REPAIR TO WATER PROOFING TREATMENT, SUNKEN FLOOR, RAIN WATER PIPE, WATER SUPPLY, PLUMBING, SANITARY ITEMS AND CONNECTED ITEMS INCLUDING E/M ITEMS IN CERTAIN MD ACCN AT ALBERT EKKA ENCLAVE UNDER AGE B/R-II AT NAMS

Amount

Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

Taking down old shutters of any description exc. 1.0sqm but not exc. 2.0sqm each complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent ement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as per manufacturer's instruction complete all as specified all as specified.

S&F PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinf with MS square tube supplying & fixing in opening as per specificationn complete all as specified and directed.

S&F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F 35 mm thick plain, framed, panelled shutters with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed.

Material & labour for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc including provn of cooler/AC opening etc. (a) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (b) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (e) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (f) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf (g) 12 mm square guard bar, 10 cm centre to centre. (h) 25x4 mm flat iron all around for joint of both frame. (j) One shop coat of red oxide primer and two coats of Synthetic enamel paint to MS window and guard bar Note: (i) Including taking down old steel window/ ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge. (ii) sheet glass and wire mesh shall be measured and paid separately)

Material & labour for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame (single rebated ) of ERW and FI 2mm thick welded /screwed to frame for fixing of sheet glass including fixtures and fittings like a stopper , cleat , pintal hinges , holdfast etc all as shown on drg No CEJZ/TD/1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a) 10mm Sq Guard bar 10cm C/C (b) One shop coat of red oxide and two coats of synthetic enamel paint to MS ventilator and gaurd bar (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf Note: (i) Including taking down old steel ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge. (ii) sheet glass and wire mesh shall be measured and paid separately)

S&F Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane fix with oil putty complete all as specified and directed. (Note upto four storey height including all scaffolding work )

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed tinned or stainless steel wire staple complete all as specified and directed.

S&F in repair 3mm thick plain glass etc and glazing with oil putty in Sqm n.exc 0.50 each pan complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed tinned or stainless steel wire staple complete all as specified and directed.

S&F Stainless steel butt hinges 100mm long medium weight fixed complete all as specified and directed

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F aluminium handle cast type, anodised 150mm size conforming to IS complete all as specified and directed.

Taking down cement plaster on Brick/concrete surface etc including racking out of joints hacking for keys scrubbing down with water complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair face of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on fair face of brick or concrete surface finished even and fair all as specified and directed.(WPC shall be measuared seperatly as per manufacturer's instructions). Note Rate applicable upto four story high bldg incl necessary scaffolding etc.,

M&L, rendering 10mm thick in CM 1:3 over concrete surface as on ceiling finish even and smooth w/o using extra cement , complete all as specified and directed.

M&L for applying two coats of Acrylic smooth exterior emulsion paint over a coat of primer on walls, pillars cornices etc surface incl preparation of new plastered surface to obtain smooth finish using sand paper etc complete all as specified and directed.

M&L for applying one coat of Acrylic smooth exterior emulsion paint on walls, pillars cornices etc surface incl preparation of old plastered/painted surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and incl filling holes necessary where required with putty as in pathces or nail holes to obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

M&L Prepration of new plastered surface and applying 3 coat of white wash on ceiling complete all as specified and directed

M&L for preparation of old decorated plaster or un- plastered surfaces and providing two coats of white wash on ceiling etc, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

Supply only liquid WPC complete all as specified and directed.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 20 mm thick screed bed or bedding layers in CM 1:6 complete all as specified and directed

M&L for glazed ceramic coloured tiles size s of size 450x300x7mm thick on vertical surface in skirting /dado etc. ,set and jointed in neat cement slurry and pointed with white cement with pigment to match the colour of tiles, 10 mm thick rendering on fair faces of concrete surface of verticle in CM (1:3) finished even and smooth without using extra cement complete, shade & design as approved by EIC complete all as specified.

Material and labour for 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L for 18-20mm thick black granite stone (of any type) machine cut, bedded and jointed with gray cement slurry and pointed with white cement with admixture or pigment to match the shade of stone in window cills, jams,cooking platform pillars etc.laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rounding and rubbing and polishing complete all as specified and directed.

S&F in replacement 500 ltrs capacity rotatonal moulded polyethylene water storage tanks Triple layer in white colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including S&F of ball brass valve high pressure of 20mm dia complete all as specified and directed.

S&F in repair Bib tap CP fancy type/long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe complete with all fittings all as specified and directed.

S&F in repair Stop cock concealed long shank chromium plated fancy type 15 mm bore screwed down high pressure fixed to iron pipe complete all as specified and directed.

S&F in repair Angle cock CP fancy type 15 mm bore screwed down high pressure foxed to iron pipe or for Unions complete all as specified and directed.

S&F in repair two way Angle cock CP fancy type 15 mm bore screwed down high pressure screw both end for iron pipe or for Unions complete all as specified and directed.

S&F in repair brass chromium plated shower rose with Arm length not less than 150mm swivel joints size 125mm with arm fixing to steel pipe or union complete all as specified & directed

S&F in repair tubular towel rail 600mm long, 20mm dia 'D' type CP rail with fixed in wall complete all as directed

S&F for in repair swan neck 15mm pillar cock chromium plated fancy type screw with iron pipe incl all fittings complete all as specified and directed.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets for low levels flushing cistern etc complete all as specified and directed.

S&F in repair, Viterous China wash down water closet pan (pedestal pattern) coloured including 'P' or 'S' trap incl plastic seat cover white closed pattern with float bottom and cover and jet connection and mild steel chrominum plate or aluminized hanging device complete all as specified and directed.

S&F in repair for viterous china squating pan of (Orrissa Pattern) size 580 x 440 white with 'P' or 'S' trap front or back inlet and integral foot rest , including joining, filling and provision of cement concrete bedding 1:5:10, type E2 (excluding flushing cisteern and flush pipe) fixed incl cement concrete bedding as required set complete all as specified and directed.

S&F in repair vitreous China wash basin white,flat back size550x400mm including CP waste coupling 32mm bore, including padestal and bracket for fixing etc complete all as specified and directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size complete all as specified and directed.

S&F PVC waste pipe 32/38/40mm bore including socket complete all as specified and directed.

S&F in repair CP grating 125mm dia circular of approved make and fixing with cement mortar 1:3 complete all as specified and directed.

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends fixed for iron pipe of complete all as specified and directed.

Taking down 15mm bore old PRP pipe connections including cleaning or removal from site comlete all as specified and directed.

All as per ser item No 51.00 above but 20 mm bore complete all as specified and directed

S&F GI tubing 15mm bore medium grade including all fittings fixed to walls and ceilings or laid in floors at site complete all as spcified and directed.

All as per ser item No 53.00 above but 20 mm bore complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using sub class ‘B’ bricks, straight or corved on plan exc. 6 mean radius in CM 1:6 complete all as specified and directed

All as per ser item No 56.00 above but except brick complete all as specified and directed.

Dismantling brick tiles or terraling single layer as in roofing complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and dispose from site exc 500 mtr complete all as specified.

M & L for 50mm avarage thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as roof padding ,hunching, sub base floor, even and smooth without using extra cement for further treatment complete all as specified and directed.

M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

M&L, 40 mm thick brick tiles laid over 15mm thick cement motar (1:6) and joints grouted flush in cement Motar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed.

All as per ser item No 62.00 above but except bricks tiles complete all as specified and directed.

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc 50 m complete all as specified and directed.

M&L for applying two coat of undiluted thick coat of acrlic reinforcement liquid applied elastorneric water proofing membrane with UV resistance properties and solar refective properties over one coat of primer (1:3, Dilution:water) Note: Every each coat gap between 6 hrs) complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors and wall complete all as specified and directed.

S&F PVC (SWR) bend 110 mm with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single T equal or unqual complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm dia complete all as specified and directed.

S&F stack clamp out of 50mmx5mm flat iron and 16mm dia round iron stay including bolts and nuts and securing end of stay to wall or roof for 110mm bore pipe all as spicefied and directed.

S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75mm bore PVC(SWR) bends of any radius complete all as specified and directed.

M&L for 110mm bore of pipe PCC 1:4:8 type D-2 concrete bed to drain pipes including packing under and hauching against the sides of pipes after they are laid complete all as specified and directed.

M&L for PVC(SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75/100mm complete all as specified and directed.

M&L for 110mm bore PVC Gully Trap setting / jointed with solvent cement complete all as specified and directed.

S & F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed.

Demolition of cement concrete as in sunken floor of bath,wc and kitchen of any description and any position not otherwise specifically provided complete all as specified and directed.

Material and labour for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under :- (a) Application of Two component Acrylic modified cementitious coating (i) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturer’s published literature should be strictly complied with, including but not limited to the following :- (ii) Chipping out any visible cracks in “V-Groove” pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (iii) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO.

(iv) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions. (v) Apply Glass Fabric Sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP whilst the first coat is wet. (vi) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions on the entire area. (vii) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (viii) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface. (ix) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (x) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces.

(xi) All the corners and joints should be pre-treated with an elastic waterproofing sealing tape with a Woven bonding mesh on each surface and an elastic expansions zone in the centre of Make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (xii) The membrane has to be protected in accordance with the manufacturer’s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer’s recommendations (xiii) Waterproofing treatment has to be carried out through applicators authorised (b) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (c) Al CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) All-round. (d) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified (e) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (f) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note: Items No 79.02 (d), (e) & (f) shall be measured and paid separately.

M&L cement concrete in foundation above filling and mass concrete type F2 1:7:12 (40mm graded agg) as in sunken floor complete all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame, cooler/water tank stand and other similar work confirming to Fe-290i complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth & applying two coats of synthetic enamel paint over one coat of red oxide primer of approved quality, complete all as specified and directed.

S&F drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

Taking down aluminium/copper point wiring from existing conduit / batten (light, fan, socket or power) complete such as switches, ceiling rose, pendent, regulators, socket, light fittings etc and removing material from site and making good the disturbed surface of wall / floor etc, complete all as specified and directed

All as per Srl item No 85.00 above but for one 5 amps socket outlet independent complete all as specified.

All as per Srl item No 85.00 above but on the same board complete all as specified

All as per item No 85.00 above but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 2.5 Sq mm copper solid conductor connecting to common earth dolly complete.

Supply and fix of switch piano type 6 Amps one way 230 volts AC complete all as specified and as directed.

Supply and fix of socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and as directed

Supply and fix of switch piano 16 Amps type one way 230 volts AC complete all as specified and as directed

Supply and fix of socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and as directed

Supply and fix of switch type regulator 5 step 230 volts AC complete all as specified and as directed

Supply and fix of ceiling rose 65/50 mm two to three terminals complete all as specified and directed.

Supply and fix of MCB 40 Amps single pole with neutral, AC 230 Volts complete all As specified and directed.

Supply and fix of MCBs single pole (SP) 6 to 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards complete all as specified and directed.

Supply and fix in replacement Sheet metal enclosure for DB's when MCB's to be used double door factory made flush fixed complete with 200 Amps rated busbar 240 Volts single phase 12 ways complete all as specified

Supply and fix in replacement for sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit medium grade of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) and including non metallic medium grade rigid PVC conduit, including cutting chases in brick wall, and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable, one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

All as per item No 98.00 above but for 4.0 sqmm complete all as specified and directed.

Material and labour of lamp holder insulated body with 9 Watt LED Bulb, back plate batten/angle type for batten fitting fixed on bakelite sheet 100mmx100mm 230V AC cool day light 6500K having maximum height 1020 mm heavy duty complete all as specified and directed.

Supply and fixing in replacement of sheet steel enclouser distribution boards, double door factory made TPN Vertical 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as specified and directed with the following accessories :- (a) MCCB 100 amps, 16 KA, ics=75% icu,with spreader terminal, FP, 415 volts, 50 Hz = 01 No. (Note:- Out going MCB shall be measured and paid for separately)

S&F in replacement MCBs single pole (SP) 40 Amps with 10 KA breaking capacity of 'B' series in distribution boards complete all as specified and directed.

Supply and fixing of LED T-8 tube light fitting with single side connection LED tube rod 18/20 W, 4 Feet made of CRCA sheet steel box type including bipin holder and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rode to light fitting complete all as specified and directed.

Supply & fix LED Street Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens all as specified and as directed.

Supply and fixing of security light mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat of size 40 x 6 mm and nuts and bolts and painting with aluminium paint, all as direced by Engr in Charge

Supply, laying in trenches or wall and testing in replacement of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sqmm 4 core all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PART 1 , with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Excavation in trenches not exceeding 1.5m wide & not exceeding 1.5m in depth and getting out in any type of soil all as specified and as directed.

Returning, filling including spreading, leveling, watering and well ramming in layers not exc 25 cm thick all as specified and directed.

Removal of surplus excavated soil to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified.

Supply,laying & fixing in replacement double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps etc of size 63mm outer dia and 50 mm inner dia complete all as specified and directed by Engr in Charge .

Supply and lay on wall/ floor etc GI pipe light grade of dia 32 mm for protection of cable complete all as specified and directed.

Taking down ceiling fan in situ and refixing after servicing, repairing in all aspect and painting them, scratching old paint and preparation of surface for painting with one coat of white / grey enmeled paint and including cable from ceiling rose to fan complete all as specified and as directed.

Taking down geyser in situ and refixing after servicing, repairing in all aspect and painting them, scratching old paint and preparation of surface for painting with one coat of white / grey enmeled paint complete all as specified and as directed.

Taking down exhaust fan in situ and refixing after servicing, repairing in all aspect and painting them, scratching old paint and preparation of surface for painting with one coat of white / grey enmeled paint and including cable from ceiling rose to fan complete all as specified and as directed.

S & F in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one singlr pole MCB of 20 amps complete all as specified and as directed.

Supply and fixing in replacement of bell push 6 amps one way 230 volts AC complete all as specified and as directed.

Supply and fixing in replacement of bell ding dong AC 230 volts complete all as specified and as directed.

Supply and fixing in replacement pvc connection of size 600 mm length 15 mm dia all as specified and as directed.

Santokh Singh and Associates (BID ID -3484050)

tarlok singh contractor (BID ID -3484066)