Vertical extension of OPD Building (3rd floor)

Amount

CIVIL WORKS

All works above plinth and upto floor V level

Concrete of M10 grade with minimum cement content of 220 kg /cum

REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc. and removal of form for

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.

200 mm wide.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063).

Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Wall Joint of 100 mm gap

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions / cup boards self's by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

White Agaria Marble Stone

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 65 x 150 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Rectangular or square

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished seamless type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Extra for pre finished nosing to treads of steps of marble/granite stone.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Double charge vitrified tile polished finish of size

Size of Tile 600x600 mm

Providing and laying double charge vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks)

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:

8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

12 mm cement plaster of mix :

1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

10 m - 13 m height

13 m - 16 m height

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

White washing with lime to give an even shade :

New work (three or more coats)

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

French spirit polishing :

Two or more coats on new works including a coat of wood filler

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Double Leaf Emergency Escape Fire Doors

Providing and fixing of fire rated 5 Knuckle, 2 bearing butt hinges (size 4" x 3" x 3mm), with satin finish SS 304 grade stainless steel. As per EN 1935, CE Marked. Suitable for door weights upto 120kgs. all complete as per direction of engineer-in-charge. Approved Make: ormakaba/ Union(AssaAbloy)/ FSB /Union(AssaAbloy) /Geze

Providing and fixing of fire rated rack and pinion door closer (EN size 3-6), including standard arm and two independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed with slide plate. For Door width upto 1400mm Silver finish. As per EN 1154 and CE marked. all complete as per direction of engineer-in-charge Approved Make : dormakaba/ Union(AssaAbloy) /FSB /Union (AssaAbloy)

Providing and fixing of 1 & 2 Point Locking Panic Hardware for Double Leaf Rebated fire door consisting of 1 Point locking Panic Latch set for Active Leaf & 2 Point Locking Panic Bolt set on Inactive Leaf. Including External Trim Lever Type. Complete set including Spindle, screws , all fixing accessories and 5 pin Euro profile half cylinder with one side key operation standard length 42mm in satin nickel plated finish with 3 keys. all complete as per direction of engineer-in-charge Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of fire rated automatic door bottom RP8si seal from Raven, extruded silicon sealing component, spring loaded to lift clear of the floor. Concealed mounted in a 15mm x 34mm groove. Max gap 13mm. Finish: Anadoised satin clear. L=920mm as per direction of engineer-in-charge Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of Surface mounted door coordinator for double leaf fire rated doors SR 390, zinc plated, non-Handed as per EN 1158 and CE marked all complete as per direction of engineer-in-charge Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of self adhesive fire rated delta seal for acoustic, fire and smoke protection, of Finish = Black, Length = 1 x 2000mm, Height- 2 x 2750 mm as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Hardware For NON Fire Doors - Pull Handle

Providing and fixing of 5 Knuckle, 2 bearing butt hinges (size 4" x 3" x 3mm), with satin finish SS 304 grade stainless steel. As per EN 1935, CE Marked. Suitable for door weights upto 120kgs. With template drilled as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of rack and pinion door closer EN size 2/3/4, including std. arm and with two independent closing valves and latching speed adjustable by arm. Silver finish. As per EN 1154. as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of Antiviral / Antimicrobial coated H Shaped Pull Handle with clear & transparent coating with protection tested for antibacterial activity with up to 99.9% effectiveness* as per ISO 22196 and antiviral activity with 99.9% reduction as per ISO 21702. H shaped pull Handle with back to back with 350mm CTC, adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =450mm, 25mm dia, SS304. as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of Type 1 Dead Lock Package including 55mm backset, 20mm square forend prepared for euro profile cylinder including strike plate and EPC 60mm Length both side key operation & Escutcheons in SSS Finish. all complete as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of floor stop half dome with 45mm dia including necessary screws, in satin Chrome all complete as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing and fixing of wall mounted door stop dome with 60mm length including necessary screws all complete as per direction of engineer-in-charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing & Fixing of Sliding Door System for Timber Door weight upto 80kgs single door, 2 Metre Length complete including Accessories - 1 Set Track, 2 mts length - 1 No. Sliding system SLM 80 with clamps, 2 rollers, end stops and fixing accessories. Suitable for wood door weight upto 80kgs, single door. Finish - Anodised Finish as per direction of Engineer-in-Charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing & Fixing of Mortice sliding door 400 claw bolt with 55mm backset, 22mm sq forend including strike plate in satin stainless steel. EPC 60mm Length, 5 pin Euro profile knob cylinder including internal thumb turn and external key operation standard length 60mm in satin nickel plated finish with 3 keys as per direction of Engineer-in-Charge. Note: Optional master keying and grand master keying can be done on request. -NMK Approved Make : dormakaba /Union(AssaAbloy) /FSB

Providing & Fixing of flush pull for sliding door, rectangular. Finish - Satin stainless steel including necessary screws all complete as per direction of Engineer-in-Charge. Approved Make : dormakaba /Union(AssaAbloy) /FSB

Core cutting including filling of sealant in RCC work for all thickness as per direction of engineer-in-charge.up to 50 mm dia

Core cutting including filling of sealant in RCC work for all thickness as per direction of engineer-in-charge.up to 100 mm dia

Core cutting including filling of sealant in RCC work for all thickness as per direction of engineer-in-charge.up to 250 mm dia

Making grooves of 5mm wide, 3mm deep in 3 row on granite stone steps with all necessary tools and machinery complete as per the direction of engineer-in-charge.

PLUMBING WORKS INTERNAL & EXTERNAL

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing in position best indian Health Faucet with 8mm dai 1 meter long Flaxible Tube and wall bracket with N. R. V. (nonreturn wall).

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm C.P. brass single hole basin mixer.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

(a) 15 mm nominal dia

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face withconcealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing, jointing and fixing UPVC SOIL WASTE & Rain Water System. The work shall be done as per technical specifications and in general shall include: Material: UPVC pipes conforming to IS : 4985 and fittings (moulded conforming to IS: 7834 and fabricated conforming to IS: 10124) Fittings shall include all standard moulded as well as fabricated fittings like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, cowl, adaptors for connections to other materials, plugs, reducers, cowls, offsets and other specials Jointing:

40mm ( in. 6kg/cm2)

Providing and fixing 110 mm dia PVC floor trap moulded EXTENTION PIECE (Height Riser) having 3 nos. boss inlets suitable for 50 and 40 mm pipe connections, jointing and dripseal all complete as per standard detail.

Providing and fixing floor drain points formed out of UPVC 110 X 50 mm dia reducer with suitable extension piece including cost of cutting and making good the walls and floors wherever required.

Providing and fixing C.P JALI 125 mm X 125 mm square vertical grating fixed in wall / floor for tarrace rain water outlet, complete work.

Providing, jointing and fixing UPVC Soil, Waste and Vent pipes of approved make conforming to IS : 13592 Class B, 6 kg/cm2 pressure including fittings and specials, i.e. bends, tees, crosses, access pieces, adaptors for connections to other materials, plugs, reducers, cowls, offsets, etc.in pipe ducts , sunken floors, under slung from ceiling and jointing with epoxy based sealant-`Dripseal`, Pipes may be laid/ fixed in pipe ducts, sunken floors, under slung from ceiling. The pipes shall be laid to

63 mm dia

110 mm dia

Providing and fixing in position 110x63 mm dia uPVC reducing elbow including fix to floor with cement mortar.

Providing and fixing in position 125x125 mm stainless steel grating for floor trap/floor drain including fix to floor with cement mortar.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

Concealed work including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing ofjoints complete as per direction of Engineer in Charge

Internal work - Exposed on wall

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required

100 mm dia

Supply and installation of Crosslinked Closed cell Polyethylene FR XPE Thermal insulation on ducts havine density 0f 30± 3 Kg/ M³ ,having K value 0.034 W/m ° K at 23°C Deg temp and temp range of -40°C to +115°C and fire rating Class O as per BS 476 Part 6 from Exova Warringtonfire-UK and CBRI,Roorkee as per the approved specifications. Material shall be HCFC/CFC free as per US EPA 5021 A (2014 )

For 20 mm dia Pipe 6 mm thick (Concealed Pipes)

For 25 mm dia Pipe 6 mm thick (Concealed Pipes)

Supply and installation of Crosslinked Closed cell Polyethylene FR XPE Thermal insulation on ducts havine density 0f 30± 3 Kg/ M³ ,having K value 0.034 W/m ° K at 23°C Deg temp and temp range of -40°C to +115°C and fire rating Class O as per BS 476 Part 6 from Exova Warringtonfire-UK and CBRI,Roorkee as per the approved specifications. Material shall be HCFC/CFC free as per US EPA 5021 A (2014 )

13 mm thick (Exposed Pipes)

For 20 mm dia Pipe

For 25 mm dia Pipe

Providing and fixing forged brass single acting air release valve with screwed inlet 25 mm dia.

Providing and fixing of Single phase electrical actuator operated wafer type rubber lined butterfly valve with by pass arrangement as per drawing attached including level controller, 3 nos. normal butter fly valves,necessary control and Power cables (Maximum 10 M. Length of each type) and control panel installed on OH tank filling line near the tanks complete in all respects.

40 mm dia.

FIRE FIGHTING WORKS

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

150 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for nstantaneous connection to interconnect hose pipe coupling as required :

Stainless Steel (Grade 304)

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width x 50mm depth x 1.6 mm thickness.

Providing and fixing MS partly glazed single/double hung lockable shutter fabricated from MS section as required with 5 mm thick glass for fire station complete including stove enamelled painting of door and frame and words "Fire Hydrant" written on glass, suitable to accommodate 2 Hydrant landing valves, 1 fire hose reel, 2 nos.15m long 63 mm dia hose,1-branch pipe, 1no. fire man's axe, fire extiguishers 2 nos, including suitably mounted on a raised masonry platform as required. (Approx.size 0.90 m x 2.1m )

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Fire Extinguisher, ABC Type Capacity 6 kg, ISI Marked IS: 15683 (Stored Pressure)

Capacity 6.0 Kg.

Providing and fixing carbon-di-oxide fire extingushers trolley mounted with all accessories internal discharge tube,high pressure discharge hose,discharge nozzle, ISI marked as per IS:2878 finished externally with red enamel paint. (Halon Free Gas)

Fire Extinguisher, CO2 Type Capacity 4.5 kg, ISI Marked IS: 15683 (Make- Exflame)

Capacity 4.5 Kg.

INTERNAL & EXTERNAL ELECTRICAL WORKS

Point wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Group/Loop Control Point wiring in PVC conduit, with modular type switch :-

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :-

Wiring for light /power plug with 2 x 4 Sq.mm. FRLS PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no. 4 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub main wiring in PVC conduit :-

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated, copper conductor single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire

2 x 16 sq.mm. + 1 x 6 sq.mm. Earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 x 16 sq.mm. + 2 x 6 sq.mm. Earth wire

Supply and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. modular switch, connection etc. as required.

S/F power plug point modular type accessories :-

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps. modular switch, connection etc. as required.

S/F modular type electronic fan regulator :-

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F modular type blanking plate :-

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing 5 amps. to 32 amps. rating, 240/415 V, 10kA, "C" curve, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

4 way, Double door

6 way, Double door

8 way, Double door

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 2 nos 3 pin 5/6 amps modular socket outlet and 2 nos 5/6 amps. modular switch, connection etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

Supplying and fixing surface mounted 8-10W LED (600mm) Mirror light, Decorative Box type Pre wired fitting suitable for 8-10W LED tube, 100 Lm/W completer with connection testing, commission etc as required. (BAJAJ model No BCLSB 10 WH or equivalent in Wipro, Philips) (LM 79 & LM 80 reportfrom NABL Accredited lab.)

Supply Installation Testing and Commissioning of 1 x 18 to 22 watt 1200 mm LED fitting made out box type Channel made out of CRCA duly powder coated and suitable for 18watt LED Lamp .The LED lamps should have a system efficacy of 100lumens/watt having colour temperture of 6000 to 6500, 100Lm/W kelvin, CRI >75, and driver would have a power factor >0.9,THD <20% and efficiency > 85%. complete with all accessories and tube etc directly on ceiling /wall i/c connection. with 1.5 sq mm FRLS PVC insulated copper cond. single core cable and earthing etc. complete as required. (Bajaj model No BCLSB 18 NW or equivalent in Wipro, Philips) (LM 79 & LM 80 report from from NABL Accredited lab.)

Supplying, installation, testing & ommissioning of surface type 10W to 12W LED Round Downlight with pressure die-cast aluminium heat sink & glarefree opal Diffuser. Total system Lumen of 10W to 12W LED should be 1000 or above in Cool day Light(6000K to 6500K), Power factor>0.95, CRI>80, LED Make- Cree, Nichia,Philips Lumiled, Osram, LED Efficacy>100 Lm/W asper Bajaj Cat No BPSLR Surface 12W LED WH RD SD / Philips / Wipro. Complete with all accessories as required with connections.

Supplying, installation, testing & Commissioning of 10W to 12W LED Bulkhead fitting opal Diffuser, IP 65, Inbuilt surge Protection. Total system Lumen of minimum 1000 Lumen, Complete with all accessories as required with connections. (Bajaj Cat No BIBWP 10W LED or equivalent in Wipro /Philips) (LM 79 & LM 80 report from NABL Accredited lab.

Supplying, installation, testing & ommissioning of recessed type 15W to 18W LED Round Downlight with pressure die-cast aluminium heat sink & glarefree opal Diffuser. Total system Lumen of 15W to 18W LED should be Minimum 1000 or above in Cool day Light(6000K to 6500K), Power factor>0.95, CRI>80, LED Make- Cree, Nichia,Philips Lumiled, Edison, LED Efficacy>100 Lm/W. Complete with all accessories as required with connections. (Bajaj cat no. BGSLO Sleek Recess RD 15W WH LED, or equivalent in Wipro / Philips (LM 79 & LM 80 report from from NABL Accredited lab.)

Supplying, installation, testing & ommissioning of recessed type 30W to 36W Full window glarefree opal Diffuser LED Panel of size 595X595mm suitable for Armstrong/POP/GB ceiling with MS Powder coated White Housing. Total system Lumen of LED should be 3600 or above in Cool day Light(5700K to 6500K), Power factor>0.95, CRI (Ra) >80, LED Make- Cree, Nichia,Philips Lumiled, Osram, LED Lamp Efficacy>100 Lm/W. Complete with all accessories as required with connections. (Bajaj Cat No BZRSQL 36L LED GX PRO WH or equivalent in Wipro / Philips (LM 79 & LM 80 report from NABL Accredited lab.)

Supplying, Installation of heavy duty of 900 RPM. having double ball bearing motor with high air delivery Exhaust fan with louver and shutter of size 300mm sweep suitable for single phase AC supply in the existing opening including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as reqd.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, Installation, Testing & Commissioning of FLOOR PANEL, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor/Wall mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification.

Incomer

125A FP 35kA MCCB with thermal magnetic release with adjustable OL, SC and EF protection - 1 nos.

Busbar

1 Set of 200 A TPN busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing.

Instruments

2A, C curve SP MCB - 3 nos.

RYB indication lamp, LED type - 3 nos.

1 No 3 phase Digital Multi function meter to read V, A, F, kW, kWh, Acc class 1.

125/5A 5VA class 1 resin cast CT - 1 set

Outgoing.

63 A FP 10 kA MCB - 8 nos.

40 A DP 10 kA MCB - 2 nos.

Supply, Installation, Testing & Commissioning of UPS PANEL, cubicle type, made out of min 2mm thick CRCA sheet (load bearing), totally enclosed, IP42, free standing, floor/Wall mounting, dust and vermin proof, powder coated, indoor, compartmentalised, suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system, including internal wiring with suitable size wires, rotary handle, spreaders, 3mm thick gland plate, hinged type door with neoprene / PU gasket, IS 8623 etc. The panel shall include supply & installation of following switchgears, metering instruments and accessories as per specification.

Incomer

100A FP 35kA MCCB with thermal magnetic release with adjustable OL, SC and EF protection - 1 nos.

Busbar

1 Set of 200 A TPN busbars of high conductivity electrolytic quality Aluminium alloy and suitable size earthing conductor through out the panel for its earthing.

Instruments

2A, C curve SP MCB - 3 nos.

RYB indication lamp, LED type - 3 nos.

1 No 3 phase Digital Multi function meter to read V, A, F, kW, kWh, Acc class 1.

100/5A 5VA class 1 resin cast CT - 1 set

Outgoing.

63 A FP 10 kA MCB - 8 nos.

40 A DP 10 kA MCB - 2 nos.

Supply, Laying, Fixing, Testing and Commissioning of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor cable of 1.1 KV grade on surface/ in open masonary duct/cable tray/ ground for connection as reqd

50 sqmm 3 1/2 core

70 sqmm 3 1/2 core

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5 x 50 Sq mm (35 mm)

3.5 x 70 Sq mm (38 mm)

Supply and installing following size of perforated hot dipped GI cable trays(galvanisation thickness not less than 50 microns) with perforations not more that 17.5% in convenient sections, jointed with connectors, suspended from the ceiling with GI suspenders / fixed to walls with suitable GI clamps, including bolts and nuts, bends, reducers, Tees, cross members etc as required.

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supply, installation, testing and commissioning and testing of 30KVA, 415V, 3ph input & 3 ph output ON-LINE UPS system back up protection for 30 minutes and along with all company's standard accessories as required.

Details of UPS :-

(IGBT based rectifier & inverter) True Online UPS Systems having 15 Minutes battery Backup with each UPS System with MS Rack, Interlink Cables and DC cables with all accessories. UPS shall be provided with SNMP protocol for BMS interface.

Details of SMF Batteries:-

Sealed Maintenance free (SMF) Batteries for 30 Mins. backup with open type MS Rack for installation of batteries and their respective battery leads copper cables / Interlink between batteries, copper cables between UPS & batteries, DC Isolator, with suitable size of Rack for batteries (as per battery manufacturer's standard) and etc. as required. Make :- Exide / Quanta/ Amaron.

Isolation ;- Inbuilt at the input side of UPS System.

Back-up time :- 15 min. with SMF Batteries upto 0.99 Load Power Factor

VAH required :- Suitable size VAH for 30 KVA

Display :- Should have LCD Display

Upgradeability :- Should be upgradable to work as parrallel redundent UPS in load sharing mode.

15 Minutes on Full Load. ( calculation need to be provided ) as per OEM ( Battery Configuration has to be mentioned ) with racks

Display : Should have LCD display with event logging facility.

Flexi DC Bus of 30 to 44 Nos of 12 V SMF batteries to be available.

Should be Parallable in the Eco Mode configuration

The Energy Efficenecy requirment of UPS system at 100 Load shall be vary from 91.9% to 93.8% or more.

Input Frequecy Range: 40-70 Hz

Including 5 (3P+2N+2E) runs of suitable size copper cable from the circuit breaker in UPS room to the UPS and from UPS to the UPS panel.

Total cost of 30 KVA UPS with batteries and other acessories

Supply and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing of 32mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of GI box of following size modules, alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

Supply and drawing of UTP 4 pair Cat 6 LAN cable in the existing surface/recessed PVC conduit as required.

one run

two run

three run

Supply,installation,testring and commisioning of following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

RJ 45 socket

Supply,installation,testing and commisioning of 12 port unmanaged ethernet switch with 2 nos fiber ports

Supply,installation,testing and commisioning of 24 port unmanaged ethernet switch with 2 nos fiber ports

Supply,installation,testing and commisioning of Cat-6 shuttered 12 port fully loaded patch panel with 2 nos fiber ports

Supply,installation,testing and commisioning of 24 port Patch panel fully loaded, Cat-6 UTP Keystone Type.

Supply,installation,testing and commisioning of Cat-6 UTP 24AWG patch cord, 1 meter, Plug 30U, snaglless etc as required.

Supply,installation,testing and commisioning of Cat-6 UTP 24AWG patch cord, 2 meter, Plug 30U, snaglless etc as required.

Supply,installation,testring and commisioning of 24 port L2 managed core switch with 2 nos fiber ports

Supply,installation,testring and commisioning of 9U rack with Front glass door, Rear Perforated door with handle Lock & key. Front/Rear 19" mounting angles, top, bottom open, RAL 9005 with all other accessories

Supply,installation,testring and commisioning of 15U rack with Front glass door, Rear Perforated door with handle Lock & key. Front/Rear 19" mounting angles, top, bottom open, RAL 9005 with all other accessories

Supplying and drawing 2 pair, 0.5 sq mm FR PVC insulated copper conductor, un armoured telephone cable in the existing surface/recessed steel/ PVC conduit.

Supply and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing of 32mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

Telephone socket

Supplying and fixing of GI box of following size modules, alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 module( 75 mmx75 mm)

Supply,laying and termination of 50 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray

Supply,laying and termination of 50 pair telephone terminal block housed in engineering plastic box with transparent hinged door

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required

Supply and fixing of 25mm medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

TV antenna socket outlet

Supplying and fixing following size/ modules,GI box along with modular base, cover plate for modular switches in recess etc as required.

1 or 2 module( 75 mmx75 mm)

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as required.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable strobe complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and fixing of following sizes of 32mm steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size includingconnections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing of following sizes of 25mm steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supply, installation, testing & commissioning of lift of following capacities and type suitable for operation on 415 V, 3 phase, 50 Hz AC supply, having AC variable voltage and variable frequency typel, with machine room, speed of 1.00 Mtr/sec, electromagnetic brake system, simple operations, operating control panel with luminous buttons, overload warning indicator, battery operated alarm bell, LED type emergency light, intercom suitable for hook up to EPABX, infrared ray sensing door protection for full height, reverse phase relay on controller, fireman’s switch at ground floor, ARD system etc complete as required.

Digital car positions indicator in car and at all positions indicator in car and at all floors with Up/DOWN direction, all signal fixtures in stainless stell faceplates, light fixtures, ventilation fan, etc complete with all accessories including automatic rescue device in the event of power failure etc., Complete with necessary scaffolding, electrical panel, logic control panel and shaft lighting etc required for the erection of the elevators as required.

Machine Room (MR) Type with the traction motor placed in Lift top (suitable for lift) complete as per cpwd specification, simplex full collective operation with/without attendant. Car/Hoistway Entrance, protected by stainless steel hairline doors and clear center /side opening min as per site. 13 to 20 passanger Lift (as per site), suitable car size Inside dimensions and entrance at front side on all the serving floors, provided with matt finish stainless steel panel on all four side and ceiling, stretcher protection on three sides complete as per requirment.

Extension of lift 1 stops & 1 openings ,Total travel height is approximately 3--5M, Speed 1.50MPS

M/S nabajit traders & Engineers