Tender/2020/Painting Girls Hostel/02

Amount

Civil Work items 1 to 24 Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing HSR 8.5 (b) In cement

Dismantling reinforced cement concrete with cleaning and straghtening and cutting of bars if required. Terrace leval 4th storey HSR 8.6 (e) + note (ii) )(a) +3

Removing doors and windows (wooden and steel) together with the Dismantling of walls:- HSR 8.17 (b) windows

Scraping white wash and colour wash (HSR 8.32 (a)

11.43 cm thick brick wall with every fourth course reinforced with hoop-iron laid in 1:4 cement stone dust (from crusher) mortar in superstructure. HSR 11.51+ Note (iv) (b)+3

Scraping Cement plaster. HSR 8.32 (c)

11.43 cm thick brick wall with every fourth course reinforced with hoop-iron laid in 1:4 cement stone dust (from crusher) mortar in superstructure. (HSR 11.51)

Providing & fixing PVC Rain water pipe 6 kg. Pressure of ISI mark in cement mortar during masonry work. HSR 13.89 (b) 150 MM dia PVC pipe 6 Kg. Pressure.

12 mm thick cement plaster 1:5 (HSR 15.6)

1st Floor (HSR 15.6 + Note (i)

2nd Floor (HSR 15.6 + Note (i)+2

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Whitewashing Two coats (HSR 16.47)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work. (HSR 16.57)

Providing two coats of exterior acrylic emulsion paint. HSR 16.79 (b) 1st. Quality

Providing and applying two coats of white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete (J.K/ Birla make). (HSR 16.81)

Factory- manufactured paneled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than tak, conforming ot I.S. specification no. 1003, kiln-seassoned), with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail and 100 mmm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in positon (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in positon)- HSR 17.90 (a) 35 mm thick - 17.18 note (i)

Factory-manufactured wire gauze door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc, (non coniferous timber other teak, conforming to I.S. specification no. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide locak rail 200 mm wide bottom rail and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fitting other than specified above, but including labour for fixing the same in position)- (styles and rails of windows shutter shall be 75 mm wide) HSR 17.92 (i) 30 mm thick - note (i) below 17.18(i)

Factory manufactured solid flush door Shutters (Century /Duro), with block board core as per I.S. No. 1659-1969 bonded with water poof type phenol formal dehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in positon includeing iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- The shutters is to be warranted for a period of 5 year for any type of manufacturing defects / failure. HSR 17.93 (a) commercial veneering with vertical grains or corss bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (ii) 30 mm thick

(iii) 35 mm thick

Supplying and fixing glass panes including special metal sash putty of approved make HSR 18.30 (b) glass panes 4 mm thick, exceeding 40 sq dm areas.

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified sections, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, or approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete:- HSR 18.34 (c) door and window frame size 127 mm X 50 mm with 40 mm wide double rebate

Providing & fixing 19mm thick commercial board (Duro/Century) shelves including anti termite treatment applying priming coat with wood primer and applying enamel paint work, complete in all respects. (N.S.)

Public Health Work Items 25 to 46 PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) INDIAN TYPE WATER CLOSET SUITE CONSISTING OF:- (i) Closet set VITREOUSCHINAWARA W.C. PAN WITH FOOTRESTS, 100 MMH.C.I. ‘P’ TRAP WITH or without vent as required and suitable joint for closet inlet; (ii) 12 ½ LITRES CAPACITY mosquito proof CAST IRON FLUSHING CISTERN BEST INDIAN MAKE I.S.I. MARKED NOMOS OR OTHER (as approved by the Engineer-in-charge) painted with non-yellowing white or other approved shade ENAMEL PAINT ON OUT SIDE AND BLACK BITUMASTIC SUPERIOR PAINT OR APPROVED manufacture ON INSIDE complete with all accessories such as 20 mm G.I over flow pipe with specials & clamps upto 15 cm above floor level of W.C. room, and brass perforated mosquito proof cap, 32 mm outlet, 15 mm I.S.I marked ballcock, G.I pull and chain, R.S. or C.I painted brackets and mosquito proof couplings for outlet and overflow pipes, etc. (iii) Galvanized inside and outside STEEL FLUSH PIPE With clips;Complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS AND PAINTING OF FITTINGS,ETC. HSR 30.1 (a) Size 580 mm (i) White

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUITE, SYPHONIC TYPE, Consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge) (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. HSR 30.5 (a) Single trap symphonic W.C. Suite (i) White

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid. HSR 30.13 (i) White plastic seat (Solid)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D INLET. HSR 30.66 (c) C.P brass with revolving joint.

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. HSR 30.68 (e) C.P brass towel ring.

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the wells etcs. HSR 30.70 (a) C.P BRASS (i) Soap dish large

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRRON Mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. HSR 30.71 (a) INDIAN MAKE (i) 600 mm x 450 mm

Providing and fixing in position 15 mm i/d C.P brass bib Cocks of best quality (as required by Engineer-in-charge) HSR 30.75 (a) Bib cock long body

(c) Bib cock

Providing and fixing in position C.P brass stop cocks (as Approved by the Engineer-in-charge) HSR 30.76 (a) 15 MM STOP COCK (ii) Concealed stop cock with flange.

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P BRASS INLET CONNECTION 15 MM WITH 375 MM PIPE AND C.P BRASS NUTS. (HSR 30.83)

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASSBALL VALVES IN TANKS. HSR 30.110 (b) WITH PLASTIC BALL (ii) 20 mm internal diameter

(iii) 25 mm internal diameter

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (Except civil work). HSR 30.119 1000 ltr. capacity

2000 ltr. Capacity

Providing and fixing in position CP jet connections for EWC complete including CP plate for jet and PVC connection for jet point complete in all respects.

Providing and fixing PVC flush tank 10 ltrs. capacity with all accessories compolete in all respcets. (N.S.)

Providing & fixing waste pipe 1 1/4 complete fixed in position with 32mm CP jali, complete in all respect (N.S.)

Providing & fixing disk spindle bib cock long and bib cock make ESS ESS with removal of old spindle. Complete in all respects.

Providing & fixing peet valve Zoloto & Bajaj also including removal of old peet valve. Complete in all respects. (N.S.) (i) 20mm

Providing & fixing consiled spindle including remoal of old spendle. Complete in all respects.

Electrical Work items 47 to 71 MCCB HSR (31.12) (c ) S/E of MCCB on wall or on existing pedestal including bonding to earth and necessary connections with enclosure (i) 15amp. To 60 amp. 415 V 10 K.A. 3 phase

HSR (31.12) (c ) (iv) 300amp. To 400amp. 415V 35K.A. 3 phase

HSR (31.17) (a) Miniature Circuit Breakers of 9 K.A. breaking capacity Supply and erection of miniature circuit breaker/isolator 240/415V in the existing distribution board including making necessary connections:- (ii) 6 amp. To 32 amp. (S.P.)

HSR (31.18) (xi) Bakelite angle/straight button holder Large size

HSR (31.18) (xii) Switch 5 amp on existing sheet.

HSR (31.18) (xiii) Wall socket 5 amp on existing sheet.

HSR (31.18) ( xiv) 15 amp. Switch on existing sheet.

HSR (31.18) (xv) 3 pin 15 amp. Ordinary socket on existing sheet.

HSR (31.18) (xvii) Ceiling rose flush/surface type.

HSR (31.18) (xviii) Bakelite sheet including fixing with brass screws and washers (a) 5 mm thick

HSR 31.36 (VIII) 3-Pin 15 amp. Plug point with 4 sqmm PVC insulated copper conductor cable including earthing the 3rd pin etc. (c ) Long point

HSR (31.38) Wiring only in 1.5 sqmm PVC insulated copper conductor cable in exiting conduit pipe and MS boxes covered with 5mm thick bakelite sheet including cost of switch,wall socket ,ceiling rose etc (I) Fan Point (c ) Long point

HSR (31.38) (II) Light Point (a) short point

HSR (31.38) (b) Medium point

HSR (31.38) (c ) Long point

HSR (31.38) (VIII) 3-Pin 15 amp. Plug point with 4 sqmm PVC insulated copper conductor cable including earthing the 3rd pin etc. (c ) Long point

HSR (31.40) Supply and erection of PVC unsheathed copper conductor cable single core 1100 vgolts grade in pipe of suitable size excluding cost and erection of pipe (i) Cable size 1.5 sqmm

HSR (31.40) (iii) Cable size 4 sq mm

HSR (31.41) Supply and erection of double door sheet steel enclosure distribution boards suitable for MCB's and ELCBs etc. recessed in wall including bonding to earth with all labour & material required to complete the job in all respects up to entire satisfaction of engineer-in-charge of the work (v) 4 way TP & N (Horizontal) (8+12)

HSR (31.44) Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall /ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-charge of work (b) 25mm dia

HSR (31.49) S/E of MS box made of 16 Gauge MS sheet rcessed in wall ,with arrangement of fixing brass screws , 2 Nos. check nuts and one No. PVC bush of required size including all labour and material required to complete the job in all respect up to entire satisfaction of Engineer -in -Charge of work (i) With 2 coats primer

HSR (31.55) Supply and erection of Socket size rotary step type Electronic regulator for A.C. ceiling fan Anchor make Deluxe model No. 50440 ISI/SSK Make PC 561 operated on 120/280 V.A.C. supply complete including cutting of existing bakelite sheet and making ncessary connection etc. upto the entire satisfaction of the Engineer-in-Charge of the work

N.S.:- S/E/I/T/C of following sizes of heavy duty exhaust fan suitable for single phase 230 volts, 50 Hz AC supply complete with motor, capacitor, louvers / shutters , and required size ply sheet etc. complete as required. Make- Orient / Crompton/ Bajaj 380mm dia 1400 RPM exhaust fan (15")

N.S:- Supply, installation, testing and commissioning of LED street light 90 Watt inclding the cost of one no. 6amp. MCB SP housing poly carbonate enclosure IP 65 protection with all labour & material required to complete the job , Make-Havells, Philips, Bajaj with MS pipe suitable size 6 kg weight

N.S:- S/E of following sizes of energgy saving type ceiling fan complete with double ball bearing. motor, blades, downrod, canopy, capacitor, etc. suitable for operation on 230 volts 50 Hz 50W A.C. supply complete as required. Make Bajaj (Excel), Orient (Smart saver 50), Havells sIZE 1200MM with 1.5 /2 feet fan rod

SATPURA CONSTRUCTION COMPANY