Provn of one Gd Room with watch tower for one Hav and three OR at SASF, Odianwali and special repair to bldg No P-322 at Mil Stn Fazilka

Amount

SCHEDULE 'A' SECTION I (B&R Portion)

Surface excavation n.exc 30cm deep & averaging 15cm deep and getting out in soft / loose soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Excavating in trenches, exc 1.5m wide & n exc 3m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & n exc 1.5m in depth & getting out in soft/loose soil

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required

M&L PCC in foundations, filling and mass-concrete type D2(1:4:8)using 40 mm graded stone aggregate

Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6)

S&F 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork ,applying evenly a coat of blown type bitumen at the rate of 1.5kg/per sqm and binding with clean dry sand @ 0.05 cum per sqm, polythene film, 150 micron thick,laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sq.mtr complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M&L RCC M-25 design mix using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts

M&L RCC M-25 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L RCC M-25 design mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L RCC M-25 design mix using 20 mm graded aggregate in Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings

M&L RCC M-25 design mix using 20 mm graded aggregate in chajjas ,shelves and the like

M&L RCC M-25 design mix using 20 mm graded Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat

Formwork to sides of pillars, posts, struts, piers, columns, & stanchions Rough finished surfaces of concrete Square, rectangular or polygonal

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat

Formwork to staircases with sloping or stepped soffits including risers and stringers Rough finished surfaces of concrete

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter Rough finished surfaces of concrete

Formwork to chullah hoods, chajjas, troughs and similar items including edges Rough finished surfaces of concrete

M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

M&L Mild steel TMT bars 6 to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs n exc 20 cm wide & sides of RCC/PCC bands in walls, horizintal or sloping & similar work exc 10cm but n exc 20cm wide Roughed finished surface of concrete

Hardcore of Broken brick bats n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M&L 50mm thick PCC type C-1, (1:3:6) using 20mm graded stone aggregate Finished even & smooth without using extra cement as in plinth protection

M&L continuous brick edging, with burnt clay bricks of sub class ‘B’ (old size) with width equal to the depth of the brick laid dry on end vertically including sand cushioning & filling interstices with sand (Tibba sand) complete all as specified.

M&L, 15mm thick rendering in CM 1:6 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling

M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) finished even & smooth (without using extra cement)

Applying three coats of white wash on new Ceiling surface including preparation of surface.

Applying three coats of white wash on new wall surface including preparation of surface.

Applying two coats of cement base paint, white or tinted on new wall surface including preparation of surface.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified size of frame 125X60mm all as specified .

S & F Flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides as per SSR Part – I all as specified.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified .

S & F galvanised mild steel wire cloth, 0.51 mm to 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples,fixed in repairs all as specified .

Supply only Butt hinges 100mm size, medium weight, cold rolled mild steel.

S & F 150mm Extruded aluminium alloy handles, fabricated all as specified.

S & F Alum anodized barrel tower bolt of extended section and fixed 200 mm long.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section.

S&F Aluminium handles 125mm size, cast type, anodised

S & F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixe

S&F in steel window 1.25 mm thick box type (primer coated) ERW hollow "P" section of size 60mm x 25mm single rebated comprises guaged and glazed skeleton shutter ERW section 50mm x20mm and 1mm thick with two openable leaf consisting two no. of sash bars of flat iron 12mm x 3mm complete welded to frame and all description as directed by Engg-in -charge

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complet

S&F Framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars & similar work conforming to Fe 410-0 or Fe 310-0

S&F Sheet glass 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane

Applying two coats of synthetic enamel paint on wooden surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome

M&L 100mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate)

M & L Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbingand polishing complete including 15 mm thick sceeed bed or bedding in CM 1:4

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4)

S&F Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 15mm thick plaster in CM(1:4)

Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr /10 sqm with a thickness of 650micron Note: 6 Hrs interval between two coats will be maintain& the work will be carried out through company applcator duly got approved from Accepting officer in writing before incorporation and paid only after receiving of the warrenty certificate from the company.Make : Asian paint or equivalent as approved by GE

S&F Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe)

S&F PVC valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity Make:- slimline / Paryware

S&F Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets, CP, brass, Waste fittings 32mm bore & PVC Waste Pipe 32 mm bore

S&F CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe

S&F Angle Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F brass CP shower rose fancy type of fixing with 15mm pipe.

S&F Bib taps fancy type 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule

S&F Stop valves 15 mm bore concealed type,with long shank cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity

S&F Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F Ball valves PTMT 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule

Supplying and laying of CPVC pipes 25mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supplying and laying of CPVC pipes 20mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with acces door

S&F 75mm PVC (SWR) vent cowl

S&F 110mm PVC (SWR) 'P’ trap

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

Material and labour DWCPE pipe 150 mm dia ( 160 mm OD) completed laid in trenches including earthwork, removal and return filling and jointed including testing alongwith necessary jointing material tees/union/socket etc complete laid on PCC bed 150mm thick PCC in 1:3 type C2 of avg depth 0.90 to 1.65 m depth incuding packing under and haunching against the side of pipes after they are laid and tested all as specified in IS 16098:2013 and as directed.

M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate

Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4)

M&L PCC in surface channels and drains type B1 (1:2:4) using 20 mm graded stone aggregate

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extgra cement including forms, moulds mitred/stopped ends etc.

M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) mixed with water proofing compound 3% by weight of cement finished even & smooth without using extra cement ( WPC shall be measured & paid separately)

M&L Rendering 10mm thick on fair face of brick work/concrete surfaces in CM (1:4)

M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:6) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces

Providing & laying On site Hume Pipe septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 5user

Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 2.4M dia X 3.0M effective deepth including removing excavated soil n exc. 150m & depositing where directed at a level n exc. 1.5 m above the starting point all as directed by Engineer- in - Charge.

Taking down chowkats with shutters (without taking off shutters from the frame exceeding 1.50 sqm each but not exceeding 4 sqm) removing to store

Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified.

S & F 100 mm long butt hinges extruded alumiunium alloy with galvanised mild steel hinges pin, anodised and fixed.

M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified.

S&F powder coated anodized aluminum frame for doors, windows , ventilators with one of more rebates including joining cleat for fixing etc. completed all as specified.

S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by GE. (ii) Three track bottom – Jindal main – 2010 section 20620 or equivalent as approved by GE. (iii) Shutter Vertical Section - Jindal main – 2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom - Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 or equivalent as approved by GE.

S&F powder coated aluminum windows and ventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified.

S&F aluminum anodized grill diamond shape 100mm x 100mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised complete all as specified

Dismantling of brick wk built in cement mortar

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

Supply only liqid water proofing compound.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L glazed ceramic tiles 450X 300X 7mm colour tiles on walls etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the work over 10 mm rendering in CM 1:4.all as specified.

M&L marble work 18 to 20 mm thick in single piece (table rubbed and polished) in steps, jams, pillars, windowcills,cooking platforms and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed by Engineer-in-Charge.

M&L marble work 18 to 20 mm thick in single piece in riser of steps, skirting , dado, and pillar laid and jointed in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed by Engineer-in-Charge.

M&L Granite (of any type) tiles 18mm - 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick rendering in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks and removing to store of 500 ltr capacity

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm.

S & F Vitreous china white OVAL wash basin of size 550 x 400 mm including brackets, waste pipe and waste fitting 40 mm brass chromium plated and waste pipe and 15 mm dia PVC connection with brass nuts as in repairs complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan padestel pattern white including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

S&F grating square 100 mm dize of PTMT (minimum weight 25 gms)

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.

Tacking down eaves gutters and ran water pipes

PVC (SWR) pipes 110 mm single socketed in any length with rubber ring joints fixed to walls allas specified and dircted.

S&F PVC (SWR) bends 110 radius complete all specified and directed.

Dismantling of CI pips or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed.

S&F Cast iron soil 100 mm bore , waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors

Dismantling of CI pips or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed.

S&F Cast iron soil 75 mm bore , waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors

S&F in repairs 75mm bore Cast iron cowls, all as directed.

S&F in repair bib taps cast copper alloy screwed down crutch or buttefly handle screwed both ends for iron pipe brass ferrrule of size 15mm bore.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by Engr-in-charge.

S & F brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed. Make : Prayag.Essco and equivalent.

S & F in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15 mm dia steel pipe or union.

S&F in repair towel rail 20mm dia, D type 60cm long between flanges brass bran chromium plated. Make -hindware. Esser etc equialant.

S & F in repairs, soap dish chromium plated brass complete all as specified and directed by Engineer-in-Charge.

S&F PVC waste pipe 32mm dia & 90 cm long Complete all as specified and directed.

S & F Waste coupling for 40 mm bore dia. of discharge pipe PTMT (half or full threaded) . Minimum weight 45 gms.

M&L Old srface Complete removal of existing treatment on walls and applying two coat of cement base paint including preparation of surface complete all as specified and directed

M& L prepared of old plastered surfaces applying three coat of white wash on celling.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper then applying two coats of oil bound distemper over one coat of cement primer including all as specified.

M & L Preparation of Old plastered surfaces by removing old treatment with hand electric grinder then applying two coats of interior grade wall putty and making it smooth with sand paper then applying two coats of oil bound distemper over one coat of cement primer including all as specified.

S&F 25 mm dia drapery curtain road with decoative end knobs complete with brackate and fixed to walls complete all as sp & dir .

M & L 75mm thick PCC 1:4:8 , type D- 2, using 40mm graded aggregate as in sub base all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block with grey cement & pigment, any shape and size confirming to IS 15658-2006 of 80mm thick M-40 grade including and over 25mm thick sand cushion.

M & L PCC 1:2:4, type B-1 , using 20mm graded stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work all as specified and as directed.

SCHEDULE 'A' SECTION-II (E&M PORTION)

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as sockets, ceiling roses, pendants batten holders regulators socket, call bells & making good to the disturbed surfaces of walls, matching the colour with existing Surface all as spd and directed by Engr-in-Charge. Note: Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable main switches and MCB distribution boards single phase complete all as spd

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code ISI marked and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/exhaust fan controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified (Cost of MS sunken box and bakelite sheet included in the rate).

All as per Srl item No. 158 here-in-before but one three pin socket outlet 5 Amps on the independent board complete all as specified.

All as per Srl item No.158 here in before but with 1.5 Sqmm (nominal area) PVC insulated multistranded copper conductor cable unsheathed ISI marked controlled by two way switches complete all as specified.

S&F switch Piano type single pole one way 5 Amp,230 VAC supply.

S&F switch Piano type single pole two way 5 Amp,230 VAC supply. .

S&F socket two in one ,3 Pin 5 Amps 230 VAC supply, .

Supply & fixing PVC Lamp holder suitable for and including batten fittings ,LED Electric lamp 9 Watt with backalite 20mm back plate complete all as specified & directed, .

M&L for Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed.

S&F of fan regulator step down electronic type heavy duly flush type 230 volts AC single phase fixed on laminated sheet top cover (laminated top cover is included in point wiring) and connecting up complete all as specified and directed. (Laminated sheet top cover and sunken box is included in point wiring).

S & F of MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 6 to 32 Amps all as specified and directed.

S & F of MCB suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA and 16 to 40 Amps all as specified and directed.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 4way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 2 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

M & L for Sub main wiring with 2 single core 4 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 4 Sqmm single core copper earth wire complete all as specified. (Note:- Three lengths of 4 sqmm cable and will be measured as one length).

Excavation in trenches, not exc 1.5 m wide and n. exc 1.5 m depth; or n exc 10 Sqm on plan and n exc 1.5 m in depth for foundations of poles, struts, stays etc. or laying underground cable etc. in soft/loose soil, & getting out complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and directed by Engineer-in-Charge

Removal of excavated surplus soil to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge .

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable all as specified and directed by Engineer-in-Charge.

Supply and laying, & testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured,electrical power cable (heavy duty) with stranded aluminium conducter ,1100 volts grade of Size 10sq mm 2 core

All as per Srl item No. 158 here-in-before but one three pin socket outlet 5 Amps on the same board complete all as specified.

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable ISI marked in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified.

S&F switch Piano type single pole one way 15 Amp on laminated sheet top cover complete to all as spd (Sheet top cover incl in point wiring) .

S&F socket Pinao type 6 Pin 16 amp,230 VAC .

S&F of Ceiling fan of 1200mm sweep mounted in suitable arrangement for operation on 230 volts, single phase, 50 cycle per second, AC supply with electonic type regulator and connecting accessories BEE 5 Star rating and connecting up including three core PVC insulated PVC sheated copper conductor flexible cable from ceiling rose to fan fixing in ceiling complete and making the surface good after fixing the fan complete all as specified and directed. MAKE : BAJAJ/HAVELLS/CROMPTON

Supply and fix electric water heater, storage type steel body with heating element 1.5 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as angle cock, hot and cold pvc pipe, 15 Amps Plug top complete all as specified and directed by Engr-in-Charge.

Suppy and fixing Exhaust fan metalic body heavy duty of size 300 mm sweep with louver shutter 220V, single phase AC including 1.0sqmm copper flexible cable twiested three core alongwith flelxible PVC condiut from ceiling rose to fitting testing complete all as specified and directed including cutting holes thruogh cement mortor wall for fixing 300mm sweep exhaust fan grouting the bolts, plastering and making good surface internally and externally wth existing colour.Make:Cromption/Havells/Bajaj

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 8 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

M & L for Sub main wiring with 2 single core 6 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 6 Sqmm single core copper earth wire complete all as specified. (Note:- Three lengths of 6 sqmm cable and will be measured as one length).

Supply and laying, & testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured,electrical power cable (heavy duty) with stranded aluminium conducter ,1100 volts grade of Size 16sq mm 2 core

Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 25 mm dia bore.

Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 20 mm dia bore.

S & F stop valve size 20 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.

S & F stop valve size 40 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.

KATARIA CONSTRUCTION