PROVISION OF TRAINING SHED AT ZONE-8 OF MED REGT UNDER AGE (I) TALBEHAT

Amount

Surface excavation not exceedig 30cm deep and averaging 15cm deep and getting out in Hard/dense soil.

M&L for cement concrete in 1:4:8 type D2 as in foundation filling and mass concrete complete all as specifed and directed.

Excavation in tranches in soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out for foundation.

Removing excavated materials not exceeding 50 m and depositing where directed at a level n exc 1.5 m above the starting point

Returning filling in including spreading levelling, watering and well ramming in layers not execceding 25 cm in soft/loose soil.

M&L for brick work with fly ash bricks in modular size straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for plastering 15mm thick in CM 1:6 on fair face of wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L for plastering 15mm thick in CM 1:4 on fair faces of wall ,finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coat of oil emulsion distemper over a coat of primer with 3mm thick wall care putty complete all as specified and as directed,

M&L for providing 100mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregates as in sub base of flooring complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams and similar work complete all as specified and directed

Form work to sides of pillars,posts ,columns (square/rectangular)or any other shape for fair finished surfaces complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded stone aggregate Foundations, including rafts,footings, foundation beams;plinth beams; bases for column,lintel band,roof beam etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in chajjas complete all as specified and as directed.

Form work to edges of concrete flats, roofs exc 10 cm wide and n exc 20 cm wide/Lintel band,lintel beam/Roof band etc complete all as specified and directed for rough finished surface.

M&L for RCC 1:2:4 type B1 using 20mm grades stone aggregates as in column, pillars,posts etc complete all as specifed and directed.

M&L for RCC 1:2:4 type B1 using 20mm grades stone aggregates as in beams,cantilevers,lintel band/roof band etc complete all as specifed and directed.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregates as in coping/benching in roof,rounded or chamferred complete all as specified and directed.

M&L mild steel work in tubular trusses including special shaped washer etc complete using ERW of induction butt welded tubes including painting with one shop coat of zinc chromate primer conforming to IS 1161-1979 grade St-240 all as specified and directed.

M&L for hand rails ,half round or other stock section or core for wooden hand rails,straight portion,drilled and counter sunk for balusters running bars,for doors,balusters,nozing to steps,including embedding in concrete and screwing etc,wind ties for roof including securing bolts,posts or struts including cutting tops to shape as required ,purling and rafter complete including applying one shop coat of zinc chromate primer all as specifed and directed. conforming to Fe-290 Grade E-165

M&L for preparation new steel surfaces and applying two coats of synthetic enamelled paint over a coat at red oxide primer complete all as specified and directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated sheet steel 0.50mm thick on an colour having tensile strength of 550Mpa as in roof covering /cladding to wall,fixed with self tapping screws all as specified and as directed.

All as per item No 22 above but plain pre-painted galvalume aluminium zinc coating GI based sheet as in ridge complete all as specified and as directed.

M&L for hard core of guage n exc 63mm brocken stone agts / boulders ,deposited,spread and levelled with well ramming in layers n exc 15cm thick all as specified and as directed.

M&L for applying two coats of exterior emulsion paint over a coat of primer including preparatory work complete all as specified and as directed.

M&L for moorum /red bajri filling in floors or paving laid in layers n exc 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection / path finished even & smooth with out using extra cement and the like all as specified and directed.

M &L for coloured non skid ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed in CM (1:4) complete all as specified and as directed.

M&L galzed colour ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster in CM 1:4

S&F TMT bars 10 mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire [annealed] not less than 0.9 mm dia or scruing with clips complete all as specified and as directed.

Same as per item No 30 above but 6 mm to 8 mm dia of TMT Bars.

S&F 35mm thick factory made glazed and skelton shutter 2nd class hard wood rails and stiles planed framed and open rebated and prepared to receive glass ,guage etc (without sash bars) with cut and mitred beads for securing glass etc size member of shutter as specified in SSR part-I section and clause 8.24(a) fixed to chowkhats complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates of size 125 mm x 60 mm, including necessary fixing lugs ,hinges ,lock strike plate etc complete all as specified and as directed.

S&F 250 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or exturded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete as directed

S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long (ISI marked) complete all as specified and directed.

M&L for 100mm MS butt hinges medium weight ,cold rolled mild steel and fixed to door frame complete all as specified and as directed.

M&L for aluminium alloy handles 150mm ,fabricated type anodized complete all as specified and as directed.

M&L of E-board 'Everest' Make 600 x 600 x 4 mm thick, white pre-laminated self-embossed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed gird with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall comprise of main runner made from 0.33mm thick GI sheet and of size 24 x 32 x 3000mm and spaced at 1200 mm centre to centre screwed fixed to the soffit of structure by hanger as approved at 1200 mm maximum centres. Hangers of GI wire 2 run of 2mm dia to be fixed by approved rawl plug, level and jesters and screws etc. The last hanger at the end of each main runner shall be greater than 450mm from adjacent wall. Flush Fitting of 1200 mm long cross tee (with double stitching) to be interlocked between main runners at 600mm centre to centre to form 1200 x 600 mm modules, cross tee longer than 600 mm to be supported independently. 600 x 600 mm modules to be formed by fiting 600mm long cross tee centrally between 1200 mm cross tee. The perimeter wall angel shall be of 0.45 mm thick GI sheet of size 19mm x 19 mm and 3000 mm long of white powder coated all as specified by manufacturer instruction finishing the surface by applying two coat of oil bound distemper

M &L for steel windows with side hung shutters including projecting type hinges with steel handles and steel peg stay complete with glazing bars, dovetails or welded complete all as specified and directed by Engr-in-Charge.

M&L for painting to wooden surfaces with two coats of synthetic enamelled paint over a coat of pink primer on new surfaces complete all as specified and directed.

M&L for point wiring suitable for modular fittings concealed type with 1.5sq mm FRLS insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl PVC rigid conduit not less than 20mm dia with its accessories etc for the following:- Note : 1. In RCC ceiling/column, conduit to be placed before casting of RCC as directed by Engr-in-Charge. 2. Cost of white cover plate and metal flush mounting box of suitable module as per site requirement shall be measured and paid seperately. 3. Make of white cover plate and metal flush box is same as switch/socket.

One light/fan controlled by one switch 5/6 Amps single pole one way

One socket outlet 6 Amps controlled by one switch on the same board.

One socket outlet 6 Amps controlled by one switch on indipendent board.

All as per item No 41 here-in-before but one 16A socket point controlled by one 16A switch on independent board with 2.5 sqmm wires..

S&F Modular Switch single pole one way 6 Amp 1 module, 240 volt. Make : Leader, Havells, Schneider, Indo Asian.

S&F Modular Switch single pole one way 16/20 Amp 1 module, 240 volt. Make : Leader, Havells, Schneider, Indo Asian.

S&F for socket 2 & 3 Pin 6 Amp flush type with shuttered 6 Amp Modular type suitable for 2 module 240 volt. Make : Leader, Havells, Schneider, Indo Asian.

S&F for socket 2 & 3 Pin 6/16 Amp flush type, with shuttered 6 Amp Modular type suitable for 2 module. Make : Legrand, Havells, Schneider, Indo Asian.

S&F for white cover plates with frame suitable for modular switches/sockets of 3 module complete all as specified.

S&F for white cover plates with frame suitable for modular switches/sockets of 4 module complete all as specified.

S&F for white cover plates with frame suitable for modular switches/sockets of 6 module complete all as specified.

S&F for metal flush mounting box 3 module complete all as specified.

S&F for metal flush mounting box 4 module complete all as specified.

S&F for metal flush mounting box 6 module complete all as specified.

S&F ceiling rose 3 phase/PVC/Polycarbonate, isolated body complete all as specified. Make : Legrand, Havells, Schneider.

S&F Fan Step regulator, 120 Watt, 2 Module socket type complete all as specified. Make : Leader, Havells, Schneider.

M&L for sub main wiring with two single core FRLS insulated of size 4 sqmm unsheathed copper conductor 1100 volt grade multistandard and incl drawn through and including non metalic rigid pvc conduit and couduit accesssories of 25 mm external dia and conduit accessories of ISI marks medium grade including 4.0 sqmm FRLS copper wire for earth continuity wire and connected of common earth dolly complete all as specified. Note : (a) One run of conduit two run of 4 sq mm FRLS copper conductor & one run of 4.0 sq mm FRLS copper earth wire is measured as one unit. (b) In RCC ceiling/column, conduit to be placed before casting of RCC as direction of Engr-in-Charge

M&L for sub main wiring with two single core FRLS insulated of size 2.5 sqmm unsheathed copper conductor 1100 volt grade multistandard and incl drawn through and including non metalic rigid pvc conduit and couduit accesssories of 25 mm external dia and conduit accessories of ISI marks medium grade including 2.5 sqmm FRLS copper wire for earth continuity wire and connected of common earth dolly complete all as specified. Note : (a) One run of conduit two run of 2.5 sq mm FRLS copper conductor & one run of 2.5 sq mm FRLS copper earth wire is measured as one unit. (b) In RCC ceiling/column, conduit to be placed before casting of RCC as direction of Engr-in-Charge.

S&F sheet metal enclousure for MCB DB Triple pole and neutral 4 way with 200 Amps rated bus bar 440 volts, IP-43, IK09, double door (Metallic) type complete all as specified. Make: Legrand/Hager/Schneider, Indo Asian.

S&F MCB SP 6 to 32 Amps 240 volts 'B' series, 10 KA, 50 Hz, complete all as specified . Make : Legrand/Hager/Schneider/ Indo Asian.

S&F MCB TPN 40 Amps 240 volts 'C' series, 10 KA, 50 Hz, complete all as specified. Make: Legrand/Hager/Schneider/Indo Asian.

M&L for Earthing complete with galvanized earth plate electrode 600x 600 x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvenised earth lead wire of 4 mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 3 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work PCC(1:3:6) type C-1 pit with precast RCC Cover slab 40 mm thick in PCC(1:2:4) type B-0 reinforced with 6 mm dia MS bars @ 100 mm c/c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe including connected to earthing point bar made of MS Flat (40x6) mm grouted in to wall complete all as specified and as directed.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in MS conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 sqmm FRLS insulated (green) copper conductor complete all as specified and as directed.

Supply and fix LED bulkhead luminaire in die-cast aluminium alloy body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection suitable for and including provision of 10W retrofit LED bulb, full white with B22 lamp holder complete all as specified and directed by Engineer-in-Charge. Make : Havells - Model RUGBYNEONFT10WLED760SSYMBOPC or Philips / Wipro / Bajaj / Osram / Surya /CG.

Supply and fix LED batten with CRCA sheet steel body box type pre-wired suitable for and including provision of 1x20 Watt (4 feet) retrofit LED tube with PC body, full white and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed by Engineer-in-Charge. Make : Havells- Model ENDURALINEARNEOBS20WLED865SPCWH or Philips / Wipro / Bajaj / Osram / CG

Supply and fix recessed mounted LED panel light 2'x2' size, 36 watts, full white with electronic driver in CRCA sheet steel body with polycarbonate diffuser suitable for Amstrong / grid false ceiling complete fix fixing accessories and all as specified and directed by Engineer-in-Charge. Make : Havells - Model PLUTOSURFACE2X2PLS34WLED857S or Philips / Wipro / Bajaj / Osram.

Supply & Fixing ceiling fan complete in all respect AC single phase 230 volts, 50 Hz, of size 1200 mm sweep, BEE 5 star rated & all fixing accessories complete all as specified and directed. Make : Havells, Orient, Crompton Greaves

S&F desert cooler electric driven (single phase) having nominal air flow capacity of 5000 cum per hour complete with kit fan motor 450mm sweep 1350/1400 RMP. Make : Everest / Summer Cool / Khatian and Submersible water lifting pump of capacity 1.25 M head 230V AC Make : Bansal including loclaly fabricated cabinet with three side panels front, top and tank including vertical mention made out 22 SWG PGI sheet of size not more than 660 x 660 x 825 mm (26" x 26" x 32.5") with double diversion grills and grill box suitable for 18" sweep fan and making holes with fixing arrangement including 4 way PVC distributor, PVC pipe 3 to 4 Mtr for spray water, wood wool pads, electrical wiring for fan and pump controlled seperately with 5 amp Piano type switch and indicator etc complete all as specified.

M&L in replacement of cable XLPE insulated heavy duty electric cables 16 Sq mm 4 Core with Stranded alluminium conductor, 1100 volts grade, passing through trenches/ducts/pipes and climbing on poles/walls including fixing with proper size of alluminium lugs. NOTE:- 1. Excavation and earth work to be measured and paid seperately. Make : Asian Cables (RPG) / Havells India Ltd/Gloster / Polycab / Finolex / KEI / Universal

Supply and laying or fixing GI tubes light grade 40 mm bore for cable protection, in support of cables, on pole/wall/laid in floor/in trenches complete all as specified. Make : JINDAL/TATA/SURYA

Excavation in in trenches not exceeding 1.5 mtrs wide & not exceeding 1.5 mtr in depth in soft or loose soil & getting out complete all as specified and directed.

M&L for Sub class 'B' bricks laid dry width wise across the line of cable in treanchs as cable protection complete all as specified and directed by engr in charge.

M&L for laying of fine, clean sand (river sand) free from sharp materials in trenches for cushioning of cable 8 cm thick under cable and 15 cm thick over the cable including gently punning complete all as specified and directed. Note:- The total thickness of sand shall be measured 18 cm after punning.

M/S R.S.BUNDELA & SONS

M/S Kharya Associates