CERTAIN B/R REPAIR WORKS INCLUDING FLOORING, TILING, PLASTERING SANITARY FITTING, JOINERY WORK AND OTHER CONNECTED WORK IN ZONE A OF NORTH AREA UNDER GE NASIRABAD.

Amount

Taking down cement or cement lime plaster from stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15mm thick in CM (1:6) on stone masonry surfaces wall finished even and smooth without using extra cement or surface other than fair face of brick-work or on one side of lathing complete all as specified and directed.

M & L for rendering 10mm thick in CM (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM (1:4) on brick/concrete surface mixed with water proofing compound @ 3% by weight of cement & surface fair and even complete all as specified & directed. NOTE :- WPC will be measured and paid separately

M&L for rough cast plaster over & including10mm thick rendering in cement mortar (1:4) on stone/brick masonary wall surface complete all as specified & directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of putty 1 mm thick (Birla/JK) complete all as specified & directed.

M&L for prepartion of new plastered or unplastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

M & L for preparation of newly plaster surfaces of wall & applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surface and applying two coats of weather proof acrylic emulsion paint over a coat of emulsion wall primer all as per manufactures instructions complete all as specified and directed. Make :- Asian, Apex and Berger (Weather coat all Guard) or equivalent as approved by GE

Dismantling floor, hearth or wall tiles including cement mortar and rubbish off the premises, complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floor complete all as specified and directed.

M & L for non-skid ceramic coloured tiles (joint free), 7 to 8 mm thick ( square/rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in CM (1:6) complete all as specified and directed.

All as per Sl item no 12.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set & jointed in neat slurry and pointed in white cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in CM 1:4 complete all as specified and directed.

M & L for non-skid ceramic coloured tiles (joint free), 7 to 8 mm thick ( square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in CM (1:6) complete all as specified and directed.

M & L for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces of wall such as dados, skirtings etc set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tile over and including 10mm thick screed plaster in CM (1:4) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring of size 550mm x 550mm 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over & including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

M&L for Kota stone slab 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing in riser of steps, skirting, dado and pillar laid over & including cement screed 10mm thick in CM (1:4) complete all as specified & directed.

Demolition of cement concrete (unreinforced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of brick/stone masonry built in cement or cement lime mortar in any description complete all as specified and directed.

M&L for stone walling of random rubble, uncoursed, well bonded, bedded & solidly hearted, built in CM (1:6) complete all as specified and directed.

M & L for brick work with fly ash bricks, straight or curved on plan to any radius, in half brick thick wall built in CM 1:4 complete all as specified and directed.

M & L for brickwork with fly ash bricks, old size, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site complete all as specified and directed

M & L for rolled mild steel work angle iron (40x40x6mm) as in door frame (Chowkhats) including provn of 10mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-210 Gde E-165 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed

S & F second class HW Hollock/Bansum/Sal 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

S & F second class HW Hollock/Bansum/Sal, 35 mm thick, glazed and skeleton shutters, factory made open rebated (Three panels)and prepare to receive glass, gauge etc without sash bar, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR Part-I, section 8 clause 8.24(a) Member shall be kiln seasoned & chemically pressure treated complete all as specified and directed.

S&F factory made PVC solid frame of size 50mmx47mm made out of 5mm prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. square tube and fixing in opening as per specification & drawing on page 160 of SSR-2010 complete all as specified and directed.

S & F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick, (styles) with 2 raised panel design with 2mm thick moulded prelaminated PVC sheet on front face & 2mm thick plain colour PVC sheet on back face, and fixing in the frame at site as per specification and drawings on page 161 of SSR (Part - II) 2020 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth applying two coats of synthetic enamel paint (1st grade) over a coat of red oxide primer complete all as specified.

M&L for preparing the new wooden surface of any description over 10 cm width or girth & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer complete all as specified & directed.

S & F in repair steel window/ventilator factory made, made out of MS hollow section 79mmx39mmx1.6mm thick frame with double shutters (Glazed & wire gauge shutters) made out of 'Z' section using flush butt welding & tenon riveting all as per IS 1038 / 83, dobby hinges shall be provided to both shutters. Locking arrangements as per sample approved by GE, provided with knob, 10mm MS square bars in grills, 'Z' section handle 100mm sized & 150mm long hook & eye welded to frame & shutter, four nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fasts and making good in PCC 1:2:4 type B-1 including preparation of surfaces & applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed

S&F 3.00 mm thick figured glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

S & F aluminium alloy, anodised sliding door bolt, 300mm long, ISI marked, with hasp and staple (bolt type) and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 125 mm complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handle fabricated type anodized complete all as specified & directed.

S & F floor door stopper aluminium alloy body & tongue of size 75mm, anodised with hard drawn spring, fixed in door,over all length of cover plate of complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 200 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M & L for chequered cement concrete tiles of size 20cm x 20cm x 25mm thick with grey cement and no pigments as in floor set, jointed and pointed in neat cement slurry laid over and including 20mm thick cement screed base in CM 1:6 complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate) as in sub base, complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed stone agg regate) as in rounded or chamfered on edges in any description, complete all as specified.

Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580X440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with chinaware ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing complete all as specified and directed.

Taking out old unserviceable water closet and S & F Vitreous China wash down closet pan (pedestal pattern), white, including plastic cover white closed pattern whith flat bottom and mild steel chromium plated / PVC hinge device including connections to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed.

Taking down old unserviceable WHB and S&F vitreous China, white, wash hand basin flat back of size 550 x 400mm complete all as specified and directed

S & F in repair PVC valve less, syphonic action type flushing cistern, ISI marked, 10 litre capacity, low level, white/ivory colour, with inlet, ball valve, float, handle fixed with PVC rawl plug of suitable size complete all as specified and directed.

S & F in repair brass chromium plated shower rose of 100mm size with swivel joints, including fixing to steel pipe or union complete all as specified and directed.

Taking down old unserviceable PVC connection and S & F PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F in repair stop/angle valve 15mm bore cast copper alloy, chromium plated, fancy type ISI marked with long crutch or butterfly handle screwed down high pressure screwed both ends for iron pipe complete all as specified & directed.

S & F in repair 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union, complete, all as specified & directed.

S & F in repairs grating square/round 125mm size of PTMT with centre hole movable or side hole for fix to waste pipe (minimum weight 50 gms) complete all as specified and directed.

S & F in repair bib taps ISI marked, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore of pipe complete all as specified and directed.

S & F in repair PVC(SWR) floor trap with grating 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repair tubular towel rail, chromium plated brass 20mm dia ‘D’ type 60cm long between flanges complete all as specified and directed.

S & F in repair for Toilet fittings health faucet complete all as specified and directed. Make :- Jaquar, Prayag Cat No. 452 or make and model are equivalent as approved by GE.

Taking up or down steel tubing and connection 15mm bore keeping aside for reuse or removing to store complete all as specified and directed.

All as per srl item No 59.00 here in before but 20mm bore

Supply and fix mild steel water tubing 15 mm dia galvanised medium grade including all fittings (such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc) and fixed to walls/ceilings/ laid on floors including testing complete all as specified and as directed.

All as per srl item No 61.00 here in before but 20mm bore

S & F in repairs 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall ISI mark, complete all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall ISI mark, complete all as specified and directed.

S & F in repairs 75mm bore PVC (SWR) bend / shoe with oval access door of any radius complete all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) bend / shoe with oval access door of any radius complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

S&F in repair Jet flush including plate and coonection pipe complete all as specified and directed.

S & F in repairs stainless steel plate rack made of 1.00mm thick of over all size 914mm x 609 mm x 255 mm and weight not less than 7.00 Kg each of approved quality complete all as specified and directed.

Taking down old unserviceable kitchen sink and S&F kitchen sink with drainage board overall size not less than 915x460mm, bowl size 410x 330x160mm made of stainless steel 1.00 mm thick with plugs, washers and waste including fixing cantilever brackets and connecting union complete all as specified and directed.

Taking down of old boards and S & F 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination, fixed with screws including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works complete all as spepcified and directed.

S & F in repairs 100mm size hasp and staple, aluminium anodised, safety type including bolt to hinge plate complete all as specified and directed

S & F in repairs 75mm size hasp and staple, aluminium anodised, safety type including bolt to hinge plate complete all as specified and directed

S & F in reapirs 25mm dia stainless steel curtain rod, fancy type fixing with bracket, complete all as specified and directed.

S & F stainless steel bracket fixed suitable for 25mm dia curtain rod complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and S&F 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

Hacking out old broken glass (any thickness, size quality or description) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and S&F 3.00 mm thick figured glass, ordinary quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

M&L for 16-18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like set & jointed in neat cement slurry & pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding the exposed edges laid over & including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

S & F false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness(as per IS: 14862) of size 595x595 mm and any one of the desin (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length, and 15x32mm made from 0.30 mm thick sheet, and cross "T" of size 15x32mm made of 0.30 mm sheet, spaced between main "T" at 600mm c/c to form a grid of 600X600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixures,smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin,etc with dash fasteners,GI adjustable rods of 3mm dia with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all height and dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Taking down old unserviceable rolling shutter & S & F steel rolling shutters gear operated type with bevel gear box & crank handle, thickness of laths 1.25mm with ball bearing as specified including top cover, anchoring rod, hasp & staple and one shop coat of primer, erected in position as directed including making good disturbed surface to match the existing complete all as specified and directed.

S &F mild steel ball bearing suitable size for rolling shutter complete all as specified and directed

S &F mild steel safety lever lock with 4 levers suitable size for rolling shutter complete all as specified and directed

S & F rolled mild steel framed work as in Joist, channel, angle or Tee sections, fixed dependently without connecting plate etc (cut to ordinary lengths i.e. within 200 of the length indicated including ) including distance pieces, cleats etc including drilling for fixing of steel sheeting or other covering confirming to Fe-290 (Gde E-165) quality-A complete all as specified and directed

M&L for providing precast cement concrete louvers and jallies, 35mm thick (measured solid) 1:2:4 type B-0 (using 12.5mm thick graded stone aggrigate) set in CM 1:4 including all mouldings complete all as specified and directed.

S & F in repair for Toilet fittings corner glass shelf with bracket complete all as specified and directed. Make :- Jaquar Cat No. CAN-CHR-1173 or make and model are equivalent as approved by GE.

S&F in repairs aluminium door shutters with frame of aluminium section weighing not less than 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mmx 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor spring made up of 1.25 mm thick aluminium alloy sheet, foundation box for each shutter etc and including fitted with 5 mm thick tinned glass in glazed shutter with brass mortice lock of 100mm , 2 levers, vertical type, complete, all as specified in clause 10.37 of SSR Part I & directed by Engr-in-Charge.

M & L for vitrified ceramic tiles light shade 10mm thick (square / rectangular) polished area of each tiles exc. 0.18 sqm but n.exc 0.36sqm in floor, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tile laid over and including screed bed 15mm thick in CM (1:6) complete all as specified and directed.

All as per Sl item no 88.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set & jointed in neat slurry and pointed in white cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in CM 1:4 complete all as specified and directed.

M&L for 100mm thick PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in floor surface finished fair and even complete all as specified and directed.

M/S SHIVA TRADERS

kirtiman traders

Shree Sai Ram Enterprises

M/s Jai Jinendra Constructions

M/s S. K. Construction Co.

SHREE BALAJI TRADING CORPORATION

SHRI RADHAYSHYAM JHA

V K LAKWAL CONSTRUCTION