Construction of control room building for receiving station at 132/33kV Grid Station Nowbugh Chadoora.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:1 meter from cutting edge All kinds of soils

Providing & laying in position cement conc. of specified grade excld. Cost of centering & shuttering- all work upto plinth level in 1:4:8 (1 cement :4 coarse sand :8 graded stone agg. 40 mm nominal size (Crushed)

Providing and laying in position specified grade of reinforced cement conc. excluding the cost of centering, shuttering, finishing -and reinforcement All work upto plinth level, M20 grade concrete

Providing and laying in position specified grade of reinforced cement conc. excluding the cost of centering, shuttering, finishing -and reinforcement All work upto plinth level, M20 grade concrete Plinth beam with reinforcement @1 Qtl/Cum

Providing & laying in position cement conc. of specified grade excld. Cost of centering & shuttering- all work upto plinth level in 1:2:4 (1 cement :2 coarse sand :4 graded stone agg. 40 mm nominal size (Crushed) M-15 Grade PCC

Providing , laying , compacting & ramming of stone boulders of size for back filling of the excavated soil upto plinth level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Flooring with cement concrete 1:2:4 mix incl. floating coat of neat cement 50 mm thick

Brick work with F.P.S. bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). Upto 1st floor

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Centering & shuttering incld. strutting, propping etc. & removal of form

Centering & shuttering incld. strutting, propping etc. & removal of form for:-

12 mm thick cement on the rough side of single or half brick wall of mix:1:6 (1: cement :6 fine sand)

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, including panelling of 25mm thick Ist Class Kail wood and Glass Pans 4mm thick, all complete as per direction of Engineer-in-charge 35 mm thick. First Class kail wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.First class kail wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge 35mm Thick First class kail wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Supply & Fixing of 600 mm in width coloured PGI sheets 0f 0.63 mm thick incl. cost of all materials required for the job

supply & Fixing of 300 mm in width Eavea Boarding of 0.50 mm thick coloured GI Sheets incl. cost of J or L hooks or 8mm nuts & bolts

Providing & Fixing of electric wiring (Copper) incliding main service line (25mm cable) of standard gauge in concealed HDPE conduits and fittings/heating/lighting points (1.5mm² )of standard make like Polycab/Philips/Havels/Bajaj/Legrand/ Anchorwith 30 No lighting points (15/16Amp 2.5mm² ) including LED Lamps of Make Syska, Anchore, Philpes and 15 No heating points(15/16Amp 4mm² ), three No Fan points including cealing fans capastor type with 3 blades, copper winding with regulator and 3 No. Exuas Fans of standard make like Usha,Havels MCBs 6amp, 16 Amp 32 Amp and Change over switch, Main Board and sub switch board etc. as per directions of Engineer-In-Charge with cost of all materials (Complete job in all respects)

Applying priming coat with ready mix primer of standard brand & manufacture on wood & wood based surfaces as per directions of Engineer-In-Charge with cost of all materials

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work as per directions of Engineer-In-Charge

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Finishing walls with water proofing cement paint (Excel) of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Suppying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 em long wire springs manufacture from high tensile steel wire of adequate strength confirming to IS 4454 part1 and M.S. top cover of required thickness for rolling shutters 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing water heater reputed make (venus, racold, etc) ISI mark including all necessary fittings including making good wall after installation all complete 50 litre capacity

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm

Providing and fixing of ceramic glazed floor tiles 300x300 mm /600x600 mm 12mm thickness to be specified by the manufactures of ist quality conforming to IS:13755 of approved make like ,orient,somany,kajaria or equivalent make in all colour such as white, ivory, grey, fume red, brown laid on 20 mm thick bed of cement mortar 1:4 1 cement:4 coarse sand including pointing the joints with white cement and matching pigment etc.complete

Providing and fixing wash basin with C.I/M.S brackets 15mm C.P brass pillar taps 32mm C.P brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls where ever required. White Vitreous China Wash Basin size 630mmx450mm with a pair of C.P brass pillar taps

Providing and fixing Polyethylene- Aluminum- Polyethylene (PE-ALPE) Composite Pressure Pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80ºC, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. Elbows, tees, reducers, couplers and connectors etc. This includes testing of joints complete as per direction of the Engineer-in-charge:Internal work concealed with clamps at 1.00 meter spacing including cutting the chases and making good the wall etc. 19.1.2.1 1216 (16mm OD) pipe

Providing and fixing water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S trap, 10 liter low level PVC flushing cistern including flush pipe ( of approved make) manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Long pan pattern white vitreous china WC pan of size 580mm

Providing and fixing Polyethylene- Aluminum- Polyethylene (PE-ALPE) Composite Pressure Pipes conforming to IS: 15450, U.V. stabilizedwith carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80ºC, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. Elbows, tees, reducers, couplers and connectors etc. This includes testing of joints complete as per direction of the Engineer-in-charge External work including trenching and refilling etc. complete (20mm OD) pipe

Construction of brick masonry manhole in cement mortar 1:4(1 cement : 4coarse sand) RCC top slab with 1:2:4 foundation concrete 1:4:8 inside plastering 12mm thick in cement mortar 1:3 Mix Size of manhole 90x80x 45 cm inside

Providing and fixing PVC waste pipes for bath & kitchen including PVC waste fittings complete upto disposal system

Providing and fixing C.P bib cock (Parco Or Jaqvar) of approved quality 15mm nominal bore

Providing fixing C.P Stop cock/Angle valves (Parco Or Jaqvar) concealed of standard design and approved make conforming to IS 8931 15mm nominal bore

Providing & Fixing of CP Brass Wall Mixer of (Parco Or Jaqvar) 15 mm nominal bore

Providing & Fixing of CP Brass wash basin Mixer and sink mixer of (Parco Or Jaqvar) 15 mm nominal bore

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P brass screws with concealed fiting arrangement of approved quality and colour. 450 mm long towel rail with total length of 495mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms

Dry random rubble masonry with hard stone in foundation and plinth

Providing and fixing salem stainless steel sink A ISI 304(18/8) KITCHEN SINK as per IS 13983 with CP Brackets amd stainless plug 40mm including painting of all necssary accsories and making good the wall whatever required.510x1040mm bowl depth 225mm

Providing & Fixing Stainless Steel Fittings for doors & Windows comprising of handles,tower bolts,stays, hinges,aldrops with locks etc. complete job

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete semi-rigid pipe 32/40 mm dia

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Carriage of all materials

NASEER AHMAD WANI

M/S PRINCE ISHFAQ ALI

Javaid Ahmad Dev

VALLEY CONSTRUCTIONS

M/S HAJI MOHAMMAD AFZAL KUCHAY AND SONS

M/S MEHRAJ UD DIN MALLA

M/S GHULAM NABI TEELI

MR ARJUMAND RASOOL BHAT

M/S LONE AND SONS

New Zeal Construction Co

M/S NEW ALLIED