CERTAIN REPAIR TO BR WORKS TO VARIOUS UNITS AT NARIAN NADPUR AREA AND OTHER LOCATION UNDER AGE BR DETT-A OF GE 862 EWS

Amount

Taking down cement plaster on brick walls or concrete surface etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. Note :- The cost includes any thickness found during execution increased due overleaping of n no of layers of plaster, tiles, mosaic finish without any cost to govt exchequer.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level and removal of debris from site, complete all as specified and directed. Note:- Demolition includes PCC/ floor finishes such as kota stone/ floors tiles of any description. No extra cost to be borne by the Govt exchequer for any of the above.

Demolition of cement concrete (unreinforced) in any position not otherwise specifically provided for including removing of debis outside MoD land, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles, complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) exc 1.5 Sqm but n. exc. 4.0 Sqm each and removing from site, complete all as specified and directed. Note:- The rate includes making good to disturbed surfaces w/o any extra cost to Govt.

All as per item Ser No 5 but n.exc 1.50 Sqm, complete all as specified and directed.

Taking down door shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 sqm and refixing in the same opening, complete all as specified and directed.

All as per item Ser No 7 but n.exc 1.00 Sqm, complete all as specified and directed.

Dismantling of cast iron or PVC upto 100mm dia, jointed in cement mortar in any position, complete all as specified and directed by Engineer -in - Charge.

Hacking out old broken glass (any thickness size, quality or description from wooden or steel frames glazed with putty / beads, complete all as specified and directed.

Dismantling structural steel work as in framed trusses n. exc 10.00 mtr span, complete all as specified and directed.

Dismantling structural steel work of any description not otherwise provided, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge and thickness including nainital or similar pattern as in roof covering including ridges, complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work, complete all as specified and directed.

Dismantling of timber fillets, rails, posts, rafters purlin etc under 40 Sqm cm in section, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4 , complete all as specified and directed.

Description all as per srl item no. 16 here-in-before but except bricks.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

Description all as per srl item no. 19 here-in-before but except stone, complete all as specified and directed.

M&L for precast plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in bond stones set in cement mortar 1:6complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone and dressing of face beds with maximum depression on face from straight edge held against the dressed surface on sand stone n.exc 20mm, complete all as specified and directed.

M&L for rendering 15 mm thick on concrete surface / brick surface on wall in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork and at any height and sie where plaster is to be executed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar (1:6), finished surface even and smooth without using extra cement, complete all as specified and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork and at any height and sie where plaster is to be executed.

M&L for rendering 05 mm thick in cement mortar 1:3 on concrete surface of ceiling/facia, finished surface even and smooth without using extra cement, complete all as specifed and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork and at any height and sie where plaster is to be executed.

M&L for rendering 20 mm thick on stone walls other than fair faces in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed. Note:- No extra cost cost shall be claimed by contractor in respect of formwork and at any height and sie where plaster is to be executed.

M&L for providing 75mm cement concrete, type C-1, 1:3:6, (using 20mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1, (using 20 mm graded crushed stone aggregates) as in coping to path, edging, benching and the like including form work, complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-1, (using 20 mm graded crushed stone aggregates) as in surface channel and drains, complete all as specified and directed.

M & L for 25 mm thick plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in leveling course to floors or roof etc, finishing cement concrete surface even and fair for receiving floor finish, complete all as specified and directed.

M & L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:3, finished surface even and fair for receiving tiles as in dado/skirting, complete all as specified and directed.

M&L for 18-20mm thick Machine cut kota stone slab(mirror polished) (area of each slab n. exc 0.27 Sqm except space constraint) as in flooring, laid and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including machine cutting to make it square or rectangular, rubbing and cutting and polishing to achieve mirror finish, laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Cutting and grinding to existing kota stone flooring including minor repairs and polishing upto mirror finish, complete all as specified and directed.

M&L for 19mm thick granite stone slab (of any type) work (table rubbed and polished) in cooking platforms, in steps, pillars, window cills, jambs etc, laid over 15mm thick bedding in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite slab, rounding edges etc after dismantling of old unserviceable granite stone slab of any size, complete all as specified and directed.

M&L for vitrified tiles (dual shade including border) of size 600x 600 and 08 to 10mm thick (premium quality) as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed.

All as per item ser No 36 but in vertical surfaces, complete all as specified and as directed.

M&L for Vitrified Ceramic tiles double charged 8 to 10 mm thick of approved colour polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, complete all as specified and directed.

All as per item ser No 38 but in vertical surfaces, complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300x600 x7mm thick, (premium quality) in dual pattern on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and as directed. Note:- (i) No extra cost shall be born by govt. in respect of shade, pattern, texture, highlighter tilesand labour factor. (ii) Size and pattern as approved by Engr-in-Charge.

S&F in repair fancy type curtain rod powder coated 25mm dia (of approved colour and design) including bracket holder with end stop, complete all as specified and directed by Engineer-in-Charge

S&F in repair steel rolling shutter 1.25 mm thick with ball bearing, as specified including top cover, anchoring rod, hasp and stapple, guiding rail and one shop coat of primer, erected in position as indicated complete push/pull or manual type including forming mortice holes for fixing of shutter with PCC 1;3:6, type C-0, using 12.5mm graded crushed stone aggregates, complete all as specifed and directed.

S&F for pressed steel door frames of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including a shop coat of zinc chrome primer including back filling with PCC 1:3:6, type C-1, using 20mm graded stone aggregates, complete all as specified and directed.

S&F for pressed steel door frames of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including a shop coat of zinc chrome primer including back filling with PCC 1:3:6, type C-1, using 20mm graded stone aggregates, complete all as specified and directed.

S&F for factory made 35 mm thick 2nd class hard wood plain frame pannelled shutters (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face verering on both faces. The sizes of rail and style as per IS-1003 part kiling seasoned, complete all as specified and directed.

S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed.

S & F of 300mm MS, ordinary rat tail rod pattern springs including roller and roller plate (ISI marked), complete as specified and directed

S & F of 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane, complete all as specified and directed.

S& F for galvanised mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperature 1.18m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed.

S& F in repair for stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18m and fixed with tinned tacks, or galvinsed wire staples including cutting, welding etc for steel window / ventilators, complete all as specified and directed.

M & L for powder coated (customised design heavy duty) aluminium frame of any colour (thickness of powder coating not less than 50 micron) for doors, windows, ventilation, partition frames, other sections for shutters of door window, ventilators, partition with one or more rebates channel for sliding shutters, grilll etc including joining cleats for fixing etc, complete all as specified and directed.

M & L for anodised aluminium (customised design heavy duty) for doors, windows, ventilators, partition frames, other sections for shutters of doors, windows, ventilators, partitions with one or more rebates channel for sliding shutters, grilll etc including joining cleats for fixing etc, complete all as specified and directed.

S&F for rubber gasket of size for fixing aluminum door/ window/ ventilator shutters, complete all as specified and directed.

S&F of 5mm thick solid PVC sheet coloured as in panel to aluminium door / shutter/ partition, complete all as specified and directed. Note:- Design and colour as approved by Engr-in-Charge.

S&F Powder coated aluminum American handle cast type 200mm long for doors (ISI marked), complete all as specified and directed.

S&F anodised aluminum handle cast type 100mm long collapsible type (ISI marked), complete all as sepcified and directed.

S&F anodised aluminum american handle cast type 200mm long for door (ISI marked), complete all as sepcified and directed.

S&F anodised aluminum powder coated handle cast type 125mm long (ISI marked), complete all as sepcified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled (ISI marked), complete all as specified and directed.

S & F of 100 mm long stainless steel butt hinges, medium weight (ISI marked), complete all as specified and directed.

S&F Powder coated aluminum barrel tower bolts 200mm long of extruded section and fixed (ISI marked), complete all as specified and directed.

S & F of 75 mm long extruded anodised aluminium alloy butt hinges (ISI marked) in old or new position, complete all as specified and directed.

S&F door closer hydraulically regulated, aluminium (extruded section body) designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg (ISI Marked), Complete all as specified and directed.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed (ISI Marked), complete all as specified and directed.

M&L for aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, (ISI Marked), complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 200 mm long of extruded section (ISI marked), complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 100 mm long of extruded section (ISI marked), complete all as specified and directed.

S&F for aluminium powder coated barrel tower bolts 100 mm long of extruded section (ISI marked), complete all as specified and directed.

S&F aluminum alloy wire cloth , 0.45 mm nominal dia of wire and avg width of aperture 1.40mm and fixed with aluminum stapples , complete all as sepcified and directed.

S & F for brass mortice lock vertical type 100 mm long with 4 levers (ISI marked) in old or new position , complete all as specified and directed.

S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane in old or new leaf, complete all as specified and directed.

M&L for taking down old aluminium shutters and refixing in the same opening after necessary repairing including replacement of all necessary fittings, complete all as sepcified and directed.

complete remova of existing water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed by Engr-in-Charge:- (i) Taking down/removing existing treatment and cleaning properly with wire brushing etc, rabish off from the premishes (ii) 10mm thick plastering on roof surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturers instructions (iii) after drying concrete surfaces and apply a coat of bituminous primer @ 0.40 Kg/Sqm on the prepared surface of roof (iv) After the primed surface has dried, apply a coat of hoat blown bitumen 85/25 or equivalent viscosity grade @ 1.2 Kg /Sqm of the surfaces etc complete. (v) Laying unrolled over the bitumen coated surfaces polymeric water proofing membrane, of approved make standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction. (vi) Applying a coat of hot air blown grade bitumen of grade 85 / 25 @ 0.5 Kg / sqm duly sanded over polymeric membrane complete. Note :- Rate of WPC will be included in the quoted rate.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240, complete all as specified and directed.

Erection and fixing only steel work in roof trusses including special shape washers et. Complete using using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240, complete all as specified and directed by Engineer-In-Charge. Note: Old Steel retrieve from dismantling shall be re-use.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc. conforming to Gde Fe-290 E-165, complete all as specified and directed.

S&F of mild steel bolts exc. 5 cm and not exc. 10 cm in length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

S&F of (plain or chequered) channels, square cut or notched (oridinary and counter sunk) forming holes, without any attatchment, complete all as specified and directed.

M&L for framing for partition/ cladding by using stainless steel of different size sections and shapes as per ground requirement of reqd shape (Curve or Plain ) (Gde 304 ISI marked) for fixing of boarding using clamps nut bolts using seamless welding buffing in such a way that no joint is visible, complete all as specified and directed by Eng-in-Charge .

S&F for Pre-painted galvalume aluminium zinc coated GI based high rib profile pattern steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof as directed by GE fixed with self tapping screws including side end lap as per manufacturer's instructions including dismantling of old sheet any type, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coated GI based high rib profile pattern steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof bent to a curve of any radius as directed by GE fixed with self tapping screws including side end lap as per manufacturer's instructions, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions including dismantling of old sheet any type, complete all as specified and directed.

Taking down carefully old roof sheet of any description and re-fixing after denting including providing with self tapping screws, complete all as specified and directed.

S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per instructions including dismantling of existing board etc, complete all as specified and directed.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including dismantling of existing board, complete all as specified and directed.

Taking down carefully of old ceiling board of any description and re- fixing after repair of ceiling board and frame, complete all as specified and as directed. Note:- Contractor shall store the item carefully for re-using.

M&L for 15 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down existing GI tubes complete all as specifed and directed.

M&L for 20 mm bore galvanized iron tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors including taking down existing GI tubes complete all as specifed and directed.

S&F in repair 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed.

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in new or old position, complete all as sepcified and directed.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed. Note:- The water tank shall be double layered IS marked duly embosed on face and weight as per IS specification.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old unserviceable tank, complete all as specifed and directed. Note:- The water tank shall be double layered IS marked duly embosed on face and weight as per IS specification.

S&F in repair for vitreous china wash hand basin white, flat back, size 550x400mm size including pedestal, cutting for and pinning ends of brackets or erecting stand including PVC connection and waste pipe, complete all as specified and directed.

S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, 32mm bore PVC flush pipe and handle including brackets, complete all as specified and directed.

Fixing only Flushing cistern after repairing the old one retrieved from repair work, complete all as specified and directed.

S&F in repair viterous China urinal half stall type white including CP spreader holding screws , waste pipe etc, complete all as specified and directed.

S&F in repair Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified and directed.

S&F in repair for viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) and inlcuding set of CP jet with PVC pipe of superior quality, complete all as specified and directed.

S&F in repair water closet pedestal pattern, white colour with soft seat cover and twin flushing cistern (as approved by Engineer-in-charge), complete all as specifed. Make: Cera cat part no. EWC S1012135 (soft seat cover B15002 & Twin flush cistern 2205/BT Cruse)/ Jaquar cat part no. LYS-WHT-38751S250UFSMZ / Kohler white cat part no. K-21924X-S-WK.

S&F in repair vitreous China white coloured, counter top wash hand basin, oval type, white, size 665x495mm including cutting for and pinning in, complete all as specified and directed. Make: Cera cat part no. WHB-S2031032/ Jaquar cat part no. ASC-WHT-87701/ Kohler 25531W.

S & F in repairs for sink without draining board made out of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410mm x 330 mm x 160mm complete all as specified and directed.

S & F in repair for 15mm bore brass chromium plated centre hole basin mixer with round spout including 450mm long PVC pipe with brass nuts without pop up, complete all as specified and directed. Make: Cera cat part no. F1015451/ Jaquar cat part no. CON 167KNB/ Kohler 16231D-40.

S & F in repair for 15mm bore brass chromium plated wall mixer with connection to the over head shower arrangement, with 115mm long bend pipe on upper side, connecting legs & wall flanges, complete all as specified and directed. Make: Cera cat part no. F1015401/ Jaquar cat part no. CON 273KNUPR/ Kohler 98755 W-Y-CP.

S&F in repair for 15mm bore wall mixer with telephonic bath shower arrangement with connecting legs, wall flanges & wall bracket for hand shower, complete all as specified and directed. Make: Cera cat part no. F1015414/ Jaquar cat part no. CON-267KN/ Kohler 19561D.

S&F in repair telephonic hand shower 100mm round shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system including 15mm bore braided hose for telephonic hand shower, complete all as specified and directed. Make: Cera cat part no. F7030101/ Jaquar cat part no. HSH1937/ Kohler 12861NZZ-CP.

S&F in repair 15mm bore angular stop cock with wall flange, complete all as specified and directed. Make: Cera cat part no. F1015201/ Jaquar cat part no. CON-059KN/ Kohler K801541N.

S&F in repair for 15mm bore pillar taps, cast copper alloy, with capstan heads, brass chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed. Make:- Cera/ Jaquar/ Kohler

S&F in repair self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader, complete all as specified and directed. Make:- Cera/ Jaquar/ Kohler

S&F in repair for 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed. Make: Cera cat part no. F1015151/ Jaquar cat part no. CON-037KN/ Kohler 160931N.

S&F in repair for 15mm bore long body bib tap cast copper alloy with capstan head chromium plated, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed. Make: Cera cat part no. F1015151/ Jaquar cat part no. CON-107KN/ Kohler 160931N.

S&F in repair PVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer suitable for basin mixer, complete all as specified and directed. Make:- Jaquar cat part no. ALD-803AB/ Kohler/ Cera

S&F in repair PVC connection 15mm bore 450 mm long Braided Hose with two 15 mm Nut, & Rubber washer without nipple, complete all as specified and directed. Make: Cera cat part no. F8070402/ Jaquar cat part no. ALD-805B/ Kohler

S&F repair for PVC connection pipe 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F in repair Hand shower ( health faucet ) with 8mm dia 1.2 meter long flexible braided chromium plated tube with wall hook, complete all as sepcified and directed. Make: Cera cat part no. F8030103/ Jaquar cat part no. ALD-573/ Kohler 981001N.

S&F in repair for glass shelf assembly 550mm long with chromium plated bracket guard and rainling, complete all as specified and directed. Make: Cera cat part no. F5001114/ Jaquar cat part no. ACNAQN 7771/ Kohler K12158-BN.

S&F in repair for soap dish holder, complete all as specified and directed. Make: Cera cat part no. F5002106/ Jaquar cat part no. ACN-1131N/ Kohler 1216T0.

S & F in repair towel ring square with round flange, complete as specified and directed. Make: Cera cat part no. F5002105/ Jaquar cat part no. CAN-1121N/ Kohler SS-304.

S & F in repair Toilet paper roll holder, complete as specified and directed by Engr-in-Charge. Make: Cera cat part no. F5001109/ Jaquar cat part no. ACN-1155S/ Kohler K-5633IN-CP.

S & F in repairs towel rack 600mm long without lower hanger but with three hooks, complete all as specifed and directed. Make: Cera cat part no. F5003101/ Jaquar cat part no. ACN-1181FHS/ Kohler SS304.

S & F in repair corner glass shelf with tempered glass, with chromium plated rails and bracket, complete all as specified and directed by Engr in Charge. Make: Cera cat part no. F5005101/ Jaquar cat part no. ACN-1173/ Kohler KEA18846CH.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink (Min weight 45 to 60 gms), complete all as sepcified and directed.

S&F in repair for 32 mm bore waste coupling, chromium plated, full threaded with 80 mm long including washers, complete all as sepcified and directed.

S&F in repair 15mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as sepcified and directed.

S&F in repair 20mm dia Ball valve high pressure of PTMT with epoxy coated, aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as sepcified and directed.

S&F in repair PVC 'P' or 'S' trap 110 mm bore (SWR) fixed and jointed, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints fixed to walls with MS clamps of suitable size, complete all as specified and directed.

S & F in repairs for PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints fixed to walls with MS clamps of suitable size, complete all as specified and directed.

S & F in repairs PVC (SWR) bends of any radius with oval access door of 110mm dia complete all as specified and directed.

S & F in repairs PVC (SWR) bends of any radius with oval access door of 75mm dia complete all as specified and directed.

M & L in repair for 75 mm dia floor trap, with grating including jointing to waste pipe with solvent cement, complete all as specified and directed.

S & F PVC (SWR) bends of any radius with oval access door of 110mm dia fixing with solvent cement, complete all as specified and directed.

S&F in repair for PVC (SWR) junction double (single T) of size 110mm bore jointing with solvent cement, complete all as specified and directed.

S&F in repair for PVC (SWR) reducer 110mm to 75mm bore jointing with solvent cement, complete all as specified and directed.

S&F PVC (SWR) bend any radius of 75mm bore, complete all as specified and directed.

M&L for preparation of preprimed steel or iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old or new surfaces including removal of old treatment and applying a thin layer of plaster of parris to give a uniform finish, complete all as specified and directed.

M&L for preparation of old or new surfaces including removal of old treatment and applying a thin layer up to 2 mm thick of putty to give a uniform finish, complete all as specified and directed.

M&L for Cornice with plaster of paris of appropriet design (as approved by Engr-in-Charge) as in corners, complete all as specified and directed.

M&L for complete removal of existing treatment on wall/ceiling surface including cornices and chajjas etc and applying two coats of exterior emulsion weather coat paint (as approved by Engr-in-Charge) after preparation of old or new surface, complete all as directed and as approved.

M & L for preparation of new plastered surfaces of walls/ ceilings and applying two coats of plastic emulsion paint of any shade as approved by Engr-in-Charge over a coat of primer, complete all as specified and directed .

M&L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer including preparation of surface, complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applying one coat of oil bound distemper, complete all as specified and directed.

M&L for preparation of new plastered and unplastered wall surfcace and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L for preparation of old plastered wall surfcace and applying one coats of cement base paint, complete all as specified and directed.

M & L for preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

M & L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M & L for preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down aluminium partition with board / PVC sheet of any description with aluminium / iron mongry, stoppers, cleats etc, complete all as specified and directed.

S&F floor door stopper (overall length of cover plate 140mm) of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in door, complete all as specified and directed.

S&F steel locking bolts with mild steel electo galvanised plate and bright bolt not less than 10mm dia and 100mm long, complete all as specified and directed.

S&F in repair 100mm bore cast iron 'P' or 'S' trap, complete all as specified and directed.

NATIONAL TRADING COMPANY (BID ID -3223103)

CHAND CONSTRUCTION CO (BID ID -3221750)

M/S SURINDER PAL (BID ID -3217044)