WBPWD/EEBED/NIQ-19/2020-21

Amount

Supply & delivery of outdoor type M.S. Pillar Box complete with car venture type base pedestal for holding the upper compartment of the Pillar Box. The overall dimension of the above Pillar Box (1200 x 900 x 700)mm. made from 3 mm. thick MS sheet with double door for free opening including both side (front and back side). The above door fitted with side of the Pillar Box by two sets hinge system arrangement with providing capsule hinge welded with the Pillar Box rigidly incl. providing door handle and providing vent at the top side of the Pillar Box incl. padlock system on the above Pillar Box for extra protection incl. S & F 2nos. 7 (seven) lever (Godrej) padlock with duplicate key in front and back side. There should be provision inside the Pillar Box of 1 No. suitable size of Hylamp sheet holding the electrical accessories with suitable size of angle iron frame fitted inside the middle portion of the Pillar Box and S & F of following accessories including necessary paintings as per direction of EIC.

Incoming a) S/F of 415 Volts 250Amp TPN SFU with HRC fuses on L.S & N.L (Make- L&T,cat no.-SK95514, type FN 250 TPN/ABB /Siemens) 1nos. 3 Bus bar chamber b) do-do 400 Amp capacity 99.9% - 99.5% electrolytic tinned copper 4 bar bus bar of required dimensions (same size) mounted on non-hygroscopic porcelain insulator / hylam sheet having sufficient di-electric strength duly wrapped with colour PVC tapes (Red, yellow, blue & black) for phases & neutral identification and keeping space --- 1 set.

Outgoing a) S/F of 415 Volts 125 Amp TPN SFU with 125A DIN type HRC fuses on L.S & N.L. (Make – L & T, cat no.- SK95511, type FN 125 TPN/ABB/Siemens) . ----3nos. b) S/F of 415 Volts 100 Amp TPN SFU with 100A DIN type HRC fuses on L.S & N.L. --(Make – L & T, cat no.- SK95005, type FN 100/ABB/ Siemens ) ---2nos. c) S/F of 415V, 63A DIN type SFU as distributer.----- (make:-L&T cat no. SK95569/ABB/Siemens)------1no

S&Laying of two cables ( Make : Polycab/ Havells/ Glostar/ Crystal/ Currency ) of following sqmm in an underground trench in single tier formation (horizontal), the trench size : 680 mm x 760 mm average depth, with brick protection on the top of each cable 8 (eight) Nos. bricks per Mtr. and 4 (four) Nos. bricks per Mtr. as separator between the bricks and cables and also trench to be filled up with shifted soil, levelling up and restoring surface duly rammed i) 4 core 95 sq.mm.

ii) 4 core 70 sq.mm.

iii) 2 core 10 sq.mm.

S & F compression type gland complete with brass gland, rubber ring for dust & moisture proof entry of following. PVC/A Al. cable incl. finishing the ends by crimping method as per G.S. i) 4 core 95 sq.mm.

ii) 4 core 70 sq.mm.

iii) 2 core 10 sq.mm.

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (ANCHOR) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3 mm thick and incl. 175x100x65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish [only PVC Rigid Conduit on ceiling and remaining portion concealed] Avg. Run 8 mtr

Do do to 250V 5A 3pin plug point incl. S&F 250V 3 pin flush type plug socket & on existing switch board (Anchor Make)

S/F of single/twin 20/18 watt LED 4ft fluo. fittings suspended 25cm below the ceiling with 2nos 20mm dia EI conduit supports fixed with “L” type MS clamp with the suitable size of fastner & nuts & bolt as per GS,with S/F suitable length of 3x1.5.sq.mm. copper wire,with painting :– a) Single fittings with 1no LED fluo. Lamp (Philips,Cat no-TMC 501 1xLED 18/20W EBE)

Distribution wiring in 3 X 1.5sqmm single core stranded FR PVC insulated & unsheathed copper wire (app. Make) in 20mm bore ,3mm thick mainly Rigid Conduit pipe on wall,to 2x5A 5pin flush type plug socket & piano key type switch fixed on MS CRC sheet metal swith board cum JB on wall inclbakelite top cover, Average run 6 mtr. (separate plug point)

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm diax 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level - By TATA-Medium GI pipe (Equpment Earthing)

Supply and installation of 440 volt, 200A, 4 way copper busbar chamber with sheet metal enclouser flushed on wall and mending good the damages. (Make - Bentec/Havells)

S&F of 415V 125A TPN SDFU on S.S. body 3nos 125A HRC fuses with 2 nos Cable end box on angle iron frame on wall with necessary inter connection (For each hostel) (Make L&T).

S&F of 415V 63A TPN SDFU on S.S. body 3nos 63A HRC fuses with 2 nos Cable end box on angle iron frame on wall with necessary inter connection (For ump room) (Make L&T).

Supply & fixing of 230V 70W LED outdoor / street light fitting complete with all accessories to be fixed /projected from the wall/pole of the building incl. making holes/ providing clamping arrangement & necessary GI reducer as required. S&F 32 mm GI Arm bracket pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. (Make Philips, BRP408 LED CW 240V PSU GR 70W/ similar to crompton)

S/F of 230V,150W LED flood light fittings including driver on ceiling with existing circular Head frame 600 mm dia G.I pole top arm bracket angle on 9 mtr pole including necessary inter connection & earthing attachment (Make Crompton cat - LFLN-150-CDL/60)

Supplying and Fixing CI water proof looping cable box hinge type having hinged CI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting. a)250x150x100mm

S/F of 230V 415V 3-phase 9A-15A MF-I starter on wall with Angle iron frame for compound light & necy. Inter connection. (L&T)

S/F 25mm x 6mm G.I. earth bus ber as per G.S.

Rates to be quoted will be inclusive of all the taxes incl. GST. No other additional charges will be applicable in addition to the quoted rates.

DELTA BROTHERS

M/S GRACIOUS ENGINEERING PROJECT

DIP ELECTRICALS