138WE/L-154/2025-26

Amount

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exc 15cm thick (below or above ground level ) and removing debris off the premises complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris off the premises, complete all as specified and/or as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) etc. any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.

Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.

Taking down cement plaster on brick/ PCC block or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc., complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking of shutters from the frame) not exc 1.5 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 sqm each but not exc 4 sqm each any type of door (wooden, aluminium & steel etc.) complete all as specified and/or as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and/or directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by Engr-in-Charge.

Dismantling boarding/ wooden flooring of any description, fixed in any position, complete all as specified and/or directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing), removing rubbish off the premises complete all as specified and/or as directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in sub base of floor complete all as specified and/or as directed by Engr-in-Charge.

M&L for vitrified ceramic tiles 10mm thick (light shade) (square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and/or as directed by Engr-in-Charge.

M&L for Non - skid coloured Ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and/or as directed by Engr-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces of size 450x350x7mm/ 350x250x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortar (1:4) as in backing coat complete all as specified and/or as directed by Engr-in-Charge.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 complete all as specified and/or as directed by Engr-in-Charge.

Demolition of reinforced cement concrete in ground floor and pavings not exc 15cm thick below or above ground level complete all as specified and/or as directed by Engr-in-Charge.

M&L Form work to soffits of suspended slabs such as roof, floor slabs, landings etc not exc. 200mm thick (horizontal or sloping) complete all as specified and/or as directed by Engr-in-Charge.

M&L for reinforced cement concrete 1:2:4, type B1 (20 mm graded stone crushed aggregate) nominal mix as in beam cantilevers, bressummers, lintels over 1.5 m span complete all as specified and/or as directed by Engr-in-Charge.

M&L for TMT mild steel bars, 10 mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9 mm dia), complete all as specified and/or as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 5 mm dia and over up to 10mm as in reinforcement cut to length bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia, complete all as specified and/or as directed by Engr-in-Charge.

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated, including backing with thermocol sheets or as specified by manufacture all as specified and directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding including dismantling complete all as specified and as directed.

All as per serial item No 25 above, but as in ceiling.

M&L 6mm (5 ply) thick veneered decorative (Knotty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work as in wall, complete all as specified and as directed.

All as per serial item No 27 above, but as in ceiling.

M&L for not less than 15mm thick wooden battens of 100mm wide fixed each other with male and female grooves fixed with screws to timber frame work as in wall panelling, shelves/ boarding complete all as specified and as directed.

All as per serial item No 29 above, but as in ceiling.

M&L French polishing on wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler new surface with two or more coats to obtain the required finish, complete all as specified and/or as directed by Engr-in-Charge.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and/or as directed by Engr-in-Charge.

M&L Prelaminated particle board 18/19 mm thick both side interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and/or as directed by Engr-in-Charge.

S&F Piano/continuous hinge of size 40 mm (when open) stainless steel complete all as specified and as directed.

S&F 125mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and/or as directed by Engr-in-Charge.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for cabinet shutters complete in all respect and fixed in position complete all as specified and/or as directed by Engr-in-Charge. Make : KAFF/Hettich or equivalent approved make as approved by GE.

S&F tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished complete fixed in position all as specified. Make : Harrison (Cat No 0812) or equivalent approved make as approved by GE.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine) or equivalent approved make as approved by GE.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified. Make : Hettitch or equivalent approved make as approved by GE.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified. Make : Harrison (Jasmine) or equivalent approved make as approved by GE.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as plinth protection finished even and smooth with out using extra cement, complete all as specified and/or as directed by Engr-in-Charge.

M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.

M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

M&L precast solid blocks in cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

All as per serial item No 46 above, but except block.

M&L for 10mm thick rendering on other than fair faces of block/ brick wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and/or directed by Engr-in-Charge.

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 including mixing of liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of primer complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of new plastered wall surface of any description and applying three coats of white wash complete all as specified and/or as directed by Engr-in-Charge.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and/or as directed by Engr-in-Charge.

S&F 35mm thick 2nd class soft wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.

S&F 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels commercial type on both sides, complete all as specified and/or as directed by Engr-in-Charge.

S&F 2nd class soft wood 35 mm thick Glazed and Skelton shutter, open and prepared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured separately) complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of new untreated wood or wooden based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and/or as directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and/or as directed by the Engr-in-Charge.

M&L for powder coated aluminium door shuttlers, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, hinge type B-21 100 mm longs (3 Nos) suitable handle (2 Nos) (Glass / Wiremesh should be measured separately) complete all as specified and/or as directed by Engr-in-Charge.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (3 Nos) suitable handle (1 No) etc. complete all as specified and/or as directed by the Engr-in-Charge.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F in repairs 5.0mm thick figured glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed including hacking out old glass. complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F in repair aluminium (Die cast) body door closer hydraulically designation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg all as specified and directed

M&L for aluminium (extruded section body) door closer hydraulically regulated designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed completed all as spd and directed.

S&F floor door stopper (length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed.

S&F MS Rolled sections in main and cross beams, hip and jack rafters ;purlins where connected to common rafters running rails and guides for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F Plates Fe-410W (Gde E-250) Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated, complete all as specified and as directed.

M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width/ girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and/or directed by Engr-in-Charge.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs all as specified and as directed by Engr-in-charge.

Taking up or down existing steel/PPR tubing and connections, 25 or 32 mm bore of pipe and connections in any position including cleaning for refixing or removal to store complete all as directed by Engr-in-Charge

S&F 25mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge.

S&F 32mm dia 3 layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge.

S&F in repair 25mm outer dia PPR Gate valve (Brass insert) confirming to ISO 2000 high pressure with epoxy coated aluminium rod and high density plastic ball screwed for PPR pipe or for union and fixed as per requirement of site complete all as specified and/or as directed by Engr-in-Charge.

Dismantling water tank exc 250 & not exc. 500 litre and removing to store complete all as specified and/or as directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, complete all as specified and/or as directed by Engr-in-Charge.

S&F rotational moulded HDPE water storage tanks 500 ltrs capacity and will be PUF insulated with 75mm thick PUF insulation of density 48kg/Cum (cylindrical vertical type/rectangular loft type closed top) hoisted and fixed in position all as specified and directed by Engr-in-Charge.

S&F chromium plated brass paper holder, complete all as specified and as directed.

S&F in repairs sink with drain board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs sink cock wall mounted with swinging spout and with wall flange, fancy type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed. Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)

S&F in repair one Piece EWC with built in Cistern Vitreous china wash down water closet (Pedestal), white (EWC) including Plastic seat of same colour of WC, closed pattern with flat bottom, and cover with mild steel chromium plated hinging device complete with flushing cistern. Make : Cat Part No Cruiser S1013137S Trap 300 mm or equivalent approved make as approved by GE.

S&F in repairs CP health faucet ABS with double lock 1.2 mtr CP tube stainless steel flexible hose and wall hook all as specified and as directed.

S&F CP toilet jet spray ABS with double lock 1.2 mtr CP tube stainless steel flexible hose all as specified and as directed.

S&F sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F sheet glass basin shelf assembly consisting of 8mm thick glass shelf 600 x 150mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F chromium plated soap dish any type fixed to plugs with brass screws, complete all as specified and directed.

S&F in repairs fancy type 15 mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)

S&F in repair angular stop Cock, fancy type with wall flange, fancy type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified. Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)

S&F in repair towel rod CP 60 cm long between flanges and including all accessories like brackets/ screws etc. as recommended by manufacturer and complete fixed in position complete all as specified.

S&F in repair PVC connections 15mm size with brass nuts of length 450mm complete all as directed and specified.

S&F Vitreous china counter base wash hand basin white minimum size 500X420x160mm including chromium plated brass coupling, bottle trap, 600mm PVC braided connection (two number), angular stop cock, (Valve) (two number) complete all as specified and/or as directed. Make : Cat Part No COLGA S2030132 of Cera or equivalent approved make as approved by GE.

S&F vitreous china urinal half stall type, white complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60 mm brass screws, pointing around urinal back in cement, fixing grating and union for discharge pipe excluding flushing cistern, flush pipe but including CP waste coupling, PTMT urinal spreader, etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore CP wash basin mixer for mixing hot & Cold water copper alloy fancy type high pressure screwed for iron pipe complete all as specified and directed. Make : Cat Part No F1013452SINGLE of Cera or equivalent approved make as approved by GE.

S&F 32 mm dia PVC waste pipe for wash hand basin/ Kitchen sink etc. complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F in repairs PVC (HDPE) SWR pipe 110 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacturer's instruction, laid in trenches or in floor complete all as specified and directed by Engr-in-Charge. Make : Astral / Prince / Finolex

S&F in repairs 110 mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints, fixed to walls and vent pipe as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repairs PVC(HDPE) SWR pipe 75 mm bore, single socketed in any length with rubber ring joints using solvent as per manufacture instruction, laid in trenches or in floor complete all as specified and directed by Engr-in-Charge. Make : Astral / Prince / Finolex

S&F PVC (SWR) 75 mm dia floor trap with plain with grating including jointing with solvent cement complete all as specified and directed.

S&F grating doom 75mm dia of PTMT (min weight 25gms) complete as specified and directed

S&F PVC (SWR) 110 mm bore vent cowl complete all as specified

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100mm bore pipe line complete all as specified and as directed by the Engineer-in-Charge

Taking down carefully copper/ aluminium point wiring (light, fan, socket and power point) including complete fittings such as switches, ceiling rose, regulators, socket etc. and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and/or as directed by Engr-in-Charge.

Taking down carefully sub main wire any size, complete all as specified and/or as directed by Engr-in-Charge.

Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts FRLS cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor FRLS cable as continuous earth lead all as specified and directed for the following:-

One light/exhaust fan point controlled by one way switch.

One switch socket outlet 6 Amps, 230 volts point on same board.

One switch socket outlet 6 Amps, 230 volts point on independent board.

All as item No 120 above, but using cables 4 sqmm size.

S&F in replacement of lamp holder insulated body with back plate complete all as specified and directed.

S&F switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed.

S&F socket outlet two in one 5 pin 6 Amps flush type.230 volts complete all as specified and directed .

S&F switch socket combination out let two in one 5 pin 6 Amps flush type 230 volts complete all as directed.

S&F switch socket combination 2 in 1, 5 pin, 6 and 16 Amp flush type universal outlet multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as directed.

S&F ceiling rose, surface Bakelite three terminals complete all as directed.

S&F in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways all as specified and directed.

S&F MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or directed by Engr-in-Charge. Make : Cat Part No DHMGCSNF040 of Havells or equivalent in approved make as approved by GE.

S&F MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge. Make : Cat Part No DHMGCSPF006-032 of Havells or equivalent in approved make as approved by GE.

M&L for submain wiring along with earth wire FRLSH insulated copper conductor, single core cable in surface/recessed as required in & including PVC casing caping wire size 2 x 6 sqmm + 1 x 6 sqmm earth wire complete all as specified and directed.

S&F in replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.Make-Havells /crompton/ Bajaj

S&F in replacement LED luminaire 600mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed. Make-Havells/ Philips/crompton/ Bajaj

S&F in repair connecting and testing LED security light fitting 35 watt, 230 volt, AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp and bracket with impact and corrosion resistant incl thermal management in multiple optics complete with IP65/66 protection complete all as specified and directed.

S&F in repair Air Circulator fan, steel body AC single Phase 230V of size 300mm sweep with blades, and frame and louvers complete all as specified and directed. Note :- Old UNSV retrieved fans should be deposited with MES store yard.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and including 4 mm dia GI wire as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 3 of MES SSR Part I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and directed.

Horizon Construction Company (BID ID -3467786)