NIT-08 of 19-20 SPECIAL REPAIR TO BLDG NO T-88 AND T-31 AT 261 TRANSIT CAMP UNDER GE (I) 873 EWS

Amount

B/R Portion

Demolition of brick work masonry built in cement mortar including all quoins, pillars etc. but excluding ashlars facing, dressed stone work and precast concrete articles complete all as specified and as directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in in CM 1:6, complete all as specified and directed.

Brick work with sub class ‘B’ bricks (old size), straight or curved on plan to any radius, in half brick thick wall built in cement mortar 1:4, complete all as specified & directed.

Demolition of cement concrete (reinforced) of any description and in any position, complete all as specified and as directed.

Precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slab for manholes set in cement mortar 1:4 complete all a specified and as directed.

TMT bars 6 to 8mm dia and over, cut to length bent to shape including binding with MS annealed wire of dia not less than 0.90 mm, complete, all as specified and as directed.

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in two layers, 5mm thick using WPC @ 3% by weight of cement over 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement, complete all as specified. Note :- WPC shall be measured and paid separately.

Rendering 15mm thick in cement mortar 1: 6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement, complete all as specified.

Rendering 10mm thick in cement mortar 1:4 on brick work or concrete surfaces as on ceiling, finished even and smooth with out using extra cement, complete all as specified and directed.

Supply only integral water proofing compound all as specified and as directed.

Demolition of cement concrete in ground floors and paving (un-reinforced) not exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

75 mm thick Cement concrete type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) in sub base, complete all as specified and directed.

75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggregate) in sub base of flooring, complete all as specified and directed.

50mm thick PCC 1:2:4, type B-2 (using 40mm graded crushed stone aggregate) as in sub-base of flooring, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar including removal of debries outside cantt area, complete all as specified and as directed.

25mm thick PCC 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate) as in floor, finished even and fair to receive floor finishes, complete all as specified & directed.

Non-skid coloured glazed ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Glazed ceramic coloured wall tiles in any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) in vertical surfaces of size 300mm x 200mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

16mm to 18mm thick of size not less than 53 x 53cm, machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing, over and including 15mm thick screed bed or bedding layer of cement mortar 1:4 all as specified and as directed.

16mm to 18mm thick, machine cut Kota stone as in riser or steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and rounding off edges complete with mirror finish polishing, over and including 15mm thick backing coat of cement mortar 1:3 all as specified and as directed.

Makrana white marble tiles 30cm x 20cm x 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types over and including 15mm thick screed bed in cement mortar 1:3, complete all as specified and directed.

20mm thick Granite stone (table rubbed and polished) in steps, risers, jambs, pillars, window cills, cooking platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in cement mortar 1:4 finished fair to received the granite including rounding the exposed edges, complete all as specified and directed.

Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floors including over 15mm screed bed in CM 1:3, complete all as specified & directed.

Taking down chowkhats with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

2nd hard wood as in plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and directed.

Mild steel works as in clamps, hold fasts and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified & directed.

PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in bed block for hold fast and similar works etc. complete all as specified and directed.

35mm thick 2nd class Hard wood factory made rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

35mm thick, 2nd Class hard wood, factory made, glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

Steel windows with side hung shutter including projecting type hinges, steel handle 02 Nos., steel tower bolts 100mm long and steel peg stays lugs including hold fast complete with glazing bars dovetailed or welded including locking arrangement, complete all as specified and as directed.

Steel windows with side hung shutter including projecting type hinges, steel handle 02 Nos., steel tower bolts 100mm long and steel peg stays lugs including hold fast complete without glazing bars dovetailed or welded including locking arrangement, complete all as specified and as directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and directed.

Mild steel framed works such as grills, framed guard bars, etc. and similar work conforming to Fe-410-O or Fe-310-O grade, including bending, cutting and welding as required, complete all as specified and as directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified & directed.

Factory made solid panel PVC door / cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification in SSR Part-I.

Butt hinges, medium weight, cold rolled mild steel, 100mm size, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300mm, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of Size 150mm long complete all as specified and directed.

Aluminium handle cast type anodized of size 150mm complete all as specified and directed.

Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete, complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone, concrete or brick surrounds glazed with putty or fixed with beads.

4mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 Sqm each complete all as specified and directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and aperture 1.40mm and fixed with tinned tacks or galvanized wire staple all as specified and directed at site

Preparation of roof surfcaes by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and roughening old concrete roof surfaces and applying cement slurry with 3.0 Kg of cement per Sqm and applying the following Roof Treatment complete all as directed :- (a) Applying 1st course of 10mm thick screed bed with cement mortar 1:3 over concrete surface. (b) Applying 2nd course of bituminous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

(d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric membrane 3mm thick weight not less than 3.6 Kilogram/Square Metre with 160 Grams/Square Metre non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (f) Applying two coats of aluminium paint over APP membrane complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Mild steel rolled work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, square / rectangle sections, channel or flat section) including distance pieces, cleats etc. confirming to grade FE 410-0 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering, fixed with self taping screws, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / cladding to wall, fixed with self taping screws, complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, PVC, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and as directed.

6mm thick non asbestos fibre cement building boards laid / inserted to GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and hangers 6mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40mm x 30mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long and scrwed at 450mm centre to centre / intermediate channel 0.9mm thick having two equal

flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleats and steel expansion fasteners with and including ceiling section (not exceeding 1.20 metre length) of 0.55 mm thickness having kurled web of 50mm and flanged of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457 mm centre to centre, size of grid 605mm x 605mm complete all as specified and directed.

Mild steel framed works such as grills, framed guard bars, framework of water tanks and similar work conforming to Fe- 410- O or Fe- 310-O grade, including bending, cutting and welding as required, complete all as specified and as directed.

Dismantling PVC water tanks exceeding 1000 ltr capacity but not exceeding 2000ltrs, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position, including over flow and drain out pipe complete of 2000 litre capacity complete all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed to 20mm bore dia of pipe (Minimum weight 210gms), complete all as specified and directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 15mm dia bore iron pipe complete all as specified and as directed.

Gun metal globe or gate valve with iron wheel heads, screwed both ends for 20mm dia bore iron pipe complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 15mm dia complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 20 mm dia complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 25mm, complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from taking down here-in-before and fixed (walls, ceiling, floors, etc.) of 25 mm dia complete all as specified and as directed.

Bib tap with wall flange cast copper alloy CP, fancy type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed.

Stop cock / Angle valve with adjustable wall flange CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed.

Stop cock / Angle valve CP cast copper alloy, fancy type, concealed type, with long shank and cup, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed.

Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, fixed in repairs, complete all as specified and as directed.

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

Vitreous china wash hand basin, counter type size 470mm, coloured, oval shape, flat back including 32mm bore brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm and adequate length, 15mm bore PVC connection pipe 450mm long with brass nuts on both side and fitting in granite slab with proper moulding etc., complete all as specified and as directed. Note : The granite stone slab shall be mesaured and paid seperately.

PVC connection 45cm long fitted with PTMT nut and washer on both ends, fixed to 15mm bore iron pipes, complete all as specified and directed.

PVC flexible waste pipe of bore 32mm suitable for fixing to Wash Hand Basin / Kitchen Sink complete all as specified and directed.

Tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges, including pair of brackets, fixed in repair, complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes of 100 mm bore, jointed in cement mortar and taking out of trenches, if required, complete all as specified & directed.

Dismantling of cast iron or reinforced concrete drain pipes of 75 mm bore, jointed in cement mortar and taking out of trenches, if required, complete all as specified & directed.

Cast (sand) iron soil, waste and vent pipes, 110mm bore, in any length with or without ears, with cement joints fixed to wall, complete all as specified & directed.

Cast (sand) iron soil, waste and vent pipes, 75mm bore, in any length with or without ears, with cement joints fixed to wall, complete all as specified & directed.

Cast iron bends, 100mm bore, complete all as specified & directed.

Cast iron bends, 75mm bore, complete all as specified & directed.

Cast iron vent cowl, 100mm bore, complete all as specified & directed.

Cast iron vent cowl, 75mm bore, complete all as specified & directed.

PVC (SWR) Floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified & directed.

PVC (SWR) Gully trap 125/110mm setting and jointing with solvent cement with grating including jointing complete all as specified and directed.

Grating square 150 mm size of PTMT (Minimum weight 100gms), complete all as specified & directed.

PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds mitred/stopped ends etc. complete all as specified and directed.

Demolition and breaking up 150mm bore drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, complete all as specified & directed.

Salt glazed stone ware (SGSW) drain pipes of grade 'A' 150mm bore laid in trenches and jointed on concrete bed complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe plain cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregates) complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4, type B-1 smooth finished and reforming benching as required for 150mm bore pipe, complete all as specified and directed.

Preparation new plastered or previously untreated surfaces of ceiling and applying three coats of white wash , complete all as specified and directed.

Preparation old plastered or previously untreated surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

Preparation new plastered surfaces of walls and applying two coats of cement base paint including one coat of cement primer complete all as specified and directed.

Preparation old plastered / unplastered surfaces of walls and applying one coat of cement base paint, complete all as specified and directed.

Preparation new / old plastered surfaces of wall and applying two coats of oil emulsion distemper roller finish over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

E/M Portion

Taking out carefully copper/aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including PVC conduit and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sheet or cast iron boxes including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 108 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 108 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 108 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqmm conduit all as specified and directed.

Modular switch 1 way 6A, 1 module, complete all as specified and as directed.

Modular switch 1 way 16A, 1 module, complete all as specified and as directed.

Modular Socket, 6A, 2/3 pin combined 2 module, complete all as specified and as directed.

Modular Socket 6A/16A, 2/3 pin combined 2 module, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Modular Fan step regulator, 120W - 2 module including taking out the unserviceable, complete all as specified and as directed.

Modular white cover plate with frame, 1 module, complete all as specified and as directed.

Modular white cover plate with frame, 3 module, complete all as specified and as directed.

Modular white cover plate with frame, 6 module, complete all as specified and as directed.

Modular Metal flush box 1/2 module, complete all as specified and as directed.

Modular Metal flush box 3 module, complete all as specified and as directed.

Modular Metal flush box 6 module, complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

LED Lamp 230 volt 10 watts complete all as specified and as directed. Make : Havells / Crompton Greaves / Philips / Wipro

Tube light fitting box type suitable for and including LED 20 tube Rod 4' long with decorative colour in polycarbonate housing and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed. Make : Havells 'E-Lite LED Curve' Cat Part No LHEXBXPNIN1W020 or equivalent in Philips / Wipro / Crompton / Syska

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 4 Way, complete all as specified and as directed.

MCB SP 6 to 32 Amp 10 KA, complete all as specified and as directed.

RCBOs DP, 30mA for earth leakage, over load and short circuit protection, 32 Amps, complete all as specified and as directed.

Single pole enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, complete all as specified and as directed.

Storage water heater (Geyser), vertical type, of 25 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of nuts and bolts and necessary PCC work as specified and directed by Engineer-in-Charge. Make : VENUS 'SPLASH 02 GL' / RACOLD 'ETERNO 2 25 V' / BAJAJ 'MAJESTY 25L GMU' / HAVELLS 'PURO PLUS 25L'

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for laying cable / pipe or foundation of pole etc., and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Removing excavated soils to a distance exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 2 core including taking down/up unserviceable cable and making good disturbed surfaces, complete all as specified and directed.

Sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed Note : Punned thickness of 18cms shall be measured for payment.

Supply and laying brick covering with width equal to length of bricks as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with width of brick perpendicular to length of cable, all as specified and as directed.

Steel pipe galvanised light grade, 40 mm bore laid in trenches or under ground/floor or road of fixed with pole for protection of cable including GI clamps with bolts nuts and washers complete all as specified and directed.

Sub main wiring with two single core PVC insulated multistranded un-sheathed FRLS cable of size 4.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistranded unsheathed FRLS cable earth wire of 2.5 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Two run of 4.0 Sqmm wire, one run of 2.5 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Cutting the existing distribution mains and connecting to 15/20/25mm GI pipe in position after cutting of existing pipe line and dismantling the existing gate valve and fixing of GI Tee of suitable size including threading 15/20mm existing GI pipe fixing of GI union 15/20mm re-fixing the existing GI pipe without disturbing existing line including necessary earth work complete all as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

M S BANSI LAL CONSTRUCTION CO

pargal builders

M/S A TO Z ENGINEERS

Bidder Name

pargal builders

VARDHMAN INTERNATIONAL

M S BANSI LAL CONSTRUCTION CO

M/S A TO Z ENGINEERS