Signal & Telecom work in connection with (1)Ukai songadh - Jalgaon - TRR(P) - 3.00 Tkm & TSR(P) - 21.640 Tkm (2) Udhna - Ukai songadh - TRR(P) - 0.89 Tkm and TSR(P) - 10.13 Tkm.(3) Jorasavan-Ukai songadh-Providing RGM Siding facilities at Maroli, Chalthan, Madhi & Ukaisongadh (4) Valsad:Extension of middle FOB (75Mx6.1M) to west side ,and providing new FOB at North end connecting PF 2/3, PF 4/5 to west side at Km 198/16-18 of Udhna-Jalgaon and Virar-Surat section of Mumbai Division.

A-Supply & Execution Portion/Ukai Songadh-Jalgaon-TRR(P)-3.00Tkm &

G.I. Bonding wire soft for track circuit bonding 8 S.W.G. (4mm Dia.) or as per instructions of Engineer In-Charge.

Channel Pins MS(Galvanized) single roove, 7 mm suitable for 4mm dia bonding wire as per spec No IRS S 17 & RDSO Drg No. S-69/M.

Drill bits 7.2 mm or as per instructions of Engineer In-Charge.

Drill bit 16 mm or as per instructions of Engineer In-Charge.

Drill bit 12 mm or as per instructions of Engineer In-Charge.

Drilling of holes of different sizes in rails 7.2mm/12mm/16mm/22mm as per instructions of Railway Engineer incharge.

Provision of bonding of GI wire 8 SWG with drilling of holes or or as per instructions of Engineer In-Charge.

Maintenance of Track mounted equipments like S&T fitting on turn outs including different activities during BCM/TTM/TRR works as follows:- Specially opening and refixing of DC-TC jumpers/AFTC jumpers / Axle counter, transducers during different Engg. works Opening of DC-TC 8 /AFTC jumpers /axle counter transducers digging work from rail to TLJB /TMU /0 bond /location is required to be done as per site requirement also after refixing of DC-TC /AFTC jumpers /Axle counter transducers needs to be buried in proper depth. It includes drilling hole in rail as per site requirement. Also includes fixing of mateiral like 7 strand bonding wire, cannel pin taper pin as oer site requireemnt fixing of nut bolt if required The team to be provided for this work should comprise of : Fitter- 1 Nos., Blacksmith 1 Nos. Mason/Carpenter- 1 No. and Helpers-5 Nos. also it include any work of EOLB or sliding boom and earthing arrangement of Signalling gears. Any other work as per instruction of Railway Engineer. All T&P & Jigs required to execute the work will be supplied by the contractor.

B-Supply & Execution Portion/Udhna-Ukai Songadh-TRR(P)-0.89Tkm and

G.I. Bonding wire soft for track circuit bonding 8 S.W.G. (4mm Dia.) or as per instructions of Engineer In-Charge.

Channel Pins MS(Galvanized) single roove, 7 mm suitable for 4mm dia bonding wire as per spec No IRS S 17 & RDSO Drg No. S-69/M.

Drill bits 7.2 mm or as per instructions of Engineer In-Charge.

Copper Lugs 16 Sqmm for power cable or as per instructions of Engineer In-Charge.

Copper Lugs 25 Sqmm for power cable or as per instructions of Engineer In-Charge.

Copper Lugs 35 Sqmm for power cable or as per instructions of Engineer In-Charge.

PVC tube for bootleg outside dia 15mm, inside dia 11mm thickness 2 mm 50 mtrs each coil or as per instructions of Engineer In-Charge.

Supply of wheel detection sensor with 10 metre cable for Siemence MSDAC.

Supply of Reduction plate 60 kg (Siemens MSDAC system)

Supply of L- Sensor Clamp for Siemens MSDAC system

Copper bus bar 200x25x6mm(SEEB) to terminate earth rod as per STS/E/TAN/3006 ver 3.0 or Latest.

Copper bus bar of 150x25x6mm (SEEB) as per STS/E/TAN/3006 ver 3.0 or Latest.

Copper bus bar of 300x25x6mm (MEEB) as per STS/E/TAN/3006 ver 3.0 or Latest.

Switch plate Lubricant, High Performance Slide Chair Lubricant With Excellent 14 Corrosion Protection Colour - Black,) Appearance Semi Fluid,Thickener Type Inorganic, Penetration 450-470, 4 Ball Weld Load 315kg, 4 BallWear Scar 0.60mm, Temperature Range -30C To 80C, Packing of 12.5 Kg PailBox.

Supply of Nylon Insulation for Thick Web point machine, consist of Insulating. (1) plate- 02 Nos . as per RDSO Drg. No-S-34041(2) Nylon Insulation bush-8 Nos , as per RDSO Drg. No- (a) S32199-04 Nos . (b) S-8813-04 Nos , (3) Nylon Insulation Washer 08 Nos, as per RDSO Drg. No. (a) S8640/1-04 Nos . (b) S-8640- 04 Nos. 2) Through rod Insulation = 1 no Bush(RDSO Drg No. CSE8640/1, 2 nos Washers (CSE8640/2) 3) Lock slideInsulation -2 nos Bushes (RDSO Drg No- CSE 8640/A) 4 nos Washers (RDSODrg No. CSE-8640/1). 4) Detection slide insulation =2 nos Bushes (RDSO Drgno. 8641/A), 4 nos Washers (RDSO Drg No-8640/1). 5) SSD Insulation Rod =1no. Plate (RDSO Drg No S325/M), 2 nos . Bushes (RDSO Drg No-T10372), 4nos. Washers (RDSO Drg No T- 10371). 6) SSD Insulation in Rail 1 no . Washer(RDSO Drg No washer : S8640) 1 no Bush (RDSO Drg No S8641/A) 7) Pbracket Insulation :- Insulation Plate 01 (RH) RDSO Drg No: S3265 Insulation Plate = 01 No (LH) RDSO Drg no. S3266 , Insulation Bushes=04 nos. RDSO Drgno S23199 Insulation Washer : 04 nos . RDSO Drg no. S8640.

Torque wrench with reversible ratchet, 10-50 Nm with preciosn +/- 3% Make :- WERA, Gedore, Stahwille, Snapon

Drilling of holes of different sizes in rails7.2mm/12mm/16mm/22mm as per instructions of Railway Engineer incharge.

Drilling of holes( 6 to 25 mm) as per instruction of Engineer in-charge

Refixing of electrical point machine, ground connection during phase working (Non 19 interlocked working) after removing the existing fitting if any, adjustment if necessary, cable termination, wiring , testing and commissioning of electrically operated point, fixing and connecting point indicator on derail switch if necessary. The work shall be done as per extant practice on WR & the instruction of Railway Engineer at site

Execution of S&T work related to engineering block, Track mounted equipments like S&T fitting on turn outs including different activities during BCM/TTM/TRR works as follows:- Specially opening and refixing of DC-TC jumpers/AFTC jumpers / Axle counter, transducers during different Engg. works Opening of DC-TC /AFTC jumpers /axle counter transducers digging work from rail to TLJB /TMU /0 bond /location is required to be done as per site requirement also after refixing of DC- 20 TC /AFTC jumpers /Axle counter transducers needs to be buried in proper depth. It includes drilling hole in rail as per site requirement. Also includes fixing of mateiral like 7 strand bonding wire, cannel pin taper pin as oer site requireemnt fixing of nut bolt if required The team to be provided for this work should comprise of : Fitter- 1 Nos., Blacksmith 1 Nos. Mason/Carpenter- 1 No. and Helpers-5 Nos. also it include any work of EOLB or sliding boom and earthing arrangement of Signalling gears. Any other work as per instruction of Railway Engineer. All T&P & Jigs required to execute the work will be supplied by the contractor.

Exothermic welding in relayroom ,IPS or any indoor roomas per STS/E/TAN/3006 ver 3.0 or Latest.

Exothermic welding for any outdoor Work for earth connection as per STS/E/TAN/3006 ver 3.0 or Latest.

Skilled man power to be provided by contractor for Engg. JCBs working to provide marking & supervisory work for the S&T cables during digging work by JCB's and repairing /restoring/jointing of cables, if damaged Cables & Joints Material will be provided by railway. While Chuna marking will be done by his/her Chuna will provided by contractor information for deputing 23 skilled man power for above work will be provided by Railway Engineer incharge before 24 hours from commencement of digging by JCBs. They will check cables route by Cable route tracer and will do chuna marking and will show the cables (on rough sketch) available in a small length approximate 50-100 meters of digging. Note: Minimum two man will be provided at a time including Cable jointer, they will stay whole time during JCB digging work. (The CV to be got approved by Railway).

C-Supply & Execution Portion/Joravasan - Ukai songadh - Providing RGM

Blowing and drawing of OFC through laid HDPE duct as per approved route plan , taking due care while transporting and sealing both ends as per specifiaction in tender documnets.

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003 or latest alongside the track in normal (all type) soil/strata, conforming to distances as per cable route plan and refilling. This 2 work includes clearing of route from bushes etc, covering of cable laid in trench by loose soil for a layer of 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Western Railway and instructions of Railway Engineer at site. In case 1.2m depth of trench is not achievable due to site conditions, specific approval of JA grade officer will be required for each site where trench depth of 1.2m is not possible. Without the approval of JA Grade officer, no payment for trenching will be made for trench depth less than 1.2m. Running

Horizontal direction drilling/boring without damage of surface road /track using Auger Machine(HDD machine). The bore shall be upto 200 mm dia & shall be done at the depth of 3 minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank height of the bank of the road. The length of the bore shall be minimum 4 Mtrs long. This include insertion of different dia DWC-HDPE pipe/ GI pipes coupling etc. as per direction of Engineer In charge. Note:- Pipe Supply is not covered under this item. Contactor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable.

Supply of Double Walled Corrugated (DWC) HDPE Pipe/duct with associated collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti-rodent & anti-oxidant and non flame propagating type in 6 meters straight length and of size 120 mm outer dia,& 103.5 mm inner 4 dia. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also be supplied with each pipe as per the site requirement. 1) Suitable snap fit coupler with rubber O- Ring 2) Spacers 3) Tees 4) Bend, 5) End-cap (The total quantity of above items is equal to no. of pipes supplied.) DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified.

Placing of DWC HDPE/RCC/GI pipes along with collars in trenches at places near track and road, crossings, platform cuttings etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(Unit is RM running meter.)

Supply of Pre-lubricated HDPE duct, 40 mm OD, 33 ID as per RDSO specification No. 6 RDSO/SPN/TC/45/2013 Rev. 2.0 or latest. The item also includes supply of all the accessories of HDPE duct like end caps, collars, bends, couplers etc. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board.

Laying of HDPE pipe duct in trenches/GI Pipe/RCC pipe/on wall/on PF, including jointing and levelling using couplers and sealing the section etc as per site requirement as per specification in tender document.

Supply of RCC cable route marker engraved and painted on both side along the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker.

Transportation at site and Installation of RCC cable route marker engraved and painted on both side along the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker.

Supply of 48 fiber OFC optic fiber splice straight joint enclosure (SJC) complete. As per specification in tender document.

Splicing of OFC cable and making the SJC splice joint in dust free environment. As per specification in tender document.

Supply of Fiber Distribution management (FDMS) of 48 fiber OFC as per RDSO specification in tender documnet.

Installation of Fiber distribution management system splicing and termination of 48 fiber OFC cables. As per specification in tender documnet.

Supply and execution of Rapid Joint LS3 suitable for cable Jonting of cable of various size, having dielectric strength > 20KV/mm, Non Toxic, low viscosity, Flamability point > 200 C, Re- entrable, Long storage life Make RAYTECH or Similar. Cable size 4/6 Quad

Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes/ Trunking. This also includes laying of cables in track crossings & road crossings. Item 15 includes provision of labels of coloured plastic adhesive tapes or any other identifiable material on each cable to give the cable number at each Gantry Post/hectometer post.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes.

Cement concrete work for miscellaneous items in the ratio 1 : 3 : 6 . Item includes excavation, ramming, curing and plastering with cement & sand mixture (aggregate not exceeding 3.8 cm.) (Aggregate cement & sand to be supplied by the contractor).

Supply of VF Transformers (2T/3T), 1120/470 Ohms as per RDSO Spec. No. IRS: TC- 76-2000 with Amnd. 1 or latest for emergency joints in 6-Quad Cable.

Supply and installation of OFC jointing pits size 0.6m X 0.8X 1m. The material shall be supplied as per engineer in charge instructions. As per specification in tender document.

Digging of cable pit (min 2x2x1m) as per instruction of Site Engineer, supplying and filling of sand before and after coiling the cables, covering top of the cable pit with stones and providing brick masonry on all four sides of the cable pit and plastering thereafter.

D-Supply & Execution Portion/Valsad - Extension of middle FOB

Supply of Armoured Optical Fiber Cable, 6 Core, Single Mode as per specification in tender documnet.

Laying of 6 core OFC through PVC Pipe/Casing capping and termination/splicing in LIUs/FDMS as per specification in tender document.

Supply & installation of 24 port Rack mounted LIU along with all accessories as per specification in tender document.

Supply & installation of 12 port Rack mounted LIU along with all accessories as per specification in tender document.

Installation of Rack mountable LIU including splicing and termination of fiber in LIU as per specification in tender document.

Supply of Fiber Distribution management (FDMS) for 48 fiber OFC as per RDSO specification in tender document.

Installation of Fiber distribution management system splicing and termination of 48 fiber OFC cables. As per specification in tender document.

Supply of underground PIJF 20 pair cable , 0.5 mm dia as per latest RDSO specification in tender document.

Laying of Jelly filled cable in trench/open ground/under asphalted/cemented surface/through pipes/through wall/through rail track, including laying material as per specification in tender document.

Supply of STP CAT-6 Cable as per specification in tender document.

Supply of UTP CAT-6 Cable as per specification in tender document.

Supply of Three Core PVC Power Cable as per as per specification in tender document.

Supply of 2 core 1.5 sqmm PVC insulated loudspeaker cable as per specification in tender document.

Supply and installation of 19" 42U rack with accessories as per specification in tender document.

Supply of PVC rigid pipe 25mm dia with ISI mark & reputed make as per specification in tender document.

Laying of PVC/Coaxial cable/Power cable/CAT6 cable in through PVC casing capping/pipe on wall including laying material like 3 way/4 way junction box ,T-Joint, flexible PVC pipes etc as per specification in tender document.

Cutting of the platform surface (Tile/Slab) for a depth of 25cm and a width of 10cms and refilling/ Reconditioning/ Concerting/ Repairing the platform after laying DWC/HDPE pipe and 17 cable. Cutting should be done with marble cutting machine in proper manner and restore the same as before in such a manner that aesthetic of the platform is not disturbed including provision of special tactile tiles for Divyangjan, etc. railway guidelines. Item as per specifications in Chp. 4 of Tender document.

Skilled man power to be Skill provided by contractor for Engg. JCBs working to provide marking & supervisory work for the S&T cables during digging work by JCB's and repairing /restoring/jointing of cables, if damaged Cables & Joints Material will be provided by railway. While Chuna marking will be done by his/her Chuna will provided by contractor information for deputing 18 skilled man power skill for above work will be provided by Railway Engineer incharge before 24 hours from commencement of digging by JCBs. They will check cables route by Cable route tracer and will do chuna marking and will show the cables (on rough sketch) available in a small length approximate 50-100 meters of digging. Note: Minimum two man will be provided at a time including Cable jointer, they will stay whole time during JCB digging work. (The CV to be got approved by Railway). Running

Supply & Placing Double Walled Corrugatd (DWC) pipe with asiociated collars etc. as specification No IS 14930 parl I & II or latest anti-rodent & anti-oxidant and non-flame propagating type in 6 meters straight length and of size 120mm outer dia & 103.5mm inner Dia. As per specification in tender document.

Supply of Indiana/phoenix/Jiwei or better make perforated cable trays with yellow 20 powder coating and standard perforation fabricated from 1.6 mm thick pre-galvanized sheet in the standard length of 2.5 mtrs, with couplers, plates and electro galvanized hardware. Size: 300 mm width X 50 mm height. Item should be as per specifications in Chp. 4 of Tender document.

Fixing of cable tray for housing of all type of telecom cables as per specifications in Chp. 4 of Tender document. Any and all required accessories must have rust-proof GI coating. Vertical reducers, tees, joint accessories to be provided wherever required as per site requirements.

Supply & Fixing of 100 mm dia GI pipes to carry all the cable at the cabins, Stations, cable huts & other buildings, FOBs etc. as per specifications in tender document.

Cement concrete work for miscellaneous items in the ratio 1:3:6. Item includes excavation, ramming, curing and plastering with cement & sand mixtures (aggregate not exceeding 3.8cm). (Aggregate cement & sand to be supplied by the contractor.)

Supply of RJ45 connector as per specifications in tender document.

Releasing of PVC/Coaxial cable/6core OFC/ Power cable/CAT6 cable from station 25 platforms/ building walls etc. incuding its laying materials & transporting them to nearest S&T office or DS8 depot or as decided by the supervisor in charge as per specification in tender document.

Supply and installation of 19" 6U rack with all accessories as per specification in tender document.

Supply of Optical Laser Torch as per specification in tender document.

Supply of RJ45 connector Crimping Tools as per specifications in tender document.

Supply of Remote Craft Terminal as per specification in tender document.

Supply and Installation of Control IP Telephones with Hands Free and Gooseneck Operation for Wayside Stations as per RDSO/SPN/TC/99/2012 latest version, compatible with current setup and as per specifications in tender document.

Supply, transportation, installation, integration of 8 TB Hard Disk compatible to enhance the storage capacity of NVR. Make: SEAGATE PLUS/WD/Samsung or similar.

Supply of Bi-Di SFP 1 Gig Single mode as per specification in tender document.

Supply and installation of 8 port manageable PoE switch with 2 SFPs as per RDSO specification RDSO/SPN/TC/83/2020 Rev. 2.1 and as per specifications in tender document.

Supply & installation of Layer 2, 24 port Manageable switch as per RDSO specification RDSO/SPN/TC/83/2020 Rev. 2.1 and as per specifications in tender document.

Supply of Single mode LC-LC/LC-SC/SC-SC optical patch cord as per specification in tender document.

Supply of factory crimped CAT6 patch cord , 1.0 m length of reputed make as per specification in tender document.

Supply of factory crimped CAT6 patch cord , 2.0 m length of reputed make as per specificationin tender document.

Supply of 20 Mtr. HDMI Cable coil as per specifications in tender document.

Supply of casing capping of size 150 mm x 50 mm as per specification in tender document.

Supply, Installation, Integration, Testing and Commissioning of Train Formation At a 40 Glance Display Board with all accessories as per latest RDSO Specification No. RDSO/SPN/TC/108/2019 latest version latest amd. and compatible with existing system and as per specifications in tender document.

Supply of Aluminium weather resistant column speaker 20 watt & its installation as per specification in tender document.

Supply of hand held optical power meter as per specification in tender document.

Supply, Installation, Testing & Commissioning of 2 MP Full HD Resolution Fixed Bullet 43 type IP Colour Camera with memory card, protection box and all other accessories as per RDSO specification No. RDSO/SPN/TC/65/ 2021 version 6.0 or latest and as advised by site incharge and as per specifications in tender document. It should be compatible with existing system and integration to be done as per requirements including licenses, software, etc.

Supply of 8 Channel NVR with 1 TB storage capacity as per latest RDSO specifications including all necessary software/license like VMS, etc. Transportation, Installation and 44 commissioning of NVR with hard disk and complete CCTV surveillance system and it also should be tested for 2 Hrs. or as advised by site incharge. It should be compatible with existing system and integration to be done as per requirements. Item as per specifications in tender document. Note: Multilingual Banner of size 18"x18" to be fixed stating area under surveillance or as per consignee.