Charge.

S&F water heater storage type electric, capacity 25 litres BEE 5 star BEE rating AC 230 volts, 50 Hz vertical type including material and labour for grouting four Nos rack bolt for holding of water heater on wall including making good and match existing surfaces and complete all as specified and as directed by Engr-in-Charge.

Supplying, laying, jointing and testing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 Sqmm 3 and half core laid in trenches, in floor, in duct, through pipes or along the pole including taking down old one complete all as specified and directed by Engr-in-Charge.

Supplying, laying, jointing and testing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 vols grade cross sectional area 16 Sqmm 2 core laid in trences, in floor, in duct, through pipes or along the pole including taking down old one complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning to under ground cable with a layer of sand 8 cm thick before laying of cable and 15 cm thick after laying of cable complete all as specified and as directed by Engr-in-Charge.

M&L for brick protection using old size sub class ‘B’ bricks, laid flat, dry adjacent to each other laid length wise perpendicular to the axis of cable complete all as specified and as directed by Engr-in-Charge.

SUNRISE ENGINEERS AND CONTRACTOR (BID ID -3166428)

COSMO BUILDERS (BID ID -3165711)