Balance Work of Laying Asbestos Cement Pressure Pipes by using old pipes already available with the department along with new pipes for Gangowal Lift Distributary Scheme 1 off taking at RD 2000 Mtrs and Scheme 2 off taking at RD 3590 Mtrs of Gangowal

Amount

Excavation by mechanical means (JCB or Hydraulic excavator ) in trenches for pipe lines with straight or open cutting in streets or open area including Earth work excavation for pipe lines trenches and pits 1.5mtrs . Depth in open area where disposal of surplus soil is done along with alignment including trimming and dressing sides leveling of beds of trenches to correct grade . Cutting joints holes, reflling and restoration of unmetalled or unpaved surface to as original condition excluding cost shoring of and timbering but encluding the cost of dewatering of rain water, diversion for traffic, night signals fixing caution boards,crossing over trenches for access to the houses , watching, fencing ,etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect including pick work (CSR item No. 28 .4)

Earthwork Upto 1.50 mtrs. Depth in ordinary gravel soil including pick work for

All classes of soil except rocky

Earthwork Exceeding 1.5 mtr. Depth But not exceeding 2.25 mtrs depth in ordinary gravel soil including pick work.

All classes of soil except rocky

Earth work in excavation in foundation, trenches etc. in all kinds of soil where pick and jumper work is not involved and not exceeding 2 mtr. Depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 m (6.6)

Providing and Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories along the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications 450mm

Providing and Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the ame into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications 500 mm

Providing and Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the ame into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications 600mm

Providing and Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the ame into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications 700mm

Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications (a) 350 mm

Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications (b) 450mm

Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications ( c )500mm

Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications (d)600mm

Stringing out cutting jointing and testing A.C. pressure pipes ISI mark as per IS1592-2003(class-15) with suitable AC coupling or C.I. D-joints with all accessories alongg the trenches and laying the same into the trenches to correct alignment and gradients including fixing C.I. bends,T- joints,reducers,sluice valves etc. including all carriage and testing complete in all respect and as per design and PWD specifications ( e ) 700mm

Providing and fixing double air valve ISI marked as per IS-14845 including jointing all carriages complete and testing complete in all respect and as per design and PWD specifications.

C.I. Double Air valve (size 100mm )

Providing and fixing C.I /D.I Flanged end , stem of SS (AIS 1410) and bronze (Gun metal ) Working parts sluice valves of special quantity make such as Kirlosker approved by Engineer-in - charge. I.S.I. marked 14846-2000 socketed or flanged, joiting with tyten joints including Jointing , Testing & Insertion sheet , all carriage to site of work and testing etc. complete In all respects (with the approval of Engineer-in-Incharge) as per desing and specification (CSR 28.24) Class PN-1 as per ISI

700 mm i/d sluice valves flanged

600 mm i/d sluice valves flanged

500 mm i/d sluice valves flanged

450 mm i/d sluice valves flanged

350 mm i/d sluice valves flanged

Providing and fixing reducers including carriage to site.testing complete in all respect as per design and specification.

Laying cement concrete 1:4:8 with stone ballast 20mm gauge mixing by mechanical means using concrete mixer volumetric type in foundation and plinth including supply and carriage of cement, sand and shingles from approved quarries to site of work completed in all respect. (CSR item No.10.11 (a) (i)

Laying cement concrete 1:2:4 with stone ballast or shingle mixing by mechanical means using concrect mixer volumetric type machine in foundation and plinth including supply and carriage of cement, sand and shingles from approved quarries to site of work completed in all respect.

Laying Ist class burnt brick work laid in cement, sand mortar 1:4 in foundation and plinth including supply & carriage of cement, sand and bricks from approved sources to site of work completed in all respect.

Plastering and Pointing

12.5 mm thick cement plaster

Centring and Shuttering

Shuttering for faces of concrete foundation and plinth beams(vertical or battering) including cost of all materials complete in all respects.

Filling sand including supply & carriage of fine sand complete in all respect.

Steel and Iron Work

Steel work, fixed independently Without connecting plates including cutting hoisting and fixing in position and cost of all materials complete in all respect.

R S Joists

Providing C.I. bends of different dia as per IS 5531 1998 different angles includings carriage to site of work includng supply and fixing of C.I.D. joints and testing etc. complete in all respect as per design and specifications.(a)600mm

Providing C.I. bends of different dia as per IS 5531 1998 different angles including carriage to site of work includng supply and fixing of C.I.D. joints and testing etc. complete in all respect as per design and specifications.(a)450mm

Supply and fixing of Tee Joints (IS 5531) including carriage to site work and testing etc. Complete in all respects as per design and specificatins.(a)700x700x200 mm

Supply and fixing of Tee Joints (IS 5531) including carriage to site work and testing etc. Complete in all respects as per design and specificatins.(b)600x600x200 mm

Supply and fixing of Tee Joints (IS 5531) including carriage to site work and testing etc. Complete in all respects as per design and specificatins.( c )500x500x225 mm

Supply and fixing of Tee Joints (IS 5531) including carriage to site work and testing etc. Complete in all respects as per design and specificatins.(d)450x450x225 mm

Supply and fixing of Tee Joints (IS 5531) including carriage to site work and testing etc. Complete in all respects as per design and specificatins.( e )350x350x160 mm

Providing C.I.D joints( long collar) with rubber ring and bold nut complete set as per IS:8794 Class 15 Complete in all respects as per design and specificatins. (a) 700mm

Providing C.I.D joints( long collar) with rubber ring and bold nut complete set as per IS:8794 Class 15 Complete in all respects as per design and specificatins. (b) 600mm

Providing C.I.D joints( long collar) with rubber ring and bold nut complete set as per IS:8794 Class 15 Complete in all respects as per design and specificatins. ( c ) 500mm

Providing C.I.D joints( long collar) with rubber ring and bold nut complete set as per IS:8794 Class 15 Complete in all respects as per design and specificatins. (d) 450mm

Providing C.I.D joints( long collar) with rubber ring and bold nut complete set as per IS:8794 Class 15 Complete in all respects as per design and specificatins. ( e ) 350 mm

Supply of AC couplor with EDT rubber rings complete in all respect as per design and specifications.(a)350 mm

Supply of AC couplor with EDT rubber rings complete in all respect as per design and specifications.(b)450 mm

Supply of AC couplor with EDT rubber rings complete in all respect as per design and specifications.( c )500 mm

Supply of AC couplor with EDT rubber rings complete in all respect as per design and specifications.(d)600 mm

Supply of AC couplor with EDT rubber rings complete in all respect as per design and specifications.( e )700 mm

Carriage of ACP pipes from Dholwaha colony Hoshiarpur to site of work complete in all respect. Lead approx 35 KM.(a)350 mm

Carriage of ACP pipes from Dholwaha colony Hoshiarpur to site of work complete in all respect. Lead approx 35 KM.(b)450 mm with six tyre truck with carriage boot of size width = 2.45 mtr., height = 1.70 mtr. Approx.

Carriage of ACP pipes from Dholwaha colony Hoshiarpur to site of work complete in all respect. Lead approx 35 KM.( c )500 mm with six tyre truck with carriage boot of size width = 2.45 mtr., height = 1.70 mtr. Approx.

Carriage of ACP pipes from Dholwaha colony Hoshiarpur to site of work complete in all respect. Lead approx 35 KM.(d)600 mm with six tyre truck with carriage boot of size width = 2.45 mtr., height = 1.70 mtr. Approx.

Carriage of ACP pipes from Dholwaha colony Hoshiarpur to site of work complete in all respect. Lead approx 35 KM.( e )700 mm with six tyre truck with carriage boot of size width = 2.45 mtr., height = 1.70 mtr. Approx.

Loading of Asbestos cement pipe into wagon trucks or boats within 15 meters lead complete in all respect.

Unoading of Asbestos cement pipe from non tipping bucket or boats including clearing 1.5 meters away from Rail or 6 meters away from the water edge complete in all respect.

any other item

Star construction company