PROVN OF PARKING SHED AND HARDSTANDING AT CHINAR COMPLEX AT BB CANTT SRINAGAR

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in any type of soil complete all as specifed and directed.

M&L for PCC (1:3:6), Type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Designing providing and fixing 6mm thick Aluminium Composite Cladding over RCC/ Brick surfaces either segmental/ straight in plan wherever specified with extruded aluminium U sections, angle, cleats, weather sealants, backer rods of required size stainless steel screws, rivets, brackets, drilling and fixing the cladding to either masonry or reinforced cement concrete as the case may be manufacturer's specifications, complete the work in all respect including all necessary accessories. At all soffits aluminium cladding shall be bend 90 degree and joints at corner or edges will not be acceptable. On horizontal surface, the size of sheet should be maximum available of size complete all as per manufacturer's specifications and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 9mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and directed.

S&F 2nd class soft wood Plain fillets. square, rectangular or triangular in section, clean sawn, fixed with screws sectional area exc 13 but n. exc 25 Sqcm complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil, comlete all as specified and directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all specified and directed.

M&L for 75mm thick PCC (1:4:8), Type D-2 (using 40mm graded crushed stone aggregates) as in sub base of floors etc. complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Chequered cement concrete tiles with grey cement and pigments 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified & directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. all as specified & directed.

M/S Himalayan Construction and Co. (BID ID -3142250)

M/S BASHIR AHMAD MIR (BID ID -3143196)

M/S PARVEZ AHMAD LONE (BID ID -3141089)

M/S AIJAZ ENTERPRISES (BID ID -3147802)

M/S T A ENTERPRISES (BID ID -3141289)

M/S SHIMAR STAR GLACIER (BID ID -3148077)

M/S NORTHERN ELECTRICAL WORKS (BID ID -3143229)