Special Repair of Sub Divisional Hospital at Mohindergarh in Mohindergarh District (i/c E.I. Work) (Re-invited)

Amount

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantled (HSR 8.18) (a) doors

(b) windows

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (HSR 17.93 a) (i) 25 mm thick

(iii) 35 mm thick

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge.(HSR 30.119) 1000 Ltr. Capacity

Providing and fixing in position best Indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully described in item No. 30.41 above (HSR 30.42) White, (i) Size 510mm x 400mm with one no. tap

EXTRA OVER item nos. 30.1 TO 30.4 AND 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. eistern complete (as approved by the Engineer-in-charge). (HSR 30.8) (i) White

Scraping, (a) white wash and colour wash (HSR 8.32 a)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla). (HSR 16.81)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on old work, one coat to give an even shade. (HSR 16.62)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, onforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: - (a) door and window frame of size 89 mm X 50 mm with 40 mm wide single rebate (HSR 18.34 a)

Dismantling Concrete (d) cement concrete plain 1:2: 4 mi (HSR 8.6 d)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

E.I. Works Main Switches - 31.12(a) Supply and erection of metal clad switches / B.D.Bs with rag bolts on wall or on existing angle iron board / pedestal including bonding to earth and necessary connections. Triple pole switch with neutral link 200 amp. 415 Volts. (xvii) Cat-A

Moulded case Circuit breakers. (HSR 31.12) (c) Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

(ii) 100 amp.to 220 amp.415 V,10 KA 3-phase.

Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suiteble size of rag bolts with cement concrete ,duly painted with three coats of approved paint including one coat of red oxide. (HSR 31.13) (ii) Size 40 mm x 40 mm x 6 mm.

M.S.Sheet . (HSR 31.14) (i) Supply and erection of 3 mm thick mild steel sheet duly welded on existing M.S. angle iron frame for fixing the main switches etc. as required, duly painted with three coats of approved paint including one coat of red oxide.

Distrubution board with plug and socket. (HSR 31.15) Supply and erection of sheet steel enclosure 2 pole / 3 pole with earth plug and socket suitable for incorporating single pole / triple pole MCB on wall / on existing pedestal complete with necessary connections etc. (ii) S.P.N. enclosure for single pole MCB 20 amp.

Miniature Circuit Breaker and Isolator. (HSR 31.17) Supply and erection of miniature circuit breaker/ isolator 240/415 V in the existing distribution board including making necessary connection. (a) Miniature circuit breakers of 9 KA breaking capacity. (ii) SP MCB 6 amp. to 32 amp.

(iii) TPN MCB 40 amp. to 63 amp.

Supply and erection of Fittings and Accessories. (HSR 31.18) (xi) Bakelite angle / straight button holder large size.

Pipe Laying. (HSR 31.21) Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. (xv) Heavy guage welded conduit pipe 20 mm dia 1.60 mm thickness on surface.

(xvi) Heavy guage welded conduit pipe 25 mm dia 1.60 mm thickness on surface.

Earthing (HSR 31.22) (i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required.

(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

(iii) Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

(v) Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

(xi) Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required .

(xv) Pdg. and fixing 25 mm x 5 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material.

(xvi) Pdg. and fixing 4.00 mm dia G.I.wire on surface or in recess for loop earthing as required .

Under Ground Cables. (HSR 31.25) Supply and erection of under ground cable 1 metre below ground level covered with sand and bricks including necessary connections,digging and refiling of trenches. (xxvi) 35 Sq. mm 3.5 Core Ard Cable .

(xxvii) 70 Sq. mm 3.5 Core Ard Cable .

Supply and erection of under ground cable, loose in existing pipe or trenches complete with necessary connections. (HSR 31.26) (xxvi) 35 Sq. mm 3.5 Core Ard Cable

(xxviii) 70 Sq. mm 3.5 Core Ard Cable .

Supply and erection of suitable compression type brass cable glands for underground Cable.(HSR 31.28) (iii) 25 Sqmm to 50 Sqmm Cable 2 to 4 Core.

(iv) 70 Sqmm to 95 Sqmm Cable 3 to 3.5 Core .

PVC Insulated wiring in Surface Conduit . (HSR 31.37) Wiring in 1.5 sq.mm PVC Insulated copper conductor cable in 1.6 mm thick conduit pipe. (i) Fan Point - b) Medium Point .

c) Long Point .

(ii) Light point - a) Short Point

b) Medium Point .

c) Long Point .

(viii) 3 pin 15 amp. plug point including earthing the 3rd. pin etc. with 4 sq mm PVC insulated copper conductor cable. c) Long point.

Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe. (HSR 31.40) i) Cable size 1.5 sq.mm(3/ 0.81 mm)

(iii) Cable size 4.0 sq.mm(7/ 0.85 mm)

iv) Cable size 6.0 sq.mm(7/ 1.05 mm)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-charge of work. (HSR 31.41) (v) 4 way TP&N (Horizontal) (8 + 12)

Supply & erection of Socket size rotary step type Electronic regulator for A.C. ceiling fan Anchor make Delux model No. 50440 ISI / SSK make PC 561 operated on 120/280 V A.C. Supply complete including cutting of existing Bakelite sheet and making necessary connection etc. up to the entire satisfaction of the Engineer-in-Charge of the Work. (HSR 31.55)

Supply, installation, testing and commissioning of Load bank with digital metermodule cost of digital Amp./Volt meter with sector switch wiring etc. suitable for operation of 240/415 volts A.C supply with both side cable allay inter connection and fixing the same in existing MS pedestal complete with all labour and material required for the same up to the entire satisfaction of Engineer-in-charge of work. (HSR 31.75) iii) Load Bank 4 way 400 Amp.

Supply and erection of Exhaust Fan 15'' complete in all respect upto the entire satisfaction of the Engineer -in-charge of the work Make Bajaj / Crompton /Orient / Havells. (MR)

Supply and erection of LED 18 W batten fitting complete in all respect Make Bajaj / Crompton /Jaquar / Havells / Surya. (MR)