WELCOME MAINT SERVICES IN OFFRS MD ACCN AND REPAIR TO INTERNAL WATER SUPPLY, CHAJJA AND OTHER MISC WORKS FOR MD ACCN UNDER AGE B/R-II AT ITARANA, ALWAR

Amount

Taking down cement plaster of any description on walls, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified & directed.

M&L for demolition of concrete (unrreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to location outside defence land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L 100mm thick Cement concrete 1:2:4 type B-2, (40mm graded aggregate) as in flooring Finishing cement concrete surface even and smooth without using extra cement complete all as specified & directed.

M&L 75 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection including forming groove 10mm wide & 30mm deep & filled with bitumenious filler at intermediate span n.exc 5m without using extra cement complete all as specified& directed.

M&L fly ash brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick built in cement mortar 1:4.

M&L rendering 15mm thick,plaster on fair faces of brick work or stone masonry or concrete surfaces in CM 1:4 including finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick,plaster on fair faces of brick work or stone masonry or concrete surfaces in CM 1:6 including finished surfaces fair and even complete all as specifed and directed.

M & L 5mm thick rendering in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as in bedding layer of floor finished the surface even and rough complete all as specified and directed.

M&L for coloured Non skid ceramic tiles(Ist quality) 7 to 8mm thick area of each tile exc 0.11Sqm but not exc. 0.18 Sqm, as in floors etc., laid over and including 15 mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 13.00 above but in skirting over and including 10 mm thick plaster in cement mortar 1:6 including necessary cutting of tiles as required size all as specified and as directed.

M&L for coloured Non skid ceramic tiles(Ist quality) 7 to 8mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floors etc, laid over and including 15 mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic tiles (Ist quality) (coloured) 300mm x 200mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L glazed ceramic coloured tiles (Ist quality) in vertical surface 450mm x 300mm x 7-8 mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in Cement& Sand Mortar 1:4 complete all as specified and directed.

M&L for coloured Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade area of each tiles not exceeding 0.36 sqm, in floors etc including 15 mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 18.00 above but in skirting over and including 10 mm thick plaster in cement mortar 1:6 including necessary cutting of tiles as required size all as specified and as directed.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

M&L for 18-20mm thick Granite black colour (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platform, staircase treads and like jointed over and including 15mm thick screed in cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, compltee all as specified.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4..00 Sqm each.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) not exc 2.0 Sqm each.

S&F solid PVC door frame of size 50mmx47mm made out of 10mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast complete all as specified and directed. (SS Butt Hings shall be paid seperately supply only)

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

S&F mild steel framed work using angle Iron ,flat Iron ,round bars as in security doos/gates with end of bars shouldered and or rivetted or forged into spikes ,framed guard bars barred into iron doors, walkways railing framework amd similler work confiming to Fe 290, GDE E-165 all as specified and directed.

S&F 35mm thick, factory made panelled door shutter (two panel), plain, framed with 2nd class hard wood lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS-1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S&F 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F stainless steel butt hinges, 100mm medium weight and fixed all as directed.

S&F 150 mm aluminium anodised barrel tower bolts of extruded section.

S&F 150 mm extruded aluminium alloy handles , fabricated type, anodised.

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

S&F for powder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified& directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 3 mm thick wall care putty of approved tint complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of white wash complete all as specified.

M&L preparing new surfaces plastered or unplastered on walls etc & applying two coats of distemper oil emulsion over a layer of chalk whiting preparatory to distempering complete all as specified & directed.

M&L preparing new surfaces plastered or unplastered on walls etc & applying two coats of cement base paint over primer with alkali- resistant primering paint complete all as specified & directed.

M&L for preparing plastered or unplastered new surfaces of ceiling & applying three coats white wash complete all as specified & directed.

M&L for complete removal of existing treatment on walls and preparation of surfaces of walls and applying two coats of cement base paint of approved shade/tint on walls all as specified and directed.

M&L for brooming down old decorated surfaces of wall, plastered or unplastered including cornices, pilasters etc and applying two coats of white wash, complete, all as specified and directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

M&L preparation of old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coats of white wash complete all as specified.

Complete removal of existing treatment & preparation of old surfaces by washing rubbing down and stopping of plastered surfaces and applying two coats of Cement based paint white or tined on walls including over a one coat of alkali-resistant priming paint complete all as specified and directed.

M&L preparation of old decorated plastered/unplastered surfaces of ceilings & applying one coats of oil bound distemper (OBD) complete all as specified..

M&L for complete removal of existing treatment on walls and preparation of surfaces of walls and applying two coats of acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over & including white wall care putty 1mm thick all as specified & directed

M&L for prepararing surfaces plastered or unplastered old surfaces of ceilings and applying one coat of white wash complete all as specified & directed.

M&L for complete removal of existing treatment on walls and preparation of surfaces of walls and applying two coats of oil bound distemper (OBD) incl one coat of birla white wall care putty complete all as directed.

M&L for brooming down old decorated surfaces of wall, plastered or unplastered including cornices, pilasters etc and applying two coats of colour wash, complete, all as specified and directed.

M&L for brooming down old decorated surfaces of wall, plastered or unplastered including cornices, pilasters etc and applying one coat of colour wash, complete, all as specified and directed.

M&L for preparation of old wall surfaces by washing rubbing down and stopping of distempered surfaces and applying one coat of distemper oil emulsion white or tined on walls including cornices etc complete all as specified and directed.

M&L preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth with zinc chrome primer and applying one coat of synthetic enamel paint all as specified.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth with red oxide zinc chrome primer and applying one coat of synthetic enamel paint all as specified.

M&L for prepration of old surfaces of wall and applying one coat of appex paint all as specified & as directed.

Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 3.50mm thick ordinary sheet glass fixed with clips and oil putty/wooden beading completed in squares not exc 0.50 Sqm each pane all as specified and as directed.

All as per item No 57.00 above but 3.50mm thick figured glass, pin head type.

Supply only sheet glass ordinary quality,in squares n. exc. 0.5 SQM each 4.80 mm thick complete as directed.

Hacking out old broken glass from metal/aluminium frame incl punching or drilling out old glazing pins/springs/clips/ beading and providing & fixing new of any thickness/size of any description and S&F for 5.5 mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sq. m in each pane complete all as specified.

Hacking out old broken glass from metal/aluminium frame incl punching or drilling out old glazing pins/springs/clips/ beading and providing & fixing new of any thickness/size of any description from aluminium / steel frame and M&L 5.5 mm thick Sheet glass, frosted, on one side in square in each pane complete all as specified.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S&F 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work etc. including taking down existing frame work complete all as specified & directed.

S&F in repairs particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified & directed.

S&F in repairs powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative bowel at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

S&F in repairs MS drapery rod 19/20 mm dia fancy type with PVC coloured sleeves fixed with suitable brackets two Nos & PVC colour bowl two Nos at end for door/window complete all as directed.

S&F in repairs CP mild steel conduit pipe 19/20mm dia as in curtain rod including suitable brackets complete all as specified.

S&F in repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), complete all as specified & as directed.

S&F in repairs brass mortice lock, vertical type, size 65mm, 2 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified.

S&F in repairs MS helical door spring 300 mm size with roller & roller plate fixed to wooden or steel frames with screws /welding as required at site complete all as specified.

S&F in repairs 300 mm long aluminium alloy anodised sliding door bolt with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium and fixed all as specified.

S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & directed.

S&F 75mm extruded brass handles, fabricated type polished complete all as specified & directed.

S&F in repairs extruded aluminium alloy handle, fabricated type, anodised, 125mm size, (ISI marked) complete all as specified.

S&F as in repairs 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S&F in repairs butt hinges 100 mm long medium weight cold rolled MS fixed in repairs to wooden or pressed steel/angle iron frames by welding all as specified.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed overall length 140 mm complete all as specified & directed.

S&F in repairs MS steel window stay 300 mm long for steel windows all as specified and directed by Engineer-in-Charge.

S&F in repairs handles left & right for steel windows all as specified and directed by Engineer-in-Charge.

Running welding in repairs not exceeding 6mm thick all as specified and directed by Engineer-in-Charge.

Welding in repairs not exceeding 6mm thick and not exceeding 2.5 cm in length all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description not exc 1 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

M&L for Cutting holes into or through but in stone walls built in cement mortar or cement lime mortar and walls of cement concrete. and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required superficial area N exc 150 sqm cm for purlin, rafter complete all as directed by Engr-in-charge.

S&F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame n. exc 1.5 sq. m each & removing to store.

Checking and attending to Plumber complaints like water leakage from taps, flushing cisterns, wash hand basins & other water supply fittings/fixtures and any obstruction to water supply in rooms, requiring plumber work and carryout minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern etc including petty materials like washers of all sizes, thread(soot), M-Seal, screws, nails, white cement to make water supply/plumbing lines functional and leak proof. Note: (i) Contractor or his authorised representative collect such type of complaints from B/R-II complaint cell at 8.30 AM on daily except Sunday & Holiday. No extra payment shall be made on account of collection of complaint. (ii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor.

Checking and attending to carpenter complaints from all joinery works/cup boards etc including petty repairing wk with materials like nails/screws/beads/oil putty as per site requirement, Note: (i) Contractor or his authorised representative collect such type of complaints from B/R-II complaint cell at 8.30 AM on daily except Sunday & Holiday. No extra payment shall be made on account of collection of complaint. (ii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor.

Checking and attending to Mason complaints from all masonry works including petty repair wk with materials like Cement upto 5 Kg /Sand/White cement 200 gm per each complaint as per site requirement, after rectification it should be painted to match the existing colour and materials ll as per directed. Note: (i) Contractor or his authorised representative collect such type of complaints from B/R-II complaint cell at 8.30 AM on daily except Sunday & Holiday. No extra payment shall be made on account of collection of complaint. (ii) Complaints must be completed with in 24 hrs without any fail otherwise recovery shall be made double the market rate to the contractor.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 15mm complete all as directed.

S&F for 15mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 20mm complete all as directed.

S&F for 20mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantaling existing water tanks complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantaling existing water tanks complete all as specified and directed.

S&F in repairs ball valves of 20mm dia, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed, minimum weight - 210 gms of including taking down existing ball valves any type all as directed by Engr-in-Charge. Make : Prayag or equivalent as approved by GE.

S&F in repairs vitreous china wash hand basin white of size 800mm x 475 mm with and including PVC side cabinet and floor mounted cabinet of size 240x140x975 mm and 780x440x800 mm complete all as approved by Engineer-in-Charge. Make : Somany Cat Part No 10527 (Basin) & 16122 (Cabinet), 170114 (Mirror), 160121 (side cabinet) or equivalent of M/S Johnson, H & R India Ltd / M/S Hindustan sanitary ware and Industries Ltd / CERA, Hindware, Madhusudan Ceramic as approved by GE.

S&F (in repairs) vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified. (Make : Hindware/Cera as approved by GE).

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern EWC), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, CP jet nozzle, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & as directed. Make : “Cardiff Range” of Parryware equivalent of M/S Johnson, H & R India Ltd / M/S Hindustan sanitary ware and Industries Ltd / CERA, Madhusudan Ceramic as approved. by GE.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern EWC), coloured, Wall Hung Closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush Wall Hung flushing cistern of 10 litre capacity with lid, necessary Wall Hung Fittings complete all as specified & as directed.

S&F (in repairs) vitreous china squatting pan 'orissa pattern' size 580 x 450 mm white with integral foot rest (ISI marked) with 'P' or 'S' trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc, including setting of pan & trap in lean PCC 1:5:10 complete and making good to distrubed floor with PCC or cement mortar 1:3 to match with sorroundings all as directed.

S&F in repairs vitreous china wash basin white of size 550x400 mm with padestal stand (ISI marked) including 32 mm CP waste coupling & PVC flexible waste pipe of min 90 cm long, flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs all as specified and directed.

S&F in repairs vitreous china counter top basin size 450 x 525 x 195 mm shape ovel, Make: PARRYWARE / JAQUAR / SOMANY / HINDWARE / PRAYAG as approved by GE including 32 mm CP waste coupling & PVC flexible waste pipe of 90 cm long complete all as specified & directed.

S&F in repairs Jet spray PVC butterfly plated for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete. Make: Prayag

S&F in repairs health fusset chromium plated suitable for 15 mm bore pipe including 1 M long PVC tubes for EWC complete all as specified & directed by Engineer-in-Charge.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, complete all as specified.

S&F in repairs for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as directed.

S&F in repairs for PVC internal fittings (kit) complete for low level flushing cistern tank, all as specified and directed by Engineer-in-Charge. Make Commander/Perryware.

S&F in repairs for towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed by Engr-in-charge including taking down existing towel rail.

S&F in repairs towel Ring, Chromium plated, fixed with brass screws and wooden/plastic cleats as approved by the GE.

S&F in repairs CP toilet paper holder with cover complete all as specified and directed.

S&F in repairs waste coupling 32mm of PTMT (half or full threaded) (minimum wt 45 gms complete all as specified & directed.

S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed.

Supply and replacement in repairs of brass spindles, phases of brass of any size required 3/4/5 for bib taps, pillar cocks, stop cocks, angle valves, concealed valves complete all as directed.

S&F in repairs for MS grating CP 75/100mm dia, with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed.

S&F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly nuts, screwed for iron pipe etc complete as specified and directed.

S&F in repairs brass chromium plated shower rose with long arm 150mm size fixed to 15mm bore pipe all as directed.

S&F in repairs sink with draining board made out of stainless steel 1mm thick sheet for kitchen with plug, washers, waste pipe, cast iron centilever bracket, connecting union over all minimum size 915mm x 460mm with bowl size 410mm x 330mm x 160mm incl 32 mm PVC flexible waste pipe comjplete all as directed.

S&F in repairs waste coupling for sink as per sample approved comjplete all as directed.

S&F in repairs mirror cabinet (PTMT) fixed on wall with cadmium plated brass screws as per approved by GE all as directed.

S&F in repairs bib taps bore of pipe in 15mm, cast copper alloy, fancy type, chromium plated, with crutch or butter fly handle and aerating operation devices screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. (Make : Prayag/Cera/Marc).

S&F in repairs for bib tap standard of PTMT any colour 15mm bore high pressure screwed for iron pipe (Min. wt 90 gms) and complete all as specified and directed.

S&F in repairs 15mm bore, stop valve/angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repairs 15mm bore, two way angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in reapirs, 15mm bore, stop valve external threaded, chromium plated, fancy type, with long shank, and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repairs 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed

S&F in repairs PVC flexable waste pipe 32/40 mm dia & approx 900 mm long with PVC waste coupling suitable for WHB, sink & urinal complete all as specified & directed.

S&F in repairs brass chromium plated Towel Rack 600mm Long with Lower Hangers Prima Collection of make - Jaquar or equivalent of Marc / Parryware / Somany / Parko / Gem / Prayag as approved by GE) complete all as specified & as directed. Make :PRIMA collection or equivalent

S&F in repairs fancy type center hole basin mixer without popup waste system but including plain waste 32 mm size with aerator complete cast copper alloy, chromium plated, scrwed downhigh pressure, with long scrwed shanks & fly nuts scrwed for iron pipes of 15 mm bore complete all as specified & as directed. Make :PRIMA collection or equivalent

S&F in repairs brass chromium plated telephonic hand shower with 1.50m long stainless steel braided flexible tube with nut & nipple & hook suitable for wall mixer & screwed down for iron pipe of 15mm bore all as specified and as directed. Make :- Parryware/ hindware/cera/ Prima collection

S&F in repairs wall mixer chromium plated (3 in -1) with arrangement for both telephonic shower and overhead shower with 220 mm max long bend pipe with hand shower of size 100 x 55 mm with 130 mm long arm & 1.2 m house pipe of Prima Collection or equivalent make in Jaquar/Parryware complete all as specified & directed.

S&F in repairs brass CP Wall mixer for mixing hot & cold water suitable for 15mm bore dia pipe screwed down for iron pipe and fixed copmplete all as specified and directed.

S&F in repairs glass corner shelf (Cat Part No T6010A1 of make – Parryware or equivalent of Jaquar/Marc) complete all as specified & as directed.

Dismantling AC Pipe/ PVC pipes 110mm/ 75 mm dia

M&L machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified& directed by Engr-in-Charge.

M&L for taking down and removal of loose/disintegrated old concrete/plaster and applying and including 10mm thick bonding coat of modified styrene butadiene emulsion (SBR bonding agent i.e. Nitobond SBR 45) in proportion 1 (Nitobond SBR 45) : 1(water) : 3 (OPC) by volume with the brushes etc to bind new cement plaster/polymer modified plaster /concrete /screed concrete on old wall/ceiling surface etc complete all as specified and directed by Engr-in-Charge.

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with MS clamps as per site requirement complete all as directed.

S&F PVC (SWR) Vent cowl 75mm dia complete all as directed.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as directed.

All as per item No 141.00 here in before but fixed to walls with clamps complete all as directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) 75mm dia Floor Trap, plain with grating including jointing with solvent cement all as directed.

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed by Engineer - in - Charge. (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately).(iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately.) on top (vii) M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately) Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measered.