C/o RCC Double Unit Type-II and III Qtrs at Naharlagun (SH- Type-III Double Storey 6 Block of 4 Units).

Amount

(SH:- Ground Floor)

Earth work in earth in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50m and stacking the excaveted soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of founding etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Re-filling excaveted earth in foundation and plinth etc, in 15 cm layer including ramming and watering etc, complete. Qnty 1/6 of excaveted soil.

Filling in plinth with sand under floors including watering, ramming,consolidating and dressing complete

Random rubble masonry with hard stone in foundations and plinth in cement mortar 1:6 (1 cement sand : 6 fine sand) including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 stone aggregrate 20 mm nominal size) at pinth level.

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) exc;uding the cost of centring and shuttering in : a) Foundations and plinth.

Providing and laying DPC 50 mm thick with cement concrete 1:2:4 ( 1 cement : 2 sand: 4 course aggregate 20 mm nominal size.

Applying a coat of hot bitumen (mashplate 80/100 or equivalent ) using 1.70 Kg per Sq.m. On damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Reinforced concrete work in foundations, footing,bases of columns etc and mass concrete excluding cost of centring, shuttering and reinforcement in a) M20 ( 1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roofs, landings and balconies up to floor two level finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in stair case ( excluding landings) except spiral cases including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Centering and shuttering including strutting propping etc and removal of form work for: a) Foundation, footing,Bases of column etc.for mass concrete

b) Walls (any thickness) including attached pilaster, butteresses, pinth ans string course.

c) Suspended floors, roofs landing shelves and their supported, balcony and chajjas (3.5m height)

d) lintels, beams, girder, bressumers and cantiliver

e) Stairs ( excluding landing) except spiral stair case.

Reinforcement of RCC work including bending, binding and placing in position complete, cold twisted bars.

Half brick masonry ( with best available local bricks) in cement mortar 1:3 ( 1 cement : 3 coarse sand) in foudation and plinth

Providing and fixing MS fan clamp type 1 pf 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during laying including paiting the exposed portion of loop all as per standard design complete.

Chequrred terrazo tiles 22mm thick with marble chips of size upto 6mm in floor on 25 mm thick bed mortar 1:3 '9cement : 3 coarse sand) joint with neat cement slurry mixed with pigment to the match the shade of the tiles including rubbing and polishing compete.a) medium shade using approximately 50% white cement and 50% ordinary

White glazed tiles 5mm thick in flooring , skirting, risers of step and dado in 12 mm thick cement plaster 1:3 (1 cment : 3 coarse sand ) painted with white cement slurry

20 mm cement plaster 1:3 ( 1 cement: 3 fine sand). (in wall)

6 mm cement plaster to ceiling 1:3 (1 cement : 3 fine sand)

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering (two or more coats ) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Making plinth protection with 2nd class brics on edge in cement mortar 1:6 (1 cement : 6 fine sand) over 7.5 cm bed of dry bricks aggregate 40 mm normal size rammed consolidated and grouted with fine sand and the top of the bricks pointed with cement mortar 1:2 (1 cement : 2 fine sand)

Constructing of cement concrete drain 30 sm wide and 23 cm deep in cement concrete 1 : 3 :6 ( 1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar 1: 3 (1 cement : 3 fine sand ) including shuttering complete.

Providing and laying cement concrete 1 : 5 : 10 ( 1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW pipe including bed concrete 15 cm thick as per standard design. a) 200 mm dia S W pipe

(SH:- Ist Floor)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. 1 : 1.5 : 3 /1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roofs, landings and balconies up to floor two level finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in stair case ( excluding landings) except spiral cases including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete, cold twisted bars.

Centering and shuttering including strutting proppinf etc and removal of form work for: a) Foundation, footing,bases of columns etc and mass concrete

b) Wall ( any thickness) including attached plaster, buttresses plinth and string course.

c) Suspended floors, roofs landing shelves and their supported, balcony and chajjas

d) Stairs ( excluding landing) except spiral stair case.

Half brick masonry ( with best available local bricks) in cement mortar 1:3 ( 1 cement : 3 coarse sand) in foudation and plinth

Providing approved best available local wood ( Class - B II ) work in frames of doors, windows clerestory windowa and other frames wrought framed and fixed in postion

Providing and fixing panelled , glazed or panelled and glazzed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws.a) 40 mm thick best available local wood class - B I

Providing and fixing of two track slidind windows, concealed lock with natural colour aluminium, 5mm glass and necessary

Providing and fixing of anodised aluminium framed door with 2.5 inch x 1.5 inch chowkhat with 2 inch door frame and 12 mm thick are laminated particle board door closer door handle.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary screws etc complete

Providing and fixing aluminium slide door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing aluminium Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc. Complete. c)150x10 for window

Providing and fixing aluminam Handles anodised transparent or dyed to required or shade with necessary screws etc complete.a) 125 mm

Providing and fixing MS hooks and Eyes. a)300mm

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing 12 mm thick and 150 mm wide pelmet with 25 mm dia wooden curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete. a) Timber class - A IV

Providing and fixing position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and raced with flat iron diagonals 20 mm x 5 mm size with top and botttom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during laying including painting the exposed portion of loop all as per standard design complete.

Providing and laying Vitrified tiles in different sizes( thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S 15633, of approved make, in all colours and shade laid on 20 mm thick cement mortar 1:3 including the joints with white cement and matching of matching pigment., b) size of tiles 600x600 mm

White glazed tiles 5mm, thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand ) painted with cement slurry.

20 mm cement plaster 1 : 3 ( 1 cement : 3 fine sand ) (in wall)

6 mm cemeent plaster to ceiling 1 : 3 ( 1 cement : 3 fine sand).

Appying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering ( two or more coats ) with oil bound washable distemper of approved brand manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats ) to give an even shade.

Providing and fixing PVC pipes with Brass UnionA) 30cm length a) 15 mm nominal bore.

Providing and fixing Non Return Valve of approved qualitya) 25 mm nominak bore.

Providing and fixing brass bib cock of approved quality.a) 15 mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm lenght. a)15mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm length.A) 30cm length a)20 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet a) 100mm dia

b) 150 mm dia

Providing and filling sand all round GI pipes in external work. a) 20mm dia.

Providing and fixing white vitreous china water closet squating pan ( Indian type WC pan ) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern ( of approved make ) with fittings RS or CI brackets, #@ mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).a) 750x20 mm

Providing and fixing sand cast iron/cast iron (spun) soil, waste and vent pipes. b)75 mm dia..

Providing and fixing sand cast iron heel rest sanitary bend. b) 75mm dia.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. b) 80x80x80 mm

Providing and fixing sand cast iron single equal plain junction of required degree.b) 80x80x80 mm

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vwnt arm complete including cost of cutting and making good the walls and floors.a) 100mm inlet and 100 mm outlet

(SH:- 2nd Floor)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. 1 : 1.5 : 3 /1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roofs, landings and balconies up to floor two level finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in stair case ( excluding landings) except spiral cases including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete, cold twisted bars.

Centering and shuttering including strutting proppinf etc and removal of form work for: a) Foundation, footing,bases of columns etc and mass concrete

b) Wall ( any thickness) including attached plaster, buttresses plinth and string course.

c) Suspended floors, roofs landing shelves and their supported, balcony and chajjas

d) Stairs ( excluding landing) except spiral stair case.

Half brick masonry ( with best available local bricks) in cement mortar 1:3 ( 1 cement : 3 coarse sand) in foudation and plinth

Providing approved best available local wood ( Class - B II ) work in frames of doors, windows clerestory windowa and other frames wrought framed and fixed in postion

Providing and fixing panelled , glazed or panelled and glazzed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 40 mm thick best available local wood class - B I

Providing and fixing of two track slidind windows, concealed lock with natural colour aluminium, 5mm glass and necessary

Providing and fixing of anodised aluminium framed door with 2.5 inch x 1.5 inch chowkhat with 2 inch door frame and 12 mm thick are laminated particle board door closer door handle.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary screws etc complete

Providing and fixing aluminium slide door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. A) 300 x 16 mm

Providing and fixing aluminium Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc. Complete. c)150x10 for window

Providing and fixing aluminam Handles anodised transparent or dyed to required or shade with necessary screws etc complete.a) 125 mm

Providing and fixing MS hooks and Eyes. a)300mm

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing 12 mm thick and 150 mm wide pelmet with 25 mm dia wooden curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.a) Timber class - A IV

Providing and fixing position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and raced with flat iron diagonals 20 mm x 5 mm size with top and botttom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during laying including painting the exposed portion of loop all as per standard design complete.

Providing and laying Vitrified tiles in different sizes( thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S 15633, of approved make, in all colours and shade laid on 20 mm thick cement mortar 1:3 including the joints with white cement and matching of matching pigment.b size of tiles 600x600 mm

White glazed tiles 5mm, thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand ) painted with cement slurry.

20 mm cement plaster 1 : 3 ( 1 cement : 3 fine sand ) (in wall)

6 mm cemeent plaster to ceiling 1 : 3 ( 1 cement : 3 fine sand).

Appying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering ( two or more coats ) with oil bound washable distemper of approved brand manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats ) to give an even shade.

Providing and fixing PVC pipes with Brass Union. A) 30cm length a) 15 mm nominal bore.

Providing and fixing Non Return Valve of approved quality a) 25 mm nominak bore.

Providing and fixing brass bib cock of approved quality. a) 15 mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm lenght.a)15mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm length.A) 30cm length a)20 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet a) 100mm dia

b) 150 mm dia

Providing and filling sand all round GI pipes in external work. a) 20mm dia.

Providing and fixing white vitreous china water closet squating pan ( Indian type WC pan ) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern ( of approved make ) with fittings RS or CI brackets, #@ mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750x20 mm

Providing and fixing sand cast iron/cast iron (spun) soil, waste and vent pipes. b)75 mm dia..

Providing and fixing sand cast iron heel rest sanitary bend.b) 75mm dia.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. b) 80x80x80 mm

Providing and fixing sand cast iron single equal plain junction of required degree.b) 80x80x80 mm

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vwnt arm complete including cost of cutting and making good the walls and floors.a) 100mm inlet and 100 mm outlet

(SH:- 3rd Floor)

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. 1 : 1.5 : 3 /1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement. 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in suspended floor,roofs, landings and balconies up to floor two level finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforced cement concrete work in stair case ( excluding landings) except spiral cases including finishing and plastering the exposed surface with cement mortar 1:3( 1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring , shuttering and reinforcement with M20 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete, cold twisted bars.

Centering and shuttering including strutting proppinf etc and removal of form work for: a) Foundation, footing,bases of columns etc and mass concrete

b) Wall ( any thickness) including attached plaster, buttresses plinth and string course.

c) Suspended floors, roofs landing shelves and their supported, balcony and chajjas

d) Stairs ( excluding landing) except spiral stair case.

Half brick masonry ( with best available local bricks) in cement mortar 1:3 ( 1 cement : 3 coarse sand) in foudation and plinth

Providing approved best available local wood ( Class - B II ) work in frames of doors, windows clerestory windowa and other frames wrought framed and fixed in postion

Providing and fixing panelled , glazed or panelled and glazzed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws.a) 40 mm thick best available local wood class - B I

Providing and fixing of two track slidind windows, concealed lock with natural colour aluminium, 5mm glass and necessary

Providing and fixing of anodised aluminium framed door with 2.5 inch x 1.5 inch chowkhat with 2 inch door frame and 12 mm thick are laminated particle board door closer door handle.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary screws etc complete

Providing and fixing aluminium slide door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing aluminium Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc. Complete. c)150x10 for window

Providing and fixing aluminam Handles anodised transparent or dyed to required or shade with necessary screws etc complete.a) 125 mm

Providing and fixing MS hooks and Eyes.a)300mm

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).

Providing and fixing 12 mm thick and 150 mm wide pelmet with 25 mm dia wooden curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.a) Timber class - A IV

Providing and fixing position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and raced with flat iron diagonals 20 mm x 5 mm size with top and botttom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during laying including painting the exposed portion of loop all as per standard design complete.

Providing and laying Vitrified tiles in different sizes( thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S 15633, of approved make, in all colours and shade laid on 20 mm thick cement mortar 1:3 including the joints with white cement and matching of matching pigment. b) size of tiles 600x600 mm

White glazed tiles 5mm, thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand ) painted with cement slurry.

20 mm cement plaster 1 : 3 ( 1 cement : 3 fine sand ) (in wall)

6 mm cemeent plaster to ceiling 1 : 3 ( 1 cement : 3 fine sand).

Appying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering ( two or more coats ) with oil bound washable distemper of approved brand manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats ) to give an even shade.

Providing and fixing PVC pipes with Brass Union A) 30cm lengtha) 15 mm nominal bore.

Providing and fixing Non Return Valve of approved quality a) 25 mm nominak bore.

Providing and fixing brass bib cock of approved quality.a) 15 mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm lenght. a)15mm nominal bore.

Providing and fixing PVC connection pipe with brass union 30 cm length.A) 30cm length a)20 mm nominal bore.

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet a) 100mm dia

b) 150 mm dia

Providing and filling sand all round GI pipes in external work.a) 20mm dia.

Providing and fixing white vitreous china water closet squating pan ( Indian type WC pan ) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern ( of approved make ) with fittings RS or CI brackets, #@ mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).a) 750x20 mm

Providing and fixing sand cast iron/cast iron (spun) soil, waste and vent pipes.b)75 mm dia..

Providing and fixing sand cast iron heel rest sanitary bend.b) 75mm dia.

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.b) 80x80x80 mm

Providing and fixing sand cast iron single equal plain junction of required degree.b) 80x80x80 mm

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vwnt arm complete including cost of cutting and making good the walls and floors.a) 100mm inlet and 100 mm outlet

SH: Septic Tank

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size bpulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc cosolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50 m.

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) foundation and plinth.

Providing and laying cement concrete 1 : 3 : 4 ( 1 cement : 3 coarse sand : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) foundation and plinth.

Providing and fixing upto floor five level precast cement concrete solid block including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centring, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1 cement: 3 fine sand ) on exposed surfaces complete.

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1:3 ( 1 cement : 3 fine sand ) of thickness not exceeding 6 mm to give a smooth and even exceeding 6 mm to give a smooth and even surfaces but excluding cost of reinforcement with 1:2:4 (1 cment :2 coarse sand: 4 stone shingle 20 mm nominal size)

Reinforced cement concrete in walls (any thickness ( including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1:3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smoothe and even surface excluding cost of centring,shuttering and reinforcement in : a) 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size.

12mm. Cement plaster 1:3 (1 cement : 3 fine sand) in walls.

Neat cement punning.

Making soak pit 2.50 m dia 3 m deep with 45x45cm dry brick honeycomb shaft and S W drain pipe 100 mm dia 1.80 m long complete as per standard design.

Reinforcement of RCC work including bending, binding and placing in position complete. A) cold twisted bars.

Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised - PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. a) single tree without door 110x110x110 mm

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. A) 100 mm dia.

Providing and fixing terminal guard: 100 mm (sand cast iron S&S as per IS - 3989)

Providing and laying cement concrete 1:5:10 ( 1 cement : 5 lime sand: 10 graded stone aggregate 40 mm nominal size) all around SW pipe including bed concrete 15 cm thick as per standard design. A)100mm dia SW pipes

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertation rubber washer 3 mm thick, bolts and nuts complete. A) 100 x 100 x 100 mm

Centring and shuttering including strutting, propping etc. And removal of form for:a) Foundation,footings, bases of columns etc. And mass concrete.

b)Suspended floors,roofs landings shelves and their supports, balconies and chajjas (3.5 m height).

c) Walls ( any thickness ) including attached pilasters, buttresses, plinth and string courses etc.

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement : 5 fine sand) RCC top slab with 1 : 2 : 4 mix ( 1 cement : coarse : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix ( 1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement and makinga)inside size 90 x 80 cm and 45 cm deep including CI cover with frame ( light duty ) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover 23 Kg and weight of frame 15 Kg)

SH: Electrification

Wiring for light point with 1.5 sq.mm FR PVC insulated copper conductor in single core cable in surface/recessed PVC conduit/casing capping, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required i)Short period

ii) Medium point

iii) Long point

Wiring for fan point/exhaust fan point with 1.5 sq mm FR PVC insulated copper in surface/recessed PVC conduit/casing capping, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the pointy with 1.5 sq,mm Fr PVC insulated copper conductor single core cable etc. as required.

ii) Medium point

iii) Long point

Wiring for circuit wiring with FR PVC insulated PVC sheathed multistrand copper conductor cable of size of 2x2.5 sq.mm in conceal PVC conduct along with 1 number 2.5 sq mm dia bare copper wire.

Wiring for power plug with 4x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recess PVC conduit alongwith 2 Nos. 4 sq. Mm. FR PVC insulatted copper conductor single core cable for loop earthing as required.

Supplying and fixing of angle holder i/c connection etc. As required.

Installation, testing and commisioning of pre wired, flourescent fitting all types complete with all accessories and tube etc. Firectly on ceiling/ wall, including connection with flexible wire and earthung etc. As required.

Installing,testing and coomisioning of ceiling fan i/c wiring the down rods of standard length (upto 30 cm ) with flexible wire etc. As required.

4'40 Watt fluorescent tube as required.

4'40 watt box type fluorescent tube fitting complete with all accessories such as acrylic cover, choke, starter etc, as required.

Electronic fan regulator

1 x 22 Watt CFL lamp with fitting

Ceiling rose as required

PVC tape, 25 mtr. Long.

Wooden Board of following sizesa) 8'' x 10 ''

2 x 10 sq. Mm PVC sheathed steel armoured PVC insulated aluminium conductor U.G. Cable as required.

Laying of 2 x 10 sq.mm PVC sheathed steel armoured PVC insulated aluminium conductor U.G cable direct i/c excavation of soil/earth, brick liming, refilling the trenches etc. As required.

4 way, SPN, single door, MCB DB as required

8 way, SPN, single door, MCB Db as required.

32/40 Amp. DP Isolator MCB as required.

6 Amp. 10 KA MCB as required.

1 Ph, Electronic Energy Meter ( 10-20A)

8 SWG GI wire

40 mm G.I ppipe as required

Extra for using salt and choke for G.I or copper plate with electrode as required.

SH: Storm Water Drain

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material) Ordinary soil, Manual Means, upto 3 m depth

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications RCC M20

Supplying, fitting and placing un-coated HYSD bar reinforcement in foundation complete as per drawing and technical specifications

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications

RCC Grade M20

Supplying, fitting and placing un-coated HYSD bar reinforcement in foundation complete as per drawing and technical specification

M/s Hita Enterprises