Recanning of chairs all types , repairing of charpoy GI/IP and repair to sofa set, chair CB steel, chair CBA special and various type of chair cushioned and certain repair to wooden / steel furniture under GE (North) Bikaner at Mil Stn Bikaner

Amount

RECANNING OF CHAIRS, FD-279, FD-229, FD-280, FD-282 (a) Removing of old unserviceable plastic cane from all sorts of chairs i.e chair dining, chair writing, chair easy , stool dressing CB etc (except chair verandah) including recaning with new cane of white colour of size 3 mm wide and 0.60 mm thick (flat) alround for border of seat and back and 2 mm wide and 0.40 mm thick half round for remaining portion, complete all as specified and as directed by Engineer - in - Charge

RECANNING CHAIR VARANDAH FD-359 & FD-256 (a) Removing of old unserviceable cane plastic from chair verandah, painting with one coat of synthetic enamel paint (White) after preparation of old painted surfaces, including recanning with new cane of white colour of size 4 mm wide and 0.60 mm thick for seat and back, closely woven as per mat pattern all as shown on drawing and also including providing new rubber shoes at the bottom of legs after removing of old shoes complete all as specified and as directed by Engineer-in-Change.

(b) Providing one additional stiffener on MS round bar 6 mm dia on the back side joining both legs by gas welding including a coat of primer

(c) Painting steel and iron surfaces of the chair complete by spray painting synthetic enamel paint of white shade including preparation of steel and iron surfaces (Priming with red oxide primer shall be done wherever welding is carried out for the broken joints and also replacemnt of old unservicable required parts and filler coat applies).

(d) Supply and fixing 04 Nos hard rubber shoes to each chair verandah as per drawings.

Replacement of U/S ply top/ Nylon Newer of Charpoy GI Pipe with new Plywood top, FD-220 (i) Removing of unserviceable plywood/ Nylon Newar from Charpoy GI Pipe, tightening of loose check nuts, elbows, long rails. Short rails, legs (i.e., complete charpoy) and supply and fixing the 12 mm thick 7 ply, commercial type BWR, exterior grade (water proof), ISI-303 marked of size 1980 x 900 mm fixed on top of GI Charpoy as shown on drawing with mild steel galvanized iron nuts & bolts of size 70mmx6mm with GI washer ( heavy weight) and three stiffner made out of MS flat iron 35 x 5 mm parallel to short rail duly painted black will be welded between the long rail (All as approved by GE and directed by Engr -in- charge.

(ii) Removing of unserviceable long rail of charpoy GI Pipe and supply and fixing new long rail duly threading both side /welding properly made out of GI tubing 32 mm bore medium grade duly painted portion all as per sample available. Threading/welding of new rail as per best trade practice and as approved by GE. Make of GI Pipe :- Jindal/Prakash surya/ Tata/BST. Note :- Unit of measurement of this item is 'Each' which shall comprise of removing, supply and fixing of one long rail and all as specified.

(iii) Removing of unserviceable short rail of charpoy of GI Pipe and fixing of short rail made out of broken long rail obtained from Srl item No 3 (ii) above threading/welding of both ends of short rail as per best trade practice duly painted with aluminum paint of welding portion and directed by Engr-in-charge. Note :- Unit of measurement of this item is 'Each' which shall comprise of removing and fixing of one short rail and all as specified.

(iv) Removing of old unserviceable 3 way elbow 32mm bore and supplied and fixed in position new elbow ISI marked all as per sample available in BSO's Yard complete all as approved by GE and as directed by Engr-in-charge

(v) Removing of old unserviceable check nuts and supplied and fixed in position new check nuts to Charpoy GI Pipe all as per sample available in BSO's Yard complete all as approved by GE and as directed by Engr-in-charge

(vi) Removing of unserviceable leg of charpoy of GI Pipe and fixing of leg made out of broken short rail obtained from Srl item No 3 (iii) above welding of both ends of leg as per best trade practice duly painted with aluminum paint of welding portion and directed by Engr-in-charge. Note :- Unit of measurement of this item is 'Each' which shall comprise of removing and fixing of one leg and all as specified above/directed by Engr-in-charge.

(vii) M & L for electric welding of long rails, short rails, legs of 32 mm bore GI tubing by continuous welding around the broken joints duly painted with aluminum paint of welding portion all as directed by Engr-in-charge. Note :- (i) Unit of measurement of this item is 'Each' which shall comprise of welding of each broken joint all as specified above/directed by Engr-in-charge. (ii) Welding rods shall be ISI marked.

Replacement of U/S ply top of Charpoy IP with new Hard top (Drg FD/MAP-II/01) (i) Removing of unserviceable plywood from Charpoy IP, Supply and fixing the 12 mm thick plywood sheet on top, suitable for Charpoy IP as shown on drg. of size 1980 x 900 mm (BWR) as per IS-303 with mild steel galvanized iron nuts & bolts of size 70mmx6mm with GI washer ( heavy weight) and including electric welding of loose long rail, short rail, legs, centre stiffener 25 x 25 mm square MS tube and cleat tube size of 25 x 60 mm x6 mm of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) after preparation of old painted surface with providing four nos new hard rubber shoes to each charpoy IP at the bottom of legs after removing of old shoes complete all as specified and directed by GE/Engineer-in-Charge. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and washers, PVC shoes and painting of the charpoy IP to be included in the quoted rate.

Replacement of U/S ply top of Bed hard with steel frame FD/E6/MAP-08(R) (i) Removing of unserviceable ply wood from Bed hard with steel frame fixing the 12mm thick ply wood sheet on top suitable for Bed hard with steel frame as shown on drg of size 1980 x 900mm (BWR) as per IS-303 with mild steel galvanized iron nuts & bolts with GI washer (Heavy weight) and including electric welding of loose long rail short rail, legs centre stiffender, Head rest, Foot rest and cleat of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) after preparation of old painted surfaces with provding 04 Nos new hard rubber shoes to each Bed hard with steel frame at the bottom of legs after removing of old shoes complete all as specified and as directed by Engineer-in-charge. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and washers, PVC shoes and painting of the Bed hard steel to be included in the quoted rate.

(ii) S & F of new head rest made of pre-laminated particle board 18mm thick both side teak face of exterior grade with 04mm thick teak wood beading shall be provided all-round including screws and welding of cleat all as specified in drawing directed by Eng-in-Charge.

(iii) S&F of new Foot rest made of pre-laminated particle board 18mm thick both side teak face of exterior grade with 04mm thick teak wood beading shall be provided all-round including screws and welding of cleat all as specified in drawing directed by Eng-in-Charge.

Chair CB Steel with arms FD-75(M) (a) Opening up and removal of seat, back, shoes and arms of chair CBA steel and preparation of old painted steel surfaces frame with one coat of synthetic enamel paint olive green colour and old painted wooden surfaces with one coat of synthetic enamel black paint, and refixing of seat / back / arms if in serviceable condition. (The seat, back and arm if replaced shall be paid separately under respective items of Schedule ‘A’ here in after as supply only. The cost of steel bolts 3"long, 1/8"dia with nut & washers etc shall be deemed to be included in the quoted rates of this item).

(b) Supply only wooden seats of IInd class hard wood duly caned (Godrej pattern) and duly painted for chair CBA steel.

(c) Supply only wooden back of IInd class hard wood duly caned (Godrej pattern) and duly painted for chair CBA steel.

( d) Supply of arm of IInd class hard wood duly painted for chair CBA steel.

(e) Supply and fixing of MS flat iron 25 x 3 mm duly welded to seat frame of chair CBA steel with both side front and back and duly synthetic enamel painted w/are coat of Red oxide and over it are coat of olive green paint.

Chair CB Steel with out arms FD-75(M) (a) Opening up and removal of seat, back and shoes of chair CB steel and preparation of old painted steel surfaces frame with one coat of synthetic enamel paint olive green colour and old painted wooden surfaces with one coat of synthetic enamel black paint, and refixing of seat/back if in serviceable condition. (The seat and back shoes if replaced shall be paid separately under respective items of Schedule ‘A’ here in after as supply only. The cost of steel bolts 3” long, 1/8” dia with nut and washers etc shall be deemed to be included in the quoted rates of this item.

(b) Supply only wooden seats of IInd class hard wood duly caned (Godrej pattern) and polished for chair CB steel.

(c) Supply only wooden back of IInd class hard wood duly caned (Godrej pattern) and polished for chair CB steel.

(d) Supply only PVC shoe black for chair steel CBA and CB as shown on drawing.

(e) Supply and fixing of MS flat iron 25 x 3 mm duly welded to seat frame of chair CB steel with both side front and back

Sofa Set 4/5 Seats FD-373 (a) Replacement of seat and back cushion 100 mm thick made of cool foam (Make : Sleepwell/ kurlon ) of 32 density duly covered with well finished best quality tapestry cloth not less than Rs 250/- meter shade and quality shall be approved by Engr-in- charge/GE.

(b) Replacement of long, front and back rail made of well seasonedsheesham wood duly plained / smoothened after taking out the old unserviceable one of 3 seater chair.

(c) Replacement of long, front and back rail, rest all as per item No. 3(b) here in before but single seater.

(d) Replacement of short stiffeners well seasoned 1st quality sheesham wood all as specified in drawings after taking out the old existing unserviceable one of 3 seater /single seater

(e) Replacement of front legs of well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater.

(f) Replacement of back legs of well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater.

(g) Replacement of Arms well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable of Sofa Chair 4/5 seater.

(h) Polishing all new and old surface with two caots of french polish after preparation of old surface complete all as specified.

Repairs to Chair CB Spl with hand rest FD-75(M) (a) Removing old unserviceable seat of chair CB special with hand rest and in lieu providing new seat of chair CB special with hand rest as per specification mentioned in drg (including fixing materials). FD-75 (M) SH 1/1

(b) Removing old unserviceable back seat of Chair CB spl with hand rest and in lieu providing new back seat of chair CB special with hand rest as per specification mentioned in drg (including fixing materials).

(c) Removing old unserviceable hand rest of chair CB special and in lieu providing new hand rest as per drg.

(d) Painting to steel & iron surface of chair one coat by spray gun with synthetic enamel paint of olive green shade after preparation of old surface complete all as specified.

Chair dinning Cushioned /long back FD/E6/MAP/10 (R) (a) Replacement of seat cushioned 75 mm thick made of cool foam (Make : Sleepwell/ kurlon) of 32 density including ply wood 12mm thick suitable for seat duly covered with well finished best quality tapestry cloth not less than Rs 250/- meter shade and quality shall be approved by Engr-in- charge/GE.

(b) Replacement of front legs made of well seasoned sheesham wood duly plaine/smoothened after taking out the old unserviceable front legs

(c) Replacement of rear legs rest all as per item No. 10 (b) here in before

(d) Replacement of front and back rail well seasoned sheesham wood all as specified in drawings after taking out the old existing unserviceable rails

(e) Replacement of side rail well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable side rails.

(f) Replacement of back rail stiffner , side and middle stiffner well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable stiffners.

(g) S&F second class hard wood corner / bracket (L shape) of size 50mm x 50mm x 20mm thick fitted with screw between side rail to legs.

(h) Polishing all new and old surface with two caots of french polish after preparation of old surface complete all as specified.

Chair easy Cushioned FD-358 (a) Replacement of seat cushioned 75 mm thick made of cool foam (Make : Sleepwell/ kurlon ) of 32 density duly covered with well finished best quality tapestry cloth not less than Rs 250/- Per meter shade and quality shall be approved by Engr-in- charge/GE.

(b) Replacement of back cushioned 75 mm thick made of cool foam (Make : Sleepwell/ kurlon ) of 32 density duly covered with well finished best quality tapestry cloth not less than Rs 250/- per meter shade and quality shall be approved by Engr-in- charge/GE.

(c) Replacement of front legs made of well seasoned sheesham wood duly plained/smoothened after taking out the old unserviceablefront legs.

(d) Replacement of rear legs rest all as per item No. 11 (b) here in before

(e) Replacement of front and back rail well seasoned sheesham wood all as specified in drawings after taking out the old existing unserviceable rails.

(f) Replacement of side rail well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable side rails.

(g) Polishing all new and old surface with two caots of french polish after preparation of old surface complete all as specified.

Chair revolving /chair computer FD-E6/MAP/01 & TP (a) M & L Tapestry/Fabric cloth over sythetic foam 25mm thick (as approved) for seat of chair computer/chair revolving including taking out old worn out Tapestry/Fabric Cloth & Foam from chairs and seat 12mm hot pressed plywood complete all as specified and as directed by Engineer-in-Charge.

(b) M & L Tapestry/Fabric cloth over sythetic foam 25mm thick (as approved) for back of chair computer/chair revolving including taking out old worn out Tapestry/Fabric Cloth & Foam from chairs and back 12mm hot pressed plywood complete all as specified and as directed by Engineer-in-Charge.

(c) M& L twin Castor Wheel (as approved) of chair computer/chair revolving including taking out unserviceable or broken Caster Wheel from Chairs, complete all as specified and as directed.

(d) M & L bottom base (as approved) of chair computer/chair revolving including taking out unserviceable Bottom base from Chairs, complete all as specified and as directed.

(e) M&L as lifting hydrolic system of chair computer/chair- revolving including taking out unserviceable Gas Lifting Hydrolic System from Chairs, complete all as specified and as directed.

(f) M&L handle of chair computer/chair visitor/chair revolving including taking out unserviceable handle from Chairs, complete all as specified and as directed.

Chair writing/ chair visitor FD/MAP/E6/12 (a) S & F Tapestry/Fabric cloth over sythetic foam 25mm thick (as approved) for seat of chair writing/ chair visitor including taking out old worn out Tapestry / Fabric Cloth & Foam from chairs and seat 12mm hot pressed plywood complete all as specified and as directed by Engineer-in-Charge.

(b) S & F Tapestry/Fabric cloth over sythetic foam 25 mm thick (as approved) for back of chair writing/ chair visitor including taking out old worn out Tapestry/Fabric Cloth & Foam from chairs and seat 12mm hot pressed plywood complete all as specified and as directed by Engineer-in-Charge.

(c) S & F handle of chair writing/ chair visitor including taking out unserviceable handle from Chair including welding of broken joints and painting of steel surface of the chair with one coat of synthetic enamel of black shade complete all as specified and as directed by Engineer-in-Charge. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and screws and painting of the chair to be included in the quoted rate.

Chair school with handboard (MAP) FD/MAP/E6/05 (a) Removing old unserviceable one piece pvc seat and back of chair school with handboard (MAP) and in lieu providing new one piece pvc seat and back (Blowplast or equivalent) of chair as per specified in drawing including fixing material complete all as specified and directed by Engineer-in-Charge.

(b) Removing old unserviceable handboard of chair and in lieu providing new handboard made out of 18 mm pre-laminated particle board(Exterior grade) of size 600 x 300 mm with PVC edging shall be provided at all around the board with screwed to 25 mm hollow steel piece pipe to be inserted on 20 mm MS road welded to frame complete and including welding of steel frame the broken joints also painting with one coat of synthetic enamel paint shade blackwith providing four nos new hard rubber shoes to each chair complete all as specified and directed by Engineer-in-Charge.

Chair easy steel FD-121 (M) (a) Removing old unserviceable seat and S & F new seat made out of 12 mm thick plywood both side commercial upholstered with foam 32 density into 75 mm thick covered with leatherite raxian cloath of approved best quality to be fitted with MS screw with nut and bolts of required size of seat of 560 mm x 635 mm complete all as specified and directed by Engineer-in-Charge.

(b) Removing old unserviceable back and S & F new back made out of 12 mm thick plywood boath side commercial upholstered with foam 32 density into 75 mm thick covered with leatherite raxian cloath of approved best quality to be fitted with MS screw with nut and bolts of required size of back of 560 mm x 350 mm complete all as specified and directed by Engineer-in-Charge.

(c) M & L gas welding to chair easy steel frame where required by continuous welding around the broken joints and including painting with one coat of synthetic enamel paint black after preparation of old paint surface and also providing 04 nos new hard rubber shoes to each chair complete all as specified and directed by Engineer-in-Charge. Note:- (i) Cost of leatherite raxian cloth approved by GE/ Engineer-in-Charge, shall be in the range of Rs 150/- to Rs170/- approx per meter.

Almirah steel Large 1880x910x480mm (TP) (a) S & F in replacement of unserviceable three way locking device with new three way locking device complete including made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(b) S & F in replacement of unserviceable lock with new lock of 3 levers and ISI mark lock with double keys made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(c) S & F in replacement of unserviceable leg with new leg made out of 1 mm thick PBI sheet of size & shape as per existing complete all as specified.

(d) S & F in replacement of unserviceable MS cleat with new MS cleat to support shelf duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size including welding of broken shutter of almirah complete all as specified.

(e) S & F in replacement of unserviceable CP handle with new CP handle including nut, bolt & washer made of standard manufactures like Godrej or its equivalent. The cost of nut bolts and washers shall be deemed to be included in the quoted rates of this item.

(f) S & F in replacement of unserviceable shelves with new shelves made of mild steel sheet 1 mm thick duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size complete all as specified as approved/directed by the Engineer-in-Charge.

(g) Painting to steel surface of the almirah one coated by spray gun with synthetic enamel paint of Black shade after preparation of old painted surface complete all as specified and as directed by the Engineer-in-Charge .

Almirah steel Medium 1266 X 760 X 430MM (TP) (a) S & F in replacement of unserviceable three way locking device with new three way locking device complete including made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(b) S & F in replacement of unserviceable lock with new lock of 3 levers and ISI mark lock with double keys made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(c) S & F in replacement of unserviceable leg with new leg made out of 1 mm thick PBI sheet of size & shape as per existing complete all as specified.

(d) S & F in replacement of unserviceable MS cleat with new MS cleat to support shelf duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size including welding of broken shutter of almirah complete all as specified.

(e) S & F in replacement of unserviceable CP handle with new CP handle including nut, bolt & washer made of standard manufactures like Godrej or its equivalent. The cost of nut bolts and washers shall be deemed to be included in the quoted rates of this item.

(f) S & F in replacement of unserviceable shelves with new shelves made of mild steel sheet 1 mm thick duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size complete all as specified as approved/directed by the Engineer-in-Charge.

(g) Painting to steel surface of the almirah one coated by spray gun with synthetic enamel paint of Black shade after preparation of old painted surface complete all as specified and as directed by the Engineer-in-Charge .

Almirah steel 1266 X 760 X 430MM 1/2H 1/2S (TP) (a) S & F in replacement of unserviceable three way locking device with new three way locking device complete including made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(b) S & F in replacement of unserviceable lock with new lock of 3 levers and ISI mark lock with double keys made of standard manufactures like Godrej or its equivalent. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(c) S & F in replacement of unserviceable leg with new leg made out of 1 mm thick PBI sheet of size & shape as per existing complete all as specified.

(d) S & F in replacement of unserviceable MS cleat with new MS cleat to support shelf duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size including welding of broken shutter of almirah complete all as specified.

(e) S & F in replacement of unserviceable CP handle with new CP handle including nut, bolt & washer made of standard manufactures like Godrej or its equivalent. The cost of nut bolts and washers shall be deemed to be included in the quoted rates of this item.

(f) S & F in replacement of unserviceable shelves with new shelves made of mild steel sheet 1 mm thick duly painted with two coats of synthetic enamel paint of olive green shade with nuts, bolts of suitable size complete all as specified as approved/directed by the Engineer-in-Charge.

(g) Painting to steel surface of the almirah one coated by spray gun with synthetic enamel paint of Black shade after preparation of old painted surface complete all as specified and as directed by the Engineer-in-Charge .

Bar stool 300x300x750mm (TP) (a) M & L Tapestry/Fabric cloth over sythetic foam 25mm thick (as approved) for seat of bar stool revolving including taking out old worn out Tapestry/Fabric Cloth & Foam from stool and seat 12mm hot pressed plywood complete all as specified and as directed by Engineer-in-Charge.

(b) M & L as lifting hydrolic system of stool revolving including taking out unserviceable Gas Lifting Hydrolic System from stool complete all as specified and as directed.

Notice board (i) 1800 x 1200 mm (ii) 900 x 600 mm Removing the old u/s soft bd, baize green and wooden frame of notice bd and S&F the new baize green and soft bd, frame and finishing of wooden surfaces with french polish complete and of the following size. (a) Notice boad of size 1800 mm x 1200 mm

(b) Notice boad of size 900 mm x 600 mm

(d) All as per Srl item No 20.01 here-in-before but of size 900 mm x 600 mm

Chair dinning Cushioned /long back FD/E6/MAP/10 (R) (a) Replacement of seat cushioned 75 mm thick made of cool foam (Make : Sleepwell/ kurlon) of 32 density including ply wood 12mm thick suitable for seat duly covered with well finished best quality tapestry cloth not less than Rs 250/- meter shade and quality shall be approved by Engr-in- charge/GE.

(b) Replacement of front legs made of well seasoned sheesham wood duly plaine/smoothened after taking out the old unserviceable front legs

(c) Replacement of rear legs rest all as per item No 21.01 here in before

(d) Replacement of front and back rail well seasoned sheesham wood all as specified in drawings after taking out the old existing unserviceable rails

(e) Replacement of side rail well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable side rails.

(f) Replacement of back rail stiffner, side and middle stiffner well seasoned Sheesham wood all as specified in drawings after taking out the old existing unserviceable stiffners.

(g) S&F second class hard wood corner / bracket (L shape) of size 50mm x 50mm x 20mm thick fitted with screw between side rail to legs.

(h) Polishing all new and old surface with two caots of french polish after preparation of old surface complete all as specified.

Charpoy GI Pipe with Plywood top, FD-220 (i) Removing of unserviceable plywood from Charpoy GI Pipe, tightening/welding of loose long rails. Short rails, legs (i.e. complete charpoy) and supply and fixing the 12 mm thick 7 ply, commercial type BWR, exterior grade (water proof), ISI-303 marked of size 1980 x 900 mm fixed on top of GI Charpoy as shown on drawing with mild steel galvanized iron nuts & bolts of size 70mm x 6mm with GI washer (heavy weight) and three stiffner made out of MS flat iron 35 x 5 mm parallel to short rail duly painted black will be welded between the long rail (All as approved by GE and directed by Engr -in- charge.

(ii) M & L for electric welding of long rails, short rails, legs of 32 mm bore GI tubing by continuous welding around the broken joints duly painted with aluminum paint of welding portion all as directed by Engr-in-charge. Note :- (i) Unit of measurement of this item is 'Each' which shall comprise of welding of each broken joint all as specified above/directed by Engr-in-charge. (ii) Welding rods shall be ISI marked.

(iii) Painting to steel surface of the charpoy GI pipe one coated synthetic enamel aluminium paint after preparation of old painted surface complete all as specified and as directed by the Engineer-in-Charge .

Locker steel FD-1029 (a) S & F in replacement of unserviceable aluminium hasp & staple with new aluminium hasp & staple, 100 mm long, mild steel chromium plated (heavy duty) of locker bed side fixing with & including steel screws complete all as specified and as directed by the Engineer-in-Charge. The cost of steel screws shall be deemed to be included in the quoted rates of this item.

(b) S & F in replacement of unserviceable leg with new leg made out of 1 mm thick PBI sheet of size & shape as per existing complete all as specified.

(c) S & F in replacement of unserviceable aluminium handle with new aluminium D type handle (chromium plated) (heavy duty) 100mm long of locker bed side fixing with & including steel screws complete all as specified as approved/directed by the Engineer-in-Charge.

(d) Painting to steel surface of the locker steel one coated by spray gun with synthetic enamel paint of Black shade after preparation of old painted surface complete all as specified and as directed by the Engineer-in-Charge .

Hard Bed 1950x930x325 mm (TP) Supply and fixing the following new parts after removing broken parts including tightening with screw other members of bed complete all as specified ans shwon on drg. (a) Top ply 12mm thick of size bed hard complete 1950 x 900 mm. (BWR) as per IS-303 (07 ply) of commercial general purpose

(b) Long rail of shisham wood of size 100mm x 50mm x 1980mm.

(c) Fixing only shot rail after cutting to required length from old retrieved long rail.

(d) Ply wood 3mm thick teak faced to the direct vision of head rest and ply wood commercial 3 mm thick to other side including 4mm thick shisham wood edging all around.

(e) All as per srl No 24.03 (d) here-in-before but to foot rest.

(f) French polishing on surfaces of wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats.

Double Bed bunk (TP) Double Bed bunk of size 1980 x 900 x 1750 mm. Removing of unserviceable plywood from double bed bunk on both upper and lower top, Supply and fixing the 12 mm thick plywood sheet on upper and lower top suitable for double bed bunk as shown on drg. of size 1980 x 900 mm (BWR) as per IS-303 with mild steel galvanized iron nuts & bolts of size 70mm x 6mm with GI washer (heavy weight) and including electric welding of loose upper and lower frame, centre stiffener and cleat tube size of 50 x 100 mm x 6 mm of MS pipe by continuous welding around the broken joints and also replacement of old unserviceable above parts with new parts where required and also including painting with one coat of synthetic enamel paint (Black) after preparation of old painted surface complete all as specified and directed by GE/Engineer-in-Charge. Note :- (i) Cost of minor repair like welding to frame if required etc is deemed to be included in the quoted rate. (ii) Cost of all type nut bolts and washers and painting of the double bed bunk to be included in the quoted rate.

Meat & Milk safe 900 x 540 x 840 mm Removing old broken unserviceable parts of meat safe X PM Jali wire gauge, side and top and legs and suply and fixing wire gauge, leg and top of meat safe and making serviceable condition/functional and painting with one coat of synthetic enameled paint white including prewparation of surfaces complete all as specified and shown on drg .

Table Peg 450x450x400 mm Supply and fixing the following new parts after removing broken parts of well seasoned sheesham wood including tightening other parts with screw only of the table complete all as specified in drawing directed by Engr-in-Charge. (a) Table top new made of pre laminated particle board (exterior grade ) with teak face one side and other side white of size 450 x 300 x 18mm thick with 04 mm thick half raound teak wood beading shall be provided all round.

(b) Front and back rail

(c) Short rail

(d) Legs square & round type

(e) Short/long stiffeners

(f) S&F second class hard wood corner / bracket (L shape) of size 50 x 50 x 20 mm thick and fitted with screw between long rail to legs short rail to legs.

(g) French polishing on surfaces of wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats.

Teapoy wooden 600x450x540mm (TP) Supply and fixing the following new parts after removing broken parts of well seasoned sheesham wood including tightening other parts with screw only of the table complete all as specified in drawing directed by Engr-in-Charge. (a) Table top new made of pre laminated particle board (exterior grade ) with teak face one side and other side white of size 600 x 450 x 18mm thick with 04 mm thick half raound teak wood beading shall be provided all round.

(b) Front and back rail

(c) Short / side rail

(d) Legs square & round type

(e) Short/long stiffeners

(f) S&F second class hard wood corner / bracket (L shape) of size 75 x 75 x 20 mm thick and fitted with screw between long rail to legs short rail to legs.

(g) French polishing on surfaces of wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats.

Rack steel 1950x900x450mm Rubbing and removing dents, if any & then preparation of old painted steel surfaces with putty of rack steel and spray painting with one coat of olive green synthetic enamel paint to entire external and internal compete all as specified and as directed by Engineer-In- Charge

Table reading wooden 750x600x750 mm Supply and fixing the following new parts after removing broken parts including tightening with screw other members of the table reading complete and all as specified and shwon on drg. (a) Top of table made out of prelaminated particle board 18mm thick 1145 x 600 mm with 4 mm thick shisham wood beading all around.

(b) Cabinet of table

(c) Drawers of table.

(d) Shutter of table of size of 570mm x 405mm made out of 18mm thick prelaminated particle board including piano type hinges 40mm wide.

(e) Leg of table of 1st class shisam wood size of 45 x 45 x 750mm.

(f) Foot rest of table of 1st class shisam wood size of 50 x 25 x 1025mm.

(g) Aluminium anodized knob 25mm of best quality.

(h) Lock shall be of brass multipurpose 4 lever with duplicate key size 40 mm as shwion on drg.

(j) S&F second class hard wood corner / bracket (L shape) of size 100 x 100 x 25 mm thick and fitted with screw between long rail to legs short rail to legs.

(k) French polishing on surfaces of wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats.

Table 3’ x 2 ‘ (900 x 600 x760 mm) with drawer Supply and fixing the following new parts after removing broken parts of well seasoned sheesham wood including tightening other parts with screw only of the table complete all as specified in drawing directed by Engr-in-Charge. (a) Table top new made of pre laminated particle board (exterior grade ) with teak face one side and other side white of size 900 x 600 x 18mm thick with 04 mm thick half raound teak wood beading shall be provided all round.

(b) Long rail

(c) Short rail

(d) Legs square & round type

(e) Short/long stiffeners

(f) S&F second class hard wood corner / bracket (L shape) of size 100 x 100 x 25 mm thick and fitted with screw between long rail to legs short rail to legs.

(g) Drawers complete as per drg

(h) French polishing on surfaces of wood of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats.

M/S CHANDER SHEKHAR