Retender8201E

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debris out side MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Taking up or down 20mm bore, steel tubing galvanised along with fittings or any other type of pipe complete all as directed.

Taking up or down 25mm bore, steel tubing galvanised along with fittings or any other type of pipe complete all as directed.

Demolition and breaking up drain pipes of 100/75 mm dia(salt glazed ware,AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down shutters,exc 1 Sqm but not exceeding 2.0 sqm in each and refixing shutter in the same opening including easing & adjusting complete all as specified and directed.

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints including treating the timber libarally brushed at least twice with oil or kerosene based solusion of chlorophyrifos 20EC 1.0 % (by weight) concentration complete all as specified and as directed.

M&L for 35 mm thick 2nd class hard wood factory made glazed/gauzed skeleton shutters for door, open rebated and prepared to receive glass, gauze etc (without sash bars), edges framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc; size of the members of shutters as specified in SSR Part- I, Section 8, clause 8.24(a) complete all as directed.

S&F 30mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified. Make : - Kit Ply / Mysore Chip boards / Century Ply boards / Indian ply woods / Green Ply / Archid Ply

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick, sheet glass, figured/ pin headed glass and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S&F in repair stainless steel wire cloth 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F powder coated aluminium (Minimum thickness of powder coating 50 micron) frame work and shutters for doors, windows, ventilators, including partitions with extruded built up standard tubular section/appropriate Z section and other sections of approved make conforming to IS-733 and IS 1285 fixing with dash fasteners of required dia and size including necessary filling gaps at junction ie at top, bottom and sides with required EPDM rubber/neoprene gasket etc including providing and fixing hinges/ pivots. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat, angle, aluminium snap beading for glazing/ paneling, CP brass/ Stainless steel screws, rollers, handles, locking arrangement etc. complete all as specified. Note : (i) Glass panes will be measured and paid seperately. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will not be weighed and not paid seperately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

M & L for Mild steel framed work such as grills, gratings, door, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos fibre cement building board E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and directed by the Engr-in-Charge. Make :- Eternit Everest / lafarge/ Armstrong or equivalent as approved by GE

S & F in repair 4 mm thick non asbestos fibre cement building board E-board (plain), HSPC fixed to existing timber/GI/Aluminium framework with screws including providing two coats of white wash complete all as specified and directed by the Engr-in-Charge. Make :- Everest / lafarge/ Armstrong or equivalent as approved by GE

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for dark shade double charge Vitrified ceramic, designed, coloured tiles, Grade B I(b), 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles, Grade B II(a), 8 to 10mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic joint free, coloured tiles, 350x250mm/450x350mm, Grade B III, 7 to 8 mm thick as in dado/vertical surface of wall/ skirting including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in panels, finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F Mild steel small articles using flat iron such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290, Gde E-165 including retaining with tar or coat tar black paint complete all as specified and as directed.

M & L for Plain cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in filling of sunken floof, foundation filling etc complete all as specified and directed.

M & L for applying two coats of blown bitumen, any grade, applied hot in concrete surfaces at the rate of 1.50 kg per sqm

Providing cement concrete type B-1, 1:2:4 mix (using 20 graded stone aggregate) as in roof kerb, filling gap between roof sheet and wall and the like including necessary formwork.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceilings (sunshed, chajja, fins etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer including 2mm thick wall care putty complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes, Type 'B', single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 110 mm with access door complete all as specified and directed.

S&F PVC (SWR) junction single,(single T) 75 mm with access door complete all as specified and directed.

S&F PVC (SWR) branch piece single,(single Y) 75 mm dia equal or unequal with access door complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F 20mm CPVC ball valve brass insert complete all as directed.

S & F 25mm CPVC ball valve brass insert complete all as directed.

S & F in repair 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S & F in repair 25 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 455 gms) complete all as specified and directed.

S&F in repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long and 32mm dia flush pipe, S or P Trap & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make of Pan CERA Cat No S3010108 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern),P or S trap type, white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with white PVC seat and cover complete including making good damaged/disturbed surfaces complete all as specified and directed. Make PRAYAG Cat No 4125 or equivalent of CERA/Hindware/Parryware

S&F in repair Vitreous China Urinal, bowl type (approximate size 340X280X470mm), white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement mortar; fixing flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to urinal/flushing cistern, trap and waste pipe). Make : CERA Cat No S4020103/Prayag Cat No 4999 or equivelent of Parryware/Hindware

S&F in repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, including provision of chromium plated fancy type long neck pillar tap with capstan head suitable for 15 mm bore pipe, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, 45 cm long PVC connections including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2040105 or equivelent of Parryware/Hindware/Prayag

S & F in repair 32mm dia, not exc 1.00 metre long, low density polyethelene (LDPE) pipes of pressure rating 6 Kgf/Sqcm with connecting brackets for wash basin/urinals complete all as directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe 32mm dia, float and handle including PVC connection pipe of 15mm dia, 600mm long, brackets complete all as specified and directed.

S & F in repairs PVC connection pipe with PTMT nuts, 450mm long. Make: CERA/Hindware/Parryware/PRAYAG

S & F in repair 15 mm bore, bib taps, cast copper alloy with crutch or butterfly handle, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 2 way 15 mm bore bib taps with double handle quarter turn fancy type with flange cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO F1018163 or equvelent of Make Hindware/Parryware/PRAYAG

S & F in repair 15 mm bore, stop/angle valves, cast copper alloy with crutch or butterfly handle , screwed down, screwed both ends for iron pipe or for union/brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware/PRAYAG

S&F in repair 15 mm bore, any colour, PTMT, bib taps high pressure with capstan head screwed down to iron pipe complete all as specified and directed (Minimum weigh 90 gms). Make: PRAYAG Cat No 121 or equivelent of POLYTUFF

S&F in repair 15 mm bore, any colour, PTMT, stop valve high pressure with capstan head screwed down to iron pipe complete all as specified and directed (Minimum weigh 90 gms). Make: PRAYAG Cat No 121 or equivelent of POLYTUFF

S&F in repair 15 mm bore push tap of any colour high pressure, PTMT, screwed for iron pipe complete all as specified and directed (Minimum weigh 47 gms) Make: PRAYAG or equivelent of POLYTUFF

S&F in repair 25 mm dia stainless steel metalic coated curtain rod with ring brackets etc complete all as specified and directed

S&F in repair stainless steel curtain rod bracket suitable for 25mm dia curtain rod including wooden support etc complete all as specified and directed

S & F in repair shower rose PTMT with arms with or without swivel joint, 125mm size including fixing to iron pipes complete all as specified and directed. (Minimum wiegh 40 gms) (Make: PRAYAG or equivalent of Polytuff)

S & F in repair stainless steel soap dish, 150mm, fixed to wall with chromium plated screws complete all as specified and directed. Make : CERA Cat No F5007106 or equivalent of Hindware/Parryware/Prayag

S & F in repairs brass, chromium plated, 15mm bore wall mixer with L bend for mixing hot and cold water, screwed down with provision of over head shower and cock for iron pipe and fixed complete all as specified and directed. Make: PRAYAG Cat No BS -31/ CERA Cat No F7020302CH or equvelent of Make Hindware/Parryware/CERA

S & F in repair health faucet ABS body including wall hook, cast copper alloy & 1.25 metre long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed. Make CERA Cat No F 8030104AB or equvelent of Make : Hindware/Parryware/Prayag

S&F in repair towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190 gms) complete all as specified and directed.

M&L for cleaning existing PVC tanks of any position or at any hight of any description, capacity 500 ltr, removing all scale and dirt/dust from existing PVC tank including cleaning mouth of circulating pipes ie inlet-outlet, overflow pipe etc complete all as specified and directed

M&L for cleaning existing PVC tanks of any position or at any hight of any description, capacity 1000 ltr, removing all scale and dirt/dust from existing PVC tank including cleaning mouth of circulating pipes ie inlet-outlet, overflow pipe etc complete all as specified and directed

M&L for cleaning existing PVC tanks of any position or at any hight of any description, capacity 2000 ltr, removing all scale and dirt/dust from existing PVC tank including cleaning mouth of circulating pipes ie inlet-outlet, overflow pipe etc complete all as specified and directed

sri vasavi constructions