PROVN OF ACCN FOR DENTAL SEC NEAR CENTRAL MI ROOM (BLDG NO P-279) AND PROVN OF SHED FOR STORAGE OF LIQUID PETROLEUM GAS OF SUPPLY DEPOT ASC AT GWALIOR

Amount

Surface dressing n.exc 30cm deep average 15cm deep in Soft Loose soil complete all as specified and directed.

Removing excavated material exc 250m but n.exc 500m and depositing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n. exc 3.00 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and directed.

M&L Plain cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams , plinth beams , base for coloumns and mass concrete etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in coloumns , pillars , piers , posts and struts etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in beams , cantilevers bressummers, lintel over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in slab supported on walls ,beams, coumnns in floor , roof , landing complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 ( using 20 mm graded stone aggregate ) as in Chajjas complete all as specified and directed.

M&L for use and waste formwork to sides of concrete foundation , footing, base of coulmn , raft, raft beam sides and soffits of foundation and plinth beam for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork to soffits of suspended slabs such as roof slabs , floor slabs , landings and similar works , not exceeding 200 mm thick ( horizontal or sloping ) including slab edges for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork to fins, louvers, fascia for rough finished surfaces of concrete complete all as specified and directed.

M&L use and waste formwork for to sides of pillar ,post ,struts ,pier column rough finished surfaces of concrete rough finished surfaces of concrete complete all as specified and directed.

M&L for use and waste Formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed.

M&L for Use and waste Formwork to chajjas including edges for rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars ,6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia , as in stirrups , spacers , and binders , cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L forTreating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for Treating the soilbackfill in contact with foundation at the rate of 7.5 litre of emulsion per square meter of vertical surface (area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for Moorum red bajri filling in floor or paving laid in layers n. exc. 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of 8 to 10 mm thick (Square / Rectangular ) polished area of each tiles not exceeding 0.36 Sqm as in flooring over and including 15 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of width as directed and 8 to 9 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for non skid ceramic, joint free Coloured tiles, 300mmx300mmx 6 mm to 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar( 1:6) complete all as specified and directed.

M&L for digital glazed ceramic tiles,joint free coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

M&L for machine cut Kota stone slab 18 mm to 22 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing , over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:3 ) complete all as specified and directed.

M&L for machine cut kota stone slab 10 mm -15 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L Granite slab 18 mm to 20 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed CM (1:3) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing all as specified and directed.

M&L white marble stone strip as in border etc in kota stone flooring machine cut bedded over and including 20 mm thick screed bed CM (1:3) jointed and ointed with grey cement slurry including cutting and polishing to mirror finish complete all as specified and directed.

M&L for rubble random rubble uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work (old size) with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and directed.

M&L for Brick work modular size with Fly ash bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and directed.

M& L for B Brick work modular size with Fly ash bricks straighor curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement including complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M & L for two coat of oil bound emulsion paint over a coat of Birla wall care putty on plastered surfaces on wall incl. preparation of surfaces complete all as specified and directed. .

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coat of cement base paint over a coat of primer complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters of aluminium section weighing 0.35 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc. complete all as specified and directed. Note : Panel filling ie. glass, fibre sheet, board etc. shall be measure and paid for separately.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track(sliding oenable)) without sash, aluminium section weighing 0.25 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed. Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S & F for door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast body (ISI Marked), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed.

S & F of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed.

S&F 12mm thick toughned designer glass fixed on steel pivot all as approved sample with engravings/ designs/ symbols to the pattern and style as approved and directed.

S&F 'D' type stanless steel handle decorative type 300mm long bright finished all as per design/ pattern approved by Engineer-in-Charge.

S&F galvanised wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

S&F pressed steel frame 125mmx60mm for doors with one or more rebates including necessary supply and fixing lungs and butt hinges 100mm, lock strike plate,etc complete all as specified and directed.

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

S&F aluminium alloy, anodized sliding door bolt of 250mm length with hasp and staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for aluminium anodised barrel tower bolt of 150mm of extruded section complete all as specified and directed.

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and directed.

S &F for factory made solid panel PVC door shutter 30mm thick ( style) consisting to frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed.

M & L for 30mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290,E-165 , complete all as specified and directed.

S&F for floor door stopper of brass body and tongue, overall length of cover plate 150 mm , anodized, with hard drawn steel spring , fixed to shutters complete all as specified and directed.

S&F 25mm dia stainless steel curtain rod not less than 0.80mm thick including fixing of sufficient brackets ( minium 2 nos at every 1.50m length) and knobs complete all as specified and directed.

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.

S&F for of vitreous china wash basin, white, oval type/ SURGERY SPECIAL (size as approved by Engineer In charge) Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid separetly.

S&F for viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed.

S&F plastic water closet seat covered white coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devise complete all as specified and directed.

M&L for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed and making good to floor, complete all as specified and directed.

S&F for vitreous china, Half stall type ,white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F for PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

M&L painting to steel surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of red oxide including prepration of newly or previously untreated surface complete all as specified.

M&L painting to wooden surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of pink primer including prepration of newly or previously untreated surface complete all as specified.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and fair mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) land on primed surface by torch application complete all as specified and directed.

M&L one coat of aluminium bituminous paint over polymetric membrane complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in ant type of soil complete all as specified and directed. Note : Soil under filling will be approved by GE. Black cotton soil not be used in returning filling rate of filling of approved soil include in this item, no extra payment given for filling of soil.

S & F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triplr layer in construction white in colour hoisted and fixed in position complete all as specified and directed.

S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S & F 15 mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc complete all as specified and directed.

S & F 20 mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc complete all as specified and directed.

S&F for gun metal globe valve with iron wheel head screwed both ends for iron pipe of 20mm bore, complete all as specified and directed.

S&F for 15mm ,bib tap ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket and guard and railing 60cm long completed all as specified and directed

S&F for Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F 15mm angle cock ISI Mark chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified and directed.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed

S&F PVC (SWR) pipes, 75 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) pipes, 110 mm bore, single sockets, in any length with rubber ring joints laid in floors or wall complete all as specified and directed.

S&F PVC (SWR) Single junction (single T) equal or unequal, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) Single junction (single T) equal or unequal, , 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends with access door, 110 mm bore, any radius with access door complete all as specified and directed.

M&L for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

M&L cast iron nahani trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) etc complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F for peg set of six M.S. Cast Iron . fixed to wall with PVC plugs and screw, complete all as specified and directed.

S&F for 18 mm thick PVC Celuka ply of one side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised complete all as specified and directed.

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified and directed.

S&F for in repairs Heatth Faucet (ABS Body) mild steel chromium plated 15 mm dia with 1.25 meter PVC flexible body pipe of CP including fixing bracket, complete all as specified and directed.

M&L for PCC 1:3:6 type C0 (12.5mm agrregate) for filling in pressed steel frames and like complete all as specified and directed

Preparattion of surfaces for writing Building numbers and applying two coat of synthetic enamel paint back ground 30 cm dia and writing letters (Block, Roman, italic or indian) of n exc 10 cm height, width of letter shall not be less than 15mm, with approved tint of synthetic enamel thick paint etc complete all as specified and directed.

Preparattion of surfaces for stops, commas, lines, brackets and making outer boarder with approved tint of synthetic enamel thick paint and applying two coat of synthetic enamel paint etc complete all as specified and directed.

M&L for Rough dressed sand stone slab edging 40mm to 50mm thick laid dry but bedded jointed and pointed in cement mortar 1:3 in vertical surfaces including excavation and making good surfaces complete all as specified and directed.

Rolling and consolidating formation surfaces in cutting with power roller of capacity exc 8 tonne and n.exc 12 tonne complete all as specified and directed.

M&L Soiling (or subbase ),150 mm thick (spread thickness ) with crushed or broken ballast /trap stone of grading 63 to 90 mm boulders or quarried stone ,interstices filled ,surface formed and rollled and consoildated to requried gradient and camber with 8 to 12 tonne power roller complete all as specified and directed.

M&L for 150 mm thick (compacted thickness) WBM in two layers of each one layer 75mm thick (compacted thickness) with coarse stone aggregate (sandstone, limestone) of grading 2 (63 to 40mm size spread & rolled with 8 to 12 tonne power roller, rolled and consolidated to required gradient and camber complete all as specified and directed.

Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc applying evenly a priming /tack coat with paving bituminous primer VG-10 grade at 10kg per 10 Sqm complete all as specified and directed.

Material and Labour for bituminous premix semi dense asphaltic concrete , 40mm consolidated / compacted thickness using Hot Mix plant and machanical paver with 5.5% (paving bitumen VG-30 grade)(Min) binder content by weight of total mix, rolled and compacted using 8 to 10 tonne power road roller to required camber and gradient complete all as specified and directed.

M&L for retro reflective thermo plastic road marking paint 1.25 mm thick, uniform finish yellow/ white in colour, applied by machine, not exceeding 15cm in width, all as specified and confirming to BS -3262-1989 including cleaning of surface complete all as specified and directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand), including making joints with or without grooves ( thickness of joints expecet at sharp curve shall not more than 5 mm ), including making drainage opening wherever required complete all as specified and directed.

M&L for preparation of undecorated concrete surface of road side kerbs / appex stones and similar items of any description and in any position exceeding 10 cm width or girth and apply two coat of synthetic enamel paint to the strip pattern and of different tint(s) complete all as specified and directed.

M&L fir cement concrete ( 1:2:4) type B-1 (20mm graded agrregate) in lintels upto 1.5m clear span, cills, stes, seimic and other similar bands, plinth course, string course, lacing cours, arapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water througs and the like including wheathering slightly rounded or chamfered angle and throating complete all as specified and directed.

Excavating in posts holes (or similar holes) in soft/loose soil each n.exc 0.50 cu.m getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm watering, and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed.

M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 complete all as specified and directed

Supply only, chain link fencing of MS galvanized fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separetly.

S&F mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooking ends stiffeners confirming toFe 290 (Gde E-165). complete all as specified and directed ( welding of round bar should be include in item quoted rate no extra payment will be given.)

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt exc 5cm but n.exc 10cm long and dia of neck 11 to 15mm complete all as specified and directed.

S&F galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including, securing and tying at crossings with and provisions of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured).

M & L Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed

S&F framed work (ornamental) as in steel gate of angle or other section with gusset plate ,rails braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hook and hinges and also fastening and fixing Fe-290 ( Gde-E-165) complete all as specified and directed.

M&L Granite slab 18 mm to 20 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 10 mm thick screed bed CM (1:3) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing all as specified and directed..

Removing excavated soil to a distancen. exc 250m but n exc 500m depositing where directed at a level n.exc 1.5m above starting point complete all as specified and directed.

M&L,precast cement concrete 1:2:4 type B1 using 20mm graded BT stone agregate including necessary form work as in manholes cover slab etc, set in cement mortar 1:4 complete all as specified and as directed. (Note :- Re-inforcement shall be measured and paid for separately under respective items of Sch 'A' here in after)

Removal of excavated material (soil) to a distance n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

M&L, PCC 1:4:8 type D2 using 40mm graded BTstone aggregate as in concrete bed to drain pipes of 150 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; including necessary form work complete all as specified and as directed.

S&F for reinforced concrete pipes 150mm bore class NP-2 laid and jointed with collar in CM 1:1 complete all as specified and directed.

M&L, PCC 1:2:4 type B1 using 20mm graded BT stone aggregate as in mass concrete, bed block, coping / surface channel and the like including weathering, slightly rounded or chamfered angles and throating, including form work complete all as specified and as directed.

M&L,cutting into existing manholes for connecting new drains of 150 mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed.

M&L, PCC 1:2:4 type B1 using 20mm graded BT stone aggregate as in bed block, coping and the like including weathering, slightly rounded or chamfered angles and throating, including form work complete all as specified and as directed.

M&L, 15mm thick rendering on any faces of stone, concrete or brick work in CM 1:6 mixed with water proofing compound as per manufacturer instruction , surface finished even and fair complete all as specified and as directed.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 3 pin socket outlet 5 Amps controlled with one switch on the same board.

One 3 pin socket outlet 5 Amp controlled by one switch on independent board.

One bell point controlled by one bell push

All as per Ser item No. 144 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete all as specified and directed.

S&F Switch socket combination 2 in 1, 6 pin, 5/15 Amp flush type universal complete all as specified and directed.

S&F bell push flush type, 5 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F Ceiling rose 3 terminal/pvc/polycarbonate, isolated body complete all as specified and directed.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete all as specified and directed.

S&F LED Lamp 09/10 watt complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply & fix BEE 5 Star rating(BLDC) energy efficient ceiling fans 1400 mm sweep with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed.

Supply and fix exhaust fan double bearing metal body copper wound 300 mm sweep with, blades, and frame and louvers including making hole & reqd length of 3 core 1.0 Sq mm PVC multistranded copper conductor,and testing complete all as specified and directed.

Supply and fix PVC Fresh Air Fan 300 mm sweep with all fixing accessories requrired including making hole & reqd lenth of 3 core 1 sqmm PVC multistranded copper conductor and testing complete all as specified and directed.

S&F sheet metal Enclosure with socket Plug top and earth plug, single pole and neutral with single pole MCB 20 Amps 240 volts in repairs complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

All as per Ser item No. 161 above but submain with 4 sqmm FRLSH confirming to IS 694:2010, multistrand copper (ISI marked with valid CML No), cable 1100 Volt grade, 2.5 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed.

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp,4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 8 way rated bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 40 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 70 Sqmm 3.5 Core complete all as specified and directed.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and directed.

Bricks,old size sub class B laid in trenches with width wise along the aligment of the cable as protection complete all as specified and directed.

S&F tube 'Light' grade galvanised pipe of 50mm dia with all fitting for cable protection, laid in trenches, fixed to wall and floor by MS shaddle & fixed with pole, 02 position by MS clamp made of 40 x 5mm MS flat, complete all as specified and directed.

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole & Including MCCB 125 amps 4 pole 25 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

S&F tube Medium grade galvanised with all fitting in laid in treches,of 40 mm dia complete all as specified and directed.

S&F tube Medium grade galvanised with all fitting in laid in treches,of 20 mm dia complete all as specified and directed.

S&F Gun-metal,gate valves,with iron wheel head,screwed both ends for iron pipe of 40mm dia complete all as specified and directed.

S&F Gun-metal,gate valves,with iron wheel head,screwed both ends for iron pipe of 20 mm dia complete all as specified and directed.

M&L for construction of valve chmabers os size 1.5 x 1.5x1.2 internal dimentions with 150mm thick PCC foundation 1:4:8 type D2 using 40mm graded trap stone aggregate, 230 mm thick brick masonary wall with sub class 'B' bricks builts in cement mortar 1:4 10mm thick plastering to brick masonary in cement mortar internally nand externally upto 15cm below ground level, 50 mm thick coping with PCC 1:2: 4 type B1 using 20 mm graded crushed trap stone aggreate value chamber having cover frame size 1.5x1.5x1.2 made of mild steel angles of sixe 50mm x 50mm x 6mm and cover made of 2.5mm thick mild steel sheet framed by 40x40x5mm MS angle having 02 nos cross 'X' support fixed with coller frame by mild steel hinges-02 Nos, locking arrangements with provision of locks and painting the steel surfaces with two coats of alluminum enameled paint cover a coat os zinc chromate primer inculding necessary earth work, excavation, all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Cutting of existing cast iron pipes in position for insertion of new tees for branch connection of 40mm dia from 100 mm bore of pipe existing CI pipe complete all as specified and directed.

Supply and install, Hi wall split unit indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of 2 TR capacity five star rated completed all as specified and directed.

Supply & installation,commissioning of voltage stabilizer for automatic operation single phase naturally air cooled indoor type & designed for input variation between 170 volts to 250 volts 50 Hz with output voltagned stablized at 230 volts with accuracy of +2.5% and of capacoty 2 KVA complete all as specified and directed.

Supply & fixing water heater storage type stainless steel inner container, 25 Ltrs capacity, electric suitable for single phase, 50 Hz, AC Supply, 5 star rating, including all necessary fittings and fixture with minimum 1M of three core 2.5 sqmm twisted copper conductor cable PVC sheated, three pin plug top complete with necessary fittings and fixtures all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in Soft Loose soil complete all as specified and directed.

Excavating over areas, exceeding 1.5 m but n. exc 3.00 m in depth; deep and getting out in soft loose soil complete all as specified and directed.

M & L for PCC (1:2:4) Type Bo using 20 mm graded stone aggregate as levelling course/mass concrete complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 3 coat of White wash complete all as specified and directed.

S & F factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays , complete with glazing bars, complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality in square n exc 0.5 sqm each pane in new glazed shutter, complete all as specified and directed.

S&F MS Black plain sheet in wall clading and similar work cut to size and fixed to steel frames work with 40 mm lap joint including welding ,bending or turning of 1.60 mm thick complete all as specified and directed.

S&F for framed workas in doors or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering, Doorsetc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing complete conforming to Fe 290 GDE -E -165, complete all as specified and directed.

M&L for Sand Filling Under Floor or in foundations including watering and consolidation comleted all as specified and directed.

Preparattion of surfaces for stops, commas, lines, brackets and making outer boarder with approved tint of synthetic enamel thick paint and applying two coat of synthetic enamel paint etc complete all as specified and directed.

M&L for preparation of newly plastered surface of wall & applying two coat of cement base paint over a coat of alkali primer complete all as specified and directed.

M/s Ratan Lal Jain and Co.