ADDITION AND ALTERATION TO TEST CELL-6 (BUILDING NO P-70) AT GTRE, BANGALORE

Amount

M&L pre-cast cement concrete block masonry type C1 1:3:6 (20 mm graded aggregate) with solid blocks, exceeding 10cm in width and setting in cement and sand mortar 1:6 complete all as specified and directed.

M&L 10 mm thick internal plaster in CM 1:6 on faces of walls , finishing the surfaces even and smooth w/o using extra cement complete all as specified and directed.

M&L preparing new plastered surfaces of walls and applying two coats of plastic emulsion paint over a coat primer over and including one coat of 3mm wall care putty and preparation with sand paper to receive primer coat complete all as specified and directed.

S&F anodised aluminium frame powder coated for doors and windows, ventilators, partition with one or more rebates including joining cleat,rubber beading for fixing complete all as specified and directed. (Min thickness of Powder coating 50 Microns)

S/F 9 mm thick pre laminated particle boards exterior grade, prelaminated both sides with decorative chocie laminations fixed in aluminium partions/doors with rubber beadings complete all as specified and directed.

Taking down chowkhats or frame not exceeding 1.5 Sq.m each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but n.exc 4 sqm each with shutter(s) (without taking off shutters from the frame), including removing to store, complete all as specified and directed.

S&F Anodised aluminium anodised powder coated door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door,aluminum hinges, including suitable mortice lock anodised aluminum snap beading screws etc. complete all as specified and directed. (Min thickness of Powder coating 50 Microns)

S & F sheet glass ordinary quality for 5.50 mm thick exc 0.50 sqm in each pane complete all as specified and directed.

S/F Aluminium body door closer hydraulically regulated designation No 2, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, fixed as in repairs complete all as specified and directed.

S/F floor door stopper (double headed) of aluminium body and toungue, anodized with hard drawn steel spring 150mm, fixed as in repairs complete all as specified and directed.

Dismantling WI or MS work of any description complete all as specified and directed.

S & F Collapsible steel gates, top hung,consisting of channel pickets, pivoted flat bars, top and bottom runners, rass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exc. 50m complete all as specified and directed.

S&F Anodised aluminium powder coated window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as star lock, sliding arrangement etc complete all as specified and directed (Min thickness of Powder coating 50 Microns).

S & F 4 mm thick sheet glass, ordinary quality with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers and glazing with aluminium beads in square exc 0.5 sq.m in each pane complete all as specified and directed.

M&L mild steel framed work such as grills,. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removing to a distance exc 5 Km but not exc 15 Km outside MD Land complete all as specified and directed.

M&L for providing 100mm thick vaccum dewatered floor of Ready Mix Concrete (M-25 grade) including side shuttering (MS channel) and vibrating the same using double screed vibrator, removal of excess water using vaccum pump, suction matt, floating and revolling of concrete to the required finish using skin floater and power trovel complete all as specified and as directed.

Supply and application of non metalic floor hardner @ 3 Kg/Sqm on wet concrete make (SICA fosroc or equivalent) complete all as specified and as directed.

Cutting the groove of size 3mm wide x 20mm deep using diamond cutter on vaccum dewatered floor and filling the same with bitumen complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet rein forced with MS square bar tube, in opening as per specification complete all as specified and directed.

S & F factory made Solid Panel PVC shutters 30mm thick ( Style ) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC Sheet strip of 20mm width stuck inside with solvent cement for stikes and plain colour PVC sheets for to prail lock rail and bottom rail on eithes side and as gap insert for top rail and bottom rail. paneling of plain colour PVC Sheet to be filled in the MS frame weldedn / seded to the stil and rails with suitable PVC Sheet beading and joined together with Solvent Cement , Supplying and fixing in frame at site as per specification and drawing complete all as specified and directed.

S & F in repairs of Butt hinges,100mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified and directed.

S & F in repair of Aluminium anodised barrel tower bolts 150mm long complete all as specified and directed.

S & F in repair of Aluminium handles, cast type anodised oval or 'D' type of size 150mm complete all as specified and directed.

S & F in repair of Aluminium alloy, anodised, sliding door bolt 200mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and directed.

S&F Coloured Non Skid Joint less ceramic tiles of 7 to 8 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed

S&F Coloured glazed ceramic tiles joint free of size exc 0.18 sqm but not exceeding 0.38 sqm of 7 to 8 mm thick, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store yard complete all as specified and directed.

All as per item No. 31 here-in-before but of 20mm bore complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete with all fittings complete all as specified and directed.

All as per item No. 33 here-in-before but of size 25mm outer dia with all fittings complete all as specified and directed.

S&F in repairs 20 mm dia Gun metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs Stop valve or angle cock cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe of bore 15mm fixed as in repairs complete all as specified and directed. Make: Bir / Leader / Kirloskar.

S&F in repairs PVC low level flushing cistern of capacity 10 ltrs including PVC flush pipe for squatting pan fixed to wall ISI marked completed with brackets and accessories fixed as in repairs and making good to disturbed portion complete all as specified and directed. Make: Hindware / Cera / Parryware.

S&F in repair of Rotational moulded polythene water storage tanks double layer (cylinder each vertical with closed top) of capacity 1000 Itrs, hoisted and fixed in position complete all as specified and directed.

S&F in repairs Ball brass valve high pressure with polythene float and fly out nut, screwed for iron pipe or brass ferrule and fixed to dia of pipe 25mm complete all as specified and directed.

S&F in repair of vitreous china comet counter top wash basin in oval shape, white of size 570x450mm placed on granite platform. Make : Hindware or equivalent in Cera/Jaquar

S&F in repair of Pillar tap fancy type cast copper alloy, with capstan head chromium plated, screwed down high pressure, with or without letter 'Hot' or cold with long screwed shanks and fly nut screwed for iron pipe of bore 15mm , complete all as specified and directed by Engineer-In-Charge weight of pillar tap shall not be less than 665 gms).

Dismantling of cast iron or PVC SWR pipes of any description , fixed in any position including all connections and fittings complete all as specified and directed.

S&F PVC (SWR) soil, waste and vent pipe of bore 75mm single socketed, in any length with rubber ring joints fixed to wall including all accessories .

S&F PVC (SWR) soil, waste and vent pipe of bore 110mm single socketed, in any length with rubber ring joints laid in trenches or in floors incl all accessories complete all as specified and directed.

All as per item No. 44 here-in-before but of bore 75mm fixing under floor complete all as specified and directed.

S&F in repairs PVC (SWR) bends (any radius) size 110mm complete all as specified and directed.

All as per item No. 46 here-in-before but of size 75mm complete all as specified and directed.

S&F in reapirs PVC (SWR) multi floor trap with 75mm dia out let with grating including jointing with solvent cement complete all as specified and directed..

S&F in repairs PVC (SWR) vent cowl of 75mm bore complete all as specified and directed.

S&F in repair of 450mm long PVC connection with PTMT check nuts for 15mm bore pipes of approved quality complete all as specified and directed.

S&F in repair of Liquid soap container of PTMT fixed with and including Chromium plated brass screws and woden/plastic cleats.(Minimum weight 105gms) complete all as specified and directed.

S&F in repair of Vitreous China urinals, half stall urinal (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

S & F in repair of Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed (Minimum weight 60gms).

S & F in repairs Vitreous china urinal partition white of size 310 x 700mm complete all as specified and directed.

S&F in repairs Chromium plated two in one bib cock complete all as specified and directed. (Make : Jaquar /parryware/ cera)

S&F in repairs of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S &F in repairs towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (min wt 190 gram) complete all as specified and directed.

Material and labour for preparation of old wall surfaces by preparing wall surfaces and applying two coat of oil bound distemper paint complete all as specified and directed

M&L 3 mm thick wall care putty on wall complete all as specified and directed.

Material and labour for preparation of old wall surfaces and applying two coat of epoxy paint complete all as specified and directed

M&L Finishing walls with Acrylic Smooth exterior paint of required shade two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) incl removal of existing treatment on wall ceiling surfaces including cornices, plasters etc by scrapping/down with wire brushes and washing down and removing existing loose finishes particles etc complete all as specified and directed.

Preparation of old painted steel surfaces of any description over 10 cm girth or width and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old painted wooden surfaces of any description over 10 cm girth or width and applying one coat of synthetic enamel paint of any tint all as directed by Engineer-in-charge

Demolition of cement concrete padding in roof (unreinforced) including removal of existing roof treatment of any description and in any position not otherwise specifically provided for and including removing debris to a distance exc 5 Km but not exc 15 Km outside MD Land complete all as specified and directed.

M&L for rendering 10mm thick over roof concrete surface in CM 1:3 and finishing the surface even and smooth without using extra cement with water proofing compound complete all as specified and directed (WPC shall be measured and paid seperately).

Supply only integral water proofing compound complete all as specified and directed.

(a) M & L for mechanical cleaning of surface to make it free frrom any bituminous surface residue / dirt , oil and greese et all as specified and as directed by Engr-In - charge (b)M& L for cracks treatment by cutting open cracks and cleaning it from dirt /loose materials etc and filling with Polyurethane based sealant with and including application of PU based primer all as directed by Engr-in-charge c) M& L for applying water based polyurethane modified dispersion (single component , cold applied , non toxic , VOC component ) in 03 coats including 01 coat of primer of same materials after dilution of water at 50 % or specific primer matching same materials as per manufacture specification and as directed by Engr-In-charge. Note : A layer of Geo textile grid of minimum 40 GSM sandwich in between two PU layers as per manufacturer's specification to be provided . Make : Bostik / Berger/ Fosroc/ Sika/ Asian or any other make approved by E-in-C's Branch for PU based water proofing treatment . Note : The above treatment shall be carried out by the authorised Applicator of the manufacturer as approved by GE (I).

S&F in repairs steel rolling shutters, 1.25mm lath thickness with ball bearing and gear operated type with bevel gear box and motor as specified including top cover anchoring rod, hsap and staple and one shop coat of primer erected in position as indicated, complete all as specified and directed.

M&L for Removing existing bullet proof glass n. exc 1.5 sqm of thickness 12mm double sand wiched and cleaning the same and refixing in the same location with all beadings and necessary items required for refixing complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L rendering 15 mm th in CM 1:4 on fair finish surface with water proofing compound (WPC shall be measured separately under appropriate item) complete all as specified and directed.

M&L Rendering 5 mm thick plaster in CM 1:4 on ceiling surfaces including three coat of white wash over newly plastered surfaces complete all as specified and directed.

M & L rendering 10 mm th in CM 1:6 on surfaces otherthan fair faces of brick work complete all as specified and directed.

M&L preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat primer over finish complete all as specified.

M&L for 40 mm thick PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in floors/paving finishing the surface even and smooth without using extra cement concrete complete all as specified and directed.

M&L for RCC M-25 as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; B83 slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M-25 as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished complete all as specified and directed.

M & L formwork to sides of pillars, posts, struts, piers, columns, and stanchions fair finished complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc fair finished complete all as specified and directed.

S & F mild steel stairs (framed) including stringers including stringers, treades, landing, baluster+s, hand rails etc. including cleats, brackets, etc complete all as specified and directed.

M & L for PCC 1:4:8 type D2 using 40 mm graded aggregates as in foundation filling and mass concrete complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture,With fully perforated 12 mm thick micro tegular edged . design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC >= 0.60 as per IS 8225:1987,Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85 - 90% to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm,cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, manufacturer instruction complete as directed.

Providing and fixing in position wall panelling at all heights with integral densified GRG panels/tiles of size 595 x 595 mm with 10 mm thick fully perforated square / butt edge GRG panels / tiles, having NRC (Noise Reduction coefficient) of 0.85 (minimum) as per IS 8225:1987, Light reflectance of 85-90% (minimum) Non combustible as per BS:476 (part-4), Fire performance as per BS:476 -4:1970, humidity resistance of 99%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally GRG non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification complete all as specified and directed.

S&F High rise modular flooring with the following description:- (a) The flooring material shall be of cold rolled steel sheets which are punched spot welded coated with epoxy poweder, inside of the panel is filled with foamed cement concrete for good mechanical strength, fire reisitant and good sound absoprtion property. The top cover of flooring shall have suitable finishing with Vinyl or Linoleum material finishing (a)Panel of size 600 x 600 mm and thick 30mm. (b) Bottom pedestal plate 100 mm square x 3mm thick. (c) Top pedestal plate 90 mm diameter x 3mm thick with panel locators. (d) Threaded rod assembly to be adjusted upto 450 mm. (e) 50mm long countersunk-head mechnical fastener for all corner fixed ans rigid-grid stringer systems. (f) Pedestal galvanized heavy duty stainless steel leg. (g) glavanised stringers steel with all company specification and fixtures complete all as per manufacturer instructions and as directed. Make : Leban/Unitile/Any approved make by E-in-C/ADG/Command

Taking down existing copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down existing copper/aluminium sub main wiring complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down existing MCCB/MCB DBs complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Point wiring complete with Multi stranded copper conductor size 1.5 sqmm PVC insulated, unsheathed, FRLSH cable , 1100 volts grade conforming to IS 694 multistranded , drawn in and including medium grade rigid PVC conduit 25mm dia including all accessories concealed in walls / floors/ ceiling/Roof/ RCC beams etc with and including galvanised modular flush boxes of suitable size and modular white plate with frame for mounting of fittings, modular type switches, regulator and also including 1100 Volts, FRLSH Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly for One Light / Fan Point controlled by One Switch complete all as specified and as directed.

One light point controlled by one way switch

Fan/exhaust fan point controlled by one way switch

All as per Item No. 93 here- in- above, but for 3 pin 16amps socket outlet independently, with 1100 Volts, FRLSH Grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 and including 1100 Volts, FRLSH Grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 as earth continuity conductor and connecting to earth dolly complete all as specified and as directed.

Supply & fix switch modular type single pole 1 way 6 Amp 230 volt complete all as specified and directed.B113

Supply & fix switch modular type 1 way 16A, 1 module complete all as specified and directed..

Supply & fix Socket Modular type 6A/16A 6 pin combined 2 module 230Volts grade complete all as specified and directed.

Supply & fix modular type fan regulator 120 W two module complete all as specified and directed.

Supply & fix ceiling rose surface bakelite three pin terminal complete all as specified and directed.

Dismantling and refixing the ceiling fan/Exhaust Fan complete of any type and size , cleaning, servicing, cutting and removing burnt out copper winding from the rotor assy and rewinding with super enamelled copper winding wire of suitable gauge and turns with necessary insulation materials , varnishing, reassembling, greasing to bearings checking of nuts bolts , safety split pin, bushes , capacitor and complete spray painting and testing complete all as specified and directed. Note :- Expendable stores like cotton waste/cleaning materials, grease, lubricants, machine screws, safety split pin, bots/nuts and transportation to and from site to work place are deemed to be included in rate quoted.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep 900RPM with, blades, and frame and louvers including cutting the wall of stone/ brick masomery as per the size of exhaust fan including grouting the bolts,nuts etc for fixing necessary connection with three core flrxible wire from exhaust fan to ceiling rose complete all as specified and directed.

Supplying and fixing LED batten with aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & intregrated electronic driver 1 x 20 watts fixing on wall/ celing with LED rod complete all as specified as directed.

Supply and fixing 10 Watt LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fix Recess mounted full panel LED luminaire 36 watt fitting 2' x2' with White powder coated housing & frame in CRCA sheet, High efficiency LED grade diffuser, electronic driver duly wired upto terminal block, CRI>80, Colour temperature-5700K, IP20, 50000 burning hours as per L70 Criteria, Ambient temperature-0 to 50DegC, Driver Efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection in CM-3KV, Multistage isolated Constant current-Constant voltage operated driver with range 150-270V AC and Safety extra low voltage safe level<60V DC as per IEC Standard complete all as specified and+B119 directed.

Supply and fixing at the place as directed LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp all as specifed and directed. Note : 1. All necessary fixing/ connecting arrangements of nut, bolt, MS rod, to be provided by the contractor without any extra payment from department. 2. Quoted rate is to be deemed the charges of necessary boom lift.

Supply and fixing very High efficiency round High Bay LED fittings 120 watt, 220 V AC in PDC housing complete with driver, holders & LED lamp suitable for industrial purpose including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Note : 1. All necessary fixing/ connecting arrangements of nut, bolt, MS rod, to be provided by the contractor without any extra payment from department. 2. Quoted rate is to be deemed the charges of necessary boom lift.

Supply and fix LED light fitting 1 x 16Watts, flame proof, CMRI certificated recommended for gas/vapour group of IIA & IIIB, zone 1 & 2 and IP 65 protection with die cost aluminium hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and Fix Switch flame proof rotarty type with termination box in LM,10 A single pole 250V complete all as specified and directed.

M & L for Point Wiring complete with 1100 Volts, FRLSH Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, confirming to IS - 694 drawn through and including Stove enameled metallic conduit of size 25 mm dia medium grade including all accessories fixed on surface, wall, ceiling, roof etc including 1100 Volts, FRLSH Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth dolly for One Light / Fan Point controlled by One flame proof Switch complete all as specified and directed.

Supply & fix exhaust fans flame proof AC single phase 230/240V of size 300mm sweep with louver complete all as specified as directed.

M&L for sub main wiring complete with 2 runs of 4 Sqmm PVC insulated and unsheathed cable with multistranded, FRLS grade copper conductor confirming to IS-649, 1100 volts grade with colour code and drawn through in and including medium grade 25mm dia PVC non metallic rigid conduits and conduit accessories concealed in wall / floors / ceiling etc and connecting terminal ends including 1x 4.0 Sqmm PVC insulated unsheathed copper conductor cable green colour as continuous earth continuity conductor and connecting to earth complete all as directed and specified. Note: Two runs of 4.0 Sqmm copper cable, One run of earth wire of 4.0 Sqmm copper cable and 25mm dia PVC conduit shall be measured and paid as one RM.

M&L for sub main wiring complete with 2 runs of 6 Sqmm PVC Insulated and unsheathed cable with multistranded, FRLS grade copper conductor ISI marked and drawn through and including concealed 25mm dia PVC medium grade non metallic rigid conduit and conduit accessories fixed on walls / floors / ceilings etc and connecting terminal ends including 1x6 Sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly complete all as specified and directed. Note: Two runs of 6.0 Sqmm copper cable, one run of earth wire of 6.0 Sqmm copper cable and 25mm dia PVC conduit shall be measured and paid as one RM.

M&L for sub main wiring complete with 4 runs of 10 Sqmm PVC insulated and unsheathed cable with multistranded, FRLS grade copper conductor ISI marked and drawn through and including 25mm dia PVC medium grade non metallic rigid conduit and conduit accessories fixed on walls / floors / ceilings etc and connecting terminal ends including 2 runs of 10 Sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly complete all as specified and directed. Note: Four runs of 10 Sqmm copper cable, Two runs 10 Sqmm earth wire and 25mm dia PVC conduit shall be measured and paid as one RM.

M&L for sub main wiring complete with 2 runs of 2.5 Sqmm PVC insulated and unsheathed cable with multistranded, FRLS grade copper conductor ISI marked and drawn through and including 25mm dia PVC medium grade non metallic rigid conduit and conduit accessories fixed on walls / floors / ceilings etc and connecting terminal ends including 1x2.5 Sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly complete all as specified and directed. Note:Two runs of 2.5Sqmm copper cable, One runs 2.5 Sqmm earth wire and 25mm dia PVC conduit shall be measured and paid as one RM.

Supply and fixing Distribution board Power line vertical (VTPN) MCCB DB with IP54 protection metal door, 415 volts, suitable copper bus bar each phase 8 way with double door fixed on flush to the wall including making the hole in the wall and fixing the DB including cement work and plastering complete including making cable connections all as specified and directed. Make : LEGRAND/ABB/L&T

Supply and fixing MCCB with thermal magnetic release 415 volts 4 pole 125 Amps capacity and breaking capacity 16 KA complete all as specified and directed.

Supply and fixing MCCB with thermal magnetic release 415 volts 4 pole 63 Amps capacity and breaking capacity 16 KA complete all as specified and directed.

Supply and fixing SPN MCBs distribution board of sheet metal enclosure factory made double door powder coated single pole and neutral with 200 amps rated bus bar 12 way 240 Volts complete all as specified and as directed.

Supply and fixing SPN MCBs distribution board of sheet metal enclosure factory made double door powder coated single pole and neutral with 200 amps rated bus bar 8 way 240 Volts complete all as specified and as directed.

Supply and fix MCB SPN 40 to 63 Amp 240 Volt , 10KA , 'C' curve complete all as specified and directed.

Supply and fix MCB SP 5-32Amps 240 Volts , 10KA , 'C' curve single phase complete all as specified and directed.

S&F High efficient LED Street light fitting 35 watt, with Aluminium pressure Die cast housing parts for long life, High purity PC Fresnel diffuser with silicon gaskets for IP65 Protection, in-built electronic driver pre- wired up to terminal block,Suitable for external pole dia. Up to 35 mm, CRI >70,Temperature range- 0 to 45DegC, Driver efficiency>85%, Power factor>0.95, THD<10%, Colour Temperature- 5700K, Surge protection in CM-3.5KV, 50000 burning hours as per L70 Criteria, Multistage Isolated Constant Current- Constant Voltage Operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard in and including 1.5 Mtr length GI tubing medium grade 25mm dia or suitabl+B137e dia bent to shape with necessary CI clamps, bolts etc for fixing and connecting from ceiling rose to filling with 3 core 1.5 Sqmm insulated copper cable complete all as specified and directed.

Earthing complete with galvanised iron earth plate electrode 600 x 600 x 6mm as earthing lead buried directly in ground vertically to depth not less than 2.25 mtr below GL with the top edge of the plate not less than 1.5 mtr from GL, connected to GI earth lead of 4.0mm dia, by means of bolts & nuts, to GI and connected to earthing test point all as shown in elecrical plate No. 3 of SSR Part-I of 2009* specified or indicated and testing on completion including excavation / earth work in any type of starta, PCC (1:3:6) type C1 earthing chamber pre cast slab 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric (XPM) weight not less than 4 KG/sqm cast iron frame, funnel with wire mesh GI watering pipe of 20 mm bore medium grade and lugs with and including GI earth wire 4 mm dia with GI protection pipe of 15 mm medium grade 7.5 meter long etc complete tested on completion all as specified and directed. Note: 1. Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. Earth resistance shall not exceed 2.0 ohm.

Supply and fix casing caping of size 25mm x 16mm including all accessories like elbow, Tee, Coupler and bends etc complete all as specified and directed.

Supply and installing 300mm width x 50mm depth x 2mm thickness size of perforated hot dipped Galvanised Iron cable tray (Galvanisation thickness not leass than 50 microns) with perforation not more than 17.5% inconenient sections, jointed with connectors, suspended from the ceiling with GI suspenders including GI Bolts & nuts as required acomplete all as specified and directed. Note : 1. All necessary fixing/ connecting arrangements of nut, bolt, MS rod, to be provided by the contractor without any extra payment from department. 2. Quoted rate is to be deemed the charges of necessary boom lift.

Supply and fix Copper Strip 20 x 3 mm placed on insulators (In and including) fixed on walls complete all as specified and directed.

Supply, install, testing and commisioning of five star rated split type Air conditioner complete with indoor and outdoor unit and with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with latest invertor technology with hot & cold having ECO friendely refrigerent gas, copper condenser coil of capacity of 2 TR inculding all fixing arrangement as required at site including copper pipe and control cable and initial filling of regrigerant gas complete all as specified and directed. Make : BLUE STAR/HITACHI/DAIKIN/ CARRIER/ VOLTAS

Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 volts to 250 volts with out put voltage stablized at 230 volts with accuracy of +/- 2.5% and of capacity 5 KVA complete all as specified and directed.

Supply and laying of extra copper pipe with nitrile rubber tubular insulation and copper cable using necessary supports and fastners complete all as specified and directed.

M&L for factory fabricated steel stand suitable for fixing 2 TR AC outdoor unit and fixed complete all as spcified and directed

Making opening/drilling of size 65 mm dia, using heavy duty stone driller/cutter machine in the stone machinry wall for installing spilit type air conditioners and for passing suction and discharge refrigerant pipe lines, drain pipe, cable etc and making good the disturbed surface complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole 20 Amps MCB 'C' curve 10 KA complete all as specified and directed.

M & L for HDPE pipe 25 mm dia fixed to wall on roof complete all as specified and directed.

Sub main wiring complete with 4 runs of 6 Sqmm PVC Insulated and unsheathed cable with multistranded, FRLS grade copper conductor ISI marked and drawn through and including concealed 25mm dia PVC medium grade non metallic rigid conduit and conduit accessories fixed on walls / floors / ceilings etc and connecting terminal ends including 2 runs of 6 Sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly complete all as specified and directed. Note: Four runs of 6.0 Sqmm copper cable, Two runs of earth wire of 6.0 Sqmm copper cable and 25mm dia PVC conduit shall be measured and paid as one RM.

Supply and fixing Distribution board Power line vertical (VTPN) MCCB DB with IP54 protection metal door, 415 volts, suitable copper bus bar each phase 4 way with double door fixed on flush to the wall including making the hole in the wall and fixing the DB including cement work and plastering complete including comprising the following complete all as specified and directed.

Supply, Install, testing & commissioning of silent type Diesel Engine Driven Generating set, fully wired Alternantor AC to give an output of 320 KVA continuously rating at a power factor of 0.8 lagging, 3 phase, 4 wire, 415 volts, 50Hz, 1500 RPM directly coupled with diesel engine water cooled, mounted on common base frame complete with accoustic enclosure (canopy) with latest CPCB norms, fuel line & accessories, control panel showing standard parameters of Engine and Alternator, AMF Panel with control cable, exhaust pipe, fuel tank, PCC foundation work as per manufacturers instructions, anti vibration pads and other standard accessories and comprising of the folllowing, complete all as specified and directed.

(A) Alternator - Standard design alternator capacity of 320 KVA net out put at site after considering derating as per site condition at 0.8 power factor (lagging) 3 Phase, 4 wire, 415 Volts, 50 HZ, 1500 RPM, self excited, self regulated with brushless excitation screen protected drip proof IP23 enclosure, insulation class 'H' directly coupled with diesel engine through flexible coupling. The Alternator shall be suitable for tropical climate and shall conform to BS-5514 / 5000 / IS-3046 as amended upto date. (B) Diesel Engine: Water cooled Diesel Engine suitable for 320 KVA, 4 stroke, 6 cylinder, turbo charged to deliver not less than 386 BHP at 1500 RPM under NTP conditions of BS-5514 and conforming to IS 10002 and ISO 3046, the engine is prime rated with 10% over load capacity for one hour in any 12 continuous hours of operation. The engine shall be provided with electrical starting arrangments and shall give the electrical out put of 320 KVA at 0.8 power factor, 415 volts including standard accessories and comprising of following: - (i) Radiator with lower fan including guard. (ii) Pipe coupling for engine cooling system piping. (iii) Corrossionin hibitor collant. (iv) Paper element filters for fuel, lube oil, bypass. (v) Fly wheel housing and fly wheel. (vi) Engine bearing mechanism in fly wheel housing

(vii) Flexible coupling. (viii) Dry type air cleaners and vaccum indicators (ix) Residential silencers (x) Stainless stell exhust flexible bellows (xi) Motor driven priming pump (xii) Electric starter (xiii) Battery charging indicating.

(xiv) Exhaust piping made out of heavy duty mild steel pipe 'C' class of length 3.5 metres above the building height (height of the building + 3.5 metre) or as per recommendations of OEM to meet CPCB norms inclusive of all accessories and hardware, neccessary support steel structure stack including mineral wool insulation 2 inch thick suitable for 400 degree celcius temperature cladded with aluminium sheet for the entire length of exhaust pipe (xv) Exhaust gas driven turbo charger (xvi) Electronic governor

(xvii) First fill lube oil, coolent and diesel during commissioning and 12 hours testing (xviii) Fuel injection pump (xix) Engine control panel with all accessories and components dispaying the battery voltage and charging rate, water temparature lubricating oil pressure, engine speed, engine hours run, balance of fuel indicator (xx) Safety control (trip and indication) for high water temparature, low lube oil pressure, low and high speed trip (xxi) Common Base frame for engine and alternator made from structural steel channels / beams duly painted (xxii) Battery set of 2 Nos maintainance free type 12 Volts, 180 AH capacity including copper conductor multistranded leads of suitable size and adequate length from starter to battery terminals. Make : Exide/Amron

Note :- Emission Standards for DG Sets (a) The Emission limits of DG Sets upto 320 KVA shall be incorporated as per the latest CPCB norms as published by the Gazette of India New Delhi dated 03 Nov 2022 vide S No 716 Extraordinary part-II - section 3-sub section (i) and emission limits shall come into force from 01 Jul 2023. (b) The emission limits shall be tested through one of the five CPCB approved recognized labs as mentioned below :- (i) Automotive Research Association of India, Pune (Maharashtra). (ii) International Centre for Automotive Technology, Manesar (Haryana). (iii) Indian Oil Corporation, Research and Development Centre, Faridabad (Haryana). (iv) Indian Institute of Petroleum, Dehradun (Uttarakhand). (v) Vehicle Research Development Establishment, Ahmednagar (Maharashtra). (vi) The Cost for incorporation of Emission Standards and testing is included in rate quoted by the contractor.

(C) Accoustic Enclosure (Canopy): Accoustic encloser suitable for 320 KVA DG set made out of 1.6mm thick CRCA sheet duly powder coated painting all as incompliance with latest CPCB norms suitable to reduce noise level to 75 DB measured at 1.0 mtr distance for audible frequencies as per manufacturers specifications and comprissing of following: - (i) Rugged in construction maintainance free and modular design high quality accoustic insulation materials to be used as per IS 8183 for maximum sound absorption, accoustic layers shall be supported with perforated sheets a see through transparent window glass infront of engine panel to provide for monitoring the operation (ii) Emergency stop button at exterior body (iii) Deliverables 75 DB at 1 mtr distance at 75% load under free field conditions (iv) 02 Nos of 10 watt LED lamps for inside illumination.

(D) AMF Panel: Auto Main Failure (AMF) panel board suitable for 320 KVA DG set, Outdoor type CPRI approved factory fabricated made out 3.15mm thick CRCA sheet, free standing, floor mounted, cubicle type, dust and vermin proof, ventilated, weather proof duly power coated painting with siemens grey paint, IP 54 class protection, totally enclosed conformimng to IS 8623, double door with locking arrangement provided with removable hinged front and rear doors for eassy accessibility, internally prewired, copper bus bar of suitable rating including electrical and electronic components / accessories and comprising of following: - (i) Air Curcuit Breaker 630 Amps, 65 KA, 4 pole, 415 volts, 50Hz microprocessor based manually drawout type-02 No's for main supply and DG supply with HRC back up fuses complete with auto mains failure relay to act on main commercial supply to start the DG set and to stop the DG set on restoring of commercial supply working in dual mode and line voltage monitor (LVM) as per OEM specifications.

(F) Civil Work: All civil works including RCC / PCC platform and related to foundations for commissioning of Generator set shall be as per recommendations of the manufacturer. The foundation drawing for DG Set shall be got approved by Engineer-in-Charge before laying of foundation including material required. Note: (a) The contractor shall arrange for artificial load including diesel, coolent and lube oil etc. for 12 hours testing at site are deemed to be included in rate quoted by the contractor. (b) Contrctor shall submit the detailed specification, model No, Make, technical literature and foundation drawing of DG set for approval of Accepting officer. (c) contractor shall submit AMF panel drawing with dimensionS and arrangement of switch gear, matering devices and make/model of switch gear for approval of Accepting officer.

Supply and fix double compression copper chromum plated gland for fixing armoured cable in size 3.5 core 400 Sqmm complete complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying cables / poles foundation / stay assembly and getting out in hard / dense soil complete all as specified and directed.

Returning filling in including spreding leveling watering and well ramming in layer not exceding 25 cm as in soil complete all as specified and directed.

Removing excavated material to a distance not exceding 50 m and depostingwhere directed at a level not exceding 1.5 mtr above the starting point complete all as specified and directed.

Material and labour for Sand cushioning to under ground cable providing with a layer 8cm thick below the cable and 15 cm thick above the cable and punned down to 18 cm complete all as specified and as directed Note: Punned thickness only will be measured for the purpose of payment.

M & L for Un- reinforced pre cast concrete covers class LV type 250mmx 150mmx 40mm size factory made for cable protection complete all as specified and directed.

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 400 Sqmm 3.5 Core including taking up existing old unserviceable LT UG cable complete all as specified and directed.

Supply & laying Synthetic Insulating Mat of size 2.00Mtr x 1.00Mtr x 2.5 mm thick complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 metres below normal ground level with top edge of earth plate not less than 1.5 metres below ground level connected to galvanized iron strip 32 x 6 mm as earting lead upto 7.5 metres or upto test point / connecting pointby means of bolts, nuts, check nuts and washers made out of galvanised iron or steel all as shown in electrical plate No 3 of SSR part I and earth strip protected by galvanized pipe light grade 40 mm bore light grade including necessary earth work and excavation in any type of strata, GI medium grade 20mm bore watering pipe with funnel and wire mesh, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2:4 type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS Hook 6mm dia MS bars etc complete all as specified and directed and testing on completion. Note: 1. Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. GI strip above 7.5m will be measured and paid seperately. 3. Earth resistance shall not exceed 2.0 ohms.

Supply, Install, testing & commissioning of CPRI approved outdoor type LT Panel board suitable for 415 volts, 3 Phase, 4 wire, 50 Hz Power distributon panel of suitable size, pre wired with adequate size of single core PVC insulated FRLS stranded copper conductor cable, control fuses, earthing terminals, lifting hooks, danger notice plate, free standing, front and back openable construction, floor mounting, dust and vermin proof of IP-54 protection as per IS-8623, provision for ventilation, compartmentalised design, hinged type double door with mechanical locking arrangement for each feeder, factory fabricated out of 3.15mm thick CRCA sheet, 7 tank process powder coated painting fixed on and including necessary earth work civil work with PCC 1:3:6 type C2 foundation and comprising of the following switch gear and accessories complete all as specified and directed :- (a) Bus bar chamber of 3 phase and neutral 4 strip 415 volts with 1200 Amps Aluminium strip - 1 set (b) LT air circuit breaker 4 pole 50 KA breaking capacity 800 Amps capacity with manual draw out type microprocessor type-03 Nos (incoming + outgoing) for Aspirate system + Commercial Supply + DG set AMF supply). (c) Three phase volt meter - 01 No. (d) Three phase Ammeter - 01 No.

(e) LED indicator lamp red, yellow, Blue-01 Set (f) Complete internal wiring with suitable copper conductor wires - 01 Lot. (g) Provision of exta space for two more out going feeders suitable for 400 Amps MCCB. Note :- (i) All termination of existing cable should be provided with copper lugs/thimbles and suitable size of glands & rate for the same is deemed to be included in the item

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit / GI pipe or fixed to poles or any other indicated situation for loop earthing etc as required of GI strip 32 x 6 mm complete all as specified and as directed.

Supply, Install, testing & commissioning of CPRI approved outdoor type LT Panel board suitable for 415 volts, 3 Phase, 4 wire, 50 Hz Power distributon panel of suitable size, pre wired with adequate size of single core PVC insulated FRLS stranded copper conductor cable, control fuses, earthing terminals, lifting hooks, danger notice plate, free standing, front and back openable construction, floor mounting, dust and vermin proof of IP-54 protection as per IS-8623, provision for ventilation, compartmentalised design, hinged type double door with mechanical locking arrangement for each feeder, factory fabricated out of 3.15mm thick CRCA sheet, 7 tank process powder coate+B172d painting fixed on and including necessary earth work civil work with PCC 1:3:6 type C2 foundation and comprising of the following switch gear and accessories complete all as specified and directed :- (a) Bus bar chamber of 3 phase and neutral 4 strip 415 volts with 800 Amps copper strip - 1 set

(b) Moulded Case Circuit Breaker 4 pole 50 KA breaking capacity 630 Amps capacity with thermal magnetic trip unit (TMD) - 1 Nos (Incoming) (c) Moulded Case Circuit Breaker 4 pole 36 KA breaking capacity 200 Amps capacity with thermal magnetic trip unit (TMD) -1 Nos (Out going) (d) Moulded Case Circuit Breaker 3 pole 16 KA breaking capacity100 Amps capacity with thermal magnetic trip unit (TMD) - 2 Nos (Out going) (e) Moulded Case Circuit Breaker 3 pole 16 KA breaking capacity 63 Amps capacity with thermal magnetic trip unit (TMD) - 3 Nos (Out going) (f) Moulded Case Circuit Breaker 3 pole 16 KA breaking capacity 40 Amps capacity with thermal magnetic trip unit (TMD) - 5 Nos (Out going) (g) Three phase volt meter - 01 No (h) Three phase Ammeter - 01 No (j) LED Indicator lamp Red, Yellow, Blue - 01 Set (k) Complete internal wiring with suitable copper condutor wires - 1 Lot (l) Provision of extra space for two more out going feeders suitable for 400 Amps MCCB Note : (i) All termination of existing cable should be provided with copper lugs/thimbles and suitable size of glands & rate for the same is deemed to be included in the item

Lucky Enterprises

RAHUL ENTERPRISES

devan enterprises

D NAGI REDDY

Sai Ram Builders