SPECIAL REPAIR TO OR MD ACCN BLDG NO. P/OR/507/01 TO 06 AT SUKNA MIL STN UNDER GE SUKNA

Amount

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges, valley gutter etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering, cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering, cladding to wall, ridge, valley gutter, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) of any description & in any position as in sunken floor etc, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement building boards (4mm thick pre-painted designed type E-Board) to Aluminium frame work with screws in ceiling (flat and/or slopping) and in jointless finish with & including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Provision of Aluminium Frame work is not included in the scope of above item.

M & L for Anodised aluminium snap grid (size of grid 605 x 605 mm) frame work for false ceiling (including provision of supporting hanger consisting of 4mm dia GI wire all as directed) complete in all respects as specified in Paras 10.38 & 10.38.1 of MES Schedule Part 1 and as directed.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 8 above but 20 mm bore

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item no 10 above but 20 mm bore pipes.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc, and also application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate etc, and also application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S & F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and shown in drg for SI No. 8095 on Ser Page No. 160 in SSR-2010 (Part-II).

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail, on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as shown on drawing on Srl Page No 156 of SSR Part-II, complete all as specified and as directed.

S&F Factory made 30mm thick flush shutter, solid core construction, with MDF Board, Exterior Grade, prelaminated both sides with decorative choice laminations including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

M&L for the Framed work such as framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including Galavanised wire staples etc, complete all as specified and as directed.

S&F 3mm thick Figured glass, pin head type and glazing for Aluminium Joinery or for steel surrounds with & including oil putty for steel surrounds, in squares n exc 0.50 sqm in each pane, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt 150 mm long of extruded section, complete all as specified and as directed.

All as per item No 28 above, but 125 mm long.

S&F mild steel Helical door spring 150mm long, ordinary rat tail rod pattern including roaller & roller plate, fixed with and including screws to wooden frames or with welding to steel frames, complete all as specified and directed.

S&F Floor door stopper (Overall length of cover plate 140mm) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and as directed.

Taking down steel window, ventilators including guard bars/ grills (where occures), also including cutting holes for taking out of lugs etc and disposing off the debris outside the premises, complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, also including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per item No 33 above but steel windows without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Taking down Wooden/PVC/Flush shutter of any description, area exc 1.00 Sqm and not exc 2 Sqm each, complete all as specified and as directed.

S&F 18/19mm thick, prelaminated partical board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination including provision of 4mm thick (with width equal to the width of shutters) 2nd class hard wood beading to the exposed edges of board, complete all as specified and as directed.

S&F in repair 12mm thick (7 Ply), plywood grade BWR, type-BB as in shelves etc, including provision of 2nd class hard wood supports of size as directed by the GE, complete all as specified and as directed.

S&F 100mm size Hasp and staple, safety type, aluminium anodised, with mild steel hinge pin, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

M&L for 25mm thick PCC Type B-0 (1:2:4) (using 12.5mm graded stone aggregates) as in sub-base of floors etc and finishing cement concrete surfaces even and fair/rough, complete all as specified and as directed.

M&L for brushing neat cement slurry with 1.00 kilogram of cement per square metre over roof surfaces, sunken surfaces etc, providing 10 mm thick plastering in cement mortar 1:3 mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M&L for applying evenly bituminous tack coat @ 1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per Sqm on the surfaces of the sunken floor , complete all as specified and as directed.

M&L for cement concrete 1:5:10 type E-2 using 40mm graded brick aggregate as in sunken portion of WC etc, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 45 above but for vertical surfaces such as skirting etc, over and including 10mm thick back coat in CM 1:4.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for 18 to 20mm thick Machine cut kota stone slabs of size 590mm x 590mm in flooring, laid over and including 20mm thick screed in cm 1:6, set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

M&L for preparaton of old/new surfaces of wall/ceiling and applying two coats (thickness of both coats minimum 2mm) of Birla/Asian wall care putty, complete all as specified and as directed.

M&L for preparing new surfaces of walls duly applied with wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for complete removal of existing treatment of wall, preparing the new surfaces of walls duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for complete removal of existing treatment from the surfaces of ceiling, preparing the surfaces and applying three coats of white wash, complete all as specified and as directed.

M&L preparing new plastered external surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed.

M&L for complete removal of existing treatment from the external surfaces of walls, preparation of the surfaces and applying two coats of cement base paint, complete all as specified and as directed.

M&L for preparing old decorated surfaces of wall and applying one coat of white wash, complete all as specified and as directed.

M&L preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L preparation of steel surfaces duly applied with shop coat of primer of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of shop coat primer not included in the scope of above item.

Dismantling water tanks exc 500 litres but not exc 1000 litres capacity including disconnecting the connections, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F continous (piano) hinges, mild steel, bright finish or electro galvanised, width of flap (when open) 30 mm, complete all as specified and as direced

S&F in repairs Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 210 grms), complete all as specified and as directed (The ball valves shall be of make- Prayag : Cat No. 152 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs angle valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-526KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-513AKN/SQT-513BKN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed. (Make : ESSCO : Cat No. SQT-511KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs Pillar taps with Aerator, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed (Pillar tap shall of make ESSCO : Cat No. SQT-508KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore, complete all as specified and as directed.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of approx size 260 x 440 x 580mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, the WC Pan shall of make JAQUAR : Cat No. CNS-WHT-OP01 or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs 20mm dia Harrison rails (curtain rails), mild steel, chromium plated with and including fixing brackets, stops, rollers etc, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repairs sink with drainage board made of 0.80 mm thick sheet of stainless steel (Bronze range 204 super steel : Matt) for kitchen or laboratory with and including plugs, washers, wastes; 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall approx size 914mm x 460mmx203mm with bowl size 405mm x 354mm x 203mm, Make Prayag : Cat No. 939-DM or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs 15mm size PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed (The Shower Rose & Shower Arm shall be of make : Prayag Polymers Pvt Ltd : Cat No. BOS-11 & BOS-48 respectively or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications as approved by the GE).

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed. (Towel Rail shall be of make- Prayag : Cat No. BA-01 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S & F in repairs 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc and/or laid in trenches, complete all as specified and directed. Notes :- (i) Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation and earth work shall be measured and paid for separetly.

S & F in repairs 75 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc and/or laid in trenches, complete all as specified and directed. Notes : (i) Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces. (ii) Excavation and earth work shall be measured and paid for separetly.

S&F in repairs 75mm bore uPVC (SWR), junction single, (Single T) equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F in repairs 110mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja, kerbs, roof padding, staging of water tank, including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying minimum 3mm thick APP modified water proofing polymeric membrane reinforced with non woven polyester fibre using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption,% - Not more than 0.15. (ix) Cold flexibility - (-) 50C. (x) Dimentional stability % change = Maximum 1%. (xi) Heat Resistance - Does not dirp at 1200 C Note : The quoted rate shall also be deemed to include for cutting grooves of size and shape as required in the parapet wall for tackling the APP membrane in the wall including making good the surfaces of groove as well as damaged surfaces of the wall after tackling of membrane in CM 1:3 to match with the adjoining surfaces.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane, complete all as specified and directed.

Demolition of PCC padding, roof kerbs, wall coping etc including taking down existing un-servicable waterproofing treatment from roof slab surfaces etc, cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

Dismantling of loose / designtegrated portion of RCC chajja , bands , shelves , beam ,RCC railing , balcony and similar work ( including provision of support , formwork and welding of reinforcement with coating of anti corrosive chemical to the exposed surfaces of reinforcement) and dubbing with PCC (1:2:4), 15 to 25 mm thick using 6 to 12 mm graded stone agg mixed with WPC after applying cement slurry @ 3 kg/sqm and finished even and smooth to desired shape for triple storey bldg, complete all as specified and as directed. Notes : (i) Only WPC shall be measured and paid separately. (ii) For the payment purposes, only volume of PCC 1:2:4 shall be considered.

S&F in repair Soap dish, PTMT, Cat No. 1951 of make PRAYAG or equivalent of any other make as mentioned in Appendix 'B' of Particular Specifications, as approved by the GE, to wall with and including plugs, with chromium plated screws and wooden/plastic cleats, complete all as specified and directed.

S&F in repairs for 75 mm bore outlet uPVC (SWR) floor trap with and including grating, also including jointing with solvent cement and provision of PCC 1:2:4 (type B-1 : using 20mm graded stone aggregates) block of required size for fixing of floor trap, complete all as specified and as directed.

S&F hold fasts; wall ties; hooks for hanging fans and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

M&L for 18 to 20mm thick machine cut and prepolished kota stone slab as in skirting, landing, risers and treads (single piece stone slabs shall be provided for risers and treads of the steps) (including making 3 groves on the Kota Stone Treads) over and including 15mm thick cement mortar bed in CM 1:4, jointed and pointed with grey cement slurry mixed with pigments to match with the shade of the slabs, also including moulding / rounding to the edges of the slabs, complete all as specified and as directed.

Janata Enterprises

M/s TALCO

PS ENTERPRISE

M/S RANEN PAL

Shri U K Ghosh