CERTAIN REPAIRS TO INTERLOCKING TILE RETAINING WALLS DRAINS FENCING AND GATE AT SECT D UNDER GE 865 EWS

Amount

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level and removing demolished material out of Military station.

Demolition of cement concrete in any description and any position not otherwise specifically provided for.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), all as specified and as directed

Dismantling chain link fencing/expanded metal or mesh not exceeding 4kg/Sqm fixed in steel, wood fillets, concrete post etc. of any description.

Dismantling posts or struts (wood , steel or RCC) any section , including taking out embedded portion in concrete and making good disturbed ground

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbs, aprons, etc laid dry of laid dry and pointed.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed

Demolition of stone /boulder masonry built in cement mortar including all quoins, arches , pillars etc and removing demolised material out of Military station all as specified and as directed

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:6 all as Specified

All as per ser item No 11 above but except blocks.

M&L random rubble stone masonary well bonded bedded solidily hearted in CM 1:6.

All as per ser item No 13 above but except stones.

M&L for 10mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed

Raised pointing to random or polygonal rubble, uncoursed block walling in CM 1:4 complete all as specified and as directed.

M&L for preperation of new plastered wall surface of any description and applying two coat of cement based paint over a coat of chalk whitening complete all as specified and as directed.

M&L for Cement concrete 1:5:10 type E-2, (40mm graded aggreate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc.

M&L machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to IS 15658-2006 of 60mm thickiness M-35 grade over and including 50mm thick (avg) sand cushioning including watering, ramming and rolling complete all as specified and as directed by Engr-in-Charge.

M&L for Cement concrete 1:4:8 type B-2, (40mm graded aggreate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:4) and all as directed by Engr-in - charge.

M&l for PCC type D-2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation all as specfed and drected.

M&L dressed granite or trap / Precast cement concrete 1:2:4 type B1 (20 mm nominal size of graded course aggregate) Kerb stones roughly squared stones of size 20cm x 30 cm ,so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck finish ( rate included for removal of old damaged curb stones of any description).

M&L for preperation of new surface on Brick,Concrete,Wall and Stone surface of any description descripton and applying two coat of synthetic enamal paint over a coat of primer complete all as specified and as directed.

S& F mild steel Hand rails, half round or other steel section or core for wooden hand rail straight portion , drilled and countersunk for balusters running bas for doors , balusters, nosing to steps including embedding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed including all necessary drilling bolting or riveting etc and similar work conforming to Fe 290 Gd E 165

M&L for PCC type D-2, (1:3:6) , using 40mm graded crushed stone aggregate as in lean conc , sub base ,or mass conc , foundation filling etc.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards,rails, straining bolts,etc.including provision of binding wire.

Supply only chain link MS galvanised fencing of 100 x 100mm opening size as directed by Engr-in-charge.

Mild steel TMT bars10mm dia and over (for tie bar of chain link fencing), cut length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips .

S&F Mild steel steel bolts exc 12 n exc 20 mm dia of neck purpose made with hexagonal or square head one ned and screwed the other or screwed both ends to be fitted with washer and one hexagonal square nut.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes or induction butt welded tubes conforming to IS 1161-1979 Grade St-240

Prividing and fixing Aluminium Composite Panels in all coloursof approved brand for external /internal wall/column cladding at all heightsand elevations including necessary aluminium composite panels consisting of 3mm thermoplastic core of anti oxide LDPE sandwitched between two skins of 0.5 mm thick alloy sheetmaking a total sheet thickness of 4mm. The surface shall be finished with PDVF base coating on the top side and service coating on the reverse side shall be with polymer paint. Coating shall confirm to ECCA of AAMA. The system shall be designed to withgstand wind pressure of 200 Kg/Sqm and shall be fixed to the brick/stone/masonry /RCCwalls/MS framed structure with necessary clamps , bracket and anchor fasteners. All clamps and brackets shall be hot dip galvanised min 80micron thick and conforming to IS : 4759-1996. The extruded alluminium section shall be anodised in napproved colour with anodic coating min 20microns. Extruded sections shall be of 6063 T5 or T6 alloy conforming to ASTM B-221 (items include cost of Aluminiumframe of size (Min 50 x 25mm), ACP panels, Clamps 110mm size, weather sealent , gasket , foam, fixtures, scaffoldings, all machineries and other fastening streps, nut /bolt, rivets washersetc complete all as directed. Make : ALUPEX/ALUDECOR/ ALSTRONG. Note : The work is to be carried out at height of 6 to 8 metre.

M&L cement concrete 1:3:6 type C2 (40mm graded aggregate) in Surface channels and drains all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.

Extra for forming fair finished drain or channel 55cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.

M&L for precast cement concrete Type C1, 1:3:6 (20mm graded aggregate) in lindings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and as directed.

M&L for PCC type B1 (1:2:4) using 20 mm graded crushed aggregate in coping ,mass concrete.

neelam construction co

Mehar Enterprises

M/s Koul & Sons

M/s Aman Enterprises

M/s. Gee Gee Enterprises

M/S AMCO INDUSTRIES AND EXPORT CORPORATION

JP AND CO.

M/S MALIK CHAND SIRI RAM