Loading
Loading…
Loading…
Tender Value
₹27.3 Cr
EMD Value
₹15.2 L
Closing Date
23 Jan 2026, 3:00 pmClosed
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
TENDER
14 conditions · 3 needing a document upload
Financial Eligibility Criteria (Para-10.2 (Pt-I) of GCC April 2022): The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in Crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, O R (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, OR (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Erection, testing, commissioning of 132 KV and above voltage transmission line work & Erection, testing, commissioning Modification of at least one Bay of 132 KV and above voltage at GSS end.
1 condition
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Design, Supply, erection, testing & Commissioning of Bays at Bodh Gaya GSS with termination 132 KV D/C transmission line in between Gaya TSS to Bodh Gaya BSPTCL GSS through 132 KV underground Cabling under Railway Project Danapur of East Central Railway.
RPDNRHSTRLGAYARETENDER-3~ECR
RPDNRHSTRLGAYARETENDER-3
Open
Works - General
9 Months
Patna, Bihar
₹0
₹15.2 L
23 Jan 2026
22 Dec 2025
2 Jan 2026
454 items across 3 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 20,41,81,312.4 | ||
| — | — | — | 26,64,162.34 | ||
| Supply of 145KV, 2000A,40KA , TP,Circuit breakers with operating mechanism and marshalling box and associated structures etc. | — | 2.00 | — | — | |
| — | — | — | 48,438.1 | ||
| Erection,testing and commissioning of 145KV,2000A,40KA,TP,Circuit breakers with operating mechanism and marshalling box and associated structures etc. | — | 2.00 | — | — | |
| — | — | — | 23,51,902.56 | ||
| Supply of 145KV, 800-400-200/1A,40KA,5core current transformer single phase with terminal connectors etc. | — | 6.00 | — | — | |
| — | — | — | 45,405.96 | ||
| Erection, testing and commissioning of 145KV,800-400-200/1A,40KA,5 core current transformer single phase with terminal connectors etc. | — | 6.00 | — | — | |
| — | — | — | 5,59,636.9 | ||
| Supply of 145KV,3core,potential transformer, single phase with marshalling boxes for a set of 3 PTs with terminal connector etc. | — | 2.00 | — | — | |
| — | — | — | 27,531.7 | ||
| Erection, testing and commissioning of 145KV,3 core, Potential transformer , single phase with marshalling boxes for a set of 3 PTs with terminal connector etc. | — | 2.00 | — | — | |
| — | — | — | 5,11,777.86 | ||
| Supply of 120KV, 10KA, class-3 Gapless lightning arrestor with discharge counters and terminal connector etc, single phase. | — | 6.00 | — | — | |
| — | — | — | 74,664.12 | ||
| Erection, testing and commissioning of 120KV, 10KA, class-3 Gapless lightning arrestor with discharge counters and terminal connector etc, single phase. | — | 6.00 | — | — | |
| — | — | — | 2,72,306.52 | ||
| Supply of 145KV solid core post insulator. | — | 12.00 | — | — | |
| — | — | — | 21,807.36 | ||
| Erection,testing and commissioning of 145KV solid core post insulator. | — | 12.00 | — | — | |
| — | — | — | 11,30,844.7 | ||
| Supply of 145Kv,1250A,31.5KA,TP,Standard gang operated HCB isolator with operating mechanism box, support structure and terminal connectors, insulators including suitable interlocking arrangement etc with 1 E/S. | — | 2.00 | — | — | |
| — | — | — | 38,717.74 | ||
| Erection, testing and commissioning of 145Kv,1250A,31.5KA,TP,Standard gang operated HCB isolator with operating mechanism box, support structure and terminal connectors, insulators including suitable interlocking arrangement etc with 1 E/S. | — | 2.00 | — | — | |
| — | — | — | 10,31,189.96 | ||
| Supply of 145Kv,1250A,31.5KA,TP,Standard gang operated HCB isolator with operating mechanism box, support structure and terminal connectors, insulators including suitable interlocking arrangement etc without E/S. | — | 2.00 | — | — | |
| — | — | — | 35,951.8 | ||
| Erection, testing and commissioning of 145Kv,1250A,31.5KA,TP,Standard gang operated HCB isolator with operating mechanism box, support structure and terminal connectors, insulators including suitable interlocking arrangement etc without E/S. | — | 2.00 | — | — | |
| — | — | — | 12,967.2 | ||
| Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | — | 6.00 | — | — | |
| — | — | — | 1,00,111.52 | ||
| Supply of 145KV CT jn Boxes. | — | 2.00 | — | — | |
| — | — | — | 3,026.7 | ||
| Erection,testing and commissioning of 145Kv CT jn Boxes. | — | 2.00 | — | — | |
| — | — | — | 2,06,420.28 | ||
| Supply of 132 KV single tension string insulator assembly with 10 nos. antifog type disc insulator with all hardwares accessories including arcing horn and tension clamp set suitable for single ACSR Zebra conductor with trunbuckle:- | — | 12.00 | — | — | |
| — | — | — | 17,469.6 | ||
| Erection, testing and commissioning of single tension string insulator assembly with 10 nos. antifog type disc insulator with all hardwares accessories including arcing horn and tension clamp set suitable for single ACSR Zebra conductor with turnbuckle:- | — | 12.00 | — | — | |
| — | — | — | 2,02,341.48 | ||
| Supply of 132 KV single tension string insulator assembly with 10 nos. antifog type disc insulator with all hardwares accessories including arcing horn and tension clamp set suitable for single ACSR Zebra conductor without trunbuckle:- | — | 12.00 | — | — | |
| — | — | — | 17,469.6 | ||
| Erection, testing and commissioning of 132 KV single tension string insulator assembly with 10 nos. antifog type disc insulator with all hardwares accessories including arcing horn and tension clamp set suitable for single ACSR Zebra conductor without trunbuckle:- | — | 12.00 | — | — | |
| — | — | — | 23,828.5 | ||
| Supply of ACSR Zebra conductor. | — | 50.00 | — | — | |
| — | — | — | 5,395 | ||
| Erection, testing and commissioning of ACSR Zebra conductor. | — | 500.00 | — | — | |
| — | — | — | 38,424.6 | ||
| Supply of 132 KV system TEE to suit Zebra ACSR conductor all both ways. (RI-11040) | — | 12.00 | — | — | |
| — | — | — | 345.24 | ||
| Erection, testing and commissioning of 132 KV system TEE to suit Zebra ACSR conductor all both ways. (RI-11040) | — | 12.00 | — | — | |
| — | — | — | 16,056 | ||
| Supply of rigid connector on support insulator to suit Zebra (28.58 dia) ACSR conductor. (RI- 11050) | — | 12.00 | — | — | |
| — | — | — | 345.24 | ||
| Erection, testing and commissioning of rigid connector on support insulator to suit Zebra (28.58 dia) ACSR conductor. (RI- 11050) | — | 12.00 | — | — | |
| — | — | — | 89,208 | ||
| Supply & Erection of bimetallic connector for ACSR Zebra conductor RI- 11030 | — | 60.00 | — | — | |
| — | — | — | 24,558.72 | ||
| Supply of PG clamp suitable for ACSR Zebra to Zebra. | — | 24.00 | — | — | |
| — | — | — | 25,063.68 | ||
| Erection, testing and commissioning of PG clamp suitable for ACSR Zebra to Zebra. | — | 24.00 | — | — | |
| — | — | — | 3,057.2 | ||
| Supply of cleat type clamps for 75x12mm GI flat. | — | 20.00 | — | — | |
| — | — | — | 8,776 | ||
| Erection, testing and commissioning of cleat type clamps for 75x12mm GI flat. | — | 20.00 | — | — | |
| — | — | — | 1,78,400 | ||
| Supply of Grounding conductor 75mmx 12mm GS flat for equipment and structure earthing. | — | 200.00 | — | — | |
| — | — | — | 87,760 | ||
| Erection, testing and commissioning of Grounding conductor 75mmx 12mm GS flat for equipment and structure earthing. | — | 200.00 | — | — | |
| — | — | — | 38,907.5 | ||
| Supply & erection of 50X6 MS flat for earthing. | — | 250.00 | — | — | |
| — | — | — | 91,66,070.08 | ||
| Supply of Control & Relay Pannels With auto reclose for transmission line | — | 2.00 | — | — | |
| — | — | — | 1,09,571.26 | ||
| Erection, testing & commissoning of Control & Relay Pannels With auto reclose for transmission line | — | 2.00 | — | — | |
| — | — | — | 69,323.82 | ||
| Supply of 1.1 KV grade power and control cables of size -2cx6mm2 AL PVC. | — | 0.50 | — | — | |
| — | — | — | 5,86,580.52 | ||
| Supply of 1.1 KV grade power and control cables of size -10c x 2.5mm2 CU PVC. | — | 2.00 | — | — | |
| — | — | — | 95,831.59 | ||
| Supply of 1.1 KV grade power and control cables of size -2c x 4 mm2 CU PVC. | — | 1.00 | — | — | |
| — | — | — | 2,01,200.49 | ||
| Supply of 1.1 KV grade power and control cables of size -4c x 4 mm2 CU PVC. | — | 1.00 | — | — | |
| — | — | — | 5,48,091.62 | ||
| Supply of 1.1 KV grade power and control cables of size -27c x 2.5 mm2 CU PVC. | — | 0.50 | — | — | |
| — | — | — | 3,68,283.54 | ||
| Supply of 1.1 KV grade power and control cables of size -19c x 2.5 mm2 CU PVC. | — | 0.50 | — | — | |
| — | — | — | 6,14,165.82 | ||
| Supply of 1.1 KV grade power and control cables of size -14c x 2.5 mm2 CU PVC. | — | 0.90 | — | — | |
| — | — | — | 63,536.53 | ||
| Laying,erection, termination,testing and commissioning of 1.1 KV grade power and control cables size-, 2C x6mm2, 10c x 2.5 mm2 CU PVC, 2Cx4 mm2 CU PVC & 4cx 4 mm2 CU PVC. | — | 4.50 | — | — | |
| — | — | — | 11,643.74 | ||
| Laying,erection, termination,testing and commissioning of 1.1 KV grade power and control cables size-27cx 2.5mm2 CU PVC | — | 0.50 | — | — | |
| — | — | — | 22,704.71 | ||
| Laying,erection, termination,testing and commissioning of 1.1 KV grade power and control cables size- 19c x 2.5 mm2, 14c x 2.5 mm2 CU PVC | — | 1.30 | — | — | |
| — | — | — | 7,80,504 | ||
| Supply & Erection Cable trench & cover. | — | 400.00 | — | — | |
| — | — | — | 18,618.67 | ||
| Preparation of Design and Drawing and including check survey | — | 1.00 | — | — | |
| — | — | — | 61,521 | ||
| Earth work in excavation & back filling in fdn. Trenches, drains etc. including dressing of sides & ramming of bottoms, lift upto 3.0 m, including pit marking, dewatering, getting out the excavated soil & disposal of surplus excavated soils as directed within a lead of 50 m complete as per specifications, drawing & instruction of Engineer-in - Charge/Normal dry soil | — | 300.00 | — | — | |
| — | — | — | 67,422 | ||
| "Wet soil/Partially sub merged/Fully sub merged" | — | 300.00 | — | — | |
| — | — | — | 31,16,452 | ||
| "Providing & laying in position Reinforced Cement concrete work in pyramid & chimney, stepped foundation of tower foundation & plinth, with coarse sand & 20 mm. & down stone aggregates of approved quality,well graded, washed and screened including cost of supply & transport of all materials to site, mixing, laying, vibrating, curing etc. complete & also including erection, providing muffboxes / formwork, supporting, striking out, cleaning etc. of muff-boxes, but excluding the cost of reinforcement as per drgs., specifications & directions with Concrete mix 1: 1 : 2" | — | 400.00 | — | — | |
| — | — | — | 65,842.8 | ||
| Providing & laying in position plain cement concrete in foundation & plinth with coarse sand & 20 mm. & down stone aggregates of approved quality, well graded, washed and screened including cost of supply & transport of all materials to site., mixing, laying, vibrating, curing etc. complete but excluding centering & shuttering as per drawings, specification & direction with/ Mix 1 :3 :6 (M-10) | — | 20.00 | — | — | |
| — | — | — | 1,07,253.2 | ||
| Mix 1 :2 :4 (M-15) | — | 20.00 | — | — | |
| — | — | — | 78,71,500 | ||
| Reinforcement | — | 175000.00 | — | — | |
| — | — | — | 4,84,408.3 | ||
| Design, fabrication & Supply of A,B,C,D type tower, special structure including special towers for crossing, gantry structure & 12M/+ 18 M extension. Super structure and Stubs and Substation gantry. | — | 5.00 | — | — | |
| — | — | — | 75,460.8 | ||
| Erection of A, B, C, D type tower, special structure including special towers for crossing, gantry structure & 12M/+ 18M extension. Super structure and Stubs and Substation gantry. | — | 40.00 | — | — | |
| — | — | — | 1,45,708.5 | ||
| Supply & erection of earth electrode with earth pit box . Including writing earth value on protective box as per RDSO DRG no. ETI/OHE/P/7020(8/84) or latest . | — | 50.00 | — | — | |
| — | — | — | 1,459.92 | ||
| Supply & Erection Number Plate | — | 8.00 | — | — | |
| — | — | — | 1,944.4 | ||
| Supply & Erection Phase Plate (set of 3) | — | 8.00 | — | — | |
| — | — | — | 2,314 | ||
| Supply & Erection Circuit Plate (set of 2) | — | 8.00 | — | — | |
| — | — | — | 64,992.24 | ||
| Barbed Wire for Anticlimbing Device | — | 0.50 | — | — | |
| — | — | — | 31,691.76 | ||
| "Providing Anticlimbing Device excluding barbed wire, bolt, nut, washers (galvanised and assorted) (a)to fit different 132 KV tower" | — | 8.00 | — | — | |
| — | — | — | 5,28,68,429.35 | ||
| Supply of Single core 630 Sq.mm Aluminum XLPE insulated Corrugated Aluminum Sheathed 132KV cable ( DC+2 spare = 8 Conductor) | — | 11.00 | — | — | |
| — | — | — | 6,22,40,310 | ||
| Sand bedding (inculding materials) and laying of cables ( 8 Cable ) in excavated trench | — | 11000.00 | — | — | |
| — | — | — | 64,95,177.28 | ||
| Composite outdoor type termination kit suitable for above cable with all accessories. | — | 16.00 | — | — | |
| — | — | — | 24,91,900.16 | ||
| Installation of 132 KV out door end termination structure on tower | — | 16.00 | — | — | |
| — | — | — | 27,69,192.68 | ||
| 1 C x 300 sq. mm Copper conductor 3.3 KV sheath bonding cable | — | 1.10 | — | — | |
| — | — | — | 49,64,067.26 | ||
| 1 C x 300 sq. mm copper conductor 3.3 KV XLPE insulated Earthing cable (ECC) | — | 2.00 | — | — | |
| — | — | — | 2,67,124.64 | ||
| Supply of 1 Phase link box with SVL | — | 8.00 | — | — | |
| — | — | — | 1,52,989.52 | ||
| Supply of 1 Phase link box without SVL | — | 8.00 | — | — | |
| — | — | — | 68,584.32 | ||
| Installation of single phase link boxes with or without SVL | — | 16.00 | — | — | |
| — | — | — | 8,74,226.24 | ||
| Supply of 120 KV Porcelain type, 10 KA, LA with insulating Base, Surge counter and terminal connector | — | 16.00 | — | — | |
| — | — | — | 6,85,844.16 | ||
| Installation of lightening arrestor towards tower and including earthing | — | 16.00 | — | — | |
| — | — | — | 81,958.5 | ||
| Supply of Route markers | — | 50.00 | — | — | |
| — | — | — | 1,23,440 | ||
| Supply of warning tape | — | 2000.00 | — | — | |
| — | — | — | 15,71,380 | ||
| HDPE pipe for crossing 200 mm Dia. PN6 PE 80 | — | 1000.00 | — | — | |
| — | — | — | 21,85,600 | ||
| RCC Protection Slab | — | 5000.00 | — | — | |
| — | — | — | 40,97,940 | ||
| Heavy Duty Aluminum clamp for holding cable on structure | — | 1000.00 | — | — | |
| — | — | — | 1,74,845.28 | ||
| Terminal connector for Termination stud to conductor on Towers | — | 16.00 | — | — | |
| — | — | — | 1,36,800.16 | ||
| Maintenance free earthing rods and connecting leads etc. | — | 16.00 | — | — | |
| — | — | — | 11,00,000 | ||
| Heavy Duty Aluminum clamp for holding bonding cable on structure (Dia. 36.5 mm) | — | 1000.00 | — | — | |
| — | — | — | 1,02,876.62 | ||
| Route Survey and preparation of drawing along with trial pits and measurement of soil thermal resistivity (Km=Km of Line) | — | 1.00 | — | — | |
| — | — | — | 24,69,036 | ||
| Excavation of trench as per drawing for Double circuit | — | 1200.00 | — | — | |
| — | — | — | 8,22,960 | ||
| Backfilling of Trench with sand, RCC covers, warning tape, route marker and filling & leveling of Surface | — | 1200.00 | — | — | |
| — | — | — | 2,05,753.24 | ||
| Modification of tower for accommodating 132 KV cable termination and lightening arrestor on tower | — | 2.00 | — | — | |
| — | — | — | 5,48,675.2 | ||
| Installation of maintenance free earthing rods connection to link box earthing of termination and LAs structure | — | 16.00 | — | — | |
| — | — | — | 1,71,461.02 | ||
| Pre commissioning tests (Per Unit = Circuit) | — | 2.00 | — | — | |
| — | — | — | 34,500 | ||
| Supply of XLPE LT Aluminium cable of size 4 core x 16 Sq. mm. multistained armoured ISI approved suitable to 1100 volt grade Make: Paragon, Havells,Nicco, Universal. | — | 300.00 | — | — | |
| — | — | — | 4,795.2 | ||
| Wall clamping of cable on wall /bridge through suitable clamp of size 50x6 mm of MS flat or catenary of cable through 4 SWG GI wire with suitable clamps (As per site requrement) | — | 360.00 | — | — | |
| — | — | — | 10,251.36 | ||
| Concealed Wiring of Light Point/Fan/Exhaust/ Call Bell point fan point in heavy gauge PVC conduit pipe as per IS 9537 with PVC insulated single core 1.5 sqmm multistrand copper conductor wire in voltage grade 1100 volt as per IS 694 with ECC of 1/18 SWG copper wire. Make : Polycab, Anchor, Finolex, cpntrolling through flush type 10 Amp. switch to be fitted with frame and Tress plate, Make of switch - ROMA, CONA,Schenieder. | — | 24.00 | — | — | |
| — | — | — | 1,625 | ||
| Concealed wiring of 6 Amp plug point in heavy gauge PVC conduit pipe as per IS 9537 with PVC insulated single core 1.5 sqmm multistrand copper conductor wire in voltage grade 1100 volt as per IS 694 with ECC of 1/18 SWG Copper wire. Make : Polycab, Anchor, Finolex.controlling through flush type 10 Amp. switch to be fitted with frame and Tress plate , Make - ROMA, CONA, Schenieder | — | 5.00 | — | — | |
| — | — | — | 152.46 | ||
| Supply,Fixing,testing and commissioning of 15/5Amp 5 in 1 combined switch, socket , fuse units duly ISI Approved as per IS:6538/1971 make: Indoasian , Anchor, EPP. Indoasian | — | 2.00 | — | — | |
| — | — | — | 6,000 | ||
| Concealed Wiring of main from main distribution board to sub board in heavy gauge PVC conduit Pipe as per IS : 9537 with PVC multistrand copper conductor of size 2 x 2.5 sqmm in voltagegrade 1100 volt as per IS: 694 with ECC of 1/18 SWG copper wire, make of wire : Finolex, Plaza, Polycab,Havells. | — | 120.00 | — | — | |
| — | — | — | 8,775.6 | ||
| Concealed wiring of main from main distribution board to sub board in heavy guage PVC conduit pipe as per IS:9537 with PVC multistrand copper conductor of size 2 x 4 sqmm in voltage grade 1100 volt as per IS:694 with ECC of 1/18 SWG copper wire, make of wire: Finolex, Plaza , Polycab,Havells. | — | 120.00 | — | — | |
| — | — | — | 10,098 | ||
| Concealed Wiring of main from main distribution board to sub board in heavy gauge PVC conduit Pipe as per IS : 9537 with PVC multistrand copper conductor of size 2 x 6 sqmm in voltagegrade 1100 volt as per IS: 694 with ECC of 1/18 SWG copper wire, make of wire : Finolex, Plaza, Polycab,Havells. | — | 120.00 | — | — | |
| — | — | — | 235 | ||
| Supply, Fixing, testing and commissioning of Jn. Box made of high quality of thermoplastics, dust and corrosion proof , water tight with cable gland similar to Hansel cat no. D - 9025 . Make - Hensel , Siemens , Indoasian . | — | 1.00 | — | — | |
| — | — | — | 9,912 | ||
| Supply, fixing, connection, testing and commissioning of LED fitting indoor type , Lumen efficiency 100 lumen/watt ,output system wattage 42W (+10%, 5%) with IP 65 or better protection water proof surface/suspendedmounting suitable for operation on 140VA 270V AC supply, LED used in fittings should be of make : NICHIA/OSRAM/ SEOUL/CREE/PHILIPS LIMITEDS/LEDNIUM with warranty period of 5 yrs from date of commissioning or 6 yrs from date of supply whichever is earlier complete with testing arrangement. Make : Bajaj, Philips, Havells. | — | 5.00 | — | — | |
| — | — | — | 12,272 | ||
| Supply of 200 watt LED Flood Light , Make - Philips , Bajaj , Havells , CG | — | 2.00 | — | — | |
| — | — | — | 2,095 | ||
| Supply of 4 Pole 300 mm. Exhaust fan as per IS : 2312 . Make : Crompton , Bajaj , Usha .orient ( GeM id no. 511687766880512. Dt.29/09/23) | — | 1.00 | — | — | |
| — | — | — | 69.6 | ||
| Fixing of Exhaust fans with suitable clmps ensuring safety of the fan. (Exhaust fan will be supplied by Railway ) | — | 1.00 | — | — | |
| — | — | — | 140.98 | ||
| Supply, fixing, testing and commissioning of 32 Amp. DP Main switch . Make - Anchor, havells, Standard , Indoasian | — | 2.00 | — | — | |
| — | — | — | 6,753.64 | ||
| Supply, Fixing , testing and commissioning of MCCB DB for distribution of 3 phase supply 415 volt AC comprising with following : For incoming : 1 ) MCCB 4 pole 100 A - 01 nos, make Siemens cat no. 3 V T 82161 A A - 040 A A Z , OR SIMILAR For Outgoing : 2 ) MCB SP 06 A to 32 AMp - 08 nos, as per site requirement, make: Siemens, L&T, Standard, HPL 3 ) Beta bus plus vertical Bus Bar DBs with MCCB incoming cat No. 8 GB 31571RC Make : Siemens, L&T, Havells,Indoasian ( Optium ) | — | 1.00 | — | — | |
| — | — | — | 1,072.46 | ||
| Supply of SPN Distribution Board single Door 8 way Product code DHDNSHODAW08 of Havells. Make - Havells, Indoasian , Havells , C&S, | — | 1.00 | — | — | |
| — | — | — | 483.16 | ||
| Supply of single pole 6 - 16-32 Amp , MCB. Make - Havells, Indoasian , Havells , C&S. | — | 4.00 | — | — | |
| — | — | — | 69.01 | ||
| "Fixing, testing and commissioning of Distribution Board , Street Light Panel etc.. " | — | 1.00 | — | — | |
| — | — | — | 3,312.56 | ||
| Supply, fixing,testing and commissioning of 4 Pole 100 Amp. MCCB with sheet steel enclosure .Make - Siemens, L&T, Havells,Indoasian. | — | 1.00 | — | — | |
| — | — | — | 3,135.44 | ||
| "Supply, Fixing, Testing and commissioning of 4 pole 63 Amp change over switch in sheet steel enclosure duly ISI approved of make :Siemens, L&T, Havells, Aarkey Lite, HPL., C&S " | — | 1.00 | — | — | |
| — | — | — | 3,142.5 | ||
| Supply, Fixing, Testing and commissioning of power contactor 3 pole type MX mini 25 Amp ML 1.5 type 02 No + 02 NC (coil voltage 240 V / 50 Hz.) as per Cat No. :SS91851 of L&T as per IS 60947-4-1 with enclosure of hylum sheet , Insulator in GI Box of 8" x 6". Make -L&T, Siemens, ABB. | — | 1.00 | — | — | |
| — | — | — | 9,900 | ||
| "Supply of octagonal pole (Dip Galvanised in single dep average 70 micron) 6 mtrs. Long Top dia 70 mm , Bottom Dia. 135 mm. Sheet thickness 3 mm. in single section with base plate (220 x 220 x 12 mm L x B x H) with 700 mm Long Double Arm Bracket and 04 Nos. 16 mm dia. x 600 mm long (100 mm. thread projectional ), foundation Bolts , complete with smart pack junction Box with 6 A MCB and stud terminals (For mounting inside base plate) and Internal wiring for terminal to fitting with 2 x 2.5 Sq. mm. cable of Reputed make i.e. Polycab , finolex , Havells ,Anchor , Plaza ) Make of pole : Bajaj , Bansal , Jindal , UTKARSH Transrail Lighting Ltd. , Gamson Group , BPP " | — | 1.00 | — | — | |
| — | — | — | 1,941.16 | ||
| "Erection and casting of Foundation for Octagonal Tubular pole with earth excavation with cement , concrete and sand (1 :3 :6) and muffing of Base Foundation as per manufacturers drawing and dimension as required under the suppression of site incharge " | — | 1.00 | — | — | |
| — | — | — | 12,290.02 | ||
| Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer- incharge. 2.6.1 All kinds of soil | — | 59.82 | — | — | |
| — | — | — | 94,392.91 | ||
| All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cu | — | 10.87 | — | — | |
| — | — | — | 12,967.2 | ||
| Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | — | 6.00 | — | — | |
| — | — | — | 80,043 | ||
| 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) | — | 12.00 | — | — | |
| — | — | — | 88,381.8 | ||
| 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | — | 12.00 | — | — | |
| — | — | — | 1,83,330.9 | ||
| 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | — | 18.00 | — | — | |
| — | — | — | 1,59,798 | ||
| Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) | — | 24.00 | — | — | |
| — | — | — | 3,72,975.75 | ||
| "Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in" | — | 45.00 | — | — | |
| — | — | — | 48,255 | ||
| Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts | — | 60.00 | — | — | |
| — | — | — | 45,993 | ||
| "Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform" | — | 60.00 | — | — | |
| — | — | — | 36,501 | ||
| "Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers cantile" | — | 60.00 | — | — | |
| — | — | — | 10,354.8 | ||
| Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : 6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) | — | 12.00 | — | — | |
| — | — | — | 113.4 | ||
| Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. | — | 9.00 | — | — | |
| — | — | — | 29,020.5 | ||
| Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | — | 3.00 | — | — | |
| — | — | — | 2,03,040 | ||
| 12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand) | — | 720.00 | — | — | |
| — | — | — | 33,673.5 | ||
| 12 mm cement plaster finished with a floating coat of neat cement of mix : 13.7.1 1:3 (1 cement: 3 fine sand) | — | 90.00 | — | — | |
| — | — | — | 59,448 | ||
| Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete | — | 480.00 | — | — | |
| — | — | — | 10,104.48 | ||
| Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | — | 10.80 | — | — | |
| — | — | — | 63,807 | ||
| Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | — | 60.00 | — | — | |
| — | — | — | 1,27,498.5 | ||
| Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm | — | 90.00 | — | — | |
| — | — | — | 5,91,690 | ||
| Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe- 500D or more | — | 6600.00 | — | — | |
| — | — | — | 318.3 | ||
| "Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :150x10 mm" | — | 6.00 | — | — | |
| — | — | — | 169.5 | ||
| Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm | — | 6.00 | — | — | |
| — | — | — | 414 | ||
| Providing and fixing ISi marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : 250x20x6 mm | — | 6.00 | — | — | |
| — | — | — | 5,137.8 | ||
| Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete | — | 6.00 | — | — | |
| — | — | — | 1,06,720.85 | ||
| Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) Sal wood | — | 1.00 | — | — | |
| — | — | — | 33,822 | ||
| 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | — | 12.00 | — | — | |
| — | — | — | 52,074 | ||
| For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | — | 120.00 | — | — | |
| — | — | — | 44,671.2 | ||
| Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | — | 84.00 | — | — | |
| — | — | — | 27,836.55 | ||
| Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | — | 21.00 | — | — | |
| — | — | — | 2,37,240 | ||
| Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. | — | 1200.00 | — | — | |
| — | — | — | 95,370 | ||
| Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | — | 600.00 | — | — | |
| — | — | — | 12,386.25 | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes | — | 45.00 | — | — | |
| — | — | — | 22,239 | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes | — | 60.00 | — | — | |
| — | — | — | 67,104 | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40 mm nominal dia Pipes | — | 120.00 | — | — | |
| — | — | — | 1,311.8 | ||
| Providing and fixing brass bib cock of approved quality : 20 mm nominal bore | — | 4.00 | — | — | |
| — | — | — | 1,573.8 | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 18.46.1 15 mm nominal bore | — | 6.00 | — | — | |
| — | — | — | 1,156.2 | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore | — | 4.00 | — | — | |
| — | — | — | 1,477.4 | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25mm nominal bore | — | 4.00 | — | — | |
| — | — | — | 2,092.8 | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore | — | 4.00 | — | — | |
| — | — | — | 5,781.35 | ||
| Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | — | 1.00 | — | — | |
| — | — | — | 28,777.5 | ||
| Providing and fixing 110mm dia PVC soil, waste and vent pipes including jointing and cost of spun yarn and sand etc. complete | — | 90.00 | — | — | |
| — | — | — | 616.35 | ||
| pvc equal junction | — | 3.00 | — | — | |
| — | — | — | 396 | ||
| Providing and fixing 110mm PVC bend including jointing and cost o f spun yarn and sand etc. complete | — | 3.00 | — | — | |
| — | — | — | 4,550 | ||
| Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap | — | 2.00 | — | — | |
| — | — | — | 1,784.25 | ||
| Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bor | — | 3.00 | — | — | |
| — | — | — | 7,618.5 | ||
| Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | — | 30.00 | — | — | |
| — | — | — | 995.4 | ||
| Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm | — | 6.00 | — | — | |
| — | — | — | 14,532 | ||
| Extra for providing and mixing water proofing material in cement of plaster work in proportion recommended by the manufacturers. | — | 240.00 | — | — | |
| — | — | — | 5,268.85 | ||
| Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cister | — | 1.00 | — | — | |
| — | — | — | 27,135 | ||
| Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). | — | 60.00 | — | — | |
| — | — | — | 11,29,581 | ||
| Formation of Trench less road crossing with HDPE pipe for Double circuit. | — | 100.00 | — | — | |
| — | — | — | 1,80,362.76 | ||
| "Stringing and sagging of one no. galvanised stranded steel wire as earth wire (7/3.15 mm) including laying, stringing, tensioning, clamping, jointing etc. on the 220KV or 132KV towers / gantries / Rail Poles etc, complete including storing, handling, transporting of all materials to site per route Kilometer of the line including fixing of hardwires, vibration damper and/or armour rods ( erection of clamps repair sleeve, Vivaration damper armour rods, completion joints & installation of earth bond with PG clamps are including )" | — | 12.00 | — | — | |
| — | — | — | 6,65,368 | ||
| Supply of Galvanised bolts and nuts | — | 4.00 | — | — | |
| — | — | — | 1,05,556.25 | ||
| Supply of AAA C Panther conductor | — | 0.50 | — | — | |
| — | — | — | 49,861.44 | ||
| Supply of 70KN disc insulator | — | 24.00 | — | — | |
| — | — | — | 4,00,416.24 | ||
| Supply of 120KN Disc insulator | — | 168.00 | — | — | |
| — | — | — | 1,93,309.53 | ||
| Galvanised stranded steel earth wire ( 7/3.15mm) as per specification | — | 2.20 | — | — | |
| — | — | — | 54,292.14 | ||
| Single suspension hardware set with Armour grip suspension clamp and Preformed Armour rods suitable for AAA Panther Conductor (37/3.15 mm) and suitable for fixing on (a) 132 KV Tower(failing load 70KN) | — | 18.00 | — | — | |
| — | — | — | 1,32,866.82 | ||
| Double suspension hardware set with Armour grip suspension clamp and Preformed Armour rods suitable for AAA Panther Conductor (37/3.15 mm) and suitable for fixing on (a) 132 KV Tower(failing load 70KN) | — | 18.00 | — | — | |
| — | — | — | 2,30,934.24 | ||
| Single Tension Hardware set with compression type tension clamp suitable for AAA Panther Conductor (37/3.15 mm) and suitable for fixing on (a)132 KV tower (Failing load 120 KN) | — | 72.00 | — | — | |
| — | — | — | 5,21,836.56 | ||
| : Double Tension Hardware set with compression type tension clamp suitable for AAA Panther Conductor (37/3.15 mm) and suitable for fixing on (a)132 KV tower (Failing load 120 KN) | — | 72.00 | — | — | |
| — | — | — | 51,476.22 | ||
| Single Suspension Pilot Insulator Hardware Set suitable for AAA Panther Conductor (37/3.15 mm)& suitable for fixing on (a)132 KV Tower (failing load 70 KN) | — | 18.00 | — | — | |
| — | — | — | 1,24,977.6 | ||
| Vibration damper suitable for AAA Panther Conductor (37/3.15 mm) | — | 144.00 | — | — | |
| — | — | — | 11,836.05 | ||
| Mid span compression joint for AAA Panther Conductor (37/3.15 mm) | — | 15.00 | — | — | |
| — | — | — | 6,993.45 | ||
| Repair Sleeve suitable for AAA Panther Conductor (37/3.15 mm) | — | 15.00 | — | — | |
| — | — | — | 6,003.36 | ||
| Suspension hardware set for Galvanised Stranded Steel Wire (7/3.15 mm) and suitable for fixing on (a)132 KV tower | — | 6.00 | — | — | |
| — | — | — | 11,907.12 | ||
| Tension hardware set compression type with complete tension clamp and flexible copper bond for Galvanised Stranded Steel Wire (7/3.15 mm) and suitable for fixing on ( supply of Earth bond also include) (a)132 KV tower | — | 12.00 | — | — | |
| — | — | — | 22,547.28 | ||
| Vibration damper suitable for Galvanised Stranded Steel Wire (7/3.15 mm) | — | 24.00 | — | — | |
| — | — | — | 4,932.9 | ||
| Mid span compression joint for Galvanised Stranded Steel Wire (7/3.15 mm) | — | 10.00 | — | — | |
| — | — | — | 3,567.4 | ||
| Repair Sleeve suitable for Galvanised Stranded Steel Wire (7/3.15 mm) | — | 10.00 | — | — | |
| — | — | — | 1,04,775.48 | ||
| Pipe type Earthing Materials (Galvanised) (Supply of earth bond with copper lugs also included) | — | 12.00 | — | — | |
| — | — | — | 1,481.4 | ||
| Counterpoise type Earthing Materials (Galvanised) (Supply of earth bond with copper lugs also included) | — | 6.00 | — | — | |
| — | — | — | 2,082.36 | ||
| Danger Plate | — | 6.00 | — | — | |
| — | — | — | 2,082.36 | ||
| Number Plate | — | 6.00 | — | — | |
| — | — | — | 11,463.48 | ||
| Phase Plate (set of 3) | — | 36.00 | — | — | |
| — | — | — | 3,821.16 | ||
| Circuit Plate (set of 2) | — | 12.00 | — | — | |
| — | — | — | 18,728.46 | ||
| Bird Guard | — | 18.00 | — | — | |
| — | — | — | 36,055.32 | ||
| Anticlimbing Device excluding barbed wire, bolt, nut, washers (galvanised and assorted) (a)to fit different 132 KV tower | — | 6.00 | — | — | |
| — | — | — | 3,188.64 | ||
| PG clamp suitable for AAA Panther Conductor (37/3.15 mm) | — | 6.00 | — | — | |
| — | — | — | 2,943.36 | ||
| Non Tension joint suitable for AAA Panther Conductor (37/3.15 mm) | — | 6.00 | — | — | |
| — | — | — | 50,73,292.66 | ||
| DESIGN, FABRICATION, GALVANIZING AND SUPPLY OF TRANSMISSION LINE STEEL MONO POLE INCLUDING ANCHOR PLATE, ANCHOR BOLTS, TEMPLATES SUITABLE FOR 132kV-DC- PC30(15-30D)_BXA@ 20m (SPAN=320M, ACSR PANTHER, OPGW, OLF=1.12, TENSION=22%) | — | 1.00 | — | — | |
| — | — | — | 94,68,851.2 | ||
| Supply of 132KV Monopole/DESIGN, FABRICATION, GALVANIZING AND SUPPLY OF TRANSMISSION LINE STEEL MONO POLE INCLUDING ANCHOR PLATE, ANCHOR BOLTS, TEMPLATESSUITABLE FOR 132KV D/C PD 30-60 | — | 1.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .