PROVN OF 4 X GUARD ROOM AT ENTRANCE FO SAINIK CHOWK GATE ENTRY EXIT GATE AT CIRCULAR ROAD MD ACCN COMPLEX ENTRY EXIT GATE AT ALBERTIKA MARG AND ENTRY EXIT GATE ANAND BAZAR DEVANIA NALA BRIDGE INCL 01 X TOILET IN GUARD ROOM AT SAINIK CHOWK AND RENOVAT

Amount

Boring holes 3m deep in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50m (dia of pile 300mm)complete all as specified and directed

Excavation in trenches in soft/ loose soil not exc 1.5m wide and not exc 1.5m deep for foundation, pier holes etc n. exc 10sqm on plan and getting out complete.

Surface Dressing n.exc (not exceeding) 15 cm deep in Soft /loose Soil complete all as specified and directed

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling, sub base and mass concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete all as specified and directed

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in columns, pillars, posts, struts etc complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in Chajjas and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specifed and directed.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete.

M&L mild steel TMT bars 6 to 8 mm cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete.

M&L hard core of broken bricks of gauge n exc 63mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate), as in sub base finished even & fair etc complete all as specified and directed.

M&L for glazed ceramics coloured tiles of size 450x300x7mm thick as in vertical surfaces such as skirting/dados/wall, etc with and including over 10mm thick rendering in cmeent mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces.

M&L for Non -Skid Ceramic coloured tiles (joint free) 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm , in floors etc over and including15mm thick screed bed in cement mortar 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

Returning, Filling in including Spreading, Leveling, Watering and Well Ramming in layers not exc. 25 Cm thick in Soils, complete all as specified and as directed.

Removing excavated soil to a distance not exc 50.00 Metre away and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and as directed.

S&F Pressed steel frame for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc of size 125X60 mm made out of 1.25mm thick MS sheet , complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-0 (using 12.50 mm graded stone aggregate), as in back filling of pressed steel frames and similar workd including necessary form work as required complete all as specified and directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats etc complete all as specified and directed.

S & F steel window with side hung shutters including projecting or box type hinges with steel handle peg stay complete with glazing bars, dovetailed or welded.

S & F steel window with side hung shutters including projecting or box stype hinges with steel handle peg stay complete without glazing bars, dovetailed or welded.

S & F Steel ventilator with top hung shutter including, hinges, peg stay, complete all as spesified and directed

S&F 100 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F for extruded brass handles, fabricated type, polished 150 mm size complete all as specified and directed.

S & F of 200 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 150 mm long brass barrel tower bolt with cast or sheet barrel and rolled or cast bolt section acomplete all as specified and directed.

S&F floor door stopper 140 mm overall length of cover plate of aluminium alloy body and tongue, anodised. With hard drawn spring, fixed in floor. complete as directed by Engr-in-charge

S&F GI wire cloth 0.56 mm nominal dia of wire andbrick average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S&F 3 mm thick sheet glass, ordinary quality, and glazing with oil putty in square/rectangle n exc 0.50 sqm in each pane, complete all as specified and directed

S&F in repair 18/19 mm thick Block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, including teak wood lipping, 6 mm thick on sides complete for cupboard shutter and incl shelves all as specified and directed

S&F 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete.

S&F in repair mild steel conduit curtain rod with PVC coating fancy type curtain rod 25 mm dia of any colour as approved complete.

S&F mild steel Bracket with PVC coating fancy type for curten rod 25 mm dia of any colour as approved complete.

Supply only water proofing compound (liquid),ISI marked.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in CM (1:6), finished even and smooth (Without using extra cement ) complete all as specifed and directed.

M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specifed and directed.

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of primer including 3 mm thick Birla/ JK wall putty complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat primer complete all as specified and directed.

M&L for applying two coats of oil bound distemper on plaster surface of ceiling over a coat of primer including, rubbing with sand paper complete all as specified and directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Note for item No 49 to 59 (i) CPVC fittings with brass threading will be measured and paid separately under items No (ii) Cost of normal plain SDR CPVC fittings Like Bend, Tee, Elbow, Union etc shall inclusive under the quoted rate of pipe including.

S&F of CPVC 20 mm Outer dia Brass Elbow complete.

S&F of CPVC 20 mm Outer dia Brass Elbow (3/4 x 1/2) complete.

S&F of CPVC 20 mm Outer dia Brass Tee complete.

S&F of CPVC 20 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 25 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 20 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 25 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 20 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 25 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 20 mm Outer dia Brass Union complete.

S&F of CPVC 25 mm Outer dia Brass Union complete.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer hoisted and fixed in position all as specified in SSR Pt-I of 500 Ltr capacity complete all as specified and directed.

S&F nipple suitable for HDPE water tank (min weight 15mm-38gms)

S&F Gun metal, globe or gate valve with iron wheel head, 15 mm bore, screwed both ends for iron pipe complete all as specified and directed.

S & F for Wash Hand basins, Vitreous China, white, flat back, size 550x440mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing of supply, waste pipe, taps) complete all as specified and directed.

S&F white vitreous china wash down water closet pan pedestal pattern (white) fixing bolts, and flush pipe excluding flushing cistern complete all as specified and as directed.

S&F for vitreous china squatting pan, Orissa pattern of size 580 mm x 440 mm white, with integral foot rest, 'P' or 'S' trap including connection to trap, and to flush pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and directed.

S&F PVC valve less, syphonic action type flushing cistern of 10 liter capacity, low level with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F PVC (SWR) nahani/ floor trap, plain with grating with solvent cement 75mm dia etc complete

S&F bib tap 15mm cast copper alloy chromium plated long body with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

S & F for 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repairs PVC connection 15mm dia size and 450 mm long with 2 Nos brass check nuts its washers complete all as specified and as directed. Make- Prayag/Parryware/Hindware

S&F in repair brass CP tubular towel rail 20 mm dia "D" type 60 cm long complete all as specified and directed.

S&F angle cock 15mm cast copper alloychromium plated screw down screwed for iron pipe of brass ferrule etc complete all as specified and directed.

S&F plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC complete all as specified and as directed.

S&F PVC (SWR) 'P' trap for 110 mm dia etc complete.

M&L for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded stone aggregate) including necessary form work complete.

M&L for 20 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete.

S & F for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F for 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for PVC (SWR) vent cowl of 110 mm dia complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finishing even & smooth without using extra cement laid in bays with construction joint filling with mastic asphaltic concrete complete all as specifed and directed.

M&L for 150 mm dia reinforced concrete pipes, class NP 2 with one collar per length of pipe complete all as specified.

M&L for concrete bed to drain pipes of 150mm dia including packing under, and haunching against the sides of pipes after they are laid and tested;in PCC 1:3:6 type C2 using 40 mm graded stone aggregate concrete all as spd.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specifed and directed.

S & F 28 to 30 mm(stiles) Factory Made Solid PVC Moulded door shutter with particle board core , with 2, 3 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, in frame at site as per specification & drawings as given in SSR part - II (2020 print) on serial page No. 181 complete all as specified and directed.

S&F Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete all as specified and directed.

S & F Vitreous China Half stall type urinals, white, incl spreader (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed.

Construction of Septic tank for 10 users as shown on Drawing No.CE/TD/2022 /16 dated 1610.211 complete all as specified and directed.

Construction of Soakage wells 1.2 m dia and 3.0 m effective depth complete as shown on Drawing No.CEJZ/TD/58 sheet 1/1dated 05.05.2000

M & L for plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates as in foundation for manholes and drains complete all as specified and directed

M & L for plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate), as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for plain Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching and surface channel of Manholes complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thicknesses, below or above ground level, complete all as specified.

Dismantling of floor, walls tiles incl bedding but backing and rubbish off permises all as specified.

M & L for Non skid ceramic coloured tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exc. 0.38sqm as in floor etc. with and including over 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exc. 0.38sqm, in vertical surface such as skirtings, dados etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile, including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in floors including finishing the surface rough & even for receiving kota stone/tiles complete.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified.

M&L 50 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key and scrubbing down with water etc all as specified and directed.

Taking down chowkats or frames with shutters of any description (without taking off shutters from frames) area not exceeding 1.50 sqm each, all as specified and directed.

~Ditto~ all as per Srl item No. 106.00 above but exc 1.5 sqm but not exc 4 sqm each.

Taking down shutter of any description exc 1 sqm and n.exc. 2 sqm each and removing to store complete all as specified and directed.

S & F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165 complete all as specified and directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F mild steel, 150mm long ordinary helical door spring incl roller and roller plate complete

M&L for 150 mm long aluminium anodised barrel tower bolts extruded section and fixed complete all as specifed and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F in repair GI wire cloth 0.56 mm nominal dia of wire andbrick average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S & F for 3 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing of 15 mm dia.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store of 20 mm dia.

S & F 15mm bore tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors or trench etc complete all as specified and directed.

S & F 20mm bore tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors or trench etc complete all as specified and directed.

S&F 15 mm bore concealed type stop cocks, cast copper alloy, chromium plated with long shank and cup (concealed type), high pressure with capstan head handle, screwed both ends for iron pipe or for unions of 15 mm dia.

S&F in replacement of stainless steel soap dish, of standard size and shape complete all as specified & directed.

S&F in repair brass chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

Taking down PVC/AC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100 mm dia pipe.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS brackets etc of 110mm dia. complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F PVC (SWR) pipes 50mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

M&L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 75 mm dia

S&F PVC (SWR) multi floor trap, plain with grating or without waste hole with solvent cement 75mm dia etc complete

Dismantling water tanks and removing to store of capacity 250 and n exc 500 ltrs complete all as specified and directed.

S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball srewed for iron pipe and fixed (minium weight 20mm-210)gms. complete all as specifed and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M&L for applying 2 mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

M&L for preparation of newly plastered surface of wall & concrete and applying 2 mm thick wall care putty including preparation complete.

M&L for applying two coats of oil bound distemper on plaster surface of wall & concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M&L for applying 1mm thick Birla / JK Putty in two layers on old ceiling surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling & applying 1 mm thick wall care putty including preparation of new surface complete.

M&L for applying two coats of oil bound distemper on plaster surface of ceiling over a coat of primer including, rubbing with sand paper complete all as specified and directed.

M&L for Preparation of old painted surfaces of wall, chajjas etc by washing rubbing down and stopping and applying two coat of cement base paint white or tinted complete all as specified and directed.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete.

S&F in repair vitreous china squating pan 'Orissa' pattern WC size 580x440 mm white with integral foot rest and trap and including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor all as spd.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

M&L for two coats of weather coat paint (apex) over a coat of primer on new surfaces on wall including preparation of newly/Old plastered surfaces complete all as specified and as directed by Engr-in-Charge.

Taking down carefully copper / aluminium point wiring (light, fan, switch, socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose, sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's with MCB and making good the disturbed surfaces of walls complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls complete all as specified and directed.

M & L for Point wiring with PVC insulated PVC unsheathed electric FRLS cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling PVC conduit on surface will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including MS boxes 1.6 mm thick and 3 mm thick plastic laminated sheet for mounting switches, sockets, fan regulators etc for one light/fan point controlled by one switch complete all as specified and as directed.

All as per item no 155.00 above one 5 Amps socket out let point controlled by one switch on same board with other switches complete all as specified and directed.

All as per item No 155.00 above one 5 Amps socket out let point on independent board controlled by one switch complete all as specified and directed.

All as per item No 155.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent boardcomplete all as specified and directed.

Supply and fixing switch piano flush button single pole one way 5 amps, 240 Volts complete all as specified and as directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, 240 Volts complete all as specified and as directed.

Supply and fixing switch piano flush button single pole one way 15 amps, 240 Volts complete all as specified and as directed.

Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 240 volts complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 63.5mm dia three terminal, fixied complete all as specified and as directed.

Supply and fixing for batten / angular fittings complete all as specified and as directed.

Supply & fixing for electronic Fan regulator 450 watt step type complete all as specified and directed.

S&F LED lamp 7/8 watt complete all as specified and directed.

Supply and fixing double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed . Make: L&T/LEGRAND/SCHNEIDER/HAVELLS/HPL

Supply and fixing MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make: Schneider/ Legrand/ L&T / ABB.

Supply and fixing MCB SP 240 volts 5 to 40 Amps, 10 KA breaking capacity, 'C' type including connection complete all as specified and directed by Engr-In-Charge. Make : Legrand/Schneider/Siemens.

Supply and fixing in repair LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder including one nos LED tube rod 18/20 watt and all accessories internally pre wired and fixed to wall/ceiling incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. Make- Bajaj/Surya/ Havells / Crompton Greaves/ Bentac/Eveready .

S&F for LED batten tube light fitting 1x 9 watt 230 volt wall/ ceiling mounted luminaire with polycarbonate housing and integrated electronic driver with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. Make- LUMILINEBS9WLED840SPCCWH or equivalent of Bajaj/Philips/CG/Bentac/Eveready.

Supply and fixing metal body air fan / ventilator with louver 450 mm sweep and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper conductor and sheathed cable upto ceiling rose complete all as specified and directed .Make: HAVELLS Cat No-Ventil Air - DS

M&L for Sub main wiring two single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including PVC insulated unsheathed 2.5 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete.

S&F for LED light fitting 1x9W/1x10W bulkhead ;uminaires incl LED light driver holder connceting up with three flexible copper conductor cable of suitable size complete all as specified and directed. Make- Bajaj/Surya/ Havells / Crompton Greaves

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper wire upto ceiling rose complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Usha.

Supply, fixing and testing of ceiling fan 1200mm sweep, heavy duty, single phase, AC, 230 Volts, 50Hz, BEE 5 star rating, ISI marked complete with down rod, canopy, blades, BLDC motor without remote, electronics fan regulator etc and connecting up complete including complete connection from ceiling rose to fan including writing of MES Number with synthetic enamel paint complete all as specified and as directed. Make:- Bajaj/Usha/Crompton Greaves/Havells/BLDC

S&F for LEDstreet light (for building) fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrison resistant incl thermal managment in multiple optics complete with IP 65/66 protection complete all as specified and directed. Make- Bajaj/Surya/ Havells / Crompton Greaves

Supply and fixing in repair of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 15 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete.

Supply , laying & testing XLPE insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 10 Sqmm nominal cross section x 2.0 core. Make- Havells/Ploycab/KEI /Gloster.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core. Make: Havell's/Polycab/ KEI/MESCAB

Taking out of pressed precast concrete interlocking paver block any shape and size and refixing of same with 50mm thick sand cushioning filling under floors or in foundation including watering and consolidation complete all as spd and directed by EIC

M & L dry sand cushioning to underground cables with 8 cm thick before laying the cable and 15 cm in thick after layingand stretching of cable and gently hand ramming and consolidation of thickness of sand 18cm all as specified and directed by EIC. Note:- sand thickness shall be measured 18cm only.

M & L for old size sub class ‘B’ bricks, laid in trenches as cable covers / protection complete all as specified and directed .

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

Supply, fixing & laying only GI tubing medium grade with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings ISI marked for laid in trenches/wall/ceiling/ floor/ all as specified and directed of following size:-

25 mm bore

S&F Stop Valve brass spindle, screwed, 15mm with iron wheel head, screwed both ends for iron pipe for following size:-

25 mm bore

20 mm bore

M&L for tapping/cutting from DI/GI pipe any diameter including suitable size Tee/fittings for 25mm dia GI pipe complete all as specified and as directed.

M/s Naresh Chand Agrawal

M/S Priya Trading Agency

M/S PRAVIN ENTERPRISES

M/S SAROJ KUMAR SINGH

RAJ AND SONS

jaglalchoudharyandsons

SINHA CONSTRUCTION