Construction of Lovleena Borgohain Multi Purpose Sports Complex (Mini Stadium) at Sarupothar Golaghat (Sarupothar LAC), Assam Under NIDA

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

PLINTH FILLING :Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

ANTI_TERMITE AND DPC : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

RCC Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

RCC Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. [for Basin / Urinal / Sink waste] 40 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. [for Basin / Urinal / Sink waste] 50 mm dia

Supplying, Fixing of C.P. brass twin coat hook.Make : Jaquar Cat no. CAN-1161N or Hindware & Kohler.

Supplying, Fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects. Health faucet -Make : Jaquar Cat no. ALD-565 or Hindware & Kohler.

Supplying, Fixing C.P. 2 IN 1 Bib cock Jaquar Cat no. CON-041KN , Hindware & Kohler.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing soil, waste pipes : Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 100 mm dia

Providing and fixing soil, waste pipes : Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 75 mm diameter : vent pipes :

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron / cast iron (spun) pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc. For 100mm diametre

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron / cast iron (spun) pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc. For 75mm diametre

Providing and Fixing shielded coupling for Hubless centrifugally cast iron pipe. 100 mm SS 304 grade coupling with EPDM Rubber gasket.

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 100 mm dia

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 75 mm dia

Providing and fixing plain bend of required degree. 100 mm dia

Providing and fixing plain bend of required degree. 75 mm dia

Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm

Providing and fixing double equal plain junction of required degree. 75x75x75x75 mm

Providing and fixing single equal plain junction of required degree : 100x100x100 mm

Providing and fixing single equal plain junction of required degree : 75x75x75 mm

Providing and fixing double unequal plain junction of required degree : 100x100x75x75 mm

Providing and fixing double unequal plain junction of required degree : 100x100x75 mm

Providing and fixing double equal plain invert branch of required degree: 100x100x100x100 mm

Providing and fixing single equal plain invert branch of required degree : 100x100x100 mm

Providing and fixing single unequal plain invert branch of required degree : 100x100x75 mm

Providing and fixingHubless centrifugally cast (spun) iron terminal guard (slotted cowl) -100 mm dia as per IS 15905

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Cutting chases in brick masonry walls for following diameter sand cast iron / centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.50 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand). 100 mm

Cutting chases in brick masonry walls for following diameter sand cast iron / centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.50 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand). 75 mm

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff, etc., over a coat of primer (of approved quality) for new work. 100mm diametre pipe

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff, etc., over a coat of primer (of approved quality) for new work. 75mm diametre pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(Concealed Work) 40 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm nominal outer dia Pipes

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 40 mm diameter pipe

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : 50 mm diameter pipe

Providing and fixing brass bib cock of approved quality. 15 mm nominal bore

Providing and fixing brass bib cock of approved quality. 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end). 32 mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end). 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end). 50 mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end). 65 mm nominal bore

Providing and fixing ball valves (brass) of approved quality, High or Low pressure with plastic floats complete. 20 mm nominal bore

Providing and fixing ball valves (brass) of approved quality, High or Low pressure with plastic floats complete. 25 mm nominal bore

Cutting holes up to 15 x 15 cm in R.C.C floors and roofs for passing pipes etc. and repairing the holes after insertion of pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggeragate 20 mm nominal size) including finishing complete so as to make it leak proof.

Making holes up to 20 x 20 cm and embedding pipes up to 150 mm dia in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggeragate 20 mm nominal size) including dispoal of malba.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing, laying and jointing single wall corrougated PVC lateral drain pipe with perforation and synthetic filter confirming IS 9217-2004 including testing of joints etc. complete . (Astral Geo-Rex) for ground water dewatering. 100 mm

Providing, laying and jointing single wall corrougated PVC lateral drain pipe with perforation and synthetic filter confirming IS 9217-2004 including testing of joints etc. complete . (Astral Geo-Rex) for ground water dewatering. 65 mm

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 160 mm

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 250 mm

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W pipe including bed concrete as per standard design. 150 mm Diameter S.W Pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W pipe including bed concrete as per standard design. 200 mm Diameter S.W Pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and inside plasreting 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal dimeter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Extra for depth of manholes Size 90x80 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Extra for depth of manholes Size 120x90 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality M D - 10 Circular shape 500 mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineerin- charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia having minimum wall thickness 5.00 mm

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality M D - 10 Circular shape 500 mm internal diameter

Hydropneumatic System for OHT Tank Filling Supply, installation & commissioning of 2 Nos. Vertical Multi Stage Centrifugal Pump for Clear Water with 50Hz, 380-415V, 2 Pole IE3 efficiency class motor (As per IEC standard). Pump shall be CI with CED quoted- Suction & Discharge Casing, SS 316 -Shaft and all other components will be with SS 304, Mechanical Seal (SiC vs SiC face) . Pump should have minimum 70% efficiency. Pump controller suitable for 2 Pumps (1W+1S) with LCD screen displays, phase loss protection (incoiming as well as for outgoing), Individual pump overload protection, individual pump under voltage protection, dryrunning protection without installing any float switch, memory function when power off and during recovery, visual and audio alarm for fault prompt, auto manual switch, and pump should operate based on the sump water level and both pump should run together for high level. Panel should come with 3 Nos Float switch to work as per the sump water level. Flow Rate-15 m3/hr (1W+1S) Head-15m

Submersible Borewell Pump Supply installation & Commissioning of submersible borewell pump with SS 304-Casing/Impeller/Shaft & Mechanical seal coupled with a 380-415V, 50Hz 2 Pole, Insulation Class-F, IP 68 Protected Rewindable Electric Motor (Motor Make-.TESLA/FRANKLIN) Pump controller suitable for 1 Pump with LCD screen displays, phase loss protection (incoiming as well as for outgoing), Individual pump overload protection, individual pump under voltage protection, dryrunning protection without installing any float switch, memory function when power off and during recovery, visual and audio alarm for fault prompt, auto manual switch, and pump should operate based on the UGT water level. Panel should come with 1 No. Float switch to work as per the sump water level. Flow Rate Per Pump-11.5 m3/hr (1 No.) Head-30m

SITC of 35W, Post Top LED with aluminium housing, UV resistant powder coated black finish, lumen ≥ 3325 lumens ,.i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required..Wipro Make LED (LP07),CAT No. LP07-431-XXX-57-CL or equivalent approved make

SITC of 35W, Gate light, LED with aluminium housing,minimum 90 lm/W. CRI-80, IP66, i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Make Post Top LED (LP06),CAT No. LP06-351-XXX-57-XX or equivalent approved make

SITC 7W,Bollard, LED, extruded Aluminium housing,6500K, lumen ≥ 402 lumens (57 lm/W).i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Make Bollard LED (LB12),CAT No. LB12-880-XXX-65-08 or equivalent approved make

SITC of 18W LED Surface mounted outdoor type IP65 Down light fixture,die cast Aluminium housing. 6000 K ,i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Outdoor Downlight (LD52),CAT No. LD52-301-040-060-XX or equivalent approved make

Supplying & Erection of hot dipped galvanized 16.0 Meter Octagonal GI Highmast suitable for 8 Nos. Floodlight luminaire. Bottom section thickness of 4mm and top section thickness of 3 mm. PCD of 445 mm along with 6 Nos. foundation bolts. Foundation bolt dimension of M30X850. Base plate dimension of 520mmX25mm ,Wipro Make or equivalent approved make

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Supplying of following size AL conductor armoured XLPE insulated PVC sheathed power cable of 1.1 KV grade ISI marked IS:7098(Part 1) 1988 with ammendment upto date as per following manner etc as required 2Cx10 sq.mm AL XLPE Armoured Cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 2Cx10 sq.MM. AL XLPE Armoured

Supplying & Erection of hot dipped galvanized 4.0 Meter Octagonal GI pole with top dia of 70mm, bottom dia 130 mm, PCD of 225 mm and Sheet thickness of 3mm.base plate dimension of 200mmX200mmX12mm, GI base plate,Wipro Make or equivalent approved make

Supply of SMD 200W LED Floodlight fixture, 100 lm/W (20000 lumens), die cast Aluminium housing with PC lens and toughened glass diffuser.i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. Wipro Make Alpha LED (LF20,) CAT No. LF20-272-060-57-G2 or equivalent approved make ( for 16Mtr. High mast)

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm), Double run

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.( provide 3 meter GI pipe

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Supply of following sizes of XLPE insulated PVC sheathed aluminium/copper conductor armoured cable of 1.1 KV grade on existing cable tray / surface including saddle, clamps etc. complete as required. Conforming IS 7098(Part 1) 1988 3.5Cx70 sq.mm AL. XLPE ARMOURED CABLE

Supply of following sizes of XLPE insulated PVC sheathed aluminium/copper conductor armoured cable of 1.1 KV grade on existing cable tray / surface including saddle, clamps etc. complete as required. Conforming IS 7098(Part 1) 1988 4Cx16 sq.mm AL. XLPE ARMOURED CABLE

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 3.5Cx70 sq.mm AL. XLPE ARMOURED CABLE

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 4C X16 SQ. MM. AL XLPE Armoured

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 35 sq. mm and upto 95 sq. mm

Supply, installation, testing and commissioning of silent type water cooled DG set conforming to latest environment protection regulations for emission and noise level comprising of radiator (CPCB II compliant with latest amendments), power pack, electronic governor, vertical multi-cylinder diesel engine equipped with flywheel having Prime Power Rating of 62.5 KVA, 415 Volts at 1500 RPM, 0.8 lagging power factor at 415 volt suitable for 50 Hz, 3 phase system & for 0.8 Load Factor and consisting of the followings: Diesel Engine: Full electronic authority diesel engine 4 stroke radiator water cooled, electric start with electronic fuel injection system of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50%RH & at 218.23 m MSL and conforming to BS:5514, BS:649, IS:10000, capable of taking 80% block load at the start and 10% over loading for one hour after 12 hours of continuous operation. The engine shall be fitted complete with all the required accessories. Engine mounted instrument Panel fitted with digital display for following:

Supplying and making cement concrete foundation 1:2:4 (1 cement, 2 coarse sand, 4 graded stone aggregate of 40 mm nominal size) i/c excavation, sand cushioning at the bottom and on all sides in accordance with manufacturers design i/c providing angle iron of size 35 x 35 x 5 mm thick on all the corners of foundation or as reqd. (DG Foundation)

SITC of exhaust gas piping of suitable dia. Welded black MS B Class pipe conforming to IS:3589 cut to required lengths and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with mineral wool/Rockwool, 50 mm thick wiremesh & aluminium cladding etc. as required as per specification

Supply,insallation, testing and commissioning of 1 no. 63KVA, DYN11, 11000/415V, 50HZ, 3ph, Star rated, IS1180 level-2, Indoor type oil filled transformer, Copper winding having continuous rating of 63 KVA,The transformer shall have bottom entry cable end box on HV side for 3 x 300 sq.mm. XLPE cable and suitable flange (for vertical takeoff). The LV Box of transformer shall be suitable for terminating aluminum, Armoured, cable with all fitting and accessories complete as required, as per Specification, Technical Data sheet & latest IS as per Specification, Technical Data sheet & latest IS : IS 2026 (Part 1 to Part 5): with latest revisions Rating: 63 KVA Service : OUTDOOR Cooling: ONAN. No load voltage ratio: 11KV/415V. Frequency: 50Hz. Vector group: Dy11. Type: Oil type Tapping: +5% to -15% @ 1.25%, 16 Steps / 17 Positions, Fittings & accessories SITC of 63 KVA, 11/0.415 KV Oil Type Transformer as per above specification

Supply of 11 KV, 3C x 95sq.mm. XLPE (UE) armoured cable. Conforming IS 7098(Part II) 1988

PSC pole erection for HT OH supply line Providing of 8 Mtrs. Long, 200 Kgs. PSC Pole. Detail Specification and Standards shall be as per technical sprcification.

Erection of PSC Pole of 8 Mtr. Length in brick ballast and ramming the foundation, finishing with 150 mm thick cement concrete (1:3:6) layer on top with including excavation and refilling etc. as required. Detail Specification and Standards shall be as per technical sprcification.

Providing & Erection of Stay set complete (Galvanized) with 19/20 mm dia x 1.8 Mtr. Long Stay Rod, Anchor Plate of size 45 Cm. X 45 Cm. X 7.5 mm thimble, stay clamps, turn buckle (20 mm x 60 mm), 7/3.15 mm dia G.I. Stay Wire and strain insulator etc. in cement concrete 1:3:6 foundation including excavation and refilling etc. as required. Detail Specification and Standards shall be as per technical sprcification.

Providing & Erection of metallic vitrified danger notice board, to be erected as per IS. Detail Specification and Standards shall be as per technical sprcification.

Providing and Erection of Barbed wire on PSC Pole. Detail Specification and Standards shall be as per technical sprcification.

Providing and Erection of 11 KV Pin Insulator with Hardware. Detail Specification and Standards shall be as per technical sprcification.

Providing & Erection of MS Channel 75 x 40 x 6mm, 4 feet long complete with 50 x 6 flat iron clamps, bolts, nuts and washers drilling holes for cut point. Detail Specification and Standards shall be as per technical sprcification.

Providing and Erection of coil type earthing with 6 SWG GI earth wire with charcoal and salt from top of pole as per IE rules. Detail Specification and Standards shall be as per technical sprcification.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. : Upto 120 sq. mm.

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 120 sq. mm

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing first aid box as approved by St. John Ambulence Brigade/ Indian Red Cross confirming to IS 2217:1963

Supply and fixing of First Aid Chart in 5 mm glassed wooden frame ( approx front area 1.20 sqmt)

Supplying Fire buckets with round bottom made of GI sheet,24 SWG ,9.5 liters capacity painted inside white and outside red with a word FIRE on the face of the bucket stand to hang buckets made out of MS Angle iron frame work of size 40 X 40 X 6 mm

Supply and fixing Rubber mats of AC Voltage proof upto 3.3 kV grade 1.0 Mtrs x 0.9 Mtrs X 12mm or required thickness as required by the Electrical Inspectorate and confirming to IS 5424

Supply and fixing of Electric Shock treatment chart mounted on 5mm Glass wooden frame , Size - 50 x 70 cm, Rectangle including fixing on wall ( approx front area 1.20 sqmt)

Supply and fixing of Safety Instruction chart mounted on 5mm Glass wooden frame, Size - 50 x 70 cm, Rectangle including fixing on wall ( approx front area 1.20 sqmt)

Supply of Crompton/Nezone make Stadium Mast 30 Mtr Hight + 5 mtr Boom suitable for 30 LED stadium Flood Light fittings

Supply of foundation bolts

Supply of Man Rider (common for 4 masts) suitable for 150kg carring capacity

Supply of Crompton make 960 watt, system efficacy 130 Lumen/Watt with 10 Degree Beam Angle, LED energy saving, long lasting Sports light with exclusive & innovative aluminium die cast body, high performance electronic drivers & photobiologically safe Flood Light (20 Nos Per Mast) Crompton Model No: CFS-502-960-57-10D-HL2-GL-NSR or equivalent

Supply of Crompton make 960 watt, system efficacy 130 Lumen/Watt with 30 Degree Beam Angle, LED energy saving, long lasting Sports light with exclusive & innovative aluminium die cast body, high performance electronic drivers & photobiologically safe Flood Light (10 Nos Per Mast) Crompton Model No: CFS-502-960-57-30D-HL2-GL-NSR or equivalent

Supply of Crompton make 12 watt, system efficacy 100 Lumen/Watt, LED energy saving, long lasting downlighter with robust PDC Aluminum body, high performance low-height back lit suitable for any modern professional work space, Crompton Model No: CDR-205-12-57-SL-NWH or equivalent

Supply of Crompton make 40 watt, system efficacy 100 Lumen/Watt, LED energy saving, long lasting weatherproof integrated LED Batten suitable for industrial application Crompton Model No: CIS-300-40-57-SL-DP-NGR or equivalent

Supply of Crompton make 36 watt, system efficacy 100 Lumen/Watt, LED energy saving, long lasting Recessed full lit glare free uniform illumination 2X2 LED Panel Light , Crompton Model No: LCTLRNE-36-FO-CDL or equivalent

Supply of Main Panelmade out with 2mm CRCA sheet steel, 3 phase,suitable for floor mounted,user front facia,powder coated,cubical type,suitable cable. entry.provision and including all necessary electrical protections,aluminium Bus bar etc. The panel shall be of requisite rating of all components & adequate capacity to handle load as per lighting design standards envisaged

Supply of Distribution feeder Pillar made out with 2mm CRCA sheet steel, 3 phase,suitable for floor mounted,user front facia,powder coated,cubical type,suitable cable entry provision and including all necessary electrical protections,aluminium Bus bar etc. The panel shall of requsite rating of all components & adequate capacity as per lighting design envisaged

Supply of 150 KVA Liquid-Cooled Three Phase STD panel KOEL Green Silent D.G. Set comprises of KOEL Green Engine at 1500rpm complying with the requirement of BS5514/IS10002, directly coupled to a KOEL Green AC generator capable of 50Hz 0.8 PF(lag) generally meeting the requirements of BS5000 at 230/415 Volt. A power control panel to regulate the AC power is also provided.

Supply of cable for wiring of luminaire 2.5 Sqmm copper round flexible (40 meter per light fitting X 30 fittings X 4 masts ) total 5000 Meters. (each roll containing 200mtrs)

Supply of cable for wiring of luminaire 1.5 Sqmm copper round flexible (50 meter per light fitting X 486 fittings ) total 5000 Meters. (each roll containing 200mtrs)

Supply of Aviation Obstruction Light LED (2 Per Mast)

Miscellenous Electrical items like, MCB, Lugs, Glands, Cable Tie etc etc

Construction of shallow foundation with 1:2:4 concrete of the High Mast considering safe Soil bearing capcity at site as 10T/SQ mtr at suitable depth as per Civil foundation diagram

Erection of High Mast with the help of suitable eqipments & wiring of lumanaires. 30 Ton capacity Hydra/Crane with minimum boom length of 25 mtr shall be provided by customer

Provision of GI Pipe Earthing with 3 mtr long 65 mm GI pipe with 25 X 3 mm GI flats ( 2 nos per mast required 1 for Panel 1 for mast) alongwith back filling with Salt, Charcoal etc.

Erection , Installation & Commissioning of feeder panel on suitable foundation

Commission of point wiring

Aiming Charges.( Final allingments/adjustment/optmisation of lighting & lux level measurement)

Supply of Aluminum Armoured LT cable size 120 Sqmm 3.5 core ( for connecting power source/transformer to Main feeder panel Havells make

Supply of Aluminum Armoured LT cable size 50 Sqmm 3.5 core (for connecting Main feeder panel to Distrbution Feeder panels)Havells make

Cable Laying with cushioning escavation at 75 cm depth for 120 sqmm 4 core aluminium armoured LT cable

Cable Laying with cushioning escavation at 75 cm depth for 50 sqmm 4 core aluminium armoured LT cable.

APDCL Load Security for 120 KW and Shifting of pole as directed by the Site Engineer

Rantu Boruah