Construction of JNV at Port Mout

Amount

Extra for carraige of earth by means of mechanical transport within a lead of 1.0km including loading unloading stacking, etc as per the direction of Engineer incharge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.

Ordinary rock

Supplying and filling in plinth with Pulverised sand under floors including, watering, ramming consolidating and dressing complete.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m.

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size).

1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 40 mm nominal size).

1:5:10 (1 cement : 5 coarse sand(zone-III) : 10 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(Zone III) : 4 graded stone aggregate 12.5mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of 40 mm aggregrate nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Weather shade, Chajjas, corbels etc., including edges

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.

50 mm thick

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing sheet covering over expansion joints with iron screws as per design

Aluminium fluted strips 3.15 mm thick.

150 mm wide

200 mm wide

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.

300 mm wide.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete :

20 mm dia.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Single rubber stopper

Twin rubber stopper

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

30 mm thick plain PVC door shutters.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineerin- charge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together.

Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer's specification and direction of engineer-in-charge.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 3.5 sqm_ 1500x2100mm).

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :

4.0 mm thick glass panes.

5.5 mm thick glass panes.

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey cement.

Dark shade pigment using ordinary cement.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying antiskid Ceramic floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours shadesw except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement :4 Coarse sand) including pointing the joint with white cementte cement and matching pigment etc.,., complete.

Extra for providing and fixing wind ties of 40x 6mm flat aluminium section.

Providing and fixing plain multipurpose cement board (High pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid separately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i)Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.

Coupler

Single pushfit Coupler :

Single tee with door

Single tee without door

110 mm bend

Shoe(plain)

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing at all heights, levels and locations Aluminium profile industrial troughed sheet of Alloy 31500/ 31000/ 40800, conforming to IS 1254, IS 737, IS 2676. The sheet shall be fixed using self drilling/ self tapping SS screws of size 5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces i/c cutting to size and shape where required as per specifications, detail drawings and direction of Engineer -in- Charge. The rate shall be inclusive of all screws, seal, ridge, labour, scaffolding, machinery for fixing and approved sealent where required etc. but excluding the cost of purlins, rafters and trusses.

0.91 mm thick, the profile detail width 1044/920 mm, cover width 1000/875 mm.

Providing and fixing 0.71mm thick (weight not less than 2.18 Kg per sqm) colour coated Aluminium Modern Troughed sheets accessories, made of AA3003 ally conforming to IS 737-1974 in full hard (H18) tamper of HINDALCO Everlast or Equivalent as approved by Engineer-in-Charge and plyester top coat 15-18 microns using self drilling/self tapping.

Corrugated Ridges (900mm)

Barge board (Upto 300 mm).

Gutter .(600 mm over all girth).

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

12 mm cement plaster of mix :

1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix :

1:4 (1 cement: 4 coarse sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

Two or more coats on new work.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

On concrete work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Laying & Spreading WBM as per specification including compacting, spreading in uniform thickness, hand picking, rolling with 3 whelled road/vibratory roller 8-10 tonne in stages to proper grade and camber, applying and brooming requisite type of screening / binding meterial to fill up iterstics of coarse aggregate watering and compacting to the required density.

Sub-base with stone aggregate 90mm to 45mm including stone screening 13.20mm

Base-Course with stone aggregate 63mm to 45mm including stone screening 13.20 mm (Type - A)

Providing and applying tack coat using hot straight run bitumen of grade VG - 10 including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :

On W.B.M. @ 0.75 Kg / sqm.

On bituminous surface @ 0.50 Kg / sqm.

2.5 cm thick bitumastic sheet with hot bitumen of approved quality using stone chippings (60% with 12.5 mm nominal size and 40% with 10 mm nominal size) @ 1.65 cum per 100 sqm and coarse sand @ 1.65 cum per 100 sqm of road surface and with bitumen @ 56 kg/cum of stone chippings and @ 128kg/cum. of sand over a tack coat with hot straight run bitumen including consolidation with road roller of 8 to 10 tonne etc. complete. (tack coat to be paid separately) :

With paving Asphalt grade VG - 30.

Providing and laying bituminous macadam using crushed stone aggregate of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge.

50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 3.50% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Cement concrete flooring 1:2:4 (1 cement : 2 River sand : 4 graded stone aggregate 20 mm nominal size)finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

40mm thick with 20mm nominal size stone aggregate.

Providing and Fixing One pair of Basketball Pole (made of minimum 5.0 mm thick 8" Round Pipe), Acrylic Backboard with angle iron frame (180mm x 105mm x 25mm), Ring (20mm solid rod) and Net (regulation size) over existing foundation and foundation bolts.

Painting runway/taxi track/apron marking with adequate nos. of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge i/c cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete.

New work (Two or more coats)

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m) having 50 no rounds per 6 metre length, upto 3m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Preparation of sub-base for laying paver block with local suitable soil including , rolling with road roller curing etc. all complete.

Minimum thickness 15 cm

Supplying, stacking and Spreading 100 mm thick stone chips of 20mm nominal size, watering and rolling complete including preparation of the surface and rolling.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing flat back urinal of size 580x380x350mm with pressmatic urinal valve auto closing system with built in control lock and wall flange for urinal complete set alongwith instalation with control cock( of jagur code No.PRSO77 and equivalent) including fittings and cutting and making good the walls and floors wherever required : Hindware

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required:

White glazed fire clay kitchen sink of size 600x450x 250 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board

510x1040 mm bowl depth 250 mm.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Size 600x450x200 mm

Providing and fixing UPVC 110 mm grating for gully trap.

Providing and fixing kitchen sink including making all connections excluding cost of fittings.

White glazed fire clay sink of size 600x450x250 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Rectangular shape 1500x450 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder :

C.P. brass

Vitreous china

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour. Weighing not less than 300 gms.

Providing and fixing health faucet (15mm nominal bore) of approved quality.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: (make JAQUAR, PARRY WARE, KOHLER or equivalent brand)

15 mm nominal bore.

Providing and fixing PTMT grating of approved quality and colour.

Rectangular type with openable circular lid.

150 mm nominal size square 100 mm diameter of the inner hinged round grating.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti- microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threadedpolypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases andmaking good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work,including cutting chases and making good the wall etc.

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti- microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threadedpolypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge.Internal Exposed on walls.

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 40mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti -microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threadedpolypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge.External work

PN - 16 Pipe, 32 mm OD (SDR-7.4)

PN - 16 Pipe, 40 mm OD (SDR-7.4)

Providing and fixing PPR Unions

PPR Union 20 mm

PPR Union 25 mm

PPR Union 32 mm

PPR Union 40 mm

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore

Providing and fixing PPR gate valve of approved quality as per the direction of engineer in charge:

25 mm nominal bore

40 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

150 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing cement concrete surface drain including earthwork inexcavation 10cm thick base concrete and 23cm thick sidde waling with 1:3:6 finishing with plaster 1:4 including floating coat of neat cement including drain and its top and exposed surface including earthwork in excavation and disposal of surplus earth .etc.

23cm x 23cm surface drain

Constructing CC manhole in CC solid block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.5mm nominal size) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Inside size 90x80cm and 45cm deep including C.I. cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg)

P & F Stainless Swan neck steel pillar cock of approved quality & colour.

15 mm nominal bore.

Providing and fixing 3mm PVC rigid foam plain sheet celing of approved quality with necessary screws etc. fixed in aluminium section complete as per the direction of Engineer-in-charge (frame work to be paid separately) :

3 mm PVC Rigid foam plain sheet

Providing and fixing soil, waste and vent pipes : with UPVC pipe coforming to IS:13592 type B including jointing with seal ring conforming to IS:5382 living 10mm gap for thermal expansion

Single socketed pipe

110 mm dia.

75mm dia

Providing and fixing UPVC moulded self cleaning trap design with screw down or hinged grating with arm complete including cost cutting and making good the walls and floors Grating shall be stainless steel of 100mm dia

100 mm inlet and 75 mm outlet

Providing and fixing UPVC moulded door bend of required degree for UPVC soil pipes conforming to IS:13592 type "B" including jointing with seal ring conforming to IS:5382 living 10mm gap for thermal expansion

75 mm dia

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete

100x100x100x100mm

75x75x75x75 mm

Providing and fixing UPVC moulded heel rest sanitary bend of required degree for UPVC soil pipes coforming to IS:13592 type B including jointing with seal ring conforming to IS:5382 living 10mm gap for thermal expansion

100 mm dia

Providing and fixing UPVC moulded plain bend of required degree for UPVC soil pipes conforming to IS:13592 type "B" including jointing with seal ring conforming to IS:5382 living 10mm gap for thermal expansion

P & F UPVC moulded terminal guard:

P & F UPVC moulded collar.

P & F counter tops wash basin (colored) of Sheraton series of pattern code-329 of Neycer, Parryware or equivalent make including, fitting, cutting and making good the walls wherever required.

White vitreous China under counter basin size 590x420x195mm (Jaguar, Hindware, Roca, Parryware, Kohler and equivalent.

Providing and fixing CP Soap Dish Holderas approved by Engineer - in - charge with concealed fitting arrangements

P & F PVC moulded corner tile beading of required shape and colour to the junction of walls etc. with cement mortar etc. complete as per direction of Engineer-in-charge. .

Providing and laying water proofing treatment at terrace with Dr. Fixit Flexi PU270(I) or equivalent

Supply and applying single component, root resistant, elastomeric pure polyurethane membrane free from bitumen and tar, Dr.Fixit Flexi PU 270(I) or equivalent with minimum elongation of 400% and solid content 90%. The system consist of aaplying the waterproofing treatment @ 1.35KG/Sqm to achieve a DFT of 1.2mm..

Providing and laying of protective geotextile fabric 150GSM over the entire membrane with proper overlaps.

Supplying and applying UV resistant TOP coat.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 2500mm length), fixed one end with roof truss members and another end with aluminium cealing members, complete as per direction of Engineer -in-charge.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Powder coated minimum thickness 50 micron aluminium tubular handle bar.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Providing and fixing bright finished stainless steel hanging type floor door stopper with necessary screws etc. complete :(make with IPSA brand or equivalent)

Providing and fixing stainless steel polished chrome Center Patch Lock with Cylinder and strike plate suitable for glass thickness 10 mm / 12 mm etc.(of Dorset, Dorma, Ingersoland, GEZE or equivalent brand)

Providing and fixing Stainless steel tubular handle bar 32mm dia and 600mm long H type (Code No. SH 24 PSS of DORSET or Equivalent company) SS 304 grade of make DORSET or equivalent brand with SS screw etc. complete as per the direction of Engineer-in- incharge.

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead up to 50 m and lift up to 1.5 m :

All kinds of soil

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry Hallow block honey comb shaft with C.C hallow block of size 400X100X200 mm filled with agreegate 90mm - 45 mm size and UPVC drain pipe 110 mm diameter, 1.8 m long complete as per standard design.

With 400X100X200 mm hollow block

Providing and construction gabion structures for erosion control and protection work with polymer wire crates of size each divided into 01 mtr compartments by cross netting with mesh opening size 150mm x 150mm , made from 09mm polymer rope (PP) having weight of 40 gm per mtr with a tolerance of + or - 8% 1560 kg breaking strength (mm) and after 1000 cycles of abrasin the rope shall be filled with boulder with least dimension of 200mm , all loose ends to be securely tied with 9mm polymer wire as per specification of standard specifications of gabion and as per the direction of EIC.

With polymer wire crest of size 3.00 m x 1.00m x 1.00m

With polymer wire crest of size 2.00 m x 1.00m x 1.00m

With polymer wire crest of size 1.00 m x 1.00m x 1.00m

Supplying and filling stone boulder of size 22.5 mm and above for filter media 1.20 sqm area behind complete

ELECTRICALWORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group - A

Group - B

Group - C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmouredtelephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

3 Module (100mmX75mm)

4 Module (125mmX75mm)

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supplying of Industrial Box type luminaire suitable for twin T8 LED Tube, Cat No. IGP132LT8-16 with 2 Nos. 20W each LED T8 Tubular lamp Cat No. LT8-20-865-2 Make: Crompton/Havells/Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Batten suitable for LED T8, Cat No. DMLN1LT8-16 with 20W LED T8 Tubular lamp Cat No. LTT8-20 Make: Crompton/Havells /Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Square Surface mounted LED fitting 36W Cat No. LCTLSN-36-CDL, Make: Crompton/Havells/ Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Lamps LED ADORE 9W 865 B22 4 STAR LAMP, Cat No. LHLDEUECNL8R009 Make: Havells/ Crompton / Philips/Bajaj or equivalent with NABL certified as required.

Supplying of LED Adore Lamp 0.5 W B22 Blue, Cat No. LHLDAFUEUSNX0X5 Make: Havells/ Crompton / Philips/Bajaj or equivalent with NABL certified as required.

Supplying of LED Bulk Head fitting 10W Cat No. LBHP-10-CDL Make: Crompton/ Havells/Philips/Bajaj or equivalent with NABL certified as required.

Supplying of LED Mirror light fitting 07W Cat No. LCL-07-CDL, Make: Crompton /havells/Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Round Surface mounted LED fitting 18W Cat No. LCDSPLN-R-18-CDL, Make: Crompton/Havells /Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Round Recessed mounted LED fitting 18W Cat No. LCDE-18-CDL, Make: Crompton/ Havells/Philips /Bajaj or equivalent with NABL certified as required.

Supplying of Square Surface mounted LED fitting 18W Cat No. LCDSPLN-S-18-CDL, Make: Crompton/Havells/ Philips/Bajaj or equivalent with NABL certified as required.

Supplying and fixing of LED Post Top lantern, IP65 20W Cat No. LPTH-20-WW, Make: Crompton/Havells/ Philips/Bajaj or equivalent with NABL certified as required.

Supplying of Circular LED Flood with innovative finless design and excellent thermal management and light distribution along with IP66 protection 35W Cat No. LFLN11-35-CDL/60, Make: Crompton/Havells/Philips/Bajaj or equivalent with NABL certified as required.

Supplying of A.C ceiling fan (1400mm sweep) i/c down rod of standard length 30 cm with all accessories etc as required. Make: Havells/Usha/ Bajaj/ Orient/ Crompton or equivalent to ISI standard.

Supplying of A.C ceiling fan (1200mm sweep) i/c down rod of standard length 30 cm with all accessories etc as required. Make: Havells/Usha/ Bajaj/ Orient/ Crompton or equivalent to ISI standard.

Supplying of exhaust fan of size 300mm sweep with all accessories etc as required. Make; Usha/ Bajaj/ Orient/ Crompton/Havells/Kaithan or equivalent to ISI standard.

Supplying of PVC insulated and PVC sheathed/ XLPE LT Power Cables, aluminium conductor UG cable of 1.1 KV grade of following size below, as per relevant IS code. Make: Havells and should be NABL certified or equivalent to Polycab/Finolex etc. as required.

2C 6 Sq.mm

3.5C 400 sq. mm

3.5C 150 sq. mm

Supplying, Installation testing and commissioning of Instant Geyser of 3 Ltr. Capacity, White Blue, 3 KW, Cat No. GHWEIAPWB003 Make-Bajaj/ Orient/ Crompton/Havells or equivalent to ISI standard.

Supplying & Laying of double walled corrugated high density polyethylene pipe having corrugation at the outer wall and plain surface inner walls, conforming to IS 14930 part-II & E/in/C(MES), complete with necessary HDPE fittings for protection of 1.1 KV underground cable directly in ground at a depth of 50 cm including excavation and filling the trench etc as required.

200 mm outer dia and 174 inner dia nominal size

145 mm outer dia and 126 inner dia nominal size

50 mm outer dia & 38 inner dia nominal size

Supplying of Circular LED Flood with innovative finless design and excellent thermal management and light distribution along with IP66 protection 200W Cat No. LSFO-200-CDL/60, Make: Crompton/Havells/Philips/Bajaj or equivalent with NABL certified as required.

Supply, installation, testing, commissioning & Erection of outdoor feeder pillar type 500A, MCCB as per MSEDCL Approved, 415 volts 50Hz 3 phase non-extendable type, one side open i/c front single hang shutter with locking arrangement and top cover made out of 3.25mm thick CR sheet of size 1000 cmx 900mx1500cm M.S. Angle, M.S. Flat to accommodate. The panel should have provision for inner earthing, 1 coat of primer and 2 coats of finishing water proof paint etc as required.

Supply, installation, testing, commissioning & Erection of outdoor feeder pillar type of 1000A, ACB, as per MSEDCL Approved, 415 volts 50Hz 3 phase non-extendable type, one side open i/c front single hang shutter with locking arrangement and top cover made out of 3.25mm thick CR sheet of size 1000 cmx 900mx1500cm M.S. Angle, M.S. Flat to accommodate. The panel should have provision for inner earthing, 1 coat of primer and 2 coats of finishing water proof paint etc as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc.as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way , Double door

12 way , Double door

16 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & witch box excluding modular plate as required.

Supplying, Installation, testing and commissioning of ASHLOK make SEE brand safe earthing electrode type-19, 50mm dia,length 2 mtrs and inner space to be filled with crystaline conductive mixture including filling up with electrodite (Back fill compound) as required for safe earth electrode and providing masonary enclosure with cover plate having locking arrangement etc. as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supply, installation, Testing & commissioning of "KOHLER" Make, KDG0500P1 Model, 1500 RPM, Six Cylinder, Vertical, liquid - Cooled Diesel Oil Engine Directly Coupled ' B17 AC Alternator, 3 Phase, 415 Volts, 50 Hz @0.8 P.F self excited, Self regulated Designed to Run at 1500 RPM 400 KW/500 KVA DG set with AMF panel

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Fabricating and Supplying of Street Light Pole 5.0 mtr long from ground made out of medium Class GI pipe of size 65mm dia & 02 Nos 32 mm dia 2 mtr long G.I.Pipe medium class for mounting of 72 watt LED Street Light fitting welded at the pole top including bending the pipe to required shape and 300mm x 6 mm MS base plate welded to the bottom making holes & Sintex box of size 170 x 170 x 105(mm) with 01 No. 6 amps MCB & Nut & Bolt for fastening the base i/c painting with one coat of metalic primer & two coats of metalic white paint as reqd.

Erection of metallic pole of following length in cement concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 4.5 meter and upto 6.5 meter

Supplying and fixing of power Contactor 40Amps current rating in the existing feeder box similar to Indo Asian Cat Ref. No.C106004 or its equivalent as required.

Supplying & Fixing of 60 watt LED Street light fitting Crompton Cat No-LSTP-60-CDL Make: Crompton/Havells/Philips/Bajaj or equivalent, with NABL certified as required.

Supplying and fixing of analog time switches (with battery backup) of 3 P Module, 24 hours program, Programmable every 30 min, backup of 100Hrs, current capacity 16A, with 1 changeover (1CO) in the existing feeder box, Indo Asian Cat Ref.No.TA926453 or its equivalent as required.

Supplying, installation, testing and commissioning of Feeder box of suitable size 800 mm X 600mm X 350mm should be dust and vermine proof made out of 2mm thick CRCA sheet with front opening, double leaf hinged door with locking arrangement i/c connection with 3 nos Porcelein rewireable fuse unit of 200 amps & neutral link with bus bar of size 30mm x 5mm x 350mm made of copper strips and duly painted with 1 coat steel primer, 2 coat of finishing water proof paint etc as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

2 X 10 sq. mm (19mm)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required

Upto 35 sq. mm

‘A’ Frame Panel Boards, O/G TP MCCBs Double Door, 800A CN/CH frame MCCB, 6 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVA08000600 / L&T or equivalent. -1No.

Cable Alley I/C 400A/630A/800A, O/G 4P GF 8Way & TP A/F 8Way for G/A frame Panel board outgoing TP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0701 / L&T or equivalent.-1 No.

Incoming MCCB 400A 4Pole breaking capacity 35 KA Frame CN, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No.IHLCNF0400 # / L&T or equivalent.-1No.

Outgoing MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-3Nos.

Add on Incoming Changeover Switch Enclosure, 800A Incoming change Over switch-F3 Make: Havells Cat No. ISSBOU0710 / L&T or equivalent.-1No.

On-Load Changeover Switch I-O-II, 800A frame size 1, Make: Havells Cat No. IHCNFO0800 / L&T or equivalent.-1No.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 400A CN frame MCCB, 6 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF4000600/ L&T or equivalent.-1No.

Cable Alley I/C 400A/630A/800A, O/G 3P GF 8Way, 4P 6Way & A/F 6Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0699 / L&T or equivalent.-1No.

Incoming MCCB 400A 4Pole breaking capacity 35 KA Frame CN, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0400 # / L&T or equivalent.-1No.

Outgoing MCCB 100A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0100 # # / L&T or equivalent.-3Nos.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-3Nos.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 250A AA frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF2500400/ L&T or equivalent.-No.

Cable Alley I/C 250A,O/G 3P GF 6WAY & 4P 2/4Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0691 / L&T or equivalent.-1No.

Incoming MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-1No.

Outgoing MCCB 100A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0100 # # / L&T or equivalent.-3Nos.

Outgoing MCCB 63A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0063 # / L&T or equivalent.-3Nos.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 250A AA frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF2500400/ L&T or equivalent.-1No.

Cable Alley I/C 250A,O/G 3P GF 6WAY & 4P 2/4Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0691 / L&T or equivalent.-1No.

Incoming MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-1No.

Outgoing MCCB 200A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0200 # # / L&T or equivalent.-1No.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-2Nos.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 250A AA frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF2500400/ L&T or equivalent. -1No.

Cable Alley I/C 250A,O/G 3P GF 6WAY & 4P 2/4Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0691 / L&T or equivalent. -1No.

Incoming MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent. -1No.

Outgoing MCCB 125A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0125# # / L&T or equivalent. -1No.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-3Nos.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘A’ Frame Panel Boards, O/G TP MCCBs Double Door, 800A CN/CH frame MCCB, 6 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVA08000600 / L&T or equivalent.-1No.

Cable Alley I/C 400A/630A/800A, O/G 4P GF 8Way & TP A/F 8Way for G/A frame Panel board outgoing TP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0701 / L&T or equivalent.-1No.

Incoming MCCB 800A 4Pole breaking capacity 35 KA Frame CN, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No.IHLCNF0800 # / L&T or equivalent.-1No.

Incoming MCCB 400A 4Pole breaking capacity 35 KA Frame CN, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No.IHLCNF0400 # / L&T or equivalent.-1No.

Outgoing MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-2Nos.

Add on Incoming Changeover Switch Enclosure, 800A Incoming change Over switch-F3 Make: Havells Cat No. ISSBOU0710 / L&T or equivalent.-1No.

On-Load Changeover Switch I-O-II, 800A frame size 1, Make: Havells Cat No. IHCNFO0800 / L&T or equivalent.-1No.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 400A CN frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF4000400/ L&T or equivalent.-1No.

Cable Alley I/C 400A/630A/800A, O/G 3P GF 8Way, 4P 6Way & A/F 6Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0699 / L&T or equivalent.-1No.

Incoming MCCB 400A 4Pole breaking capacity 35 KA Frame CN, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0400 # / L&T or equivalent.-1No.

Outgoing MCCB 160A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No.IHLFNF0160 #/ L&T or equivalent.-3Nos.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-1No.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 250A AA frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF2500400/ L&T or equivalent.-1No.

Cable Alley I/C 250A,O/G 3P GF 6WAY & 4P 2/4Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0691 / L&T or equivalent.-1No.

Incoming MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-1No.

Outgoing MCCB 63A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0063 # / L&T or equivalent.-2Nos.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-2Nos.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

‘G’ Frame Panel Boards, O/G FP MCCBs Double Door, 250A AA frame MCCB, 4 way outgoing, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. IHVGF2500400/ L&T or equivalent.-1No.

Cable Alley I/C 250A,O/G 3P GF 6WAY & 4P 2/4Way for G/A frame Panel board outgoing FP MCCB incomer A & C frame mccb Double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No.ISSBOU0691 / L&T or equivalent.-1No.

Incoming MCCB 250A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLCNF0250 # / L&T or equivalent.-1No.

Outgoing MCCB 200A 4Pole breaking capacity 35KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0200 # # / L&T or equivalent.-1No.

Outgoing MCCB 40A 4Pole breaking capacity 25KA Frame AS, Conforms to IEC:60947-II / IS:13947-II, Make: Havells Cat No. IHLFNF0040 # / L&T or equivalent.-1No.

Installation accessories such as lugs / comparsion gland / Rubber Foot Mat-1 Job

M/s AGGARWAL CONSTRUCTION COMPANY

O P KANDOI AND COMPANY PVT LTD