REPAIR REPLACEMENT OVERHAULLING OF FIRE FIGHTING SYSTEM AND CERTAIN REPAIR TO FIRE PUMPS AND MOTORS AND CONNECTED WORKS UNDER AGE EM II IN GE C KIRKEE

Amount

Taking up cast iron water mains / MS ERW pipes / DI pipe size upto 200 mm dia (including all fittings), with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed at site.

M & L for MS ERW Pipes of size 200mm including all fitting in any lengths & welding , cutting , bending etc complete laid in trenches/on wall all as specified and directed .

M & L for MS ERW Pipes of size 150mm including all fitting in any lengths & welding , cutting , bending etc complete laid in trenches/on wall all as specified and directed .

M & L for MS ERW Pipes of size 80mm including all fitting in any lengths & welding , cutting , bending etc complete laid in trenches/on wall all as specified and directed .

M&L for DI pipes 200mm bore, class K-9 spigot and socket end suitable for rubber ring tyton joints including jointing & jointing material, rubber ring all incl as directed by the Engineer-In-Charge.

Ditto all as per item No- 5.00 above but 150mm bore.

Ditto all as per item No- 5.00 above but 100mm bore.

S&F DI Pipe fittings, specials, bends and type, reducer and angle tapers, any stright bends double socket etc , Tee pipes single branch all socketed and spigot CI upto 200mm dia including dismantling of old one all as specified and as directed.

Supply & Fix in replacement of single type fire hydrant landing valve type A Single headed outlet of 63mm dia incl rubber gasket, nut & bolts complete all as specified and directed by Engr-in-charge.

Supply & Fix in replacement of double type fire hydrant landing valve type A Double headed outlet of 63mm dia incl rubber gasket, nut & bolts complete all as specified and directed at by Engr-in-charge.

Supply and Fix in replacement of Branch pipe gun metal 63mm instantaneous inlet, made threaded outlet, 15mm bore nozzle short all as specified and directed

Supply and fix in replacement of 63mm dia 15 mtr long hose confirming to IS 636 complete with male and female coupling complete all as specified and directed. Note For item No 01 to 12 - (i) Contractor should visit the site before quating the tender and any other misc items required for complete the job are deemed to be incl in to rate quated by contractor.

Supply and Fix in replacement of Hose box Out door type of size 800x600x250mm made out of minimum 1mm thick MS sheet with double door with 4mm thick plain sheet glasses and door frame made of 1.2 mm thick MS sheet painted fire red outside and brilliant white inside complete fixing nut bolts etc all as specified and directed

All as per item Ser No 13.00 above but indoor type -ditto-

Supply and Fix in replacement of Flanged stand post CI of 80mm dia 1.5m height as per existing all as specified and directed. Note (a) Any demolation of pcc work and new pcc work if needed for complete the job is mesured and paid sepratelly.

Supply, installation, commissioning and testing of photo electric heat detector in replacment with twist lockable removal base, with connector for looc in and out, insect resistant screen and rotary/binaary in tamper resistant features incl connections etc as per specification and as directed by Engr-in-Charge at site

Supply, installation, testing and commissioning of optical thermal detector (Heat & smoke) radio-linked optical thermal detector operates both with an optical sensing chamber based on the principle of scattered light as well as with a rate of rise thermal sensor. The detector communicates with a fire detection control panel in loop technology via the Loop RF interface.Two lithium batteries are accommodated in the detector base one as backup. The two coloured LED indicator with 360 visilibility. Mechanical theft protection in the base. Radio transmission of 150 mtr (in free air), operating at De-licensed frequency range of 865 MHz- 867MHz or 433 MHz (Approved Make:- HFP/Hochiki/Edwards /Notifier) (Model No- RMD-E-IN)

M&L for replacment of Lithium battery CR 2032, 3 Volts suitable for thermal detector including cleaning complete detector and make funtional all as directed by Engr-in-Charge at site.

M&L for replacment of battery CR 123, 3 Volts suitable for thermal detector including cleaning complete detector and make funtional all as directed by Engr-in-Charge at site.

Demolition and Dismantling of cement concrete in ground floors and pavings of any description and in any positon below or above ground level including throwing of materials at low lying areas at a distance of min 500m complete all as specified and directed at site.

Material and labour for Plain cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) for foundaton of motors filling in road cuttings, Hard standing including use of necessary form works for rough finished surface and making arrangements for fixing of bolts and nuts for Motors complete all as specified and directed at site.

S&F fabricated MS bracket /supports for MS and CI Pipe line, made out of angle iron and flat iron including bolts, nuts, washers and painting with two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5 m wide n.exc 1.5 m in depth for laying of pipe etc and getting out in Soft/Loose soil complete all as specified

Excavation in trenches n.exc 1.5 m wide n.exc 1.5 m in depth for laying of pipe etc and getting out in hard/dence soil complete all as specified

Returning filling in, trenches around pipe line including spreading levelling in layers n.exc 25 cm after laying pipes and well ramming all as specified and directed

Removal of surplus excavated soil to a distance n.exe. 50 mtr away from site and deposited where directed at a level not exceeding 1.5 mtr above the ground level all as specified and directed

Supply and Fix Sluice Valve 63 mm bore size type 1.6 PN with MS Spindle including taking out old sluice valve complete all as specified and directed

Supply and Fix Sluice Valve 200 mm bore size type 1.6 PN with MS Spindle including taking out old sluice valve complete all as specified and directed

S&F cast iron specials, bends and type, reducer and angle tapers, any stright bends double socket etc , Tee pipes single branch all socketed and spigot CI upto 150mm dia including dismantling of old one.

M&L for rectification of defective run lead joint of 300 to 400mm dia pipe line by burning out lead joint in position including recovering lead and making new lead joint all as specified including bailing out water coming from defective joints by means of electric/diesel driven pump set, testing of the joint under full working pressure for the following CI/GI Pipe lines all as directed by Engineer-in-charge.

All as per item no 30.00 above but of pipe size 150 to 250mm dia

All as per item no 30.00 above but of pipe size 80 to 100mm dia

M&L for rectification of defective rubber gasket flanged joints of pipe size 150 to 200mm dia including replacing rubber gasket, bolts, nuts and washers for CI/GI pipe line.

All as per item no 33.00 above but of pipe size 80 to 100mm dia

Supply and Fix in replacement cast iron Foot valve of size 80mm dia with rubber gasket and nut, bolts complete all as specified and directed .

Supply and Fix in replacement cast iron Foot valve of size 200mm dia with rubber gasket and nut, bolts complete all as specified and directed

M&L for cutting,clearing bushes/small plants and grass surrounding the E/M installations and removing the debris to a distance of 50m complete all as specified.

M & L for Construction of masonry valve chamber, 100 mm thick foundation using PCC 1:4:8, type D-2, over 15cm thick hard core, 20cm thick solid block masonry with blocks cast using PCC 1:3:6, type C-1, set in cement mortar 1:4, 15MM thick plaster to internal surfaces and external surfaces up to 15cm below ground level and top of floor in cement and sand mortar 1:4, finished even and smooth with out using extra cement , 3.15mm thick MS sheet cover including 50mmX50mmX6mm thick MS angle frame fixed in PCC 1:2:4, type B1 coping with 25mmX6mm flat iron hold fasts, handle, hinges with locking arrangements, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of surplus soil to a distance not exceeding 50M complete all as specified and directed.

Supply & fixing of MCCB 400 Amps 36KA, TP with Adjustable thermal magnetic release with spreader links etc in the control panels including dismantling of old one complete. Make :- L&T/ABB/Legrand

Supply & fixing of MCCB 125 Amps 36KA, TP with Adjustable thermal magnetic release with spreader links etc in the control panels including dismantling of old one complete. Make :- L&T/ABB/Legrand

Supply & fixing of Power contactor 300 Amps, 3pole AC3, coil voltage 230V AC. Make :- L&T/SIEMENS/Legrand

Supply & fixing of Power contactor 70 Amps, 3pole AC3, coil voltage 230V AC. Make :- L&T/SIEMENS/Legrand

Discoupling/Disconnecting and taking down carefully Electric driven pumping set of capacity 270HP from foundation after disconnectingsuction and discharge line taking down from foundation bolt dismantling from base channel and transporting to civil workshop for repair. Strip opening all parts , cleaning overhauling comprising of repairs/replacement of repairable parts , such as taking out impeller shaft assembly complete taking out bearing housing , gland bush and other connected items including balancing of impeller shaft , impeller and including lathe work a required , reassembling the complete pumping set , reinstalling , mounting and fixing on base channel on existing foundation and coupling properly to existing motor with proper balancing and alingment including recoupling of suction and discharge line , commissioning and testing on full load all as specified and directed.

M&L for MS coupling with suitable size of key for pump of capacity 270 HP Pump

M&L for Bearing housing MS with cover suitable for pump of capacity 270 HP Pump

M&L for Gasket set suitable suitable for pump of capacity 270 HP Pump

M&L for Gland bush (shaft sleeves)suitable for pump of capacity 270 HP Pump .

M&L for Gland Plates suitable for pump of capacity 270 HP Pump

M&L for MS Shaft for pump of capacity 270 HP Pump .

M&L for replacement of bearing suitable as existing for electric motor and pump of capacity 270 HP

M&L for distance bush brass suitable for pump of capacity 270 HP Pump

M&L for balancing of existing Brass/MS impeller for pump of capacity 270 HP Pump

Discoupling/Disconnecting and taking down carefully Electric driven pumping set of capacity 75HP (motor and pump) from foundation after disconnectingsuction and discharge line taking down from foundation bolt dismantling from base channel and transporting to civil workshop for repair. Strip opening all parts , cleaning overhauling comprising of repairs/replacement of repairable parts , such as taking out impeller shaft assembly complete taking out bearing housing , gland bush and other connected items including balancing of impeller shaft , impeller and including lathe work a required , reassembling the complete pumping set , reinstalling , mounting and fixing on base channel on existing foundation and coupling properly to existing motor with proper balancing and alingment including recoupling of suction and discharge line , commissioning and testing on full load all as specified and directed. Note for item no 43 and 53 :- (i) New spare parts will be measured and paid separately under relevent items (ii) Rates are deemed to be included for replacement of gaskets, packing with bearing grease, glands with graphite packing , nuts bolts , washers etc. (iii) Cost of transportation shall be deemed to be included in the rate quoted for these items. (iv) While taking out pump for repairs , the contractor will make arrengement pluging suction and discharge line with dead flanges, so that pumping of installation is not disturbed and there is no leakage of water. (v) The contractor shall repair and refixing the pump set within sevendays from the date of opening and making it functionable. Complaint will be notified to contractor on mobile phone at any time between 0800 hrs to 2200 hrs and defect,s will be rectified within sevendays after notification, failing which Rs 500/- per day will be recovered (vi) Contractor shall provide six month gurranty for all replaced spare parts of pumps.

M&L for replacement of MS shaft suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Impeller bush brass suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Brass Impeller suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Bearing housing with bearing of existing size suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Gasket set suitable suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Gland plates MS (As per sample) suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of Gland bush (As per sample) suitable for pump of capacity 75 HP for Becon pump type DRC-150/150. (Make as per sample).

M&L for replacement of MS Coupling suitable for pump of capacity 75 HP for Becon pump type DRC-150/50. (Make as per sample).

M & L for painting of motor & pump for removing the existing deteriorated paint by scrapping the complete body along with foundation of Pump and Motor and filling the cavities with filter spray painting with Anti corrosive paint, two coats over a coat of red oxide and marking of SM/MES No. with black paint for capacity 30 to 270 HP

M & L for removing the existing defective sluice valve spindle with check nut of any size and type from existing sluice valve of size 100 mm to 250 mm dia and replacement with new sluice valve spindle with check nut complete incluiding new nut,bolts and gland packing as per existing complate all as directed. Note - (i) The contractor shall repair and refixing the spindle assembly within two dayys from the date of opening and making it functionable. (ii) Complaint will be notified to contractor on mobile phone at any time between 0800 hrs to 2200 hrs and defect,s will be rectified within two days after notification, failing which Rs 500/- per day will be recovered (ii) Contractor shall provide six month gurranty for all replaced spare parts of sluice valve.

Supply , laying,commissioning and testing PVC insulated , round sheathed multi core heavy duty industrial cable copper conductor, 1100 volt cross sectional area 185 Sqmm 3 core incl lugs and removing unserviceable/old cable complete laying in cable duct all as specified and as directed. Make: Polycab/Finolex /Paragaon/Havells

M & L For preparation of the old painted surface of 80 to 200 mm bore CI/GI/MS Pipe and applying two coats of synthetic enamel paint in different colours as per colour code complete all as specified and directed by Engr-in-Charge.

M&L for replacement of Mechanical joint coller coupling long sleeve with rubber washer, mild steel screw bolts (machine made) with both ends screwed of dia as per flange hole and required length each screwed end to be fitted with washers and hexagonal nut suitable for 150mm CI/DI/MS pipe complete all as directed.

M&L for replacement of Mechanical joint coller coupling long sleeve with rubber washer, mild steel screw bolts (machine made) with both ends screwed of dia as per flange hole and required length each screwed end to be fitted with washers and hexagonal nut suitable for 200mm CI/DI/MS pipe complete all as directed.

Dismantling and taking out fire extinguisher CO2 type 45 Kg capacity from the bank system by removing discharge hose nozzles and transporting to approved testing Lab/workshop and carry out complete over hauling of cylinder, plunger nozzles, burst disc, safety plug, sealing washer, pneumatic valves, non return valves etc including purging, High pressure testing and refilling the cyclinder upto 45kg net CO2 all as per IS 2878-2004 and other relevant latest IS Standards complete including one coat of synthetic enamel paint on the cylinder with appropriate colour, labelling and transporting back to site, installing on its existing position and testing for satisfactory operation all as directed by the Engr-in-charge.

--- Ditto--- All as item no - 68.00 above but of capacity 30 Kg. NOTE For item no- 68.00 and 69.00 :- (a) Necessary test certificate on high pressure testing refilling shall be obtained from the testing/refilling auth and produced in original from the govt approved lab to the Eng-in-charge. (b) The extinguisher will be weighted at site to ensure correct refilling and the cost on this account shall deemed to have been included in the rate quoted for item No.1 above. (c) The rate quoted shall include replacement of minor parts such as nut bolts, washers etc for extinguisher. (d) Transportation of the cylinder shall be carried out with all precautions as laid down as per the safty norms of local authorities. (e) Any loss / damage to the govt property while executing the work is to be beared by the contractor himself. (f) Contractor may visit the site and get the system understood or studied before quoting the rates in the tender. (g) Repair/Overhauling includes complete insitu checking, cleaning, pressure testing, including rectification of defects or leakages and painting with approved paints etc to the banking system excluding fire extingushers. (h) Replacement of major parts for the banking system shall be measured and paid for separately.

Repairs/servicing and overhauling of complete fire bank system suitable for 5 Nos of 45Kg CO2 type fire extingushers including cleaning, pressure testing, rectification of leakages. Painting (one coat of synthetic enamel paint) in respect of all accessories/parts such as collecting pipe, distribution pipe up to 2'' for designed working pressure, checking of operating leverage, safety pipe, changing of wire tackles, adjusting the pulley, roller and wire ropes, etc and testing complete for smooth operation all as directed by the Eng-in-charge.

Repairs and overhauling of fire bank system suitable for 10 Nos of 30 Kg CO2 type fire extinguisher including cleaning, Pressure testing, rectification of leakages for distribution pipe line up to 2'' for designed working pressure, checking and oiling of operating leverage, safety pin, charging of pressure gauge - 01 No with and including one coat of synthetic enamel painting and testing complete for smooth operation all as directed by the Engineer-in-charge. Note for item no - 70 and 71. (a) Contractor may visit the site and get the system understood or studied before quoting the rates in the tender (b) Any Mishappening/Damaged occured to the govt property during execution of work contractor has to make it in his own cost.

Dismantling Nitrogen gas cyclinder 01 no from the system and carry out complete overhauling of cyclinder , plunger nozzels, pneumatic valves including high pressure testing and refilling the cyclinders with nitrogen gas complete including one coat of synthetic enamel paint on the cylinder with appropriate colour, labelling and transporting back to site, installing on its existing position and testing for satisfactory operation all as directed by the Engr-in-charge. Note for Item No 68 to 72: Contractor has to visit the site before quoting the tender and any other misc requirements and spares for completion of Job is deeemed to be included in the rates quoted and no other payments will be entertained on this account.

Taking out old unserviceable Pneumatic valve for existing Co2 cyclinder of capacity 45 Kgs and supply & fix new valve having techinical parameters as under:- all as per the directions given by Engr-in-charge Material - Brass Design temp - -25o C to +45oC Type of Operation - Pneumatic type Working pressure - 155 bar Test pressure - 236 bar Min brusting pressure - > 420bar

--- Ditto--- All as item no - 73.00 but of capacity 30 Kg.

Taking out unserviceable old rubber discharge hose pipe and supply & fix new hard type rubber hose suitable for fire extingusher CO2 type 45 Kg flooding system all as per existing hose including provision of hose nozzles on both ends having techenical paramaters as under :- complete all as directed by Engr-in-charge. Material - Wire Breaded hose Design temp - -25o C to +70oC Type of Operation - Pneumatic type Working pressure - 60 bar Test pressure - 90 bar Min brusting pressure - 350 bar

--- Ditto--- All as item no - 75.00 but of capacity 30 Kg.

Supply and fix discharge nozzle with aluminium body with designed temp -25oC to +70oC suitable for high pressure fire banking system complete with necessarry rubber packing on joints inclding dismantling the old washers and nozzels complete all as directed by Engr-in-charge.

Supply and fix ball valve with flanged and stainless steel body and MS handle 32mm bore with relevant IS suitable for high pressure fire banking system containing 10 Nos of 45Kg CO2 type fire extinguishers complete with necessarry rubber packing on joints inclding dismantling the old washers, cable valve and shiffting to store all as directed by Engr-in-charge.

metro electrical services

AN-ICON Engineering Technologies And Infrastructure Developments Pvt. Ltd