Sanitary work upto first manhole and Finishing of bathrooms for Boys Hostel and Girls Hostel of Medical College Baramulla

Amount

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron/P.V.C P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, incl. 15mm CP brass single hole basin mixer & 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous counter top wash basin size 550x400 mm.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460mm bowl depth 200mm

Providing and fixing 2900x450 mm (or any size) beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder C.P. brass

Providing and fixing PTMT Bottle Trap for Wash basin and sink: Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm min water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality, weighing not less than 88 gms.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of Black/ Grey/Red Color

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing uplasticized PVC connection pipe with brass unions 45 cm length and 15 mm nominal bore

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing, fixing, testing and commissioning of CP brass swan neck sink mixer with wall flange and swinging casted spout complete as required and making good the walls wherever required.

Providing & fixing grab bar in toilets for physically handicapped with non-slip gripping surface complete in all respects, including cutting and making good the wall wherever required.

Providing & fixing 600 mm grab rail in toilets for physically handicapped with non-slip gripping surface complete in all respects, including cutting and making good the wall wherever required.

Supply, fixing, testing and commissioning of storage type automatic electric hot water heater made out of heavy gauge steel jacket finished with rust proof baked-on glossy white enamel paint, inside glass lined heavy gauge steel tank, 25 mm thick polyurethane foam insulation, thermostatically controlled immersion heater with pilot neon lamp, replaceable magnesium anode bar, suitable for 8.0 bar maximum working pressure, cold water inlet and hot water outlet pipe, suitable length of electrical cable and 15 amp 3 pin plug top, non return valve and pressure release valve complete in all respect including testing etc. (Horizontal/Vertical)

a) 25 litres storage capacity

b) 50 litres storage capacity

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe any dia

Providing and fixing 8 mm dia C.P. / S.S. Health faucet with flexible tube upto 1 metre long with holder to European type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing C.P. Brass extension nipple (size 15mm x 50mm) of approved make and quality as per direction of Engineerin- charge.

Providing and applying of 15mm thick cement sand plaster in 1:6 mix (1 cement: 6 fine sand) including stagging/scaffolding for interior plaster and curing complete as per directions of the engineer-in-charge. Including all taxes and material required.

Providing and laying in position cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) grade including curing but excluding the cost of centring and shuttering at all levels as per directions of the engineer-incharge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers, Anti-Skid Joint less) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete as per directions of the engineer-in-charge.In all colours, shades, except White, Ivory, Fume Red Brown

Providing and applying white cement based (Waterproof) putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per directions of the engineer-in-charge. 1 mm average thickness.

P/A waterproof cement priming coat over wall/ ceiling surfaces of approved brand including cost of all materials leads, lifts and carraiges etc upto site of work complete

Wall Painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work incl carraige lifts etc all complete

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Shelves (cast-in-situ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. TMT bars of grade Fe-500D or more

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for Brick masonry in superstructure above plinth level upto floor V level.

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm)

Supply, fixing, testing and commissioning of unplasticized polyvinyl chloride pipes conforming to IS 13592-2013 Type B UV stabilized with rubber ring/click ring or pasted type for soil, waste discharge system inside buildings (fixed with clamps/stays etc) including jointing with rubber seal ring wirh rubber lubricant conforming to IS:5382 in case of grooved socket joints and using solvent cementing, conforming to IS 14182 for sliding socket joints and/or in tandem including all necessary minor fittings as per directions of the engineer-incharge.

a) 110 mm OD Pipes

b) 40 mm OD Pipes

c) 50 mm OD Pipes

Providing and fixing un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC Soil, waste pipes conforming to IS : 14735-1999 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion

i) Coupler 110mm/50mm/40mm

ii) Collar 110mm/50mm/40mm

iii) Single Tee with door 110mm/50mm/40mm

iv) Single Tee without door 110mm/50mm/40mm

v) Bend 87.5° 110mm/50mm/40mm

vi) Reducing Cross Tee 110mm/50mm/40mm

vii) Floor Trap 110mm/50mm/40mm

viii) W. C. Connector 110mm/50mm/40mm

ix) Double Y 110mm/50mm/40mm

x) Eccentric Reducer 110mm/50mm/40mm

xi) Floor Drain 110mm/50mm/40mm

xii) Vent Cowl 110mm/50mm/40mm

xiii) Varaible bend 110mm/50mm/40mm

xiv) Door bend 110mm/50mm/40mm

xv) Cross Tee 110mm/50mm/40mm

xvi) P-Trap 110mm/50mm/40mm

xvii) SS Gratings 110mm/50mm/40mm

xviii) Clean out pipe 100mm dia

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections. 110 mm inlet & 110 mm outlet Long ht

Providing and fixing 125 mm dia, 1 mm thick stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.Of JAQUAR , CERA or equivqlent make.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

PN-16 pipe , 20mm OD(SDR-7.4)

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

PN-16 pipe , 40mm OD(SDR-7.4)

PN-10 pipe , 50mm OD(SDR-11)

PN-10 pipe , 63mm OD(SDR-11)

PN-10 pipe , 75mm OD(SDR-11)

PN-10 pipe , 90mm OD(SDR-11)

Providing and fixing PPR Unions

PPR Union 20mm

PPR Union 25mm

PPR Union 32mm

PPR Union 40mm

PPR Union 50mm

PPR Union 63mm

PPR Union 75mm

PPR Union 90mm

Providing and fixing of brass/bronze lever operated valve of full flow with stainless steel ball (AISI 304 and spindle AISI 410) with setting and gland of superior quality having minimum working pressure of 10 kg/cm². UNIK/Zoloto or equivalent.

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing motorised butterfly valve with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box etc., complete. POLO PLAST/ PESTAN S LINE/UNIK/ZOLOTO 50/65/80/100 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete (Base Support for water tanks)

Providing and fixing uPVC/cPVC/G.I tank nipples of 40/50/63/75mm dia as required and as per directions of the engineer-incharge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil.Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete

100 mm diameter

150 mm diameter

Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround stoneware/ RCC pipes including in bed for pipes to be laid in trenches as per standard details.

a)100 mm diameter

b)150 mm diameter

Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C. top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design. ( excluding cost of cement) Inside size 90x80 cm and 45 cm deep including CI Cover with frame (light duty ) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15 kg): 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Cutting holes up to 15x15 cm in R.C.C. floors/roofs/Beams/Walls for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and laying water proofing treatment in sunken portion of Gutters, WCs, bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying: (Tapecrete of CICO or approved equivalent) (incl. cleaning the surface and removing mulba from the surface ) (a) 1st layer of slurry of cement @ 0.488kg/ Sqm. mixed with water proofing cement compound @ 0.253kg/ Sqm. This layer will be allowed to air cure for 4hours. (b) 2nd layer of slurry of cement @ 0.242kg/ Sqm. mixed with water proofing cement compound @ 0.126 kg/ Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry but excludes cost of cement.

Providing and laying stone Dust blended with cement (10 % ) under sunkun portions of Bathrooms incl. compacting , watering , densifying ,all complete

tariq mohd mir

BHAT TRADERS

Star Structural constructions and company

M/S VALLEY CONSTRUCTIONS