8182 PROVN OF TIOLET BLOCK FOR BOYS AND GIRLS CADETS NEAR SPORTS AREA, ADDN/ ALTN OF PORTION OF RHS (GF) OF P-92, ADDN/ALTN TO GENTS AND LADIES TOILET OF COMMUNITY MEDICINE, ADDN/ ALTN TO MUSEUM OF PHARMACOLOGY DEPT, PROVN OF COVERED DRAIN NEAR OFFIC

Amount

Taking down chowkats or frames not exc 1.5 sqm each (without taking off shutters from the frames) and making good disturbed portion including removing unserviceable frames off the premises complete all as specified and directed.

All as per item No 1 here-n-before but exc 1.5 sqm but not exc 4 sqm each.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc. and removing rubbish off the premises complete all as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceable tiles and rubbish off the primises complete all as directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete and removing rubbish off the premises complete all as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removing rubbish off the premises complete all as directed.

Taking up or down carefully steel tubing and connection s including cleaning for refixing or removal from site complete for the following bore :-

(a) 15mm dia bore

(b) 20mm dia bore

Demolition and breaking of drain pipes of 75 to 110mm dia AC /CI/PVC set in cement mortar or adhesive complete including removing from site all as directed.

Dismantling Stone slabs / tiles of any description or thickness, laid ,bedded &pointed in cement mortar in floors, hard standing, apron etc and removal of rubbish out side the MD land all as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting in out hard/ dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / disintegrated rock complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/ dense soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L for loose broken bircks filling of gauge 80 to 150mm in soakage pit complete all as specified and directed.

M & L of hardcore of guage exc 63mmbut n exc. 100 mm, deposited,spread and levelled in layersn exc. 15 cm thick with broken stone or boulder, watered and rolled/rammed to a truesurface complete all as specified and directed.

M & L for plain cement concrete type D2 1:4:8 (using 40mm graded stone aggregates) as in foundations, filling and mass-concrete complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C2 (40mm graded stone aggregates) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete.

M & L for provinding plain cement concrete (1:2:4) B-1 as in copings / bearing course over brick walls etc and like complete all as specified and directed.

M & L for providing cement concrete type A0 (1:1.5:3) using 12.5mm graded stone aggregates as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands and railings upto 60 cm in height, copings water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing.

M & L RCC (1:1.5:3) (nominal mix) type A1 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

All as per item No 24 here-in-before but in columns, pillars, posts etc.

All as per item No 24 here-in-before but in lintel.

All as per item No 24 here-in-before but septic tank/ soak pit slab supported on walls complete all as specified and directed.

All as per item No 24 here-in-before but in precast cover slab for manhole soak well and similar articles and set in CM (1:6) complete including use and wase of formwork complete all as specified and directed.

M & L for brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

M & L for brick work with sub class 'B' bricks in one brick thick honey comb walling built in cement mortar (1:4) complete all as specified and directed.

M & L for precast cement concrete block masonry exceeding 10cm in width with solid blocks of PCC (1:5:8) gde D-5 and setting in CM 1:6 complete all as specified and directed.

M & L for precast cement concrete block masonry not exceeding 10cm in width with solid blocks of PCC (1:5:8) gde D-4 and setting in CM 1:4 complete all as specified and directed.

M & L for 40mm thick damp proof course to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 mixed with liquid WPC as per manufacturer’s instructions including necessary formwork complete all as specified and directed. Note : Liquid WPC shall be measured and paid separately.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus unserviceable bricks and rubbish off the premises complete all as directed.

Cutting chases, pinning in making good to facings where required and pointing in CM 1:4 for consealed water tubing etc complete all as specifed and directed.

Use and waste of formwork to roof beams, lintels and soffits of roof projections etc and similar items including edges complete all as specified and directed.

All as per item No 36 here-in-before but to sides of footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

All as per item No 36 here-in-before but to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

All as per item No 36 here-in-before but soffits of suspended slab such as septic tank slab etc complete all as specified and directed.

S & F II nd class hard wood plain, solid, straight chowkats & frames , wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and as directed.

S & F 2nd class hard wood 35mm thick, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

S & F 35 mm thick Flush shutters, solid core construction, with partical board core and plywood face panels, commercial type on both sides complete all as specified directed by Engr-in-Charge.

S & F factory made wood grain printed (Prelaminated) solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes 19 mm x 19 mm having wall thickness 19 gauge for stiles. MS tube 15mmx 15mm having wall thickness 19 mm gauge for top and bottom rails. MS frame shall be covered with 5mm thick heat moulded prelaminated colour PVC 'C' channel having 5mm thick PVC sheet strip 20mm wide struck inside with solvent cement for stiles and 5mm thick PVC sheet for top rail, lock rail and bottom rail on either side and 10mm (5mm x 2mm) thick, 20mm wide cross PVC sheet as gap insert for top and bottom rail. Paneling of 5mm thick prelaminated colour PVC sheet to be fixed in MS frame welded/sealed to the stiles and rails with 5mm x 30 mm PVC sheet beading and jointed together with solventcement complete all as shown in drg and specified.

S & F Factory made wood grain printed (Prelaminated) solid PVC single door frame of size 50 x 47 mm with a wall thickness of 5mm prelaminated colour sheet reinforced with 19 mm x 19mm MS square tube having wall thickness 19 guage complete all as shown in drg and specifed.

Taking down wooden door shutter and refixing including resecuring or easing and adjusting in the same opening.exc 1.00 but nexc 2.00 sqm each complete all as specified and as directed.

S & F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified and directed.

S & F aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

All as per item No 47 here-in-before but 200mm long.

S & F aluminium anodised handles, fabricated type of size 150 mm complete all as specified and directed.

S & F aluminium alloy sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 300 mm complete all as specified and directed.

S & F aluminium single leaf door on pivots alongwith hydraulic door closer (Aluminium Extruded section), door lock, handles, 5mm thick plain glass in top and 12mm thick prelaminated particle board (both side laminated) in bottom panel, fixed with rubber beading and glazing clips and using powder coated sections as given in 'JINDAL' Catalogue complete all as directed by Engineer-in-Charge.

S & F ventilators / louvers using 5 mm thick x 10 cm wide frosted glass strips inside & stainless steel wire cloth 0.36 mm dia and 1.18 mm width of aperture from outside using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as specified & as directed :- (a) SP- 20048, (b) Glazing clips - 19352

S & F pressed steel door frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate including filling with PCC (1:3:6) type C1complete all as specified and directed.

S & F chimney bars and similar articles conforming to Fe 410-0 or Fe 310-0 for angle iron threshold of door frames complete all as specified and directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails and guides for fixed with angle cleats or other connecting plates confirming to Fe-290 Gde E-165 complete all as specified and directed.

S & F MS framed work such as grills, gratings etc., with ends of bars shouldered and/or riverted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.

S & F framed work as in gates with ornamental and intricate design with ends of bars shouldered and/or riveted con- forming to Fe.290.Gde-E-165 including pintle hinges, stops, hand made sliding bolts etc complete all as specified and directed.

M & L for TMT bar 10mm dia and over cut to length bent to shape reqd incl cranking bending etc complete & binding with MS wire (annealed) not less than 0.9mm dia in reinforcement complete all as specified and directed.

All as per item No 59 here-in-before but 8 to 10mm dia as in stirrups spacers and binders.

M & L for false ceiling with 8mm thick PVC Panels (coloured/ designed) including decorative cornices/moulding of pattern as approved by Engr-in-Charge on and including GI grid frame work consisting Grid& GI main tee 32x24mm , cross tee 25x24mm and angle of walls of size 20x20mm, grid not less than 600x600 mm hung from ceiling using 4mm GI wire suspension spaced at 1.2m c/c on main runners inculding making nitches for light, fan decorative/concealed light fittings and fasteners if required complete all as specified directed by Engr-in-charge.

M & L for 09 mm thick Gypsum ceiling board for ceiling prepainted, perforated finish, 600 x 600 mm in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle hung from ceiling using 4 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M & L for epoxy grouting 75 mm thick for crack filling, voids, and joints in concrete structures by providing deep penetration, shrink free solid mass, strong bonding inside the cracks and excellent resistance to honey combing and chemicals including necessary formwork and securing the formwork or any scafolding etc required for the process complete all as specified and directed.

M & L for 100mm thick plain cement concrete type C-2 (1:3:6) using 40mm graded stone aggregate in sub base / levelling course above existing course to accommodate floor / nahani traps etc. complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in plinth protection/paving finished even and fair all as specified and directed.

M & L for coloured digital non-skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all specified and directed.

All as per item No 68 here-in-before but area of each tile exc 0.11 Sqm and n exc 0.18 Sqm.

All as per item No 68 here-in-before but area of each tile exc 0.6 Sqm and n exc 0.11 Sqm.

M & L for coloured designer glazed ceramic tiles of size 300 x 450 x 7mm / 300 x 600 x 7mm thick as in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L (light shade) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

All as per item No 72 here-in-before but on vertical surfaces such as in skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick backing coat in CM 1:4 all as specified and as directed by Engr-in-Charge.

S & F 20mm thick granite (of any type) work (table rubbed and polished) for wall lining(veneering to wall) 12mm thick in cement mortar(1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM (1:6) complete all as specifed and directed.

M & L 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M & L for 25mm thick plain cement concrete (1:2:4) type B0 using 12.5mm graded aggregate as in floor of septic tank and finishing the surface even and smooth with using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM 1:6 over brick / conc wall surfaces trowelled to even & smooth w/o using extra cement for internal wall complete all as specified and directed.

All as as per item No 77 here-in-before but in CM 1:4 mixed with liquid WPC as per manufacturer's instruction for external wall complete. Note: Liquied WPC shall be measured and paid separately.

All as as per item No 77 here-in-before but 10mm thick in CM 1:3 as in ceiling complete.

All as per item No 77 here-in-before but 15mm thick in CM (1:3) on fair faces of PCC block/ concrete surfaces and finish the surface even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound.

M & L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

All as per item No 82 here-in-before but on ceiling.

M & L preparation of newly plastered surfaces and applying two coats of acrylic emulsion paint over 2mm thick wall care putty on walls all as spd and directed.

Complete removal of existing treatment and M&L for applying 2mm thick wall care putty and applying two coats of acrylic emulsion paint on walls all as spd and directed.

M & L preparation of newly pastered or unplatered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over 2 mm thick wall care putty complete all as specified and directed.

M & L for preparation of old plastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M & L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M & L for preparation of new wooden surface of any description and applying two coats of synthetic enamel paint over one coat of pink primer, over 10cm in width or girth complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc primer complete all as specifed and directed.

S & F GI tubing "medium grade" galvanized with all fittings and fixed complete to walls and ceilinng or laid in floors etc complete all as specified and directed for the following bore :-

15mm dia

20mm dia

M & L PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls / laid in floors complete all as specified and directed.

All as per item No 93 here-in-before but 75mm bore.

M & L PVC (SWR) bends of 110 mm bore of any radius complete all as specified and directed.

All as per item No 95 here-in-before but75mm bore.

M & L 110mm PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed.

S & F 110mm bore PVC (SWR) branch piece (single) Y) equal or unequal complete all as specified and directed.

M & L 110mm PVC (SWR) vent cowl complete all as specified and directed.

S & F 100mm bore sand cast Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

All as per item No 100 here-in-before but 75mm bore.

S & F 100mm CI Bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed.

All as per item No 102 here-in-before but 75mm bore.

S & F 100mm bore CI Bends (any radius) with duck’s foot or heel rest fitted with oval access door complete all as specified and directed.

S & F 100mm bore CI branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S & F cast iron cowl 75mm dia complete all as specified and directed.

S & F rotational moulded polyethylene water storage tank double layered 1000 ltr capacity (Cylinderical vertical with closed top) with tank nipple and 20mm bore ball brass valve hoisted and fixed in position complete all as specified and directed.

S & F 20mm bore gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F 15mm bore chromium plated bib cock as per Cat No T3505A1 of Make Parryware or equivalent model from the make list given in the PS.

S & F in repairs 15 mm bore chromium plated fancy type angle cock with wall flange consealed type as per Cat No. F2002201 of Cera or equivalent model from the make list given in the PS.

S & F 15 mm bore chromium plated 2 way bib cock with wall flange confirming to CAT No. F2002161 of " Cera" or equivalent model from the make list given in the PS.

S & F 15 mm bore pillar taps chromium plated, fancy type as per Cat No. F1005101 Ruby of Cera or equivalent model from the make list given in the PS.

S & F 15mm bore pillar taps chromium plated, fancy type swan neck spout (left) and aerator as per Cat No F2002104 of cera or equivalent model from the make list given in the PS.

S & F 15mm bore chromium plated concealed stop cock as per Cat No T3511A1 of Make Parryware or equivalent model from the make list given in the PS.

S & F 15mm bore stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and directed.

S & F CP towel rail 20 mm dia and 600 mm long including brackets conforming to CAT No. ACN-1111N of "Jaquar" or or equivalent model from the make list given in the PS.

S & F in repairs Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S & F in repairs CP toilet paper holder conforming to CAT No. F5001109 of Cera or equivalent model from the make list given in the PS.

S & F Health faucet conforming to CAT No. ALD-573 of make "Jaquar" or equivalent model from the make list given in the PS.

S & F in repairs, brass CP soap dish conforming to CAT No. F5007106 of Cera or equivalent model from the make list given in the PS.

S & F brass chromium plated shower rose 125mm size fitted to steel pipe or union complete all as specified and directed.

S & F Vitreous China Urinal, Half stall type, white excluding push cock, flush pipe and waste pipe etc complete all as specified and directed.

S & F vitreous china wash down water closet (Pedestal Pattern) model Elite (White) Cat No C0297 of Make Parryware or equivalent model from the specidired make with S Trap and seat cover complete all as specified and directed.

S & F vitreous china Counter Top Basins including brass chromium plated 32mm bore waste coupling (Self-Rimming) model Mini Oval C0438 White of Make Parryware or equivalent model from the make list given in the PS.

S & F 15mm bore 450 mm long PVC connection pipe complete all as specified and directed.

S & F 32mm bore PVC waste pipe complete all as specified and directed.

S & F CI Nahani trap 75mm dia with SS grating with or without hole incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S & F SGSW gully trap of size 150mm x 100mm square or round mouthed, type P incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S & F in repairs 75mm dia PVC floor trap with steel grating including jointing with solvent cement complete all as spd and directed.

S & F in repairs vitreous china wash down water closet pan, 'Pedestal' coloured , including fixing bolts etc including PVC seat cover white flat bottom and CP or aluminium anodised hinging devices etc. complete all as specified and directed.

Supply and fixing PVC Valve less syphonic action type flushing cistern 10 litres capacity low level white ,with inlet ball valve float and handle including brackets complete all as specified and directed.

S & F in repairs vitreous china white Single piece WC (S or P trap) with UF soft close seat cover, hinges, size 655 x 370 x 770 mm, as per Cat No. S1021109 of Cera or equivalent model from the make list given in the PS.

S & F oval shaped coloured vitreous china WHB table top Colonia snow white, fancy type of overall size 595 x 380 mm, cat No 7751 of cera or equivalent model from the make list given in the PS including 32 mm CP waste coupling, PVC waste pipe etc complete, including granite slab counter of black colour as approved and of size 1.20mtr x 0.60 mtr includingrounding edges cutting nitches rounding edges etc complete, horizontally supported by 01 No of 35 mm thick cuddappa stone slab one side mirror polished complete all as specified and directed by Engr-in-Charge.

M & L for 150mm bore reinforced concrete pipes, class NP2, laid and jointed with collars laid in trenches and jointed as specified complete all as specified and directed.

All as per item No 136 here-in-before but 200mm bore.

M & L for PCC 1:4:8 type D2 using 40mm graded agg as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore pipe complete all as specifed and directed..

All as per item No 138 here-in-before but for 200mm bore pipe.

M & L for Cutting into existing manholes for connecting new drains of 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

S & F in repairs steel grating round of 100mm size for nahani/ floor trap including jointing complete all as specified and directed.

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimumweight 60gms) complete all as specified and directed.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unserviceable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through duly Casing Caping on wall /roof ISI marked with PVC boxes of suitable size including Modular cover and frame for mounting modular switches/ sockets/ regulators etc and making good the disturbed surfaces to match with existing finishes and including 1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly including dismantling old u/s existing wiring complete with all fittings and fixtures all as specified for the following :

(a) One light/fan point controlled by one, one way switch

(b) One 3 pin 5 A socket outlet point controlled by one No one way switch on same board

(c) One 3pin 5 A socket outlet point controlled by one No one way switch on independent board

All as per Item No. 146 here-in-before but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through duly concealed conduits in wall /roof/ floor along with suitable feetings, with MS sunken boxes of 1.6 mm thick, of suitable size including Modular cover plate and frame for housing modular switches sockets etc along with1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for the following :

(a) One light/fan point controlled by one, one way switch

(b) One 3 pin 5 A socket outlet point controlled by one No one way switch on same board

(c) One 3pin 5 A socket outlet point controlled by one No one way switch on independent board

S & F Modular Switch single pole, one way 6 Amp all as specified.

S & F modular socket outlet 2/3 pin 6 amps, multipurpose 2 module 230 Volts, single pole one way complete all as specified.

S & F modular switch 16A SP one - way 230V white ivory finish complete all as specified and directed.

S & F modular socket outlet 2/3 pin 16 amps, multipurpose 2 module 230 Volts, single pole one way suitable for plug tops, complete all as specified and directed.

S & F for ceiling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for MCB DB SPN sheet metal enclosure 8 way with 200 amps rated bus bar double door, fixed on wall making good to disturbed surfaces and connecting with existing cable including dismantling old u/s MCB DB complete all as specified.

S & F MCB DB 4 way, double door, with 200 amp rated busbar 240 V, SPN all as specified and directed by Engineer in charge.

S & F for MCB DB, SPN, sheet metal enclosure, 2 way, single door, fixed on wall making good to disturbed surfaces, and connecting with existing cable complete all as specified and directed.

S & F for MCB double pole of rated capacity 32 amps, 240 volts breaking capacity 10 KA, C-curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified and as directed.

M & L for Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4 sqmm in and including PVC casing caping and accessories complete all as directed by Engineer-in-Charge. Note:- Making good of disturbed surfaces will be done by contractor without any claims. (Note :- 3 runs of 4 Sqmm conductor and one run of casing caping shall be measured as one unit length.)

M & L for Sub main wiring complete with two single core 2.5 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 2.5 sqmm in and including PVC conduits and accessories complete all as specified. Note:- Making good of disturbed surfaces will be done by contractor without any claims. (Note :- 3 runs of 2.5 Sqmm conductor and one run of PVC Conduit shall be measured as one unit length.)

Supply and fix LED Tube light fittings wall mounted, 18 W LED 6500K with Opal white Poly Carbonate diffuser provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector Conforming to Cat Part No. BLRB DB 118 & BLRB18 W CW LED Make :- Bajaj or equivalent model from the make list given in the PS.

S & F LED energy efficient Security light fitting 30 Watt LED, pressure die cast aluminium housing in heat resistant glass covered with IP 65 Protection and including GI pipe as required length and size with fixing accessories complete all as specified and directed. Cat Part No- BCLST 30W LED I Make - Bajaj or equivalent model from the make list given in the PS.

S & F LED post top lantern 35 W New energy saving, environmental friendly, along life aesthetically designed with symmentrical light distribution, spun aluminium landscape lumminaire with high power LEDs as light source and IP - 65 protecton of make HAVELLS conforming to cat part no RUBYPT35WLED757PSYMTOPC or equivalent model from the make list given in the PS.

S & F round recessed mounted 12 watt LED downlighter with aluminum housing finshed in premium white powder coating with robust electronics for erratic power conditions of white/neutral white color temperature etc, prewired and all accessories complete all as specified and directed Make - Cat part No. EDGEPRORDDLR12WLED857S of Havells or equivalent model from the make list given in the PS.

S&F LED light fitting 10 watt complete in all respect having high luminaire, integrated LED channel with white acrylic cover of 10W cap.Cat Part No BCLSB10WH of Bajaj or equivalent model from the make list given in the PS.

S & F LED light fittings 2'x2', 42 watts environmental friendly, new genereation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source 230 volts with all accessories internally pre wired and necessary mounting arrangements, complete all as specified. Make :- Make HAVELLS Cat part No. PLUTONEO2X2PLR42WLED840S 42 W or equivalent model from the make list given in the PS.

S & F exhaust fan of sweep 300mm with louver heavy duty single phase suitable for 230 volts 50 HZ,1400 rpm and connecting up complete including provision of 3 core flexible cord from ceiling rose to connector of fan with cable of suitable size. Make :- Bajaj or equivalent model from the make list given in the PS.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core.

M & L for Reinforced concrete pipes of dia 100 mm 2 nos half round (for bottom and top ) and before laying excavated area shall be leveling all as specified and directed

M & L for GI Tube light grade gavanised with all fittings laid in trenches of size 50 mm

Suma Construction