Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹16.0 CrAccepted-AOC PARAPATTY POST MALLUR VIA SALEM 636 203 | SALEM | TAMIL NADU | 636203 | ₹16.0 Cr Quoted ₹16.7 Cr | L1 | Accepted-AOC Tender Quoted Lower Amount |
| 2 | L2₹17.2 CrRejected-AOC | ₹17.2 Cr | L2 | Rejected-AOC Tender Quoted Higher Amount |
Tender Value
₹16.1 Cr
EMD Value
₹8.2 L
Closing Date
11 Aug 2023, 3:00 pmClosed
Joint Commissioner/Executive officer
Arulmigu Subramaniyaswamy temple at Tiruchendur
Providing Additional amenities to the Yatrinivas buildings construction in the premise of Arulmigu Subramanyaswamy Tirukkoil Tiruchendur, Thoothukudi Dist.
2023_HRCE_350834_1
1374/2020/A3
Open Tender
Civil Works - Buildings
184 days
Tiruchendur
Please refer Tender documents.
16 documents required · 16 mandatory
₹0
₹8.2 L
Yes
6 Oct 2023
27 Jul 2023
11 Aug 2023
27 Jul 2023
11 Aug 2023
27 Jul 2023
Amount
Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.
Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.
Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification
Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)
Providing and laying in position, standardised concrete Mix M30 grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement content of 400 Kg/m3 and maximum water cement ratio of 0.50 including admixyure (Plasticiser / super plasticiser ) in recommended proportions as per : 9103 to accelerate retard setting of concrete, improve workability without impairing strength and durability with about (5Cum) 7730kg. og 0mm machine crushed stone jelly and with about (4.3cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly with about 4.79Cu.m. )7670kg. of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying , vabricating with mechical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slab where ever necessary without claiming extra ,etc., complete.complying with standard specification and as directed by departmental officers.The coarse and fine aggregates to be used should compling with the requirements of IS Standards. ( No separete payment will be made by the department for excess usage of materials) In Foundation & Basement
Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)
Supplying and filling with GRAVEL including cost and conveyance of gravel and all labour charges for filling ramming etc.,complete with standard specifications.
Brick work using country bricks of size 8 3/4" x 4 1/4" x 2 3/4 " in Cement Mortar 1:6 (one cement and six crushed stone sand) including curing, neat finishing, etc, complete complying with standard specification.
In ground floor
Plastering with Cement Mortar 1:5 (One cement and Five p-sand), 12 mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.
Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer M-0658
Painting the wall two coats with approved water based emulsion paint paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.
painting one coat over the existing surface of wall with water based exterior emulsion paint over the plaster surface etc complete complying with standard specification
Prepare the surface and providing Ornamental finishing and Stapathy work on the Parapet wall with providing Kalasam work making in brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.300 x 750
Prepare the surface and providing Ornamental finishing and Stapathy work for provding kodungai work alround the roof slab for making arched shape to all corners with brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
terrace floor level Detail A in cottage
Centre portion
First floor level
Prepare the surface and providing Ornamental finishing and Stapathy work alround the bottom of round pillar named as peedam or pillar base brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work alround the Top of round pillar head named as peedam or pillar base brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing ornamental finishing and Stapathy allaround the window using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornrnmental finishing and Stapathy work in the half round pillar using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work side cornice using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work side cornice using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work Dhadi kondan vellai using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work Side Dhadi kondan vellai using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Pillar Projection Work ( F.F ) using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Window portion bottom basement Elevation Pillar work using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Window portion bottom and top elevation Pillar projection and formation gadi work using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy work in the Corner Parapet Decorative (Kalasam) work making in brickwork in CM 1 : 2. vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
kalasam 1.00 x1.60
kalasam 0.60 x 0.90
kalasam 0.30 x0.45
Prepare the surface and providing Ornamental finishing and Stapathy Alround the bottom of Round pillar beedam using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Alround the Centre of Round pillar beedam using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Sunshade side Cornice (Eluthuga vellai) using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the debris complete. The size and finishing works shall be indicated asper drawing enclosed and as directed by the Departmental officers etc., complete complying with standard specfication.
Prepare the surface and providing Ornamental finishing and Stapathy Sunshade side Cornice (Eluthuga vellai) using brickwork in CM 1 : 2 vargapoochu over the corewalls of vimanams/ gopurams, with CM 1:2 complete including shaping the mukhapatharam, mahanasi ,koodu all ornamental works to proper shape, by embedding brokrn bricks or shaped/ chiselled bricks ,rough -plasteringwith CM1:2 and finishing with final ornamental plastering and nayam theeevai including cost and conveyance of all materials labour therefore, lifting of matrials, all working in heights, curing with water etc, complete including all extra for folding and including clearing the
Hotel & Dormitory Building 0.67 m parapet cornice
Hotel & Dormitory Building 0.28 m parapet cornice
Hotel & Dormitory Building 0.08 m portico cornice
Hotel & Dormitory Building 0.02 m portico cornice
Hotel & Dormitory Building 0.17 m portico parapet cornice
Hotel & Dormitory Building 0.05 m Base,Roof level cornice
Hotel & Dormitory Building 0.04 basement cornice
Restaurent Alround parapet 0.10 cornice work
Prepare the surface and providing Ornrnmental finishing and Stapathy Sunshade side Cornice Dhadi Kondan Vellai using brickwork in CM 1 : 2 and plastering the same mortar etc., The rate inclusive of cost of materials and labour charges for the above all works and etc., complete. The size and finishing works shall be indicated in the drawing A and as directed by the Departmental officers etc., complete complying with standard specfication
Supplying and placing the Table of size 0.75 x 0.75 x 0.60 m with High density high moisturised resistance board (HDHMR Board). Three sides covered with HDHMR board and Top surface of the stand is finished with HDHMR Reeper at uniform spacing to prevent non-slippery of luggages with necessary bushes provided at the bottom and placed at suitable position of approved quality and design. The cost includes cost of all materials, labour charges, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and placing of wood chair of size of 1'6"X1'6"X1'9" with following specifications 1) spindle made out of 32x20 mm with ornamental fininshing 2) The front and rear leg made out of size 40x50mm 3) Aprons made out of size 40x40mm 4) handles are madeout of 80x40mm 5) The bottom and back of the chair provided with fabric cushion arrangements 6) Decorations to improve the elevation of the Chair etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and placeing the Reception table with high density high moistureised resistance board ( hdhmr board ) . Two sides and top of the table covered with hdhmr board including drawer arrangements neceeary bushes provided at the bottom and placed at suitable position of approved quality and design . The mirrior is embedded with top of the table having size of 0.60 x 1.250 m with alround 3 " borders with hdhmr board etc ; the cost includes cost of all matrials , labour charges , loading and unloading etc; complete complying with standard speification and as directed by departmental offiers The sample shall be got approved by the Executive Engineer
Providing and fixing of Teak wood cot of king size having a dimensions of 6'3" x 6'8" x 24" with the following specifications. Teak wood side rails having a cross section of 5" x 1", Teak wood top and bottom rails at Head board and Foot board having a cross section of 3" x 2", Teak wood slat board having a cross section of 2.5" x 1", Teak wood board of height 48" and width 6"3" and 1.5" thick teak wood head board legs having a size of of 4" x 4" x 48" and foot board legs of size 4" x 4" x 24". The head board and foot board are provided with Teak wood Planks of 40mm thick. the Bed board is provided with 19mm thick plywood of water proof grade hard wood ply of best quality. All the members are connected by means of necessary joints, steel bolts and nuts. The Teak wood Cot should comply with given design, wood carving, it should be finished neatly with wood polish of two coats etc., The cost includes cost of materials, labour, loading, unloading, transportation, fitting, polishing etc., Complete complying with standard specifications.The sample shall be got approved by the Executive Engineer
Supplying and fixing of S.S. Cot of size 3' x 6'6" x 1'6" Made by 16 guage CRCA Sheet with frames made of round tubular section of size 1.25" dia of 16 guage thickness. The Steel Cot is stiffened at the bottom by three numbers of 25mm x 25mm x 3mm size SS angles in the longitudinal direction and the legs are made up of 1.25" dia MS pipe with necessary bushes. all the components of the Cot are connected by means of steel bolts and nuts. The steel cot should be as per the approved design. The cost includes cost of all materials, labour, loading, unloading, fitting, etc., Complete complying with standard specification.The sample shall be got approved by the Executive Engineer
Supplying and Fixing of Wardrobe Size of 6'6" x 4'0"x1'10" (H X B XD ) Made of Heavy grade (wp) Boards, all Doors fitted with “Soft Closer”, each side 5 no’s totally 10 no’s, Drawer fitted one no. of Lock with Key, side branded telescopic runners, Top of the wardrobe both side fitted with “SS” hanger bipes, Bottom of the Wardrobe fitted with lengthy bushes, front door fitted one heavy locker with key. And two long SS handles total wardrobe and fittings guarantee covered 3 years.,complete and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and placing King Size Mattresses of size 6'3" x 6'8" x 6" thickness of approved and best quality Multi layer spring and foam type wih the following specification. The top and bottom layer of the mattresses consist of 25mm thickness of Fabric made up of 23 D Poly Urethene(PU) foam and non woven 22 GSM with quilt. The middle layer consist of 100 mm thick, 23D multi layer panel consist of pocket coiled springs. The mattresses should comply with standard specifications and make such as kurl on / Repose / Duroflex / Peps etc. The cost includes cost of all materials, labour, loading, unloading, etc., Complete complying with standard specification.
Supplying and placing Single Cot Mattresses of size 3' x 6'6" x5" thickness of approved and best quality Multi layer spring and foam type wih the following specification. The top and bottom layer of the mattresses consist of 20mm thickness of Fabric made up of 23 D Poly Urethene(PU) foam and non woven 22 GSM with quilt. The middle layer consist of 100 mm thick, 23D multi layer panel consist of pocket coiled springs. The mattresses should comply with standard specifications and make such as kurl on / Repose / Duroflex / Peps etc. The cost includes cost of all materials, labour, loading, unloading, etc., Complete complying with standard specification.The sample shall be got approved by the Executive Engineer
Supplying and placing polyester fibre pillow of size 60cm x 40cm made up of polyester fibre filler materials and must be white in colour. The pillow should provide good support and washable. It should be of hygenic quality and must keep from allargies. The cost includes cost of pillow, loading and unloading, transportation etc., Complete Complying with Standard Specifications.The sample shall be got approved by the Executive Engineer
Supplying and placing Cotton Pillow covers of size 68 cm x 46 cm made up of high quality cotton fabric of 160 TC in white colour. The pillow cover should be ideal for pillows of size 60 cm x 40 cm. The cost includes cost of pillow cover, loading and unloading, transportation etc., Complete Complying with Standard Specifications.The sample shall be got approved by the Executive Engineer
Supplying and placing Cotton Bed Spread of size 274 x 274 cm made up of high quality cotton fabric of white colour. The cost includes cost of Bed spread, loading and unloading, transportation etc., Complete Complying with Standard Specifications.The sample shall be got approved by the Executive Engineer
Supplying and placing Cotton bath towels of size 70 cm x 140 cm made up of high quality and soft cotton fabric of white colour. The cost includes cost of towel, loading and unloading, transportation etc., Complete Complying with Standard Specifications. The sample shall be got approved by the Executive Engineer
Supplying and placing of bucket set for the bath rooms consist of the following. The buckets and mugs should be made up of virgin plastics and of durable quality.The cost includes cost of Bucket sets, loading and unloading, transportation etc., Complete Complying with Standard Specifications. The sample shall be got approved by the Executive Engineer
Bath Bucket - 25 litres capacity
Bath Mug - 1.5 litres capacity
Toilet Bucket - 5 litres capacity
Toilet Mug - 1 litre capacity
Supplying and placing of plastic dust bin of size 22.5 cm x 22.5 cm 24.50 cm made up of virgin plastic and of durable quality. The cost includes cost of dust bin, loading and unloading, transportation etc., Complete Complying with Standard Specifications. The sample shall be got approved by the Executive Engineer
Supplying and placing of Reception wood chair of size of 0.6X0.6X0.9 with following specifications 1) spindle made out of 32x20 mm with ornamental fininshing 2) The front and rear leg made out of size 40x50mm 3) Aprons made out of size 40x40mm 4) handles are madeout of 80x40mm 5) The bottom and back of the chair provided with fabric cushion arrangements 6) Decorations to improve the elevation of the Chair etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and Placing Stainless Steel 304 grade Reception waiting chair 4 seated chair for approved quality best variety etc complete complying stardard specification The sample shall be got approved by the Executive Engineer
Supplying and Placing Stainless Steel (304) grade SS TABLE WITH GRANITE ON TOP the following items in the RESTAURENT .The sample shall be got approved by the Executive Engineer
Dinning table -6'x4'x2'6"
Vip dinning table -5'x4'x2'6"
Vip dinning table -6'x4'x2'6"
Out door dinning table -4'x5'x2'6"
Service table-5'9"x2'x2'6"
Chair
Supplying and placing of Teak wood Teapoy of size 0.90 x 0.60 x 0.50 m with legs of size 2" x 2 “top of the table 12 mm glass finished with glabanished finishing, finally finished with 3 coat of melamine water proof polish finish, the cost includes cost of all materials ,labour charges ,loading and unloading etc: complete complying with standard specification and as directed by the departmental officers .The sample shall be got approved by the Executive Engineer
teapoy 3' x2' x 1'6"
Family cottage single seater sofa
Family cottage three seater sofa
Supply and Ground preparation with suitable garden sweet( Farmyard manure, Pesticides) top 0' 1''Spreading and proper levelling and grading for planting areas, earth mount formation and supervising .The sample shall be got approved by the Executive Engineer
Supply, transportation to site and Laying of mexican grass carpet, Rate to include supply of grass , labour charges for mixing, soil media in the desired proportion and laying and dibbling of rooted grass mat. Mexican grass Turffing Method .planting the sapling and maintenance for a period of 1 year from the date of completion of planting. The sample shall be got approved by the Executive Engineer
Supply, transportation to site and Planting of following plants Rate to include supply of Plant , labour charges for mixing, soil media in the desired proportion and laying Planting the sapling and maintenance for a period of 1 year from the date of completion of planting. The sample shall be got approved by the Executive Engineer
Adineum
Foxtail palms
Ficus benjamina
Raphis palms
described below.Ground covers are to be planted in planting beds which are filled to a minimum depth of 230 mm with mixing garden soil. The rate will includethe cost of sapling, labour charges for pitting, mixing soil media, filling the planting bed with soil media, planting the sapling and maintenance for a period of 1 year from the date of completion of planting. The sample shall be got approved by the Executive Engineer
Supply, transportation to site and planting of Shrubs at min. 300mm height with pits of size 300 x 300 x 300 mm. Each pit should contain a minimum of mixing garden soil . Rates to include labour charges for pitting mixing soil media, filling the pits with soil media & planting the saplings. Shrubs Varieties planting the sapling and maintenance for a period of 1 year from the date of completion of planting. .The sample shall be got approved by the Executive Engineer
Providing Lock with Key arrangements with Godrej or steelage (or) Equivalent make of 7 levers and four keys. The cost includes cost of all materials, labour charges, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Providing Brass Key Chain having size of 75mm x 40mm including name letters and room Numbers on one side (i.e., Yathiri Nivas, THIRUCHENDUR and logo on other side, All the four corners are rounded. The cost includes cost of all materials, labour charges and engraving charges, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.
Supplying and fixing of wooden Key Stand using special type and design of 19 mm thickness plywood of approved quality and design with 1mm thick colour designed mica sheet for both sides of the plywood forming key stand with vertical , Horizontal and cross planks of 40 cm width required length and height , including cost of Hook and alround lighting arrangements etc., The cost including cost of material, labours, loading, unloading, incidental charges etc., Complete complying with standard specification and as directed by the Executive Engineer.
the following features i) Cylinder Volume : 305 liters. ii) Cylinder dia : 840 mm. iii) Cylinder depth : 525 mm. iv) Drive Motor Capacity : 7.5HP. v) Heating Coil : 18 KW. vi) Net Weight 1200 Kgs. This machine is suitable for all known washes and is capable of even dyeing. The basic unit consists of a perforated high quality stainless steel drum and a steam water inlet connection without valves. Inner cylinder, outer casting, side and front panels all in stainless steel. Automatic features like auto timed, auto reverse without inverter. All machines have big glass window at the door and water flow meter, Solenoid, timer etc. This machine has a spin speed of 900 RPM with a G-force of 300 making it the first choice of any laundry managers requirements with a unique computerized system this machine is a good alternate for any imported washer extractor etc., complete as per standard specifications and as directed by the departmental officers
Supplying and fixing of Electrical Tumble Drier of size 1050 x 1320 x 1870 mm having 30 Kg capacity with the following features i) Volume : 613 liters. ii) Size of Basket Dia : 970 x 830 mm iii) Door Opening Dia : 750 mm iv) Heating coil : 24 KW v) Drive Motor Capacity 1 HP. vi) Net weight : 550 Kgs . It is made up of powder coated steel outer cabinet and stainless steel inner basket. Double walled glass insulated body. Self-cleaning lint screen with powerful blower. Auto timed, auto reverse. All electrical are of standard Siemens quality. Reputed LHP make ISO 9000 Grade motors etc., complete as per standard specifications and as directed by the departmental officers.
Supplying and fixing of Electrical Calendaring Machine of size 1600 x 400 mm. It is made up of Stainless Steel roller, Gear driven or chain driven, Variable speed, manually adjustable, powerful suction, finger guard, Built in electric control panel. With imported feeding belts. Compressed air not required for operation etc., complete as per standard specifications and as directed by the departmental officers.
Supplying and fixing of Vacuum ironing table with 2128 iron and 1.6 KW Jumbo boiler of size 130 x 80 mm. It is made up of silicon foam and heat proof cloth Totally powder coated in a state of the art conveyor powder-coating unit with trays, side iron stand with silicon iron pad. Suction motors full-length foot pedal switch to control suction. The vacuum board is uniformly perforated and covered with a stainless steel mesh for perfect and uniform steam ironing control etc., complete as per standard specifications and as directed by the departmental officers.
Supplying of Wet Trolley of size 914 x 610 x 686 mm. It is made up of Complete stainless steel construction for long rust free life. Corners should be rounded for easy movement and fitted with rubber bumpers to avoid any damage. These trolleys should be mounted with 4 nos. Swiveling type ball bearing wheels etc., complete as per standard specifications and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. 2000 Litres (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.
10 Liters
500 Liters M-0722
2000 Liters M-0724
Supply and fixing of STEAM GENERATOR outer jacket is made of 6 mm & 8 mm thick MS IS 2062 plates. Inner shell by 2 mm thick AISI 304 Grade S.S. Sheet and inner bottom plate by 4 mm AISI 304 Grade S.S. Sheet. Steam Generator is fitted with necessary accessories viz. Automatic float ball assembly, Pressure gauge meter, Water level indicator, safety valve and Drainage valve etc.The lid is made of 1.5 mm Stainless steel sheet. All outlet couplings are stainless steel. It is operated by GAS / FIREWOOD. The capacity of steam Generator is approximately 280 liters and Steam production is 0.5 kg/cm2 per hour.SIZE: M.S. Outer: 31”dia X 49” H. M.S. FIRE BAR STAND * 6” Dia MS Smoke Pipe.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supply and fixing of RICE COOKING & MULTIPURPOSE VESSEL-15KG: fabricated by 304 grade 2B finish stainless steel sheet. The vessel and the perforated plate is made of 2mm thick S.S. Sheet. The perforated plate is kept at a distance of 100 mm from the bottom plate for the effective filtration of “kanji”. 1” drainage nozzle is fitted plate with ball valve for draining the “kanji”.The vessel lid is made of 1 mm thick 304. Grade 2B finishes thickness Stainless Steel Sheet. Vessel sides are supported by 65 mm Dia S.S.Rod with steam inlet connection. Tilting handle pipe of 28 mm Dia S.S. Pipe provided with locking arrangements. It is fitted with Steam inlet 33mm dia pipe.SIZE: 19” dia X 19” H. (15KG)The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supply and fixing 03. MILK BOILING VESSEL-50 LTS: inner vessel is fabricated by 304 grade 2B finish 2mm thickness stainlesssteel sheet. The inner bottom dished portion is kept at a distance of 100 mm bottom plate for the effective functioning.The outer Vessel is made of 1.5 mm thick 304 Grade stainless steel sheet. Outer vessel bottom is made of 1.5mm thick and the vessel sides are supported by 65 mm Dia stainless steel rod with steam inlet connection. Tilting type handle of 32 mm Dia 2 mm thickness Stainless steel pipe with locking arrangements.The Vessel is made by 1 mm thick 304 grade stainless steel sheet. The Vessel is fitted with thermo dynamic steam trap valve, Safety valve, Steam inlet & outlet connected with end fittings. It is tested by Hydraulic steam pressure rating 1kg/cm2 along with Leg by 65mm SS 304 Grade Round Tube ..SIZE: 16”dia X 16” H. (50 LTS.)The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.
Supplying and fixing of 05. IDDLY COOKING PLANT-200 IDDLY plant and it is fabricated by 304 grade S.S.Sheet. The outer chamber and idly trays are made of 1.2 mm thick and the Inner chamber of 1.5 mm thick. It is fitted with all accessories viz. Automatic steam control System. This equipment has TWO independent chambers. Each chamber contains FIVE numbers of Idly trays. One tray contains 20numbers of iddlies with iddly ss stand -1nos and ghee iddly tray-2nos SIZE: 25”L. X 21”B. X 28”H. (200 NOS.) The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of STEAM PIPELINE & FITTINGS For steam generator to vessel via ¾” GI Pipe, Ball Valves, Unions, Couplings, Elbows, Tees, Asbestos Ropes / Heat resisting ropes etc., to Ensure safety and effective functioning of all Equipments. The cost includes cost of all materials, labour charges, transporatation,erection ,commissioning loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of SINGLE BURNER GAS RANGE South indian model on top Frame work by 32x3 MS L Angle, Top and four side Paneling by 1.2mm SS 304 Grade Sheet. It is fitted with Gas burner pan support, NC Valve, Copper tube, Gas inline pipe etc. Leg by 40mm SS Square tube. It is mounted on SS pipe legs.SIZE: 24”L. X 24” B.X 18” H. The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of DOUBLE BURNER GAS RANGE South indian model on top Frame work by 32x3 MS L Angle, Top and four side Paneling by 1.2mm SS 304 Grade Sheet. It is fitted with Gas burner pan support, NC Valve, Copper tube, Gas inline pipe etc. Leg by 40mm SS Square tube. It is mounted on SS pipe legs.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing odf DOSAI TAWA Made of 20 mm MS plate. Frame work by 35 X 5 mm MS ’L’ angle with paneling by SS sheet. On top 3 side paneling by SS splash guard. Legs are 40mm SS square pipe. It is fitted with necessary gas fittings ‘V’ burner, N.C. valve, copper tube, heat resisting pad, gas pipe etc.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
SIZE: 60” L. X 30” B. X 34” H
SIZE: 36” L. X 30” B. X 34” H. 1 No
Supplying and fixing of WORK TABLE (IDDLY & DOSAI) Fabricated by 1.2mm SS 304 grade sheet. It consists of top & one Undershelves. Legs are 40 mm SS round pipe with leg bush.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of BATTER TABLE ` (IDDLY& DOSAI) :Fabricated by 1.2mm SS 304 Container each capacity of 15 Ltrs and 10 Grade square tube and adjustable leg bush. grade sheet. It consist Ltrs. It is mounted on of 2 Nos. of SS 32 mm SS 304 SIZE: 30”L. X 18”B. X 34”H. The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and fixing of MASALA RACK & KITCHEN RACK Fabricated by 1.2mm SS 304 grade sheet. It consists of 4 Nos. SS racks.Legs are 40mm SS round pipe with leg bush.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing DOUBLE BURNER GAS RANGE of frame work by 35 X 5 mm MS ‘ L’ angle with paneling by SS sheet. Legs are 40mm SS square pipe with leg bush. It is fitted with necessary Gas fittings H.P.Gas burner, pilot burner, N.C.Valve, copper tube, pan support, drip tray, gas pipe etc.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of WET GRINDER in SS body with Gear Type Model & I / III. Phase motor with coconut scrapper.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
5 LTS. (1HP)
10 LTS. (1HP)
Supplying and fixing ofDOUGH KNEADING MACHINEOuter body frame work by 1 ¼” x ¼ MS ‘L’ angle and paneling by MS Sheet with powder coating. Bowl fabricated by 1.5mm SS 304 grade sheet. Arm by 65mm SS rod fitted with rectangle tube. strain.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of COMMERCIAL MIXY 5 LTS BRANDED.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of RACK IV TIER with fabricated by 1.2mm SS 304 grade sheet. It consists of 4 Nos. SS racks. Legs are 40mm SS round pipe with leg bush.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of VEGETABLE RACK (IV RACK): SS RACK with frame work by 25mm SS 304 grade square tube. Rack fabricated by3mm X 25mm X 25mm SS 304 grade weld mess. It consists of 4 racks and each rack consists of two compartments for storing of vegetables. It is mounted on 40mm SS 304 grade pipe legs.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of CLEAN PLATE TABLE - III TIER: Fabricated by 1.2mm SS Sheet. It consists of top & two under shelves.Legs are 40 mm SS round pipe with leg bush.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supplying and fixing of PLATE RACK with fabricated by 1.2mm SS 304 grade sheet. It consists of 4 Nos. SS racks. Legs are 40mm SS round pipe with leg bush.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers.The sample shall be got approved by the Executive Engineer
Supplying and fixing of SS TEA BOILER: 10 Ltrs with fabricated by 1.2mm SS 304 Grade sheet. It consist of SS milk container and water tape.The cost includes cost of all materials, labour charges, transporatation, loading and unloading etc.,complete complying with standard specification and as directed by the departmental officers. The sample shall be got approved by the Executive Engineer
Supply and fixing of stored pressure ABC (Mono Ammonium phospate) powder type Fire Extinguisher of 6 kgs capacity as per IS : 15683 with pressure guage, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance,all incidental charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc complete as per standard specifications and as directed by the departmental officers.(Make : EXCELLENT / SAFETY FIRST / EQUIVALENT as directed by the departmental officers)
Supplying and fixing of carbon dioxide Gas type 2 kg capacity Fire Extinguisher as per New IS No. 15683 complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc complete as per standard specifications and as directed by the departmental officers. (Make : OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT as directed by the departmental officers)
supplying and laying rubber mould paver block of 80 mm thick with strengh of 40kg/m2 over the sand bed including transporation charges etc complete complying standard specification and as directed by departmental officers(excluding sand cushion)
Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete complying with standard specifications M -0640 / pg -60
Design Fabrication, Supply and erection of bar screen made of MS 10mm square bars to suit the channel. Inner size of channel 1000mm , wide 900mm liquid depth and 1200mm length. The MS 10mm square bars should be properly epoxy coated to avoid the rusting of bars. The spacing between the square bar is 5mm, so that the particles above 5mm will be retained in the entry channel and will be cleared by hand rac manually. The bar screen should be kept at an inclination of 60o. The bar screen is fixed at site, inside the channel with a groove like arrangements, so that bar screen could be removed for maintenance purpose. The cost includes cost of MS bars, fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.
Design Supply and erection of Tube Settler feed pump with motor with the capacity of 2.5m3 /hr as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming coupled with base frame arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1.0 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . Motor make is Kirloskar/CRI/ Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, foundation bolts, labour charges, erection charges, transport charges etc., complete.be removed for maintenance purpose. The cost includes cost of MS bars, fabrication charges, Epoxy painting charges and fixing at site transport charges to site., etc., complete.
Design Supply and erection of Coagulant dosing pump with the capacity of of 0-6 liters per hour @ 4 kg/cm2, 0.16 HP with electronic driven construction of pump is Polypropylene . The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 100 liters with HDFE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.
Design Supply and erection of Flocculent dosing pump with the capacity of 0-6 liters per hour @ 4 kg/cm2, 0.16 HP with electronic driven construction of pump is Polypropylene . The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 100 liters in HDPE. The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.
Design Supply and erection of air blowers Ring Blower with electrical Motor, 16 m3/hr, 0.5 HP motor . Air blower with motor are provided for one number for operational and one number for standby. The Air blower make is of Raico/Equivalent to suit the design requirements. The Air blower with motor is fixed in a base frame. Necessary foundation bolts, nuts are provided to fix the total coupled assembly of Air blower and motor in the concrete bed. The cost includes the cost of Air blower, base frame , diffusers, foundation bolts, erection charges, transport charges, labour charges., etc., complete.transport charges, erection charges etc., complete.
Design, Fabrication, supply, erection of tube settler media with PVC 1000mm depth 1.1mm thickness in hexagonal chevron shaped fixed with 60 degree slope in tube settler tank 1m3 including the cost of tube settler media, erection charges , transport charges, labour charges.etc., complete
Design Supply and erection of Sand Filter feed pump with motor with the capacity of 2.5m 3 as per the design. The type of the pump is horizontal, Centrifugal, flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 2HP. The motor type suitable for 3 phase supply,440v, 50hz . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.
Design Supply and erection of Oxidant dosing pump with the capacity of 0-6 liters per hour @ 4 kg/cm2, with 0.16 HP . The material of construction of the dosing pump is polypropene. The pump is fitted Base frame necessary bolts and nut . The capacity of the tank 200 liters in HDPE . The pump is fitted with a suction and delivery line. Necessary foot valve, level indicator is provided with the pump. Including the suitable Agitator for dosing pump The cost includes the cost of the pump, tank, foot valves, delivery and suction tubes of standard length, Agitator, labour charges, transport charges, erection charges etc., complete.
Design Supply, fabrication and erection of Multi graded Sand filter unit with 530mm dia and 1570 mm height. Multi graded Sand filter is a vertical, cylindrical vessel made out of FRP The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of Multi graded sand filled over & under bed media of pebbles and gravels. The size and height of the filter media is as per the design and standards.The joints are properly vessel (Multi graded Sand Filter ) is supported by FRP legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges and painting etc., complete.
Design Fabrication, Supply and erection of Bag filter with 20 micron with 2.5 m3/hour with Polypropylene Gadridges with 5 1/2 " dia 20" length. The cost includes cost of bag filter, stand , fabrication charges, and fixing at site transport charges to site., etc., complete.
Design Supply, fabrication and erection of Eco Ozotex with Ozone Generator includes the ozone recirculation pump in 4 m3 /hour. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . ozone generator with a capacity of 50 gms / hour with oxygen concentrator, including the cost of epoxy coating for ozone reactor tank, water ozone mixing equipments with level gauge, safty valve with 1 HP motor. The cost includes the ozone generator, oxygen generator, ozone recirculation pump, motor, Stand by pump and motor for ozone recirculation pump, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.
Design Supply, fabrication and erection of Activated Carbon filter unit with 530mm dia and 1570 mm height. Activated carbon filter is a vertical, cylindrical vessel made out of FRP The inlet pipe inside the vessel is designed to have a bell mouth arrangements for liquid/water distribution, so that the filter media is in position & will not get disturbed. The bottom collection system is provided with header and lateral pipe arrangements with necessary holes. The filtered water is collected thro this header lateral pipes, will flow out to outlet pipes and vice versa. The filter media consists of Activated Carbon filled over & under bed media of Course Silex. The size and height of the filter media is as per the design and standards.The joints are properly vessel (Multi graded Sand Filter ) is supported by FRP legs, thereby fixing the vessel with foundation bolts properly in the concrete foundation bed. The cost includes the cost of materials bolts, nuts and washers, filter media, foundation bolts fabrication charges, welding charges, erection charges, transport charges and painting etc., complete.
Design Supply and erection of Back wash pump with motor with the capacity of 5.0 m3 /hr , head of 3m as per the design. The type of the pump is horizontal, Centrifugal, Non clog, self priming flexible coupling drive arrangement. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 2 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ . Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, Stand by pump and motor, base frame, Motor Guards, foundation bolts, labour charges, erection charges, transport charges etc., complete.
Design Supply and erection of Treated tank recirculation pump of capacity 10m3/hour @ as per the design. The Treated tank recirculation pump is of horizontal, centrifugal, non clog self priming type . The pump make is Kirloskar/CRI/equivalent to suit the above said flow rate and head. The pump is coupled with motor by flexible coupling drive arrangements. The purpose of the pump is to recirculation for treated tank . The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ,. The capacity of the motor is 1 HP. The motor make is Kirloskar/CRI/ Equivalent. The cost includes cost of pump, motor, base frame, Motor Guards, foundation bolts, labour charges for erection, transport charges etc., complete.
Design Supply, Fabrication and erection of piping for sewage treatment plant of capacity 50m3. The piping work consists of 1) Suction lines from Equalization tank, delivery lines to Tube settler thro' raw sewage transfer pumps. 2)Pipe lines for Blowers to Equalization tank Both MS and PVC pipes with necessary valves, pressure gauges are used as per the design and suit the flow rate. 3)Pipelines from Clarifier tank Bag filter and Multigraded sand filter 4)Pipe line from multigraded Sand filter to Ozone reactor and Ozone reactor to Activated Carbon Filter 5) Pipe line from Backwash pump to Mutigraded filter and Activated Carbon filter 6) Necessary pipe lines , valves, pressure Gauge for filters, flow meters for tube settler feed, Sand filter , Activated Carbon filter, float level switch The total piping network as given above, is within the sewage treatment units. The cost includes the cost of pipes (MS, UPVC and 1" dia to 3"dia), Specials, valves, pressure gauges, flow meters, pipe fittings, fabrication charges, labour charges, transportation charges etc, complete.
Design, Fabrication, supply, erection of electrical panel board with necessary starters, main switches, voltmeter, ammeter, and electrical cables of required sizes from pumps to panel board as per design. The size of panel board is approximately 5 feet x 3 1/2 feet, fabricated with MS sheets and powder coat. Necessary provisions are given in the panel board for bus bars, main switch , starters, switches, voltmeter ammeter as per the design to suit sewage Treatment plant motors. The cables are run from panel board to the all pumps and other electrical accessories such as level switches dosing pumps etc complete,. The cable sizes are as per the design and suitable for electrical motors fixed in the Sewage treatment Plant. No lighting points are considered. The cost includes the cost of panel board, starters, switches, voltmeter, Ammeter, main switch, cables for motors, labour charges etc., complete.
Design Supply and erection of centrifugal desludger pump with motor with the capacity of 50 m3 , as per the design. The pump make is kirloskar/CRI/equivalent, The capacity of the motor is 1 HP. The type of the motor is TEFC, IP55, CLSS-F insulation, suitable for 3 phase supply, 440V, 50HZ, 300mm Basket dia. Motor make is Kirloskar/CRI/Equivalent. Necessary base frame, foundation bolts nuts are provided to fix the coupled pump set above the foundation bed. The cost includes the pump, motor, , base frame,, foundation bolts, labour charges, erection charges, transport charges etc., complete.
Supplying and fixing iron grils for windows, ventilators and grill gates etc. as directed by the department officers etc. complete and including one coat of red oxide primer using required M.S. angles and flats in such a way that the weight per square metre is not less then 20Kgs/m2 etc., complete complying with standard specification and as directed by the departmental officers.
Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.
600 x 600 mm size depth 600 mm
Supplying and fixing in position best quality UPVC pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).
32 mm dia
50 mm dia (B.G.L)
80 mm dia (A.G.L)
100 mm dia (A.G.L)
150 mm dia (B.G.L)
Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed
50mm dia
32 mm dia
20 mm dia
50 x 40 mm dia
32x25mm dia
Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.
32mm gate valve Delivery line
65mm gate valve Delivery line
50mm gate valve Delivery line
Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.....
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). With out pedestal
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestall) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). With pedestal
Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 2500 x 900 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)
Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)
Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).
Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).
Supplying and fixing best approved best quality CP two way bib coak with Health Faucet with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (It should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position of stainless steel shower rose with stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers ( shower rose should be got approved by the Executive Engineer before use on works).
Supplying and fixing in position Wall mixture tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
Supplying and fixing position PVC Nahani Trap of the following sizes100 x 75mm with best gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)
Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation,sand filling and refilling charges etc. will be measured and paid separately in the cases where the pipe lines are proposed to laid Below Ground Level
110 mm dia
75 mm dia
Design,Supplying, fabricating and fixing in position inserts comprising edge angle, MS angles, plates, tees, flats and other structural steel sections, holding down bolts, anchor bolts, anchor plates, pipe sleeves etc., in all cement concrete works at all levels and heights above finished floor level in foundation, trenches, pits, tunnels, lift pits etc., below finished floor level including cutting, bending to shape fabricating, drilling, threading, welding lugs etc., with all tools, tackles and labour as per design or as directed including a coat of primer of approved quality and painting the exposed surface with two coats of synthetic enamel paint of approved quality and colour etc., all complete as per drawings and as directed
UPVC window specification : Supplying and fixing UPVC (un-plasticized poly vinyl chloride) window of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile size of 60x78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosive free, the profile are multi chambered section with wall thick of 2mm.The EPDM rubber (black colour) covered with all over the edges of frame and shutter.The shutter will be provided with Espag multi power point locks and also it operates as handle.The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided to the shutter and it should not allow leakages of water even at most ranging storms and should have key lockable action,security protective hinges,strong locking systems and as per size for arresting noise and energy loss .The connecting mechanism between sash and outer frame that enables opening of the window.The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The Window should be got approved by the E.E. before use on work.
Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.
Single leaf
Supply and erection of 1.5 Ton 5 star rated Split type airconditioners (4800 cal)/hr GI sheet (ABS ,HIPS plastic fitted with hermerically ,scales compressors operating refrignt R-22 / non CFC suitable for( floor mounting and ceiling mounting ) confirming to IS 1391 ( part 2 ) 92 ( AMDT .1)suitable operation on 230 V,50 HZ single phase AC supply .a.mounting / filtering indoor & outdoor units at their respective location b.Laying Refrigrnt ppe line of reequired lengh connecting both units after drilling holes in the wall thickness copper tube shall be not less than 0.7mmc.insulating the suction pipe with expanded polyurithene foam 5 mm tubeing d .laying 15 mm dia flexvle pvc drain pipe to throw out the condensate water being formed in the indoor e.Leak testing the entire system unit f. Charging refrigent gas the unit g. Suitable electric wiring & swith should be provided with in the 3 meters of the location of uniit Carrier or equivant make
Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay M-1988
Supply and erection of 2 Ton 5 star rated split type airconditioners (6000 cal)/hr GI sheet (ABS ,HIPS plastic fitted with hermerically ,scales compressors operating refrignt R-22 / non CFC suitable for( floor mounting and ceiling mounting ) confirming to IS 1391 ( part 2 ) 92 ( AMDT .1)suitable operation on 230 V,50 HZ single phase AC supply .a.mounting / filtering indoor & outdoor units at their respective location b.Laying Refrigrnt ppe line of reequired lengh connecting both units after drilling holes in the wall thickness copper tube shall be not less than 0.7mmc.insulating the suction pipe with expanded polyurithene foam 5 mm tubeing d .laying 15 mm dia flexvle pvc drain pipe to throw out the condensate water being formed in the indoor e.Leak testing the entire system unit f. Charging refrigent gas the unit g. Suitable electric wiring & swith should be provided with in the 3 meters of the location of uniit
Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay
Supply and fixing of MS stand for fixing outdoor unit
Supply and laying of 5/8" and 3/8" copper pipe (Extra beyond 3 metres supplied with AC unit)
Wiring with 2 x 1.5 sqmm (22/0.3 ) PVC insulated SC unsheated cu.conductor of 1100 V grade in suitable PVC rigid pipe concealedin wall and ceiling with PVC accessories in flush with wall metal box and 6 A 1 way modular switch of in crabtree /legrend make in flush with wall with suitable modular front plate cover for making good of the concealed light point (5 pointper coil) Data A
Wiring with 2 x 1.5 sqmm (22/0.3 ) PVC insulated SC unsheated cu.conductor of 1100 V grade in suitable PVC rigid pipe concealedin wall and ceiling with PVC accessories in flush with modular Plug point with monitoring box combined plate Plastic 6A 5pin interlocking wall socket switch of in crabtree /legrend make in flush with wall with suitable modular front plate cover for making good of the concealed Plug point Data B
Supply and fixing of single box type 4' LED fluorescent fitting complete with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87
Supply and fixing of WT bulk head fitting suitable for 7/9 w LED lamp with guard and LED SD 87
Supply and Fixing of MS fan hook in existing ceiling MR
Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp SD 110
Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall SD 115
Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan SD 120
Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch concealed in suitable MS box in flush with wall and concealed with 3mm thick hylem sheet SD 135
Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour SD 57
Same as SD 209, except 3-1/2 x 25 sq.mm. PVC LTUG armoured cable SD 222
Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection SD 186
Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete SD 235
Supply and fixing of 63A TPNMC switch with suitable angle iron frame work with MS cable entry boxes with earth connection only SD 166
Supply and run of No-8 SWG Cu conductor in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour ( Data C)
Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection SD 76
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry SD 233
Supply and fixing 8 way single pole and neutral MCB DB in sheet steel enclosure with metal door with IP protection with following MCB in flush with wall and making good of the concealed portion with earth connection only .the mcb DB , RCCB and mcbs should with MDS incommer 32 A DP MCB -1 No ,25 A DP ElCB-1 No outgoing 6A to 16 A MCB -4 Nos Data D
Supply, Erection, Testing, Commissioning and Handing over of 1 no 10 persons capacity passenger lift as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location : yatrinivas bulding (Hotel) 2. No of Lift : 1 No 3. Type of Lift : Passenger lift 4. Capacity of Lift : 10 Persons Passenger(680Kgs) 5. Speed : 1 mtr/Sec 6. Type of Drive : Microprocessor based specific variable voltage variable frequency V3F Drive with enhanced ride comfort and micro proccesor based 7. No of floor : G+1 floors 8. Total Travel: 3.3 Mtrs approximate 9. Leveling Accuracy : High levelaccuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel Hairline finish No.4 hair line finish & panels with direct lighting and new beautiful single tile false ceiling with tubular handrail and mirror. 11. Position of Machine: Directly above the lift well. 12. No of Landing Entrance: One in front only. (5 Landing, 5 stops) 13. No of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel.15. Landing Entrance Door: Center opening automatic power door with stainless steel No. 4 hair Line finish with view panel. 16. Lift well: 2000mm (width) x 2700mm (depth) available size. 17. Lift pit depth available: 1600mm 18. Car size: 1100mm wide x 1600mm deep x 2300mm height (Part 1-2000). 19. Car clear opening: 800 mm x 1600 mm (as per IS 14665 (Part-1)-2000). 20. Lift machine room: As per standard specification. 21. Power supply: 415V, 3 phase, 50 cy /sec A.C supply for power and 230V, 50 Hz single phase AC supply for light. 22. Control: Micro processor computer based - simplex collective full collective logic system with / without attendant mode. 23. Car fittings 4 Nos 8W LED recess mount fixture lighting with cross flow fan 24. Lift Well: RCC construction with brick masonry. 25. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 26. Emergency Alarm Bell: Battery operated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automatic charging device. 28. Fireman's switch: To be provided at ground floor. 29. Minor Builders Work: To be provided by lift contractor. 30. Scaffolding: To be provided by lift contractor. 31. Stainless Steel sill angles and facia Plates: To be provided by lift contractor.32. Steel for lift Machinery: To be provided by lift contractor. 33. Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34. Provision of 1+3 EPABX intercom with phone to be provided at the following places,vide i.LiftHead Room, ii. Reception Room and iii. Inside the Lift, by lift contractor. 35. Lift License: Preparation of drawing, Payment of charges to CEIG and Insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor. 36. Automatic rescue device - To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charges inverter under voltage protection system etc. 37. Floor annunciation system with music. 38. Special futures: (a). Infra red door sensor withFull height screen. (b). Full width half height rear panel Mirror. (c).Voltage stabilizer for circuit control. (d). Tubular Stainless Steel hand rail three sides in car. switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 40. Guarantee: Guarantee for the materials & workmanship of equipments complete should be offered by the Lift firm for a period of not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over.
Supply and Installation of 50 inches 4k UHD Smart Television with suitable wall mount ( samsung / Eq make)
Supply and Installation of 43 inches 4k Ultra HD LED Television with suitable wall mount ( samsung / Eq make)
GST Amount for providing Service to Government Contract Works for the above Construction & Maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (Both Construction and Maintenance) above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)
V.S.Constructions India Private Limited
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid