SPL REPAIR TO FRONT FACADE RENOVATION OF TOILETS AND ALLIED WKS AT BAYONET AUDITORIUM AT THE INF SCHOOL UNDER GE MIS MHOW

Amount

Taking down shuters of any description nexc 1 sqm each and removing from site complete all as specified and as directed.

Taking down shuters of any description exc 1 sqm but n.exe 2 sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area n. exc 1.5 sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area exc 1.5 but nexc 4.0 sqm each complete all as specified and as directed.

S&F pressed steel door frames of size 105x60mm, made of 1.25mm thick sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified as directed

S&F Mild steel angle or flat iron, small articles such as hold fast , brackets, straps, cleats, etc for door/window chowkats including two coats of red oxide primer complete all as specified and as directed.

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in bed blocks of hold fast, etc complete all as specified and as directed.

S&F 35mm thick factory made 2nd class hard wood plain, framed pannelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board wiyh commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of plain 5mm plain colour PVC sheet reinforced with ms square tube, with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed.

M&L for preparation of new wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed.

S&F in repairs galvanised steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed.

SS&F in repairs fabricating coloured powder coated aluminium frame work,door shutter ,windows , ventilators, partisions with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified and directed.

S&F in repairs aluminium coloured power coated window and ventilator shutters, sliding type without sash bar alu section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all as specified and directed.

S&F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed/Glass and one shutter wire mesh) with following specification complete all as specified and as directed by Engineer-in-charge:- (i) Windows frame of cross section 101mm x 44mm (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm (iii) Sliding shutter frame of cross section 40 x 18mm (iv) 4 mm thick glass superior quality. (Min) (v) LDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos. (Min) (vii) Sliding rollers per shutter - 04 Nos. (Min) (viii) Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. Note- (a)Thickness of Aluminium Section shall be minimum 2 to 3mm (Final Thickness and Cross Section of Aluminium section of higher size without any extra cost shall be approved Engineer in Charge as per Site requirement (b) Drawing /size of window shall be provided by Engineer in Charge during execution of work as per site requirement.

S&F in repairs aluminium coloured power coated door shutters, aluminium section weighing min 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. .

S&F sheet glass ordinary quality 4mm thick and glazing with fixing to Aluminium frame with aluminium beading in squares. not exc 0.5 Sqm each complete all as specified and as directed.

S&F in repairs aluminium (extructed section) Door closer hydraulically regulated, desingnatin No. 3, universal type, suitable for door shutter and fixed complete all as specified and directed.

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

Hacking out old broken glass (any tickness size ,quality or description) from wooden frame or stone etc and S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty or wooden/Aluminium beading in square not exceeding 0.50 sqm in each panes complete all as specified and directed.

S&F 100 mm Butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section complete all as specified and directed.

S&F aluminum alloy handles fabricated anodised of 150 mm long complete all as specified and directed.

S&F in repairs 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring and rubber piece in floor, etc complete all as specified and directed.

S&F in repairs prelaminated particle board 18/19mm thick interior grade, prelaminated on one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame works as in cupboard shutter / cupboard shelves, pelmet, with and including external teak wood lipping 6mm thick and 18/19mm wide fixed with nails on edges complete all as specified and directed.

S&F in repairs 25 mm dia mild steel chromium plated drappery curtain rod with fixing bracket complete all as specified and directed .

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quions ,arcches , pillars etc complete all as specified and as directed.

M&L for brick work in CM ( 1:6 ) with using flyash berick modular size straight or curved on plan exceeding 6m mean radius complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of wall/ concrete surfaces finish even and fair complete all as specified and directed.

M&L for applying two coats of 1st Quality oil emulsion distember over new prepared surface of wall with putty complete all as specified and directed. Note:- Putty shall be measured and paid seperately

M&L for preparation of new plastered surfaces of walls and applying two coat of Acrylic Smooth exterior paint of required shade (@ 1.67 ltr/10 sqm) over over a coat of primer(@ 2.20 kg/10 sqm) same make base all as specified and directed. Make Asian- Apex or Make/Brand as specified in Particular Specification.

M&L for preparation of old painted surfaces of wood/wood based materials exc 10cm width or girth and applying two coat of synthetic enamel paint as directed and specified.

All as per item No. 35.00 above but on steel surfaces. complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying and applying two coat of Acrylic Smooth exterior paint of required shade (@ 1.67 ltr/10 sqm) over over a coat of primer(@ 2.20 kg/10 sqm) same make base white cement based putty (where it is required in patches)all as specified and directed. Make Asian- Apex or Or Make/Brand as specified in Particular Specification. Note:- Putty shall be measured and paid seperately

M&L for preparation of newly plaster surface of wall and and apply 2mm thick cement base wall care putty in two coat (each coat not less than 1mm) over a coat of primer on walls and two coat of paint surface finished even and smooth with sand paper complete all as specified and directed. Note- Putty shall be measured separately.

M&L for 2mm thick wall care cement putty on wall complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick (below or above ground level) complete including removal of debries out side MD land all as specified and as directed .

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone crushed stone aggregate as in sub base, levelling course, etc complete all as specified and as directed.

M&L for PCC1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified and directed

M&L for 75mm thick cement concrete 1:3:6 type C1, with using 20mm graded stone aggregate as in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and as directed.

Dismantling of floor, hearth , or wall tiling including cement mortar bedding (but not backing) and rubbish of the primeses complete all as specified and directed.

M&L for scratch free, doubly charged, vitrified ceramic tiles 9 to 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1: 6 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300x200x7-8mm thick as on vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10 mm thick backing coat on fair faces of brick work in CM (1:4) complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300x450/7-8mm thick as on vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10 mm thick backing coat on fair faces of brick work in CM (1:4) complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified and as directed.

M&L for machine cut kota stone slab in flooring 18-20mm thick of size not less than 595x595 mm as in floor and laid over and including 15mm thick screed bed in CM 1:6 & set jointed and pointed cement mixed with pigment to match the shade of slab including rubbing and laid over and including and polishing complete all as specified and as directed.

M&L for machine cut kota stone( ellow colour) slab in flooring 18-20mm thick of size not less than 595x595 as in floor and laid over and including 15mm thick screed bed in CM 1:6 & set jointed and pointed cement mixed with pigment to match the shade of slab including rubbing and laid over and including and polishing complete all as specified and as directed.

M&L for 16-18 mm thick Black granite slab of approved quality of any size bedded and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over and including 15 mm thick screed bed in CM (1:4) including granite polish to be done by mechanical grinder and moulding edges complete all as specified and directed.

M&L for Grinding of old kota stone /marble mirror polishing inc wax complete all as specified and directed.

S&F in repairs Rotational moulded Polyethylene water storage tank 5000 liters capacity (cylidrical vertical with closed top) of two layer hoisted and fixed in position all as specified in SSR part I complete all as specified and as directed.

S&F in repairs Rotational moulded Polyethylene water storage tank 1000 liters capacity (cylidrical vertical with closed top) of two layer hoisted and fixed in position all as specified in SSR part I complete all as specified and as directed.

Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

All as per item No 57.00 above but 20mm bore.

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc complete all as specified and as directed.

All as per item No 59.00 above but 20mm bore.

S&F in repairs 15mm bore bib taps chromium plated with crutch or butterfly handle ,screwed down , screwed for iron pipes or brass ferrule complete all as specified and directed.

S&F in repairs CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts fixed in 15 mm bore pipes complete all as specified and directed.

S&F in repairs CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified and directed.

S&F in repairs fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed.

S&F in repairs CP toilet paper holder complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes& inc seat cover complete all as specified and as directed.

S&F in repairs PVC valve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed.

S&F in repairs health faucet with flexible pipe of one mtr length including wall hook for EWC complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin white flat back, size 550x400 mm including bracket but excluding taps ,waste pipes , chain and plug etc complete all as specified and directed.

S&F in repairs vitreous china wash basin white (oval shaped under counter) of size 550 x 400mm including 32mm brass CP waste coupling complete all as specified and as directed .

S&F in repairs PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed.

S&F in repairs vitreous china urinal bowl urinal flat back, size of 465x355x265mm white (min)with grating and union for discharge pipe, urinal spreader with waste pipe and all fiting for urinal.complete all as specified and as directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450 mm long complete all as specified and as directed.

S&F in repairs PVC waste pipe for urinal/wash basin/ sink pipe 32mm bore 65cm long complete all as specified and as directed.

S&F in repairs brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets etc as in repair complete all as specified and directed.

S&F in repairs 15mm bore ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed. ( Min Weight 15mm-142 gms) complete all as specified and as directed.

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.

S&F mild steel Hollow Section work in tubular trussles, purlins, rafter, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified and as directed.

S&F mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified and as directed.

M&L for preparation of newly steel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or Or Make/Brand as specified in Particular Specification complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed

S&F Gypsum Board 12mm thick Seamless ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre on GI frame work for seamless ceiling comprising of GI perimeter chennel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylone sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm susoended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with clips of 10.5mm fixed to the intermediate channel at 457mm centre to centre inluding finishing the joint of face board with specially formulatted jointing compound and 48 mm wide fibre tape to provide seamless finish Ceiling shall be sealed at joints and finished with jointing compound etc complete including finishing the exposed surfaces of false ceiling with two coats of plastic emulsion paint over a coat of primer complete all as specified and directed. Note: Placing of false ceilling is to be carried out upto 5.00m height in Classrooms.The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary arrangement work etc required at site.

M&L for Exposed metal frame ceiling with 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and as directed

M&L for complete repairing sunken floor by providing water proofing treatment to sunken floor surfaces of RCC slab with the following specifications complete all as specified and directed :- (a) Provide PCC 1:1.5:3 type A0 using 12.5mm graded stone aggregate in slope of average thickness 50mm on sunken floor slab mixed with and including integral water proofing compound manufactured by Dr FIXIT or other equivalent as approved, and finished the surface even & smooth without using extra cement. (b) Rendering 15mm thick in CM 1:3 mixed with & including integral water proofing compound on sunken floor and sides of (Vertical surface) sunken portion. (c) Applying surfaces with bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm on sunken surfaces of floor & wall and provide necessary connections to soil/waste pipe from WC/Nahanni trap etc including demolition ,cutting holes and making good the disturbed surface as per existing complete all as specified and as directed. (d) Applying two coats of tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane. (e) Laying 3 mm thick APP modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method. Note : Top floor Area shall be measured for payment.

M&L for providing and fixing aluminium composite sheet cladding using 4mm thick sheet of exterior grade consisting of 3mm core of polyethylene sandwiched between two skins of aluminium alloy of grade AA3105 with 0.5mm each on both sides with outer surface in desired colour coating of PVDF coating finished surface to be factory protected with self adhesive peel off foil tested to withstand at least 6 months exposure to local weathering conditions.The composite sheet cut and bent to shaped profiles as required it, including perimeter extrusions base frame (size 25x38x1.4mm) aluminium tube, PVC fastner nut & bolt required for installation as per approved architect elevation drawing & details . Aluminium composite cladding sheet to be approved by architect including sealing joints with silicon (Wacker WS /Dow corning 789) approved make with backer rod to make it air tight with (ACP make - Aludecore/Alstrong/Alstone Or Make/Brand as specified in Particular Specification)

M&L for preparing old iron surface two coat of aluminium paint upto height 6.0 meter on space frame (measured on the basis of bottom /base area)

S&F polycarbonate sheet Transparent thermoplastic 4 mm thick with carbonatestrong quality fixed to existing frame work with nut bolts as in dome fixed b/w iron frame work with screws or nuts bolts complete all as specified and directed. Note:-The contractor shall make adequate arrangement for scaffolding etc and ensure safety of the labour.

M&L for 100mm thick in nominal mix of PCC (1:4:8) using 40 mm graded stone aggregate with approved quality of stone metal, clean coarse sand including Mixing, laying, placing and vibrating with plate vibrator as in foundation or bases of interlocking paver block filling complete all as specified and directed.

M&L for sand filling under floor including waterring and consolidaion complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block (glossy finish) of M-35 Gde of approved shape, size and colour conforming to IS 15658-2006 and including joints filled with sand complete all as specified and as directed.

S&F factory made 25 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free, water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws including necessary Locking arrangement complete all as specified and as directed. Note-:(a)Colour/Texture Style of Door/Prelam Sheet shall be approved by GE (b)Test certificate from original Manufactuer shall be provided before incorporation in the work site.

S&F factory made 100% solid WPC (Wood polymer composite) Door frame 90mm X 45mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade), calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/borer proof, water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-charge. Note-:(a)Colour/Texture Style of Door/Prelam Sheet shall be approved by GE (b)Test certificate from original Manufactuer shall be provided before incorporation in the work site.

S&F 12 mm thick frosted toughned glass fixed on patch hinges/pivot for smooth functioning in door shutter inc stainless steel handle of 8 inches long anfd mortice locking arrangement complete all as specified and directed

S&F 18 mm thick factory made PVC sheet one side pre-laminated sheet ktichen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed.

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as per specified and directed.

S&F Bitumen blown any grade, applied hot,two coats, to concrete surfaces at the rateof 1.50 Kg per Sqm per coat complete all as per specified and directed.

M&L for 10 mm thick rendering in CM 1:3 with WPC @ 3% on fair faces of brick work or concrete surface finished even & smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for Brushing with neat cement slurry @ 3 Kg per Sqm area mixed with integral water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for preparation of surfaces for applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete all as specified and directed

M&L for stainless steel railing (Grade 304) chomium plated finished heavey duty inc all fixing arrangement complete and fixed in an poisition complete all as specified and directed

S&F in repairs urinal sensor fitted including all fittings etc complete all as specified and directed

S&F in repairs 5 mm thick high pressure compact laminate (HPCL) minimum density 700-850 kg/Cum, HPCL sheet are providing higher endurance and spectacular design for walls facade and enhance the over all stability of facade structure inc all fittings. Note:-The quoted rates are inclusive of repair work at any height up to 18.00 m.

S&F in repairs Solid PVC Wall Lining/panelling consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F in repairs 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc.

Taking down exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC FRLSH concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches and blank plates, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- (a) One light point controlled by one switch

(b) One Exhaust fan point controlled by one switch

(c) One 5amps socket out let point controlled by one switch on same board with other switches.

All as per item No 109.00 above but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch.

S&F Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified and directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified and directed.

S&F Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified and directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite three terminal complete all as specified and directed.

S&Fin repair/replacement of lamp holder,PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F Highly efficient LED Bulbs, 10 watts in B-22 cap complete all as specified and directed. Make Bajaj / Havells / Wipro /Crompton Or Make/Brand as specified in Particular Specification.

S&F in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WH / Wipro /Crompton Or Make/Brand as specified in Particular Specification.

S&F in repairs integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH / Wipro /Crompton Or Make/Brand as specified in Particular Specification.

S&F in repairs MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F Exhaust fan 300 mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model: Ventil Air-DX white /Bajaj/Crompton Or Make/Brand as specified in Particular Specification.

vikas traders (BID ID -3395793)