SPECIAL REPAIR OF BLDG NO P-34/01 TO 08 (OR MD ACCN), CONVERSION OF LIGHT EMITTING DIODE BULB INTO INVERTOR LIGHT EMITTING DIODE BULB IN OTHER THAN MD ACCN AND PROVN OF VEHICLE PARKING SHED (NEAR P-20) AT NABHA UNDER GE (S) PATIALA

Amount

'Notes: (i) Please refer Schedule 'A' Notes of tender documents.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

M&L for 15mm thick Cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished complete all as specified and directed Note : Water proofing compound shall be measured and paid saparately under item .

M&L 10mm thick cement plastering in cement mortar 1:6 finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all asspecified and directed.

Material and Labour for exterior painting work including complete removal of existing loose paint layers till plaster level by using jet pressure washer and crack filling up to 3mm by using crack seal & up to 10mm by using textured crack filler. Touch-up by using wall putty with silicon additives followed by application of one coat of truecare exterior primer on walls and Chajjas and applying two coats of modified acrylic smooth emulsion exterior grade with silicon having anti-algal and Dust pickup resistance properties, Material should be applied (Dilution, Recoating period etc..) as per manufacturer instructions by using fully automatic air less spray machine having flow speed of minimum 1ltr per minute and pressure of 3300 PSI. (Ace Suprema). or equivalant. Note-The above Specification is guaranteed for 3 year painting warranty

Note for Ser item No 06 :- The work for shall include the following and the rates quoted by the bidders shall include the same :- (a) Use of Scaffolding, trestles, ladders, cradles etc necessary for execution of work and protective measures. (b) Removing of Nails, making good holes, cracks etc (c) Work in patches and in narrow / widths, bands, cornices, pilasters etc and cutting in edge of line where necessary. (d) Spreading and removing covering to doors, windows, floors, fittings etc to protect them from splashes. (e) Washing floors, cleaning glass, joinery , electric fittings , wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-Charge. (f)Sample patch of 10Sqm be prepared considering all the items of periodical and shall be got approved from GE prior to carrying out further work.

M&L prepration of new plastered or unplastered surface of walls and applying two coats of distemper oil emultion over complete all as specified and directed.

Supplying & applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating on Brick level, SmartCare Damp Block 2K or approved equivalent (For Effloresce treatment), having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per ASTMC1202, crack bridging up to 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI, will be apply on both Positive & Negative side and resist up to 5 Bars of Hydrostatic Pressure. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. After coating sand will be sprinkled on the coating then apply plaster on the coating including all type of scafolding etc as required complete as manufacturer specifications and as specified and directed. Note : Taking down cement plaster and rendering plaster will be measured and paid seperately.

Supply only integral water proofing compound ISI marked, complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces applying three coat of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparing old plastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.

All as per srl item No 13 hereinbefore but n. exc 1.5 sqm each.

S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with single rebate including necessary fixing lugs, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc. complete as specified,size 105x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified and directed. Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item.

S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with double rebate including necessary fixing lugs, lock strike plate, hold fasts ,filling PCC (1:3:6 Co) in chowkhats , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 125x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified. Note :- Disturbed portion of existing floor /wall / tile / plaster etc duing fixing of chowkhats shall be repaired to match with existing finish .Cost of the same will be included in this item

M&L Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm 2nd class hard wood Glazed and skeleton shutters, 2nd class hard wood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed.

S&F Aluminium 200mm anodised, barrel tower bolt of extruded complete all as specified and directed

Aluminium anodised sliding door bolt of size 250mm, stove enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts complete all as specified and as directed.

S&F Aluminium handles 125mm cast type , anodised complete all as specified and directed.

S&F Mild steel butt hinges of size 100mm medium weight cold rolled, complete all as specified and directed.

S&F in repair 300 mm long MS rat tail pattern spring hinge including roller and roller plate, complete all as specified and directed.

S&F Floor door stopper of aluminum alloy body and tongue, anodised, with hard drawn steel spring fixed complete all as specified and as directed.

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete all as specified and directied fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard sectionand fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement complete all as specified and directied.

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beed 20mm size complete all as specified and as directed.

S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directied.

M&l preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer all as specified and directed.

M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises, complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in complete all as specified and directed.

M&L for Ceramic floor tiles of 7 to 8mm thick of size 600 X 600 mm in floor etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in CM (1:4) laid in complete all as specified and directed.

M&L for Non Skid coloured tiles 7 to 8mm thick of size 400 X 400 mm in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in CM (1:4) laid in complete all as specified and directed.

M&L for coloured glazed ceramic tiles 7 to 8 mm thick of size 600 X 300 mm as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes icluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

M&L for taking Up or down steel tubing of size 15mm bore and removal to store complete all as specified and directed.

M&L for taking Up or down steel tubing of size 20mm bore and removal to store complete all as specified and directed.

Supply and laying of 20mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed.

Supply and laying of 25mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed.

S&F in repair mild steel chromium plated 20mm curtain rod with fixing brackets, stops rollerss complete incl fixing brackets, stops etc complete all as specified and directed. Note:- For the purpose of mesurement and payment running length of curtain rod only shall be considered.

S&F 18 mm thick LEAD FREE PVC celuka ply of approved color fixed with screws, slovent cement/adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets including taking down as per manufactured's specification complete all as specified and directed. NOTE: not less than 10kg per sqm

S&F 12 mm thick LEAD FREE PVC celuka ply of approved colour, fixed with screws, slovent cement/adhesive to make wall mount kitchen cabinets back and pull out drawer sides including taking down as per manufactured's specification complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 Kg, complete all as specified and directed.

S&F Paino/continuous hinge of size 30 mm stainless steel complete all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacture's instructions complete all as specified and directied.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150 mm long matt finished complete all as specified and directed.

S&F stainless steel 304 grade wire Basket (avg wait 2.5 to 4 Kg per basket) of pull out type like plain/cup& saucer/bottle/multi purpose/2-3 shelf baskets etc for kitchens of required size complete all as specified and directed.

M&L for dismantling of brick tiles or terracing tiles single layar on roofs complete all as specified and directed.

M&L for Demolition of mud puska and removing on roof any thickness complete all as specified and directed..

M&L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in padding over roof a slope of 1:100 using water proofing compound finish even and smooth without using extra cement complete all as specified and directed.

M&L for the following roof treatment. (a) Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick weight not less than 3.60kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt, fixed as per manufacturer’s instructions complete all as specified and directed. (b) Applying one coat of bituminous primer confirming to IS-3384 @ 0.3 Ltr/Sqm. (c) Applying one coat of aluminium paint over APP membrane @ 0.50 litres per Sqm all as specified and directed. (d) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per square metre including cleaning the surfaces all as directed and specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame atsite as per specification & drawing, complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification and drawing, complete all as specified and directed.

S&F PVC(SWR) Floor trap 75mm plain with CP grating including jointing to wate pipe with solvent cement complete all as specified and directed.

S&F PVC ( SWR) rain water pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete as as pecified including flat iror clamps 25x3mm complete all as specified including taking out old damaged AC rain water pipes, complete all as specified and directed.

S&F PVC (SWR) bends of any radius for 110 mmdia rain water pipes with rubber ring joints a complete all as specified and directed.

S&F Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl 20 mm bore ball brass valves high pressure with polythene float and fly nut all as specified in SSR Part-1, complete all as specified and directed.

S&F 125mm Brass chromium plated shower rose complete all as specified and directed.

S&F in Repair Bib taps( Long nose) for 15 mm dia bore pipe cast copper alloy cromium plated with capstain head screwed down for iron pipe or brass ferrule and fixed complete all as specified and directed..

S&F in repair Brass CP mixer for mixing hot and cold water screwed down for iron pipe 15 mm dia complete all as specified and as directed.

S&F in repair Pillar taps Cast copper alloy fancy type 15mm bore , with capstan heads Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed with long screwed shanks and fly nuts scrrewed for iron pipe and fixed complete all as specified and directed.

S&F in repair angle stop valve(Concealed type) cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipeafter taking down old stop cock of any description complete all as specified and directed.

S&F in repair 20mm Stop valves/ gate valve , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed.

S&F Viterous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, fixed all in repairs, including cutting for or pinning in brackets complete all as specified and directed

S&F Tubular towel rail, CP 20mm dia, 60cm long between flanges fixed in repairs, complete all as specified and directed.

Supply Only low level flushing cistern of PVC 10 ltr capicity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy,screwed both ends , high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed.

S&F viterous china ware wash down water closet Orrisa pattern size 580x440mm white with integral foot rests including connection to traps and to flushing pipe, anti syphonage pipe complete all as specified and directed.

S&F Hard core of broken bricks of gauge n exc. 63 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface complete all as specified and directed.

S&F for PCC (1:3:6), 50mm thick aggregate size 40mm as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement, complete all as specified and directed.

M&L 20mm thick black colure granite Machine cut as in border (Patti) laid over cement screed 15mm thick in CM 1:4 over and jointed with gray cement slurry mixed with pigment including rubbing and polishing complete all as specified and directed.

M&L for machine cut Pre Polished Kota stone slab flooring 20-25mm thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 25mm thick cement concrete type B-0 (12.5mm graded aggregate) complete all as specified and directed.

All as per item No 76 here in before on vertical surfaces as in skirting/dado of size as required at site in CM 1:4 10mm thick but excluding 25mm thick PCC all as directed.

S&F Stainless steel wall mounted kitchen dish plate rack of size 750mm X600mm X 250 mm as described complete all as specified and directed.

S&F PVC enclosed case (cabin type) with cover and looking mirror over it with two shelves in it and fixed with screws on wall, complete all as specified and directed.

S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore complete all as specified and directed

S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, fixed to wall of 110 mm bore complete all as specified and directed.

S&F PVC (SWR) 110 mm vent cowl complete all as specified and directed.

S&F PVC (SWR) 110mm bore Bend complete all as specified and directed.

S&F in repair PVC (SWR) junction double, (double T), equal or unequa 110 mm with parallel branch complete all as specified and as directed.

S&F PVC P & S trap with grating including jointing to waste pipe 110 mm dia fixed complete all as specified and directed.

M&L for demolition of brick work or stone masonry built in cement mortar including all quions, arches, pillers, etc complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in cm 1:4 with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius complete all as specified and directed.

Demolition and breaking up 150mm drain pipes set in cement mortar (salt glazed stoneware/asbestos cement/reinforced) and removal of debris to low lying area to a distance not exceeding 100m, complete all as specified and directed.

M&L for reinforced concrete pipes, class NP2 laid and jointed complete with collars bore in pipes 150mm complete all as specified and directed.

M&L for150mm bore, cement concrete bed 1:3:6 type C2, using 40mm graded stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in deep and getting out in soft/loose soil for foundations, etc or for shafts, wells, cesspits, manholes, pier holes, etc complete all as specified.

Removing excavated material (soil) to a distance not exc 50mm and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soils complete all as specified and directed.

S&F Fe-410 (Gde E-250) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening Note - Removing of old gate fixing new steel gate of hold fast, finish the surface included in this item, complete all as specified and directed.

S&F Coolar stand Joist, channel, angle, or tee sections, fixed independently, without connecting plates, conforming to Fe 410-W (Gde-E-250) quality -A, complete all as specified and directed.

M&L Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams, ceilings and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including cutting grooves in brick /concrete wall and preparation of surfaces to receive finishes complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring, complete all as specified and directed.

M&L for Dismantling wrought iron or mild steel work of any description, complete all as specified and directed.

S&F MS hollow rectangular/square/circular tubes/pipes of Fe410-W(Gde-E-250) Grade as in frame work for roof/rafter/ purline/chajja/trusses /columns /struts etc and like similar items etc. complete all as specified and directed.

M&L for dismantling of asbestos cement sheets [corrugated, semi-corrugated, etc] in roof coverings complete all as specified and directed.

S&F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping complete all as specified and directed.

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits(thickness vary from1.5to2.5mm as required for desired smoothness and levelling of surfaces in two or more layers)by us ingready made wall careputty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed.

M&L for taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L for point wiring with 1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/sockets point/ in ceiling Portion surface conduit wiring to be done, complete all as specified and directed. Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth. (iii) Necessity cutting chasing where ever required shall be part of job & making good the disturbed surfaces shall be part of job.

All as per item No 105 above, but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and directed.

All as per item No 105 above, but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed.

All as per serial item No 105 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and directed.

M&L for Modular switch 1 way 6A, 1 module type all as specified and directed.

M&L for Modular switch 1 way 16A, 1 module type all as specified and directed.

M&L for Modular Socket, 6A - 5 pin 2 module type all as specified and directed.

M&L for Modular Socket 6A/16A - 2/3 pin 2 module type all as specified and directed.

Supply and Fixing LED light fittings 1 x 20 Watt, 220 V, AC decorative box type with driver, holder including LED tubelight connecting up with three core flexible copper conductor cable of size from ceiling rose complete all as specified and directed.

Supply & fix in replacement of LED 10 Watt, 2 feet long, Cool day light with NEO Batten10 W 6500K having high efficiency Cat No. LHEXACP7IN1W010 of Havells or equivalent makes mentioned hereinafter incl necessary electric conection complete all as specified and directed.

Material and labour for modular ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all as specified and directed.

Material and labour for lamp holder modular type, PVC/ polycarbonate type with back plate suitable for 7 to 18 watts complete all as specified and directed.

Supply and fix inverter LED Lamp 9 Watt, complete all as specified and directed.

Supply and fix inverter LED Lamp 15 Watt, complete all as specified and directed.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires 230 Volts including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Material and labour for call bell ding dong AC 230 volt single pole complete all as specified and directed.

Material and labour for Modular Bell push 6A 1 module complete all as specified and directed.

M & L for Fan step regulator, 120W - 1 module complete all as specified and directed.

S&F Energy saving ceiling fans complete with blades, down rod and with all accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM not less than three star rated with brushless direct current motor (BLDC) including taking down complete all as specified and directed. (Note:-Unsv C/Fan will be deposted to MES office).

S&F Exhaust fan 300 mm sweep, metal body type AC single phase 240 V with louver including taking down complete all as specified and directed. Note : (i) Fixing of exhaust Fan on wall with suitable size anchor bolt, cutting wall for making hole suitable for 300 mm sweep exhaust fan, grouting and making good the disturbed surface shall be part of job at no extra cost. (ii) Unsv Exhaust Fan will be deposted to MES office.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep grouting including taking down and making good the disturbed surface shall be part of job at no extra cost, complete all as specified and directed. Note:- Unsv Exhaust Fan will be deposted to MES office.

Supply and fixing Vertical load line type TPN DB, 4 way 415 V, double door as per IS - 8623, IP-54 protection, universal mounting with suitable capacity copper bus bar with nuetral bus bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for accomodate MCCB TPN 100 Amp as incomer and TP&SP MCCB/MCBs as outgoing complete & making necessary electrical connection for incoming and outgoing cables, with copper lugs, crimpped with crimping tool complete all as specified and directed. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing shall be part of job.

S&F in replacement of existing MCCB TPN, 63 Amps, 415 volts, 16 KA complete fixing in DBs including proper thimbles connections complete all as specified and directed.

S&F SPN DB suitable for MCBs of single pole and neutral 8 Way as per IS - 8623, IP-54 protection,double door type with 200 amp rated bus bar complete all as specified and directed. Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) Dismantling of existing sheet metal box will be deposited to MES. (iii) Masonry work to fill the space of iron sheet box will be part of the job. (iv) Energy Meter will be refixed & connected after fixing of new DB. (v) MCB'S shall be fixed with copper wires FRLS 1.5/2.5 Sqmm incl appropriate size of brass/Cooper thimbles. Note :- Existing metal enclosure of SPN DB will be deposited to MES.

Supply and fix in replacement of MCB SP up to 6-32 Amp ('B' Curve) all as specified and directed,complete all as specified and directed.

Supply and fix in replacement of MCB SPN 6-32 Amp ('B' Curve) complete all as specified and directed.

M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x6 sqmm ( line conductor) & 1x6 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed. Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth. (ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size. (iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frame 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I, complete all as specified and directed.

S&F Geyser (water heater) vertical storage type 240 volts, 2000 Watt, water proof IPX-4 Pprotection having adjustable knob for temperature settings, copper cell of 25 Ltr capacity with all accessories such as safety valve, thermostate, NRV, connection piece etc. and incl cost of anchoring arrangement (nut & bolts) to the wall, corded copper electric cable etc incl dismantling of existing geyser complete all as specified and directed. Note:-Unsv Geysers will be deposted to MES office.

Supply and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 Sqmm, 3.5 core laid in trenches /on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified. Note : Only Punned soil shall be measured and paid

Supply and laying GI tube 50 mm light grade as in cable protection pipe including all fittings & taking down / taking out from trench complete all as specified and directed.

M&L for laying of well burnt Brick 23 cm x11.5 cm x7.5 cm for cable protection complete all as specified and directed.

Supply and fix LED inverter Bulb, Cool Day Light, Energy Efficient, Glare Free Soft Light, Power Backup Feature, inbuilt Overcharging Protection, inverter Bulb 7 Watt (CDL) cool day light type with min backup of 3 hrs complete all as specified and directed.

Supply and fix LED inverter Bulb, Cool Day Light, Energy Efficient, Glare Free Soft Light, Power Backup Feature, inbuilt Overcharging Protection, inverter Bulb 9 Watt (CDL) cool day light type with min backup of 3 hrs complete all as specified and directed.

Supply and fix LED inverter Bulb, Cool Day Light, Energy Efficient, Glare Free Soft Light, Power Backup Feature, inbuilt Overcharging Protection, inverter Bulb 12 Watt (CDL) cool day light type with min backup of 3 hrs complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out soft/loose soil, complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws as specified.

M&L for rolled sections as in main and cross beams, hip and jack rafters purlins, where connected to common rafters and running rails and guides for slinding doors, fixed with angle cleats or other connecting plates to Fe-290 (Gde E-165) complete all as specified and directed.

S&F mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections complete all as specified and directed.

Surface excavation n exc 30 cm deep and avg 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed

m/s k.k. construction co. (BID ID -3404103)