SPECIAL REPAIR OF DINNING HALL MT FOL STORAGE SHED BUILDING NO P 158 P 24 P 25 VEHICLE REPAIR BAY HARDSTANDING DRAINAGE INTERNAL WIRING WITH ALL FITTINGS AT P 52 AND P 116 AND PROVN OF MEAT ROOM 2 NOS SOAKAGE WELL AND ALUMINIUM DOORS AND WINDOW

Amount

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

Demolition of cement reinforced concrete (reinforcement cut as required to facilitate demolition) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:4 complete all as specified and as directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mm thick (Horizontal or sloping), finishing rough the concrete surfaces, complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

5mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 as in roof slab, finished the surface even and smooth without using extra cement, complete all as specified and directed.

S & F for aluminium door of extruded aluminimum section, consisting of frame vertical and horizontal members of size 100mm x 45 mm x 2.5 mm thick with shutter stile 85mm x 45mm x 2.50 mm thick, top middle and bottom rail of size 101.60 mm x 44.5mm with 5.50 mm thick tinted sheets glass and PVC prelaminated particle board 10 to 12 mm thick with alumimium beading and rubber gasket/beading including fixing of hydraulic floor spring one in single leaf or two nos in double leaf door, one mortice lock for aluminium door (each) and two Nos 200 mm long aluminium tower bolts and two Nos aluminium handles D type for each door, fixing with rawl plug including rectification of floor/wall to match the existing surfaces all as specified and directed.

S&F for aluminium for fully gazed window openable shutter with aluminium section, consisting of frame vertical and horizontal members of size 100 mm x 44.45 mm x 1.90 mm thick for frame and section for shutter 45mm x 44.5mm x 1.9mm thick with 5.50 mm thick tinted sheet glass with aluminium beading and rubber gasket/beading clip 3 nos 150 mm long handle 02 nos D type, 75 mm long aluminium butt hinges min 02 nos in each leafb fixing with rawl plug including rectificatioon of jambs floor/wall to match the existing surfaces all as specified and as directed.

35 mm thick 2nd class hardwood plain (Sal/ Hollock) factory made, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats, complete all as specified and as directed.

30 mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

5.50mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, including hacking out old glass panes, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples,complete all as specified and directed.

Mortice lock, brass 4 Levers, vertical type size 100 mm, complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

Steel ventilator with top hung shutter incl hinges, steel peg stay, including one shop coat of red oxide primer, complete all as specified and directed, complete all as specified and directed.

200mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

100 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

300mm long brass ordinary rat tail rod pattern, springs including roller and roller plate fixed to wooden chowkhat, complete all as specified and directed.

150mm long, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, including hacking out old glass panes, complete all as specified and directed.

25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Dismantling water storage tanks of any description, exceeding 250 litres but not exceeding 500 litres and removing from site, complete all as specified and directed.

S&F for Rotational moulded polythylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, complete all as specified and directed.

S&F in repairs 15mm bore bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed.

S&F in repairs 15mm bore stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting, chases, pinning for concealed work etc and making good disturbed surfaces in CM 1:3, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting, chases, pinning for concealed work etc and making good disturbed surfaces in CM 1:3, complete all as specified and directed.

S&F in repairs 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

S&F PVC (SWR) bends 110mm bore dia complete all as specified and directed.

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe including taking down of old one complete all as specified and directed for following bore of pipes.

S&F in repair 2nd class soft wood, weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, complete all as specified.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding (eaves board) to wall fixed with self tapping screws as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-290 (Gde-E-165), complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkali-resistant priming paint, complete all as specified and directed.

Preparation of new plasetered or unplastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash,complete all as specified and directed.

Complete removal of existing treatment of walls and applying two coats of cement base paint, complete all as specifed and directed.

Preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surcaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

Preparation of old decorated CGI sheet surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

S&F for anodised aluminium snap grid of size 605 mm x 605 mm frame work for false ceiling including Hangers 6 mm dia MS rod (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 mm x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false celing grid made of aluminim GI/MS as per specification and drawing complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in surface channel and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm ditto as above, complete all as specified and directed.

75mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified.

Chequered cement concrete tiles of size 200 x 200 x 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

S&F in repair 40mm thick, 2nd class hardwood clean sawn boards or planks, width n exc. 20 cm, planed one side with butt joints and fixed with nails in any situation, complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

35 mm thick, 2nd class hard wood factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

200mm long, mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, complete all as specified and directed.

150mm long, mild steel pressed handles, oval type, stove enamelled black, all as specified and directed.

250mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

2nd class hard wood, as in scantling and similar work, clean sawn, timber framed and fixed in position including dismantling, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

75mm thick, PCC 1:2:4 type B-2 (using 40 mm graded crushed stone aggregate) as in floor laid in alternate bays(size of each panel 1.20x1.20m) including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green and joints filled with mastic filling, including necessary formwork, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Machine Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed

10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying 3mm thick wall care putty, complete all as specified and directed.

35 mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

150mm long, mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, complete all as specified and directed.

75 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

125mm long, extruded aluminium alloy handles, fabricated type, anodised, all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples in repairs, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed.

Fixing only 15mm bore medium grade steel water tubing with all new fittings fixed in walls, ceiling or laid in floors complete, complete all as specified and directed.

Fixing only 20mm bore medium grade steel water tubing with all new fittings fixed in walls, ceiling or laid in floors complete, complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F in repair stainless steel grating doom 125mm dia, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

PVC (SWR) bends 75mm bore dia complete all as specified and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

S&F in repair vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, jointing to flush pipe complete and making good to dismantled/damaged floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed .

S&F in repair vitreous china urinals, bowl type 465x355x265 mm white, providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with flush pipe, grating and union for discharge pipe complete all as specified and directed.

PVC (SWR) vent cowl for 75mm bore pipe and fixed, complete all as specified and directed.

Machine pressed precast coloured concrete interlocking paver block with grey cement and pigment, any shape, size and design as approved by Engr-in-charge confirming to IS 15658-2006 of 60 mm thickness, M-35 grade, laid over and including 50mm thick sand cushion and compacted with mechanical vibrator, all as specified.

100mm thick, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified.

Cement concrete in foundations 1:2:4, type-B2 (40mm graded stone aggregate), as in hardstanding laid in panels finished even and smooth without using extra cement, complete all as specified and directed.

Forming of 20mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A' in 150mm thick flooring, complete all as specified and directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A', complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in any type of soil, complete all as specified and directed.

All as per srl item No-109 here in above, depth exc 1.50m but not exc 3.0m, complete all as specified and directed.

Brick work with sub class 'B' bricks in one brick thick honey-comb walling, built in cement mortar 1:4, complete all as specified and directed.

Plain cement concrete bed 1:3:6 type C-2 (using 40mm graded crushed stone aggregates)to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipe, complete all as specified and directed.

Salt glazed stone ware drain pipe of 150mm bore (internal bore) garde 'A' laid in trenches and jointed, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and as directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

Precast cement concrete type 1: 2: 4, type-B1 (20 mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm bore pipe, all as specified and directed.

Walling of random rubble masonry with best quality stone, uncoursed, well bonded, bedded and solidly hearted and built in CM 1:4, all as specified and directed.

All as per srl item No-119 here in above but except stones, complete all as specified and directed.

Flush pointing to random rubble masonry, uncoursed or brought upto courses in CM 1:3, complete all as specified and directed.

Surface dressing not exceeding 30 cm deep and averaging 15 cm getting out in hard/dense soil, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash,complete all as specified and directed.

Hard core of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

100mm thick, PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, etc., and similar small articles, conforming to Fe-290 (Gde-E-165), complete all as specified and directed.

Mild steel work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed.

Vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets and including 32mm dia PVC waste pipe, waste coupling and 15mm bore dia pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed, complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation, complete all as specified and directed.

4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

Aluminium partition powder coated aluminium tube of section 114mmx44.5mmx1.5mm thick at bottom and remaining horizontal and vertical section 44.5mmx45mmx2mm thick aluminium clip ,rubber beading aluminium nut and bolts etc including 5mm thick plain glass and 12mm thick prelaminated particle board (both side laminated)spacing of glazed aluminium tube in horizontal 75cm max and vertical 90cm max complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including unscrewing from board fitting and fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc complete all as specified and directed.

Concealed point wiring complete with 1.5 sqmm 1100 graded PVC FRLS (Multistrand) insulated unsheathed copper conductor, PVC conduit not less than 20mm dia concealed, including cutting chases, finishing by means of cement mortar making good to existing surface of the wall and touching with three coats of existing colour of wall and making good disturbed surface complete sunk in pressed steel terminal boxes of required size not less than 1.6mm thick factory made and factory painted with top cover 3mm thick plastic laminated sheet fixed with brass screw and washers with all accessories including single core multistranded copper conductor 1.5Sqmm size cable as earth continuity wire connected to common earth dolly to modular concealed box and white cover plate of required nos and required size for housing switches, sockets etc for one light / fan/ bell point controlled by one switch one way and making good disturbed surfaces with CM (1:3) to match with the existing surface, complete all as specified and directed.

All as per srl item No-134 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No-134 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No-134 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

Switch piano flush button types 5/6 Amp, single pole, one way complete all as specified and directed.

Switch socket combination 2 in 1, outlet 5 pin, 5 Amp flush type, universal, complete all as specified and directed.

Switch socket combination 2 in 1, 5/6 pin, 5 and 15 Amp, flush type universal complete all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate, straight/ angular, suitable for batten fittings, complete all as specified and directed.

Supply, installation, testing and commissioning of decorative ultra slim linear LED in replacement of 20 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack including LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed. Make : Havells Cat Part No LHEXBLP7PN1W020 or Equivalent in C&S/Bajaj/Halonix.

Supply and fixing in repair LED 9 watt pin type bulb complete all as specified and directed.

Supply and fixing in repair, 10 Watt LED, environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs, complete all as specified and directed. Make : Havells Cat Part No HEXAFT10WLED857SSYMBOPC or Equivalent/C&S/Bajaj.

Supply and fixing in replacement MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways, IP-43 protection,fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply & fixing in replacement of for MCB single pole 240 volts 6 to 32 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed.

Supply & fixing in replacement of for MCB double pole 240 volts 6 to 32 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed.

Supply and fixing in replacement electronic dimmers, 450W, 250V flush type on the exiting phenolic laminated sheet etc. as required, complete all as specified and directed.

Sub main wiring with two single core PVC insulated flexible copper conductor cable of size 6 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6 Sqmm as earth lead in & including PVC casing capping medium grade 2mm thickness ISI marked incl taking down old unsv complete all as required at site or directed.

Supply & fixing in replacement of MCCB distribution board TPN, 8 way vertical double door sheet steel enclosure powder coated with and including 100 Amp rated bus bar with neutral links,100 Amp 3P 16kA 415 Volt V-tec MCCB, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply laying connecting and testing in replacement of 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 Sqmm normal cross section 4 core including suitable size lugs laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers and remove unsv cable complete all as specified and directed.

S&F in replacement 40mm dia bore galvanized iron tubing, light grade including all fitting for cable protection etc laid in floor, trenches or fixed to poles with clamps etc complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by (-) 14.5% (minus). (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Supply & fixing in replacement MCB Distribution board , 240 volts single pole and neutral , double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 8 ways, IP-43 protection, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection and making good disturbed surfaces of walls etc, including two coats of white/colour washing/distempering etc to match the existing surface, complete all as specified and directed.

Supply & fixing in replacement of for MCB double pole 240 volts 40 to 63 amps as per site requirement , with rupturing capacity 10 KA as per IS-8828-1996 (IEC-60898), biconnect upper and lower terminals , integrated label holder to ensure circuit identification, complete all as specified and directed.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/Polycarbonate, isolated body, complete all as specified and directed.

Supplying installing, commissioning testing in repair LT cubical feeder pillar box outdoor kiosk type made out of CRCA sheet 3.15mm thick ,3 phase 4 wire 50 C/S AC with aluminium bus bar of 150 Amps rating fixed on insulators for incoming & outgoing taping complete double door type with locking arrangement fixing on PCC platform with suitable nuts, bolts duly painted with two coats of synthetic enameled paint over a coat of red oxide primer, comprising with MCCB 100 Amps TPN 50Hzs, 25KA ( 01 Nos) in incoming and MCCB 63 Amps TP 25KA (01 Nos), cable for service connection complete all as specified and as directed.

FG CONSTRUCTION