REPAIRS TO PLASTERING, JOINERY, SANITARY FITTINGS, WALL PANELLING, PERIODICAL SERVICES AND MISCELLANEOUS WORKS AT PEDONG, ALGARAH, DALAPCHAND, AP ALGARAH AND TEESTA TCP UNDER GE 867 EWS

Amount

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 including demolition of existing block masonry complete all as specified and directed by Engineer-in-charge. Make: Shankar Saw Mills/Sangam Prefeb Products

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including Integral waterproofing compound @ 3% by weight of cement as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement including taking down cement plaster on brick or stone masonry surfaces of walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including Integral waterproofing compound @ 3% by weight of cement as per manufacturer's instructions including taking down cement plaster on brick or stone masonry surfaces of walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. Make: LOVELYCEM/ SURYACEM/ JANATHACEM / LUCKYCEM or equivalent make as approved by GE.

M&L for preparing newly plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of primer over thin layer of wall care putty (Birla white/Berger/Asian) complete all as specified and as directed by Engineer-in-Charge. Make: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON/IEL

S&F 15mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete including short lengths including taking down existing GI pipe complete all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F in repairs bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge.

S&F Pillar taps fancy type 15 mm bore, cast copper alloy, chromium plated with crown or capstan head screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, fixed in repairs, all as specified and directed by Engr-in-Charge.

S&F in repairs Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, concealed type with long shank ang cup screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge. Make for Item No. 9 to 11: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F in repairs PVC connection pipe 15mm dia, 600mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F PVC valveless, symphonic action type, flushing cistern 10ltr capacity, low level, white with inlet ball valve float and handle along with suitable flush pipe/bend including brackets fixed in repairs complete all as directed by Engr-in-Charge. Make: PARRY WARE (SLIMLINE)/ COMMANDER/ HINDWARE

Taking down existing IWC along with its cement concrete bedding and P or S trap and S&F Orrissa pattern vitreous china squatting pan white colour of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including cement concrete bedding and P or S trap as required including PVC pipe upto finished floor level to connect flush pipe, making good all the disturbed surfaces of floor to match the adjoining complete all as directed by Engineer-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Vitreous china wash down water closet pan (pedestal pattern) white, excluding flushing cistern and flush pipe but including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including taking down existing unserviceable/broken EWC complete all as specified and directed Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Vitreous China wash basin, white, flat back, of size 550x400 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 40mm dia brass chromium plated waste fitting and 40mm dia 90cm long PVC waste pipe, including taking down existing unserviceable/broken wash hand basin all as specified and directed by Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm (minimum), white with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as directed by Engr-in-charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 75mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F in repairs PVC (SWR) bends (any radius) suitable for 110mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) bends (any radius) suitable for 75mm bore pipe fitted with access door complete all as directed by Engr-in-charge. Make for item No 18 to 21: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK/SUPRIME

S&F in repairs chromium plated health faucet, fancy type, ABS SS braided hose 1m long with hook, screwed to iron pipe all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.5 Sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as specified and as directed.

S&F second class hardwood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid ,rounded or chamfered put together with glue pinned joints all as specified and directed. TIMBER: - Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F 105x60 mm size pressed steel door frame for doors made of 1.25mm sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC 1:2:4 type B0 filling complete all as directed by Engr-in-Charge. Make: -B A Enterprises/Multiwyn/Doorwyn/Modern fabricator/Madhu industries/Ajanta Ispat/Alusys or equivalent as approved by GE.

S&F 30mm thick factory made flush shutters, solid core construction with block board core and plywood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-Charge. Make: - Green Ply/Archid Ply or equivalent as approved by GE.

S&F Anodised aluminium frame for partitions, doors, windows ventilators with one or more rebates, grills including joining cleat for fixing etc., complete all as specified and dierected by Engr-in-Charge.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handels 2 Nos in each door, 1 no mortise lock per each door, hinges, anodised alumnium snap beading, screws etc., with and including 5mm thick plain glass as panel insersts complete all as specified and directed. Make for Item No. 31&32: JINDAL/INDALCO/HINDALCO

M&L Preparing surfaces of wood and wood based materials, steel and iron work , new or old, of any description not otherwise described exceeding 0.10 Sqm and not exceeding 0.50 Sqm each, and treated with tar or coal tar black paint all as specified and directed.

M&L Mild steel work such as bands, straps, clamps and hold fasts etc. of Fe-290 Gde E-165 all as specified and directed.

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing. Make for Item No. 35 & 36: - SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F 30mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of 12mm thick timber flat on both sides or of 12mm thick veneered particle board ,medium density, wood particle board with commercial face veneers with sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified directed by Engr-in-charge.

S & F 30 mm thick second class hard wood Glazed and skeleton shutters for doors, open rebated and prepared to receive glass,gauze etc., edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats all as specified and directed. Timber for item Nos. 37&38:- Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-Charge. Make: -B A Enterprises/Multiwyn/Doorwyn/ Modern fabricator/Madhu industries/Ajanta Ispat/Alusys/AVA steels or equivalent as approved by GE.

S & F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples or wooden beeds all as specified and directed.

S & F in repairs galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples or wooden beeds all as specified and directed. Make for Item No. 40&41: -Kamal/Shalimar or equivalent as approved by GE.

S&F Mild steel works as in grills, framed guard bars, and similar works conforming to Fe-290, Gde E-165 all as specified and directed.

S&F 100 mm size cold rolled mild steel medium weight butt hinges complete all as specified and directed.

S&F 100 mm size cold rolled mild steel medium weight butt hinges including taking down existing hinge complete all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised including taking down existing handle complete all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section including taking down existing tower bolt complete all as specified and directed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy including taking down existing sliding door bolt complete all as specified and directed. Make for Item No. 42 to 50: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE/ARGENT/Bharat/Alans/Hettich/Everlite or any ISI marked make as approved by GE.

S & F 3mm thick sheet glass ordinary quality fixed with oil putty and necessary clips/nut bolts or beads area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass and S & F 3mm thick sheet glass ordinary quality fixed with oil putty or beads and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

S & F 3mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts or beads area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass and S & F 3mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts or beads area exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge. Make for item Nos. 51 to 54:- TRIVENI/ SAINT GOBAIN/ MODIGUARD/ATUL/ HINDUSTAN or equivalent as approved by GE.

S&F in repairs harrison rails (curtain rods or drapery rods) aluminium powder coated 18-19mm dia with fixing brackets, stops, rollers etc., complete all as directed by Engineer-in-Charge.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparing new steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge. Make for Item No. 56&57: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/ NEROLAC

M&L for preparation of old plastered/unplasterd white washed surfaces of walls and applying one coat of white washing complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old plastered/unplasterd white washed surfaces of ceilings and applying one coat of white washing complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old plastered/unplasterd colour washed surfaces of walls and applying one coat of colour washing complete all as specified and as directed by Engineer-in-Charge. Make for item Nos. 58 to 60: LOVELYCEM/ SURYACEM/ JANATHACEM/ LUCKYCEM or equivalent make as approved by GE.

M&L preparing old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L preparing old painted steel and iron surfaces of any description over 10 cm width or girth (other than in roof) and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L preparing old painted steel and iron surfaces of any description over 10 cm width or girth of CGI sheet in roof etc., and applying one coat of synthetic enamel paint (Corrugal) complete all as specified and directed by Engineer-in-Charge. Make for item No. 61 to 63: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON/IEL

M&L for preparation of old distempered surfaces of walls by washing, rubbing down and stopping and applying one coat of distemper oil emulsion complete all as specified and as directed by Engineer-in-Charge. Make: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying one coat of creosote oil complete all as specified and directed by Engineer-in-Charge.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying one coat of varnish complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of the existing treatment on walls by scraping and washing down with water including making good the surfaces, from surfaces of walls and applying two coats of cement base paint over one coat of primer complete all as specified and as directed by Engineer-in-Charge. Make: INDOCEM/ SUPERSNOWCEM/ AQUACEM/ DURACEM

M&L for preparation of walls and applying one coat of cement base paint complete all as specified and as directed by Engineer-in-Charge. Make: INDOCEM/ SUPERSNOWCEM/ AQUACEM/ DURACEM

M&L for Complete removal of the existing treatment on walls by scraping and washing down with water including making good the surfaces, of walls and applying two coats of premium Exterior emulsion paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. Make: APPEX of ASIAN or equivalent in JENSON & NICHOLSON/ BERGER/ SHALIMAR

M&L for preparation of surfaces of walls and applying two coats of premium Exterior emulsion paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. Make: APPEX of ASIAN or equivalent in JENSON & NICHOLSON/ BERGER/ SHALIMAR

M& L for Obliterating old writing of any description not exceeding 0.10 sqm with thick paint to match existing work complete all as specified and directed by Engineer-in-Charge.

M& L for Obliterating old writing of any description exceeding 0.10 sqm and not exceeding 0.50 Sqm with thick paint to match existing work complete all as specified and directed by Engineer-in-Charge.

S&F solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixed on existing PVC frame including dismantling of existing lining complete all as specified and directed by Engr-in-Charge. Make: SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

Sub Total of Schedule 'A'

Schedule of Credit (Minus) Rs. 13,520.00 B/F from Ser page No. 28 NOTE: Bidder shall insert credit amount as rate Rs. 13,520.00 in Green field under Col-M. If bidder does not insert the amount the same will be deducted from total amount of Schedule 'A' and accordingly total amount of tender will be considered in deciding the lowest tender.

Sub Total of Schedule of Credit

SANJAY SAW MILL

G K SUTHAR

SUNIL PRADHAN

GARGO TRADERS

S K ENTERPRISES

JAYSHREE CONCERN