REPAIR/REPLACEMENT OF LEAKAGE WATER SUPPLY PIPE LINES AND ALLIED WORKS REGN A AT BIKANER MIL STN UNDER GE(N) BIKANER

Amount

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation etc or for laying of cables, pipes etc and getting out in soft/loose soil completed all as specified and directed by Engineer-in-Charge. Note for item No1 to 88:- (i) All items considered in work for repair and maitenance at Mil Station Bikaner and ASCON NODES are located at different locations about 200 KM far way from Bikaner city.The cost for repair and maint works will be deemed to included in quoted rates. (ii) All the leakage of water supply pipe lines complaints shall be rectified by the contractor within 12 hrs from the launch of complaint time.If contractor fail to rectify the above said complaint in given time period then a penalty @ Rs 500/day will be recovered from contractor agaist the each job. (iii) All necessary T&P and vehicles for transpotation shall be provided by contractor.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil completed all as specified and directed by Engineer-in-Charge.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point completed all as specified and directed by Engineer-in-Charge.

M&L cutting/dismantling of PCC hardstanding / WBM road with soling & premix carpet of any description for repair/replacement of water supply pipe lines and disposal of debris & rubbish to a distance exc 250m but not exc 500m and making good the same with & including plain cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as existing depth complete all as specified & directed.

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 50 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. ( Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 80 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 100 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 150 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 200 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 250 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soilexcluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 450 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 80mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 100mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed.

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 150mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of jointexcluding necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.Note: Dewatering measured and paid seperattely under relevent items of Sch A

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 200mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint excluding necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 250mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint excluding necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 450mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 500mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

M&L repair to existing leaking run lead joint of CI/DI pipe or fittings of 600mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed. (Note: Dewatering measured and paid seperattely under relevent items of Sch A)

Taking out old damage/broken pipes from trenches & Supply , laying , jointing ,testing and commissioning of DI pipe of size 450 mm bore with spigot and socketed ends centrifugally cast (spun) class K-9 confirming to IS-8329/2000(latest revision ) suitable for push on joint (rubber gaskets) duly ISI marked , complete all as specified and directed by Engr-in-Charge. (Note :- Laying,testing and commissioning , CI fittings/specials, joints ,dewatering by means of JCB or pump and excavation & earth work shall be measured and paid for separately under relevent items.)

All as item No. 20.00 above but 250mm bore.

All as item No. 20.00 above but 200mm bore.

All as item No. 20.00 above but 150mm bore.

All as item No. 20.00 above but 100mm bore.

All as item No. 20.00 above but 80 mm bore.

M&L galvanized steel water tubing medium grade of 15mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 15mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 15mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 15mm bore, complete all as specified and directed.

M&L galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 20mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 20mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 20mm bore, complete all as specified and directed.

M&L galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 25mm bore, complete all as specified and directed. ( Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, fixed to walls and ceilings or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 25mm bore, complete all as specified and directed.

M&L galvanized steel water tubing medium grade of 40mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 40mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 50mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 50mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 80mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 80mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 100mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 100mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

M&L galvanized steel water tubing medium grade of 150mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 150mm bore, complete all as specified and directed. (Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.)

Supply and fixing Cast iron fittings (ISI marked) upto 150 mm bore such as bends (any type, radius & angle), Tapers any type (straight, bend, increasing, decreasing or double socket etc), Tee pieces, single branch, “Y” junction, double branch, cross (all sockets or socket & spigot), collars, caps & plugs suitable for spigot & socketed pipes, complete, fixed in repairs, all as specified & directed. (Note :- (Earth work & lead joints will be paid & measured separately respective item of Sch) & Joints shall be measured and paid for separately.)

Supply and fixing Cast iron fittings (ISI marked) 200 mm to 300 mm bore such as bends (any type, radius & angle), Tapers any type (straight, bend, increasing, decreasing or double socket etc), Tee pieces, single branch, “Y” junction, double branch, cross (all sockets or socket & spigot), collars, caps & plugs suitable for spigot & socketed pipes, complete, fixed in repairs, all as specified & directed. (Note :- (Earth work & lead joints will be paid & measured separately respective item of Sch) & Joints shall be measured and paid for separately.)

Supply and fixing Cast iron fittings (ISI marked) 450 mm to 600 mm bore such as bends (any type, radius & angle), Tapers any type (straight, bend, increasing, decreasing or double socket etc), Tee pieces, single branch, “Y” junction, double branch, cross (all sockets or socket & spigot), collars, caps & plugs suitable for spigot & socketed pipes, complete, fixed in repairs, all as specified & directed. Note :- (Earth work & lead joints will be paid & measured separately respective item of Sch) & Joints shall be measured and paid for separately.

M&L run lead joint for 80 mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 100mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 150mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 200mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 250mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 300/350 mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 450mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 500mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L run lead joint for 600mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 80mm bore GI/DI water pipe line including drilling and welding of 15/20mm GI socket and necessary rubber insertion, nut, bolts & washers complete all as specified & directed.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 100 to 150mm bore GI/DI water pipe line including drilling and welding of 15/20mm GI socket and necessary rubber insertion, nut, bolts & washers complete all as specified & directed.

S&F 15mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 15mm bore, complete all as specified & directed. .

S&F 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete all as specified & directed. .

S&F 25mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 25mm bore,complete all as specified & directed. .

S&F 40mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 40 mm bore, complete all as specified & directed. .

S&F 50mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 50 mm bore,complete all as specified & directed. .

M&L repair to unserviceable sluice valve of size 80mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified and directed.

M&L repair to unserviceable sluice valve of size 100mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve,complete all as specified & directed.

M&L repair to unserviceable sluice valve of size 150mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified & directed.

M&L repair to unserviceable sluice valve of size 200mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified & directed.

M&L repair to unserviceable sluice valve of size 250mm/300mm/350mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified & directed.

M&L repair to unserviceable sluice valve of size 450mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified & directed.

M&L repair to unserviceable sluice valve of size 500/600mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 200 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 200 mm bore, complete all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 250 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 200 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 450mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 200 mm bore, complete all as specified & directed.

Supply and fixing non return valve (NRV) of size 150mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve, complete all as specified & directed.

Supply and fixing non return valve (NRV) of size 200mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve, complete all as specified & directed.

Material and labour construction of brick masonary valve pit chamber of size 900x 900 x 600 mm (Internal dimension) using sub class ‘B’ bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation,brick masanary with sub class bricks 23 cm build in cement mortor with 1:6 , plastering of 10 cm thickness internally and 15 cm externally(1:4) cement mortor and below grond level PCC with 1:2:4 type B2 using 20mm grade stone aggregate ,coping 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys , painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necesarry excavation , returning & filling& removing of surplus soil etc complete all as specified and as directed by the Engineer in charge.

Material and labour construction of brick masonary valve pit chamber of size 1500x1500x1500 mm (Internal dimension) using sub class ‘B’ bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation,brick masanary with sub class bricks 23 cm build in cement mortor with 1:6 , plastering of 10 cm thickness internally and 15 cm externally(1:4) cement mortor and below grond level PCC with 1:2:4 type B2 using 20mm grade stone aggregate ,coping 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys , painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necesarry excavation , returning & filling& removing of surplus soil etc complete all as specified and as directed by the Engineer in charge.

Supply and fixing in replacement cast iron Air release valve with two air outlets ,80 mm dia bore and fixing up in 450 mm dia bore cast iron water supply mains ,complete all as specified & directed.

Supply and fixing in replacement cast iron Air release valve with two air outlets ,100 mm dia bore and fixing up in 500 mm dia bore cast iron water supply mains, complete all as specified & directed.

Supply and fixing in replacement cast iron Air release valve with two air outlets ,100 mm dia bore and fixing up in 600 mm dia bore cast iron water supply mains, complete all as specified & directed.

Dewatering from trenches and taking out of mude etc with the help of JCB or mud pump as required at site and taking out of broken/cracked pipe 450 /500/600mm bore including excavation, returning & filling, removing soil and making good disturbed surface on both side complete, all as specified & directed by Engineer-in-Charge.

All as per item No. 76 here in before but suitable for 250mm /200 mm bore

All as per item No. 76 here in before but suitable for 150mm /100 mm/ 80m bore

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-15, suitable for 500/600 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

Supply & fixing or laying CPVC pipes SDR 11 & plain CPVC SDR11 fittings in trenches or on wall or roof of 50 mm bore dia complete all as specified by Engineer -in charge.

Supply & fixing or laying CPVC schedule 80 pipes & plain CPVC shedule 80 fittings in trenches or on wall or roof of 62.5 mm bore dia complete all as specified by Engineer -in charge.

Supply & fixing or laying CPVC schedule 80 pipes & plain CPVC shedule 80 fittings in trenches or on wall or roof of 75 mm bore dia complete all as specified by Engineer -in charge.

Supply & fixing or laying CPVC schedule 80 pipes & plain CPVC shedule 80 fittings in trenches or on wall or roof of 90/100 mm bore dia complete all as specified by Engineer -in charge.

S&F stop valves cast copper alloy screwed down ,high pressure ,with cruch or butterfly handle ,screwed both side ends for iron pipes or for unions of size 15 mm bore complete all as spoecified and directed.

S&F stop valves cast copper alloy screwed down ,high pressure ,with cruch or butterfly handle ,screwed both side ends for iron pipes or for unions of size 20 mm bore complete all as spoecified and directed.

S&F stop valves cast copper alloy screwed down ,high pressure ,with cruch or butterfly handle ,screwed both side ends for iron pipes or for unions of size 25mm bore complete all as spoecified and directed.

S&F ball brass valve high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule of size 20 mm bore complete all as specified and directed.

S&F ball brass valve high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule of size 25 mm bore complete all as specified and directed.

M/S SIDHU CONSTRUCTION COMPANY

RAJENDER ENTERPRISES

m/s gaurav enterprises

NATIONAL ASSOCIATES

SUBHAM ENTERPRISES

Jetharam Ramchander