REPAIR/MAINT OF BOUNDARY WALL, BARBED WIRE FENCING, PLASTER, BRICK WORKS, GATES ETC AT BASE HOSP AND REPAIR/MAINT TO STP PLANTS AT VARIOUS LOCATIONS UNDER GE E/M LUCKNOW

Amount

Demolition of cement concrete (un-reinforced) of any description and any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete in of any description and in any position not otherwise provided for complete all as specified and directed.

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed.

Brickwork with Fly ash bricks (bricks shall be burnt clay flyash building bricks as per IS- 13757), straight or curved on plan exceeding 6.0 m mean radius built in cement sand mortar 1:6 ,complete all as specified and as directed.

Plain cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping,padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work ,complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls by brooming down and priming plastered and other surfaces with and applying two coats of cement base paint over a coat of alkali resistant priming paint (before application of cement base paint) ,complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep & getting out in soft/loose soil including removal of surplus spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 meter above the starting point, complete all as specified and directed.

Plain cement concrete (1:4:8), type D-2, using 40 mm graded mechanically crushed stone aggregates as in sub base 100 mm thick with finishing the surface even and rough, complete all as specified and directed.

60 mm thick PCC intrelocking tiles (rubber laminated finish ) of size and shape as approved , laid dry on sand not less than 20 mm thick, interstices filled in floors/ pathway complete all as specified and directed.(Note :- Sand cushion shall not be measured and paid seperately)

Plain Cement Concrete 1:2:4 ,type B1 ,using 20 mm graded mechanically crushed stone aggregates as in roof kerb, mud stops, channel/ benching of manhole laid to shape and slope surface finished even and smooth using extra cement including necessary formwork rounded or chamfered on edges , complete all as specified and directed.

18-20 mm thick polished granite stone slab ( Black colour) , bedded over screed bed and jointed in cement mortar to match the colour of slab as in flooring, complete all as specified and directed. (Note:- Screeding bed shall be measured and paid separately)

Preparing new steel surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer , complete all as specified and directed.

Rendering 15mm thick on brick wall or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Complete removal existing treatment incl preparing unplastered old surfaced and distempering walls with two coats of cement base paint white or tinted over and including a coat primer on wall sufaces including 2mm thick layer of wall care putty complete all as specified and directed.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed.

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

Providing RCC (Nominal mix ) type B-1 1:2:4 ( 20mm graded agg ) as in slabs supported on walls beams and columns in floors, roofs, landings balconies canopies deck slab and in shelves and the like complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, n.exc 200mm thick fair finished concrete surface complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over as in reinforcement cut to length , bent to shape required, including cranking, bending spirally for hooping ends for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.90 mm dia, complete all as specified and directed.

15mm thick screed bed in cement mortar 1:4 with complete all as specified and directed.

Dismantling structural steel work including doors, windows & gates but excluding framed trusses etc complete all as specified and directed.

Rolled Mild steel in joist, channel,angle, or tee sections , fixed independently , without conecting plates, etc. ( cut to ordinary lenghts i.e. with in 20 mm of the length indicated) Fe-410-w(gde-E-250 quality A) complete all as specified and directed.

Preparing new steel surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer , complete all as specified and directed.

18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, polishing and rubbing complete all as specified and directed.

18-20mm thick machine cut Kota stone slab as in skirting /riser over cement mortar rendering 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, polishing and rubbing complete all as specified and directed.

Dismantling post or struts (wood/steel or rcc) any section incl taking out embedded portion and making good distrubed on normal ground in concrete, brick works masonary complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum getting out returing filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and directed.

Plain Cement Concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) in any thickness size and shape including pilasters, buttress, column, pillar, post (including caps and bases etc , complete all as specified and directed.

Mild steel work as in angle iron fencing posts, struts including cutting, tops to shape as directed bent to shape, drilling holes, notching for wire etc including all necessary bolting or riveting etc and embedding on concrete complete all as specified and directed.

Mild steel flat iron supports for posts/struts for securing fencing (chain link) using MS rods including drilling holes, notching for wire etc complete all as specified and directed.

Mild steel bolt 10 mm dia of shank factory made with hexagonal or square heads at one end and screw the other to be fitted with washer etc Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long , complete all as specified and as directed. Note-Length of ordinary bolts shall be measured from the underside of the head to the end of shank)

Fixing only chain link galvanised wire fencing mesh size or with 3 mm nominal dia and both ends without knuckling/ twisting, fixed to flat iron rails with RCC/Angle iron post , complete all as specified and directed. Note:- Supply of chain link and mild steel galvanised line wire shall be measured and paid separately under respective item of this schedule .

Supply only chain link MS galvanised fencing of size 100x100x3 mm , complete all as specified and as directed.

Supply only 4mm dia plain mild steel wire, galvanised class 3 , in fencing including straining and fixing to steel posts and/or to straining bolts as directed. (each line of wire to be measured) ,complete all as specified and directed.

Dismantling fencing wire mesh any type , complete all as specified and directed.

Material and Labour for taking out /dismantling of Air blower pump set of rating 3 phase 440 Volts supply of capacity upto 12.5 HP from STP plant at any location for repair and re-installation/refixing the same after repair at its original site and testing complete all as specified and directed. (Note : Defective parts, rewinding etc shall be measured and paid separately under respective item)

(a) Cutting out the existing winding of the motor,strip opening of winding, re-winding of motor with same size and gauge of super enamelled copper winding including tapping, varnishing, with the insulating sleeve and making connection complete all as specified and directed.

(b) Repairing of pump by re-threading of worn out studs holes and supply and fixing over size studs with nut and washer complete all as specified and dierected.

(c) Repairing of pump shaft by remetal on it by breazing, grinding and polishing make it of appropriate size of the shaft complete all as specified and directed.

(d) Supply only gun metal/stainless steel bush of pump shaft complete all as specified and directed.

(e) Supply only driven end bearing of blower shaft complete all as specified and directed.

(f) Supply only non driven end bearing of blower shaft complete all as specified and directed.

(g) Supply only gland packing complete all as specified and directed.

(h) Supply only coupling with studs between motor & air blower complete all as speicifed and directed.

(j) Supply only suction air filter complete all as specified and directed.

(k) Supply only of suction silencer complete all as specified and directed.

(l) Supply only Neck ring impeller complete all as specified and directed.

(m) Supply only bearing of motor shaft complete all as specified and directed.

(n) Supply only V belt for blower motor as existing size complete all as specified and directed.

All as per item No 39 here in before but for capacity of 7.5 HP

(a) All as per item No 40(a) here in before but for capacity of 7.5 HP

Attend the day to day complaint of non functing part to Air Blower , Air Blower Motor ,non clog submersible Pump, motor and all connected parts complete all as specified and directed. ( Note : - (i) Spare Parts shall be measured and paid separately under appropriate items. (ii) Complaint Should be attend immediately within two hrs & Rectified the same day at the earliest without effecting of service. (iii) Failing which recovery @ Rs. 200.00 per day per complaint shall be made if the complaint rectified after 24 hrs (iv) All complaint duly signed by the EIC and contractor shall be part of the RAR & Final Bill.)

Attend the day to day sewage complaint related leakege , choke , replacement of any part , with cutting ,jointing and any other work of GI Pipe ,MS Pipe , PVC Pipe for any size ,type ,capacity and any location rectified the same complete all as specified and directed. ( Note : - (i) Spare Parts shall be measured and paid separately under appropriate items. (ii) Complaint Should be attend immediately within two hrs & Rectified the same day at the earliest without effecting of service. (iii) Failing which recovery @ Rs. 200.00 per day per complaint shall be made if the complaint rectified after 24 hrs. (iv) All complaint duly signed by the EIC and contractor shall be part of the RAR & Final Bill.)

Attend the day to day Electric complaint related to ,MCB DB ,Panel Board , DG set ,Electric cable ,Switch socket & other Electrir connected of any size ,type ,capacity and any location rectified the same complete all as specified and directed. ( Note : - (i) Spare Parts shall be measured and paid separately under appropriate items. (ii) Complaint Should be attend immediately within two hrs & Rectified the same day at the earliest without effecting of service. (iii) Failing which recovery @ Rs. 200.00 per day per complaint shall be made if the complaint rectified after 24 hrs. (iv) All complaint duly signed by the EIC and contractor shall be part of the RAR & Final Bill.)

Material and labour for taking out the silt & foreign object , mechanically cleaning & Removing sludge from course bar screen including all chamber of equilasation tank upto depth of 15 Mtr any capacity STP complete all as specified and directed.

Material and labour for taking out the silt & foreign object , mechanically cleaning & Removing sludge from Fine bar screen ,Oil & Grease Chamber with water pressure, bleaching powder etc complete all as specified and directed.

Material and labour for taking out the silt & foreign object ,mechanically cleaning & Removing sludge from MBBR I & II Chamber with water pressure, bleaching powder etc complete all as specified and directed.

Material and labour for taking out the silt & foreign object ,mechanically cleaning & Removing sludge from Tube Setteler Chamber with water pressure, bleaching powder etc complete all as specified and directed.

Supply and fix in replacement Plastic Media MBBR (Media) as per existing size & specification of IS complete all as specified and directed.

Supply and fix in replacement of bubble diffuser as per existing specified size complete all as specified and directed.

Supply and fix in replacement Pac media in tube settler tank as per existing specified size complete all as specified and directed.

Replacement of sand filter media of sludge drying bed as per specification laid specification of IS complete all as specified and directed.

M & L for replacement of MS gate of sludge drying bed as per existing size thickness and specification complete all as specified and directed.

M & L for painting of old M S pipe of size 200 mm,150mm,100mm, 80mm , 65mm,50mm, 40mm,25mm,20mm, and angles grame of size 200mmx100mmx20mm for complete one STP and applying two coats of epoxy paint with one coat of primer complete all as specified and directed.

Supply and fixing in repairs pressure guage analog type suitable for pressure range 0 to 10 Kg/Cm2 complete all as specified and directed.

Material and Labour for taking out unserviceable/burnt raw submersible pump set lifting from 54 fit depth of capacity upto 10 HP of rating 3 phase 440 Volts supply from raw sewage collection sump of STP plant at any location and repair from authorised workshop for repair and re-installation/Re-fixing/lowering in the sewage sump complete all as specified and directed. Note :-(i) Spare Parts shall be measured and paid separately under appropriate items) listed here below :-

(a) Cutting out the existing winding of stator of submersible motor ov capacity 10 HP of any make and rewinding with water proof copper winding wire of appropriate guage as existing complete all as specified and directed.

(b) Straightening of the slots of stator of submersible motor of any make.

(c) Supply only thrust bearing block complete of submersible pump of any make.

(d) Supply only gun metal bushes for submersible motor as per manufacturer's design and specification.

(e) Supply only sand guard of submersible motor.

(f) Supply only of bronze metal impellars

(g) Supply only of shaft sleeve

(h) Supply only of set of gasket and O-ring

(j) Supply only of Mechanical seal motor end.

(k) Supply only of Mechanical seal pump end

(l) Supply only deep groove ball bearing motor side

(m) Supply only groove ball bearing pump side

(n) Supply only pump casing

(o) Supply only of intermediate casing

(p) Supply only of bearing housing

(q) Supply only of bearing cover

(r) Supply only of shaft protection sleeve

(s) Supply only of bowl, cast iron

(t) Supply only of bearing sleeve complete

(u) Supply only of rotor

All as per item No 69 here in before but for capacity of 5.5 HP

(a) All as per item No 70(a) here in before but for capacity of 5.5 HP

All as per item No 69 here in before but for capacity of 2.0 HP

(a) All as per item No 70(a) here in before but for capacity of 2.0 HP

Supply & filling of new Gear Oil Grade G-90 for Air Blower complete all as specified and directed. Make- Castrol/HP/Valvoline

Supplying, laying or fixing, jointing and testing LT underground electric power XLPE cable 10 Sqmm 2 Core, crossed linked polyethylene (XLPE cable) insulated, two or more core, galvanised steel strip or wire armoured, ISI-7098 Marked with aluminium conductor multistranded, heavy duty 1100 volts grade including taking out of old exisiting and laid in trenches/laid under floor or fixed naked with walls/on poles/in ducts/ in GI pipes etc complete all as specified and directed. (Note : Excavation, earth work, sand cushioning, protection bricks/ tiles/block, clamps, nuts, bolts, washers and pipe shall be measured and paid separately under appropriate items)

All as per item No 96 above but 70 Sqmm 3.5 Core

Supply & Fixing Flat type submersible cable PVC insulated and PVC sheathed copper conductor 10 Sqmm 3 core 1100 Volts grade, flat cable conforming to IS-694:1977 complete with necessary electric connection complete all as specified and directed.

Supply & Fixing Flat type submersible cable PVC insulated and PVC sheathed copper conductor 6 Sqmm 3 core 1100 Volts grade, flat cable conforming to IS-694:1977 complete with necessary electric connection complete all as specified and directed.

Supply and fixing in repairs bi-metallic overload relay with single phasing protection of range 2.5 to 4 Amps of make - Siemens or any other specified make complete all as specified and directed.

Supply and fixing in repairs power contactor ML-3, 3 Phase, 415 Volts current carrying capacity 4 to 25 Amps, coil voltage 220 volts, 50 Hz of existing make complete all as specified and directed.

Supply & Fixing in repairs MCB TPN 32 Amps, 440V AC 'C' series ISI Marked, complete all as specified and directed.

Supply and fix in repairs Single Phase preventor to prevent single phasing , reverse phasing wiring & testing complete all as specified and directed .

S&F MCCB 4 Pole, current rating 100 Amps, thermal & magnetic setting adjustable 70%-100% breaking capacity 10kA at 415V,50Hz, complete all as specified and directed.

S&F MCCB 4 Pole, current rating 160 Amps, thermal & magnetic setting adjustable 70%-100% breaking capacity 16kA at 415V,50Hz, complete all as specified and directed.

Supply, laying, jointing, testing and commissioning in replacement of Mild Steel pipes Medium grade in any length, conforming to IS:1239(I) with flanged ends with and including all fittings and fixing on wall/floors /trenches including painting with two coats of synthetic enamel paint of existing tint/colour for the 25 mm dia sizes including taking out of u/s pipe complete all as specified and directed

(b) 40 mm dia

(c) 50 mm dia

(d) 65 mm dia

(e) 80 mm dia

(f) 100 mm dia

(g) 150 mm dia

(h) 200 mm dia

Supplying and laying in replacement of CPVC pipe of 100 mm dia of sehedule 80 pipes & plain CPVC sehdule 80 with and including all fittings laid in trenches, wall etc , complete all as specified and directed

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide and getting out in Soft/Loose soil for laying of pipes/LT cables complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in Soft/Loose soil complete all as specified and directed.

Removing surplus excavated material in soils not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply and spread sand for cushioning to UG cable including spreading leveling and hand punning etc complete all as specified in clause 19.75 of SSR Part-I.

M & L Sub class ‘B’ brick laid dry flat complete all as specified and directed

Supply and fixing in repairs cast iron butterfly valve (wafer type) lever operated class PN-1.0, S.S-304 Disc, Nitrile/EPDM rubber lining including making new flanged joint with 3mm thick rubber gasket (Packing ring) with necessary bolt, nuts and washer of suitable size complete all as specified and directed of 50 mm dia size.

(b) 65 mm dia

(c) 80 mm dia

(d) 100 mm dia

(e) 150 mm dia

Supply and fix in replacement of 15 mm dia bronze ball valve screwed type complete all as specified and directed

Supply and fix in replacement of 20 mm dia bronze ball valve screwed type complete all as specified and directed

Supply and fix in replacement of 25 mm dia bronze ball valve screwed type complete all as specified and directed

Supply and fix in replaceemnt of Non return valve 100 mm dia PN 1.0(flanged) swing type with natural Rubber flap flanges as IS 5312:1984, inculding taking out of old NRV, complete all as specified and directed

S&F mild steel tubes of size 15 mm bore (medium grade) galvanised with all fittings and laid in trenches, under floors or roads incluing taking out existing tubing etc, Including taking down of eixsiting old pipe fitting complete all as specified and directed

General servicing of Kirloskar Make DG set including tappet adjuistment of 82.5 KVA sets including supply and replacement of tappet cover gasket complete all as specified and directed. Note :-(i) Spare Parts shall be measured and paid separately under appropriate items listed here below :-

(a) Supply only of diesel filter Primery and secondary .

(b) -do- but Lub Oil filter

( c) -do- but radiator hose pipe Set

(d) -do- but Fan belt

(e) -do- but fuel/lub oil pipe flexible.

(f) - do - but Lub oil filter cartridge

(g) -do- but Air cleaner Element

(h) -do- but Hose pipe for Air cleaner

(j) -do - but Hose thermostat by pass

(k) -do- but Hose water pump to radiator

(l) -do- but Hose water pump inlet to radiator

(m) -do- but Hose make up tank

General servicing of Kirloskar Make DG set including tappet adjuistment of 30/50 KVA sets including supply and replacement of tappet cover gasket complete all as specified and directed. Note :-(i) Spare Parts shall be measured and paid separately under appropriate items) listed here below :-

(a) Supply and replacement of diesel filter ( 34.32 -1200) Primery and secondary .

(b) -do- but Lub Oil filter

( c) -do- but radiator hose pipe Set

(d) -do- but Fan belt

(e) -do- but fuel/lub oil pipe flexible

(f) - do - but Lub oil filter cartridge

(g) -do- but Air cleaner Element

(h) -do- but Hose pipe for Air cleaner

(j) -do - but Hose thermostat by pass

(k) -do- but Hose water pump to radiator

(l) -do- but Hose water pump inlet to radiator

(m) -do- but Hose make up tank

Disconnecting of oil chamber of any capacity og DG set and decaning of old lub oil from all sets . Supply and filling the new oil 20W/40W all as per manufacturer's recommendation up to required level complete all as specified and directed

Dismantling the booster coil from alternator of DG set of capacity 82.5 KVA installed at STPs and transporting to civil workshop for repair. strip opening of alternator, taking out burnt copper winding, cleaning the slouts of stator and cleaning the rotor, rewinding the stator field coil with supper enameled copper winding wire of existing size and gauge including provision of new insulating material of class 'E', insullation varnishing, heating etc reassembling the same, bringing back to its original location, connecting and testing complete all as specified and directed.

Taking out Fuel injection pump assembly from DG set 82.5 KVA capacity and overhauling /calibration of the same from authorised dealer /calibration agency including replacement of worn out part such as gasket set, drive shaft, techno meter pump kit, bearing weight carrier, O ring sims etc for re- fixing pump assembly to DG set at site complete all as specified and directed.

Dismantling of Dynamo from DG set of capacity 30/50 KVA installed at STPs and transporting to workshop , strip opening taking out burnt winding wire form the stator cleaning the slot and re-winding the same with suitable size of copper winding wire , replacement of worn out diod, bearing and cutout , overhauling & servicing of the Dynamo and tranporting back to site and connecting the same with DG set and testing complete all as specified and directed.

Supply and fixing (in repairs ) sealed battery maintenance free, 12V 180 AH including initial charging complete all as specified and directed. Make- Exide/Amron/Luminous

S&F crocodile clip for connecting to battery terminals complete all as specified and directed.

Material and labour for spray painting of DG Set of capacity 82.5 KVA after prepartion of surfaces apply two coat of synthetic enamelled paint with and including marking of SM/MES No. of existing size complete all as specified and directed.

Material and labour for spray painting of DG Set of capacity 30/50 KVA after prepartion of surfaces apply two coat of synthetic enamelled paint with and including marking of SM/MES No. of existing size complete all as specified and directed.

Supply of liquid clorine sodium hypochlorite ( Grade - I ) with 9 % clorine contents by volume confirming to IS-11673 in sealed non chemicale re-actined / oxidation LDPE Container of 40 Kg PVC tank with manufacture clorine test certificate and manufacture date mark not more than 02 week ago as required on monthly basis complete all as specified and directed . Make :- M/S Grasim Industris Ltd ( chemical division ) New delhi, Purichor as approved by GE .Note : - (i)The Contractor shall arrange for independent testing for clorine contents from any Govt analysist / CHCC lab / Lan Nigam at own cost and shall be produced along with their claim for Payment . (ii) Empty container shall be property of the contractor.

S&F in replacement of junction box made out of steel of size 300x300x150mm complete with 100 Amp 3 phase & one netural rated aluminium bus bar with MS clamp of size 35x6mm MCB single 6 Amps inside box and fixed on pole with MS clamps, nut bolt and washers complete all as specified and directed

S&F in replacement of junction box made out of steel of size 300x300x150mm complete with 100 Amp 3 phase & one netural rated aluminium bus bar with MS clamp of size 35x6mm and MCB TPN 32 Amps inside box and fixed on existing location with MS clamps, nut bolt and washers complete all as specified and directed

Supply and fixing in replacement of LED street light fitting 50 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermalmanagement in multiple optics complete withIP 65/66 protection complete. incuding taking down of old light fitting, complete all as specified and directed. Make- Philips/Crompton/Havells/Bajaj/Wipro

Bailing out mud/sludge from 40 fit of sewage tank mechanically and disposing off the sludge outside MD land including cleaning of sludge tank complete all as specified and directed.

M/S S&R Construction