CA NO GE (I) (AF)/SHL/ OF 2020-2021 REPAIR/REPLACEMENT TO ROOF, CEILING, WALL PLASTERING, FLOORING, JOINERY, FLOOR/WALL TILING, INTERNAL WATER SUPPLY/PLUMBING, PLINTH ETC AT HQ EAC (U), UNDER GE(I) (AF) SHILLONG

Amount

Note : All unserviceable materials obtained out of demolition/dismantling/taking down (other than those for which credit catered under Schedule of credit) shall be disposed of outside MoD Land. Quoted rates against respective item shall deemed to include for same.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed.

Demolition of unreinforced cement concrete in any position not otherwise specifically provided for and removal all rubbish material complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position complete all as directed.

Dismantling of timber fillet, rails, post, rafters, purlins, etc. under 40 Sqcm in section unframed or framed work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area not exc. 1 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area exc. 1 sqm & n.exc 2.00 sqm each complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beeds complete all as specified and directed.

Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site complete all as specified and directed .

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. (Note :- The length shall be measured along the centre line including fittings and accessoires).

M & L for PCC 1:5:10 type E-2 using 40 mm graded crushed stone aggregate as in foundation, filling under floor, in sunken floors etc complete all as specified and directed.

M&L for cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands copping/cills, bed block for embedding hold fast etc including necessary form work weathering, slightly rounded or chamfered angles and throating complete all as directed .

Supply only integral water proofing liquid complete all as directed.

M & L for second class hard wood clean swan as in scantling fixed in timber framed work or independently complete all as specified and directed.

M & L for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and directed.

S & F of 40mm thick second class hardwood (CHIR) boarding as in floors and skirting planed one side and edges tongued and grooved or rebated and fixed with nails complete all as specified and directed.

M & L for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35mm thick IInd Class Hard wood, plain framed, panelled door shutters, two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces (as ordered). The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 35mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 30mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, In opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed for following sizes:-

75 mm long.

100mm long.

S & F 100mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 150mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 100mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolts, plate type with bolt not less than 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as directed

S & F in repairs continuous (Piano) hinges width of flaps (when open) 40mm, MS, bright finish or electro galvanised complete all as specified and directed.

S & F in repairs ball catches with 8mm dia steel ball and brass body and skirting plate including letting in and fixed complete all as specified and directed.

S & F in repairs aluminium (Die cast) body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as directed.

S & F in repairs 140mm (overall length of cover plate), floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F in repairs brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys complete all as directed.

S & F in repair for powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends fixed with PVC rawl plug and steel screws on walls/beam, complete all as directed.

S & F in repairs of Chromium plated Knob (mini round handle) for drawer (of kitchen CB/books shelfs) complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as directed.

S & F mild steel conforming to Fe-290 Gde E-165 as in wind ties for roof, or for hold fasts, clamps etc and similar small articles including securing bolts, drilling hole and similar work complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 18/19 mm thick Prelaminated particle, board, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination and alround covered with 6mm thick teak wood beading/lipping fixed with screwed to timber frame complete all as directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in levelling coarse of floors, surfaces finished even and fair complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M & L for joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exceeding 0.36 sqm, as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L 16-18 mm thick granite slab/tiles (of any type table rubbed and polished) in steps jambs pillars, window cills, cooking platforms and like set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with complete all as specified and directed.

M & L Rounding to edges of stone slabs one edge, such as in steps,cooking platform, and other similar situations complete all as specified and directed.

M & L for rendering 5mm thick in CM 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM 1:4 on fair faces of brick masonry/concrete surfaces, mixed with water proofing liquid @ 150ml per 50 Kg bag of cement and finished even and smooth without using extra cement complete all as specified and directed. (Note :- Supply only Water Proofing Liquid shall be measured and paid separately)

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all specified and as directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares exc 0.5 sqm in each pane complete all specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1mm thick wall care putty complete all as directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

M & L for preparing old plastered surfaces of wall and applying one coat of oil bound distemper complete all as per specified and directed.

M & L for complete removal of existing treatment on walls including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered and other surfaces of walls, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of oil bound distemper including a coat of 1mm thick wall care putty complete all as specified and directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

Material and labour for preparation of newly plastered surfaces of wall, applying a coat of 1mm thick wall care putty and applying two coats of weather proof acrylic paint over one coat of exterior grade acrylic primer complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Beger, Acroguard 3X of Acro paint.

M & L for French Polishing on old wooden or wood based surfaces of any description width or girth including cleaning and preparing the old surface with two or more coats complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for treating sunken floor surfaces with two coats (one priming coat and one finishing coat) of water proofing chemical PIDIFIN 2K of Dr Fixit (or any other brand approved by GE) all as per Manufacturer's instructions complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Fixing only old serviceable steel water tubing, galvanized, medium grade, with all new fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

S & F 15mm bore bib tap cast copper alloy fancy type chromium plated long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore stop valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

M & L in repair for 15 mm dia cast copper alloy Chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8712 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs 15 mm dia cast copper alloy Chromium plated one way Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8710 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs 15 mm dia cast copper alloy Chromium plated two way Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8711 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair 15 mm dia Brass CP, wall mixer 3 in 1 system with provision for both hand and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange (without Hand and overhead shower) (Concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-281KN of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs 15mm bore sink mixture for mixing hot and cold water chromium plated fancy type with swinging casted spout (wall mounted model) with connecting legs & wall flanges two joints to steel pipe or union and plugging/screwing to wall complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-309KN of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs 15mm bore central hole Basin mixture for mixing hot and cold water chromium plated fancy type without popup waste system with 450mm long barided hoses complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-167KNB of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs Hand Shower (Health Faucet) with 8mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed. (Product Code & Make :- Cat Part No ALD-573 of JAQUAR or equivalent model of other makes listed in list of makes)

S & F in repairs Hand Shower of 95mm dia round shape multi flow (ABS body chrome plated with grey face plate) with rubit cleaning system with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. (Product Code & Make :- Cat Part No HSH-1739 of JAQUAR or equivalent model of KOHLAR/Roca) (Product Code & Make :- Cat Part No HSH-1739 of JAQUAR or equivalent model of other makes listed in list of makes) (Note : The contractor shall deposit with Engineer-in-Charge these original purchase voucher and product guarantee/warrantee certificate in original for the period as per policy in vogue of manufacturer to obtain service from manufacturer during the period of guarantee/warrantee.)

M & L for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm dia complete all as specified and directed.

S & F in repairs 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified and directed.

S & F PVC (SWR) pipes 110mm bore size single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen sink with plugs, washers and wastes, including bedding cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, over all size 915mm x 460mm bowl size 410 x 330mm x 160mm, complete all as specified and as directed.

S & F in repairs 40mm dia waste coupling of PTMT (half or full threaded) minimum weight 60 gms complete all as specified and directed.

S & F 500 litres capacity rotational moulded HDPE water storage tank tripple layer (Cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. Note : PVC tanks shall be ISI marked and having two layers.

S & F 20mm dia, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repairs 20mm dia, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

M&L for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnectings and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres complete all as specified and directed.

S & F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

S & F in repairs vitreous china wash basin OVAL type of size 195x600x425mm with 16 to 18mm thick granite counter including cutting for and pinning in ends for bracket, and waste fittings 32mm including waste pipe, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed. Note : Granite stone for counter shall be measured and paid separately under respective item of BOQ.

S&F in repair single piece Suite white Vitreous china wash down water closet pan (pedestal pattern) with integral Vitreous china flushing vistern including plastic water closet seat and cover,complete all as specified and directed. (Product Code & Make :- Cat Part No C844A Qube of Parryware or equivalent model of other makes listed in list of makes).

S & F in repairs PVC waste pipe 32mm bore fixed to waste coupling of wash hand basin complete all as specified and as directed.

S & F in repairs PVC waste pipe 40mm bore fixed to waste coupling of kitchen sink complete all as specified and as directed.

S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repairs plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs chromium plated towel rail complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-40 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs chromium plated toilet paper holder with flap complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-38 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs glass shelf 500 x 125mm with decorative and ornamental side supports and front lining of chromium plated fixed with screws and glass with as shelf supported over frames all as specified and all as directed. (Product Code & Make :- Cat Part No. BEA-45 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair corner glass self of size 300mm radius (with brass chromium plated brackets) fixed in the walls with necessary screws etc. complete all as specified and directed. ((Product Code & Make :- Cat Part No. BEA-44 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs PTMT alloy toilet cabinet with mirror of overall size 622 x 422mm and fixed to wall complete all as specified and directed. (Product Code & Make :- Cat Part No. 556 of Make Prayag or equivalent model of other makes listed in list of makes).

M/S BISWA CONSTRUCTION

R K CONSTRUCTION

M/s Gupta Construction